HUANUO HNDS6/HNDS6W Desk Monitor Arm

Product Features

This desk monitor arm offers versatile positioning for your display, allowing for 360° rotation, 180° tilt, and +/- 85° tilt adjustment. It supports both C-Clamp and Grommet Mounting options.

Mounting Options:

• C-Clamp Mounting: Secures to the edge of a desk.
• Grommet Mounting: Installs through a pre-drilled hole in the desk.

Compatibility Check

Before installation, ensure your monitor meets the following requirements:

1. VESA Pattern: Your monitor must have a VESA mounting pattern of 75x75mm or 100x100mm. [Checkmark emoji] Yes - Compatible. [Cross emoji] No - Not compatible.
2. Weight Capacity: Your monitor, including accessories, must weigh less than 19.8 lbs (9 kg). [Checkmark emoji] Yes - Compatible. [Cross emoji] No - Not compatible.

Tools Needed (not included):

• Screwdriver
• Electric Drill (optional for grommet mounting)
• 7/16"-7/8" (11-22mm) Drill Bit (optional for grommet mounting)

Important Notes and Cautions

Note: Please read all instructions carefully before installation. Contact technical support or customer service if you have any questions. Not all included hardware may be used.

Caution: Avoid potential injuries and property damage. Do not use the product for purposes not specified in this manual. Do not exceed weight capacity. HUANUO is not liable for damage or injury due to improper mounting, assembly, or use. Verify all parts are included and undamaged before assembly. Do not use damaged or defective parts.

Warning: This product contains small parts that may be a choking hazard. The gas spring arms are under high pressure; do not puncture or expose to fire. Contact technical support for defective products. The information in this manual does not cover all possible installation conditions.

Tension Adjustment

Attention: DO NOT adjust tension without the monitor attached.

1. Ensure your monitor's weight is between 4.4-19.8 lbs (2-9 kg).
2. Verify monitor weight in its manual or on the manufacturer's website.
3. Confirm the monitor is securely attached to the mount.

Warning: The gas spring arm is under pressure and requires careful handling. Failure to follow instructions may result in damage or personal injury.

Parts List

• 01 Base x 1
• 02 C-Clamp Brace x 2
• 03 C-Clamp x 2
• 04 Lower Arm Section x 2
• 05 Upper Arm Section x 2
• A M6 x 12mm Bolt x 6
• B Grommet Bolt x 1
• C Nut x 1
• D Locking Plate x 1
• E 5/32" (4mm) Medium Allen Key x 1
• F 1/8" (3mm) Small Allen Key x 1
• G 3/16" (5mm) Large Allen Key x 1
• H M4 x 12mm Bolt x 8
• I M4 x 30mm Bolt x 8
• J L13mm Spacer x 8

Step 1: Install the Base

Note: For USB cable connection to the base, refer to Page 13.

For C-Clamp Mounting: Proceed to Option A.

For Grommet Mounting: Proceed to Option B.

Option A: For C-Clamp Mounting

Ensure your desk thickness is between 0.59"-3.54" (15-90mm).

Attach the C-Clamp Brace (02) to the Base (01) using Bolts (A) and the Medium Allen Key (E). Slide the assembled base onto the desk edge. Secure it using the C-Clamp (03), ensuring the clamp makes full contact with the desk or any necessary spacers.

Spacers: If your desktop is thin or has a crossbar, use a wood board or block as a spacer to ensure the C-clamp plate has full contact.

Option B: For Grommet Mounting

If your desk has a grommet hole, insert the Grommet Bolt (B) through the Base (01) and secure it with the Nut (C) from underneath. Ensure the grommet bolt is tightened securely.

If no grommet hole exists, mark a location at least 2" (50mm) from the desk edge and drill a hole using a 7/16"-7/8" (11-22mm) drill bit. Then, proceed with inserting the Grommet Bolt (B) and securing it.

Step 2: Attach the Arm Assembly to the Base

Connect the Lower Arm Section (04) to the Base (01). Ensure the cable cover on the lower arm faces down.

Connect the Upper Arm Section (05) to the Lower Arm Section (04).

Caution: Do not overtighten, as this may affect the rotation of the arms.

Use the Small Allen Key (F) to secure the connection.

Step 3: Hang the Monitors on the Mount

Choose the appropriate bolt (H or I) and spacer (J) configuration that fits your monitor's VESA holes. For flat-back monitors, use Bolts (H). For curved-back monitors, use Bolts (I) with Spacers (J).

Thread the top bolts into the monitor's VESA holes, but do not tighten completely.

Hang the monitor onto the VESA plate of the arm, aligning the top VESA slots or holes. Insert and tighten the bottom bolts to secure the monitor.

Note: You may need to grip the VESA plate like a steering wheel to rotate it.

Attention: HEAVY! You may need assistance with this step.

Use the Large Allen Key (G) to firmly tighten all bolts.

Note: The gas spring tension is preset for monitors weighing 4.4-11 lbs (2-5 kg). Release the monitor slowly after hanging to ensure it doesn't drop too quickly.

Step 4: Adjust Gas Spring Tension

Caution: To avoid damage to the monitor or mount, always keep the arm in a horizontal position while making adjustments. Assistance may be needed.

Hold the upper arm horizontally. Use the Large Allen Key (G) to adjust the gas spring tension bolt.

• If the monitor falls: Turn the bolt counter-clockwise ( '+' direction) to increase tension until the arm stays in position.
• If the monitor rises: Turn the bolt clockwise ( '-' direction) to decrease tension until the arm stays in position.

Once correctly adjusted, the arm should hold the monitor at any desired height.

Note: A QR code is provided in the original manual for an arm adjustment video.

Step 5: Swivel Restriction

Adjust the swivel restriction as needed by following the diagram.

Step 6: Tilt Adjustment

Adjust the monitor by gripping its edges. Do not press directly on the screen. If adjustment is difficult, loosen the tilt-lock bolt on the monitor plate connector. Adjust to the desired angle, then fully tighten the bolt.

Caution: Do not position or swivel the monitor beyond the edge of the desktop, as this may cause the unit to tip over.

Step 7: Monitor Rotation

Rotate the monitor to portrait or landscape orientation as desired by gripping the monitor edges.

Step 8: Route Cables Down the Arm

Securely route all monitor and power cables along the arm using the provided clips or channels. Use the Large Allen Key (G) to tighten the cable management covers.

Connecting USB Cables to the Base

Note: Female to Male USB Cables are not included.

1. Remove the USB cable cover from the base.
2. Snap off the two tabs on the cover.
3. Route your USB cables (female end) through the base, connecting them to the male USB ports inside.
4. Attach the cover back onto the base to secure the USB cables.

Attention: Be careful not to pinch the cables when reattaching the cover.

Support Information

HUANUO

• US/CA Support: 1-800-556-0533 (Mon-Fri 8am - 8pm CST)
• UK Support: 44-808-196-3874 (Mon-Fri 2pm - 10pm UTC)
• Email: support@huanuo.com
• Website: www.huanuo.com