eufy Video Doorbell Slim (1080p, Battery-Powered) Quick Start Guide
What's Included
The package contains the following items for Video Doorbell Installation:
- Video Doorbell Slim (1080p, Battery-Powered) - Model: T8220, FCC ID: 2AOKB-T8220, IC: 23451-T8220
- Mounting Bracket
- Screw Hole Positioning Card
- 15° Mounting Wedge (Optional)
- USB Charging Cable
- Screw Packs (includes spare screws and anchors)
- Doorbell Detaching Pin
- Quick Start Guide
For Wi-Fi Doorbell Chime Installation:
- Model: Wi-Fi Doorbell Chime - Model: T8020, FCC ID: 2AOKB-T8020, IC: 23451-T8020
- Power Plug (Note: Power plug may vary by region)
Product Overview
Video Doorbell (Battery Powered)
Front View:
- 1. Motion Sensor
- 2. Microphone
- 3. Camera Lens
- 4. Ambient Light Sensor
- 5. Status LED
- 6. Doorbell Button
- 7. Speaker
Rear View:
- 1. Micro USB Charging Port
- 2. SYNC/RESET button
- 3. Detaching Mechanism
Operation Guide
| Operation | How-to |
|---|---|
| Power on | Press and release the SYNC button. |
| Add doorbell to Wi-Fi Doorbell Chime | Press and hold the SYNC button until you hear a beep. |
| Power off the doorbell | Quick-press the SYNC button 5 times in 3 seconds. |
| Reset the doorbell | Press and hold the SYNC button for 10 seconds. |
How the System Works
The video doorbell system consists of two main components:
- The video doorbell unit installed at your door.
- The Wi-Fi Doorbell Chime located inside your house.
The video doorbell is designed to detect motion at your porch and allow you to answer the door from anywhere, anytime. The Wi-Fi Doorbell Chime serves as an indoor digital chime and stores video clips onto a microSD card (which must be provided by the user). When someone rings the doorbell, occupants within the house will receive a notification.
Diagram Description: A visual shows the doorbell mounted outside a house, wirelessly communicating with a chime unit inside. Another diagram illustrates the doorbell detecting motion and sending a notification.
Step 1: Powering on the Wi-Fi Doorbell Chime
Connect the Wi-Fi Doorbell Chime to the Internet
- Attach the Power Connector: Place the power connector over the Wi-Fi Doorbell Chime, aligning the raised slots with the notch on the chime's base. Rotate clockwise to secure the connector.
- Extend Antennas: Extend the Wi-Fi Doorbell Chime's antennas.
- Connect to Power: Plug the Wi-Fi Doorbell Chime into an AC power supply. The LED indicator will turn solid green when the chime is ready for setup.
Diagram Description: Illustrations show the power connector being attached to the chime unit and the chime unit with its antennas extended.
Step 2: Setting up the System
Download the App and Set up the System
Download the eufy Security app from the App Store (for iOS devices) or Google Play (for Android devices).
Sign up for a eufy Security account and follow the on-screen instructions to complete the setup. Tap 'Add Device' and add the following devices:
- Add the Wi-Fi Doorbell Chime.
- Add the doorbell.
Visual Description: Icons representing the App Store and Google Play are displayed.
Step 3: Charging Your Doorbell
The doorbell is shipped with an 80% battery charge for safe transportation. It is recommended to fully charge the doorbell before mounting it at your front door.
Diagram Description: An illustration shows the doorbell connected to a USB cable and a power source for charging.
Note: Battery life varies based on usage. In typical scenarios, with up to 15 events per day and each recording lasting 20 seconds on average, the doorbell battery can last up to 4 months.
LED Indication:
- Charging: Solid orange
- Fully charged: Solid blue
Charging Time: Approximately 6 hours from 0% to 100%.
Step 4: Finding a Mounting Spot
Find a Mounting Spot
Take the Video Doorbell to your front door. Use the eufy Security app to check the live view and identify a position that provides the desired field of view.
Consider the following factors:
- Check if existing holes and anchors on the wall or door frame can be reused.
- If placing the doorbell near a side wall, ensure the wall does not appear in the field of view to prevent IR light reflection and blurry night vision.
- If drilling new mounting holes, the recommended mounting height is 48 inches (1.2m) from the ground.
- The 15° mounting wedge can be used as a supplementary mounting bracket to improve the view on a specific side.
