Anker SoundCore Boost
Owner's Manual
Product Number: A3145
Bluetooth Speaker / SoundCore Boost
Model: SM-A484-V01
Safety Instructions
- Avoid dropping.
- Do not disassemble.
- Do not submerge in water.
- Avoid extreme temperatures.
- Use original or certified cables.
- Do not use any corrosive cleaner/oil to clean.
- Do not use the device outdoors during thunderstorms.
Notice
This product complies with the radio interference requirements of the European Community.
This product is designed and manufactured with high quality materials and components, which can be recycled and reused.
This symbol [♻️] means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.
RF Warning Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Getting Started
Charge Your SoundCore
A diagram illustrates connecting the included USB cable to the SoundCore's charging port and a power source.
LED Indicator:
- One flashing white light: Low battery.
- Lights off: Fully charged.
To preserve battery lifespan, fully charge at least once every 45 days.
Charge USB Devices
A diagram shows connecting a USB device to the SoundCore's USB output port.
Turn On / Off
A diagram shows pressing and holding the power button [⏻] to turn the device on or off.
Bluetooth Pairing
Enter pairing mode: Press and hold the power button [⏻] for over 4 seconds. The LED indicator will flash blue rapidly.
Un-pair connected device and re-enter pairing mode: Press and hold the power button [⏻] for over 4 seconds.
Pairing mode: Rapidly flashing blue LED.
Connected to a device: Steady blue LED.
When turned on, SoundCore will automatically connect to the last connected device if available. If not, SoundCore will enter pairing mode.
NFC Pairing
Diagrams show tapping an NFC-enabled device to the NFC detection area on the SoundCore Boost to initiate pairing. A second diagram shows how to break the connection by tapping again.
Connect via AUX
Diagrams show connecting an AUX cable from an audio source to the SoundCore Boost's AUX input.
* SoundLine AUX cable sold separately.
To return to Bluetooth mode, remove the AUX cable from your SoundCore.
Controls
Music Playback
- Play / Pause: Press the power button [⏻] once.
- Skip forward: Press the power button [⏻] twice.
- Volume Up / Down: Press the '+' or '-' buttons.
- Super Bass: Press the 'UP' button once.
Call Handling
- Answer / End call: Press the power button [⏻] once.
- Reject call: Press and hold the power button [⏻] for 1 second.
- Put current call on hold and answer incoming call: Press the power button [⏻] once.
- Switch between held call and active call: Press and hold the power button [⏻] for 1 second.
- Transfer a call between speaker and mobile phone: Press the power button [⏻] once.
Voice Assistant
- Activate Siri / other voice control software: Press and hold the power button [⏻] for 1 second.
LED Indicator Status
- Steady blue: On a call.
- Flashing blue: Incoming call.
Specifications
Specifications are subject to change without notice.
| Feature | Specification |
|---|---|
| Input | 5V=2A |
| USB Output | 5V=1A |
| Play Time (varies by volume level and content) | 12 hours |
| Waterproof Rating | IPX5 |
| Weight | 585 g / 20.6 oz |
| Driver (full range) | 1.75" x 2 |
| Range | 20 m / 66 ft |
| Audio Output | 10 W × 2 |
| Charging Time | 4-6 hours |
| Battery Capacity | 5200 mAh |
| Size | 204 x 72 x 69 mm / 8 x 2.8 x 2.7 in |
| Impedance | 4 Ω |
| Frequency Response | 70 Hz - 20 KHz |
| Bluetooth Version | V4.2 |
Customer Service
Warranty: 18-month limited warranty.
Technical Support: Lifetime technical support.
Email: support@anker.com
Phone Support:
- US: 1-800-988-7973 (Mon-Fri 9:00-5:00 PST)
- DE: 069-9579-7960 (Mon-Fri 6:00-11:00)
- UK: 01604-936200 (Mon-Fri 6:00-11:00)
- JP: 03-4455-7823 (Mon-Fri 9:00-17:00)
- CN: 400-0550-036 (Mon-Fri 9:00-17:30)
Website: For FAQs and more information, please visit: anker.com/support
Social Media: @Anker @Anker Japan @Anker Deutschland @Anker O ce @Anker_JP
