HUANUO Monitor Table Instruction Manual

Unpacking Instructions and Important Safety Information

• Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
• Check package contents against the Supplied Parts and Hardware to assure that all components were received undamaged. Do not use damaged or defective parts.
• Not all parts and hardware included will be used. If you require replacement parts, contact customer service at support@huanuoav.com.
• Carefully read all instructions before attempting installation.
• If you do not understand the instructions or have any concerns or questions, please contact customer service at support@huanuoav.com.
• This product may contain moving parts. Use with caution.
• Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. HUANUO disclaims any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Parts and Hardware

Hardware

Assembly Instructions

STEP 1: Connect Upper Pole to Lower Pole

Step 1-1: Loosen the screw [S] on pole [02] using Allen key [E] (1/8 in. (3mm)).

Step 1-2: Connect pole [01] to pole [02].

Step 1-3: Tighten the screw [S] using Allen key [E] to fix the two poles.

STEP 2A: For C Clamp Mounting

Step 2A-1: Install part [03] to pole [02] using screw [B] and Allen key [E] (1/8 in. (3mm)).

Step 1A-2: Adjust the mount according to the thickness of the desktop.

Step 1A-3: Install part [04] to part [03].

Step 1A-4: Secure the mount to the desktop using part [A] and Allen key [F] (15/64 in. (6mm)).

STEP 2B: For Grommet Mounting

Step 2B-1: Install part [09] to pole [02] using screws [B] and Allen key [E] (1/8 in. (3mm)).

Step 2B-2: Remove part [a] from part [04].

Step 2B-3: Secure the mount to the desktop using part [10] and Allen key [F] (15/64 in. (6mm)).

STEP 3: Install Cable Clips & Monitor Connector to the Pole Assembly

Step 3-1: Slide the two cable clips [07] and the monitor connector [05] to the pole assembly.

Step 3-2: Secure the monitor connector [05] to the pole assembly, then attach the cable clips [08] to the monitor connector [05] using Allen key [F] (15/64 in. (6mm)).

STEP 4: Check Monitor Hole Pattern and Select Monitor Bolts

Check the VESA mounting hole pattern on your monitor. The mount supports patterns up to 100x100 mm.

Bolt Length Verification: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns.

• Too short will not hold the monitor.
• Too long will damage the monitor.

Available bolts: M4x12mm (M-A) and M4x30mm (M-B).

STEP 5: Attach the Monitor Plates to the Monitors

For Flat Back Monitors (Universal Monitor Plate): Use bolts M-A and M-C.

For Round Back Monitors (Universal Monitor Plate): Use bolts M-B, M-C, and M-D.

STEP 6: Hang Monitors to the Stand and Secure with Knobs [C] and Bolts [D]

STEP 7: Fix Tilt Angle of the Monitors

Adjust the tilt angle using the provided bolt [F] (15/64 in. (6mm)).

STEP 8: Manage Cables

Route and secure cables using the provided cable clips.

STEP 9: Store Allen Keys into the Cable Clip

Store Allen keys [F] (15/64 in. (6mm)) and [E] (1/8 in. (3mm)) into the designated cable clip.

Features

Warning: To avoid tipping, please be careful not to extend the arms too far forward or backward. When you adjust the angle of the arms, please make sure two arms are balanced to avoid instability of the center of gravity of the base.

Individual VESA plate height adjustment helps monitors to be perfectly aligned.