Anker SoundCore 2 Bluetooth Speaker

About the Product

The Anker SoundCore 2 is a portable Bluetooth speaker designed for quality audio on the go.

[Image: A rectangular, dark-colored Anker SoundCore 2 Bluetooth speaker, viewed from the front-right. It has a mesh grille covering the front and sides, with the ANKER logo prominently displayed on the front grille. Buttons are visible on the top surface.]

Safety Instructions

• Do not drop the device.
• Do not disassemble the device.
• Do not immerse the device in water.
• Avoid extreme temperatures.
• Use original or certified cables.
• Do not use any abrasive cleaner or oil for cleaning.
• Do not use this device outdoors during thunderstorms.

Notices

?? This device complies with the radio interference requirements of the European Community.

♻️ This symbol indicates that the product should not be disposed of with regular household waste. It must be disposed of at an appropriate collection point for recycling at the end of its service life. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information, contact your local authorities, collection point, or the retailer where you purchased the product.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Statement

This device complies with general requirements regarding RF radiation. The device can be used as a portable device without any restrictions.

Charging SoundCore

LED Indicators:

• Flashing red: Low battery
• Solid red: Charging
• Solid white: Fully charged

To maintain long battery life, fully charge the battery at least once every 45 days.

[Image: Diagram illustrating the charging process of the SoundCore speaker. A USB cable is shown connecting the speaker to a power source. Visual cues indicate LED status: flashing red for low battery, solid red for charging, and solid white for fully charged.]

Turning On/Off

Press the power button to turn on the speaker. The indicator will light up white.

Press and hold the power button for 1 second to turn off the speaker. The indicator will also turn off.

Bluetooth Pairing

[Image: Diagrams illustrating Bluetooth pairing. One shows a button press action for entering pairing mode. Another shows a button press-and-hold action for canceling pairing. A third diagram depicts the speaker connected to a smartphone via Bluetooth.]

Actions:

• Press button: Enter pairing mode.
• Press and hold for 2 seconds: Cancel pairing of the connected device and re-enter pairing mode.

LED Indicators:

• Flashing blue: Pairing mode
• Solid blue: Connected to device

Upon powering on, the SoundCore will automatically connect to the last connected device if available. Otherwise, it will enter pairing mode.

Note: Keep Bluetooth devices within 1 meter (≤1m) for optimal pairing.

Connecting via AUX

[Image: Diagram showing the SoundCore speaker connected to an audio source via an AUX cable. The AUX cable is depicted as a separate accessory.]

A Sound Line AUX cable is sold separately.

To return to Bluetooth mode, disconnect the AUX cable from the SoundCore speaker.

Controls

Music Playback

Microphone

Phone Calls

Call Indicator:

• Solid blue: Call in progress
• Flashing blue: Incoming call

Technical Specifications

Distribution and Service

Czech Republic Distribution

Praha Music Center, s.r.o.

Ocelářská 937/39
190 00 Praha 9

Toll-free hotline: 800 876 066

Website: http://www.pmc.cz

Warranty and After-Sales Service

Praha Music Center, s.r.o.

Rakovnická 2665
440 01 Louny

Tel: +420226011197

Email: servis@pmc.cz