Diagram Description: Visuals illustrate height references (1.76m, 1m, 1.2m, 0.3m) and compare the field of view with and without the 15° mounting wedge. Another diagram shows the Screw Hole Positioning Card being placed against the wall to mark drilling points.
Step 5: Mounting the Bracket
Mount the Doorbell on a Wooden Surface
If mounting on a wooden surface, pre-drilling pilot holes is not necessary. Use the provided screws to secure the Mounting Bracket to the wall. The Screw Hole Positioning Card indicates the screw hole positions.
Required items: Power Drill, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs.
Diagram Description: Illustrations show required tools like a Phillips-Head Screwdriver and the components. Further diagrams depict the Mounting Bracket attached to the wall, both with and without the 15° Mounting Wedge.
Mount the Video Doorbell on Surfaces Made Out of Hard Materials
- For hard surfaces like brick, concrete, or stucco, drill two holes using a 15/64” (6mm) drill bit through the Screw Hole Positioning Card.
- Insert the provided anchors into the holes, then use the provided long screws to secure the Mounting Bracket to the wall.
Required items: Power Drill, 15/64” (6mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs.
Diagram Description: Illustrations show required tools including a Power Drill with a 1/4" (6.35mm) Drill Bit and a 15/64" (6mm) Drill Bit, along with the components. Further diagrams show the Mounting Bracket attached to the wall, both with and without the 15° Mounting Wedge.
Step 6: Mounting the Doorbell
Mount the Doorbell
Align the doorbell with the top of the mount and then snap the bottom into place.
Diagram Description: An illustration shows the doorbell being attached to the mounted bracket.
You're all set! For instructions on detaching the doorbell or recharging it, please refer to the relevant sections.
Appendix 1: Detaching the Doorbell
Detach the Doorbell
- Use the provided doorbell detaching pin to detach the doorbell from the Mounting Bracket.
- Insert and press the detaching pin into the hole located at the bottom of the doorbell, then lift to remove the bottom of the doorbell.
Required item: Doorbell Detaching Pin.
Diagram Description: An illustration shows the Doorbell Detaching Pin and the process of inserting it into the doorbell to release it.
Appendix 2: Recharging the Doorbell
Recharge the Doorbell
Charge the doorbell using universal USB chargers that provide a 5V 1A output.
Diagram Description: An illustration shows the doorbell connected via a USB cable to a power source.
LED Indication:
- Charging: Solid orange
- Fully charged: Solid blue
Charging Time: Approximately 6 hours from 0% to 100%.
Notice
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The minimum separation distance is 20cm.
Notice: Shielded Cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
US Importer Information:
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: 1-800-988-7973
CE Declaration of Conformity
This product complies with the radio interference requirements of the European Community (CE marking). Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the full declaration of conformity, visit: https://www.eufylife.com/. This product can be used across EU member states.
Environmental Conditions: Do not use the Device in environments with excessively high or low temperatures, or expose it to strong sunshine or excessive moisture. The suitable operating temperature for T8020 and accessories is 0°C-40°C. The suitable operating temperature for T8220 and accessories is -20°C-50°C. When charging, place the device in an environment with normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature ranging from 5°C to 25°C.
RF Exposure Information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of 20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use products that maintain a 20cm distance between the device and the human body.
Caution: Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Technical Specifications:
- Wi-Fi Operating Frequency Range: 2412~2472MHz (2.4G)
- Wi-Fi Max Output Power: 19dBm (ERIP for T8020); 15dBm (ERIP for T8220)
- Bluetooth Operating Frequency Range: 2402~2480MHz; Bluetooth Max Output Power: 8dBm (EIRP)
EU Importer Information:
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom
This product is designed and manufactured with high-quality materials and components, which can be recycled and reused.
Disposal Information
This symbol indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. (Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.)
IC RF Statement:
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. (Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matière d'exposition RF.)
Customer Service
Warranty
12-month limited warranty
Contact Information:
- US: +1 (800) 988 7973 (Mon-Fri 9:00-17:00 PT)
- UK: +44 (0) 1604 936 200 (Mon-Fri 6:00-11:00 GMT)
- DE: +49 (0) 69 9579 7960 (Mon-Fri 6:00-11:00)
- Customer Support Email: support@eufylife.com
Company Address:
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Social Media:
- Facebook: @EufyOfficial
- Twitter: @EufyOfficial
- Instagram: eufyofficial
