eufy Security Video Doorbell 1080p (Battery-Powered)

What's Included

This section details the components provided for the Video Doorbell and Wi-Fi Doorbell Chime installation.

• Video Doorbell 1080p (Battery-Powered): Model T8222. Features FCC ID: 2AOKB-T8220 and IC: 23451-T8220. This is the main doorbell unit.
• Mounting Bracket: A bracket for attaching the doorbell to a wall or surface.
• Screw Hole Positioning Card: A template to help mark drilling locations accurately.
• 15° Mounting Wedge (Optional): An accessory to adjust the doorbell's viewing angle.
• USB Charging Cable: A standard cable for charging the doorbell's battery.
• Screw Packs: Contains screws and wall anchors for mounting the bracket.
• Doorbell Detaching Pin: A tool used to remove the doorbell from its mount.
• Quick Start Guide: This document.
• Wi-Fi Doorbell Chime: Model T8020. Features FCC ID: 2AOKB-T8020 and IC: 23451-T8020. This indoor chime connects to your Wi-Fi network.
• Power Plug: Connects the Wi-Fi Doorbell Chime to a power outlet. Note: The power plug design may vary by region.

Product Overview

Video Doorbell (Battery Powered)

Front View:

Diagram shows the front of the doorbell with numbered components: 1. Motion Sensor, 2. Microphone, 3. Camera Lens, 4. Ambient Light Sensor, 5. Status LED, 6. Doorbell Button, 7. Speaker.

Rear View:

Diagram shows the rear of the doorbell with numbered components: 1. Micro USB Charging Port, 2. SYNC/RESET button, 3. Detaching Mechanism.

Operation Guide

How the System Works

The video doorbell system consists of two main parts:

• The video doorbell unit mounted at your door.
• The Wi-Fi Doorbell Chime located inside your home.

The video doorbell detects motion and allows you to answer visitors remotely. The Wi-Fi Doorbell Chime acts as an indoor digital chime and can store video clips on a microSD card (not included). When someone rings the doorbell, occupants inside the house are notified.

Diagram illustrates the system: A Video Doorbell is mounted outside a house, wirelessly connected to a Wi-Fi Doorbell Chime inside the house, which is plugged into a power source. A car is visible in the driveway.

Step 1: Powering on the Wi-Fi Doorbell Chime

Connect the HomeBase 2 to the Internet (Note: The document refers to HomeBase 2, but the product is Wi-Fi Doorbell Chime. Assuming this is a general instruction or a previous model reference).

1. Fix the power connector to Wi-Fi Doorbell Chime:
   1. Place the power connector over the Wi-Fi Doorbell Chime, aligning with the indicated direction.
   2. Align the raised slots of the power connector with the notch on the base of the chime.
   3. Rotate clockwise to secure the power connector.
2. Extend Wi-Fi Doorbell Chime's antennas: Two antennas are shown extending from the chime unit.
3. Plug Wi-Fi Doorbell Chime into an AC power supply: Connect the chime to a wall outlet. The LED indicator will turn solid green when it is ready for setup.

Step 2: Setting up the System

Download the App and Set up the System

Download the eufy Security app from the App Store (for iOS devices) or Google Play (for Android devices).

Icons for "Download on the App Store" and "Get it on Google Play" are described.

Sign up for a eufy Security account and follow the on-screen instructions to complete the setup. Tap 'Add Device' and add the following:

1. Add the Wi-Fi Doorbell Chime.
2. Add the doorbell.

Diagram shows a smartphone with the eufy Security app, indicating the process of adding devices.

Step 3: Charging Your Doorbell

The doorbell is shipped with an 80% battery charge for safe transportation. It is recommended to fully charge the doorbell before mounting it at your front door.

Diagram shows a USB charging cable connected to the doorbell.

Note: Battery life varies with usage. In typical scenarios with up to 15 events per day and 20-second recordings, the battery can last up to 4 months.

Charging time: 6 hours from 0% to 100%.

Step 4: Finding a Mounting Spot

Find a Mounting Spot

Use the eufy Security app to view the live feed from the Video Doorbell at your front door. Choose a position that provides your desired field of view.

Consider the following factors:

1. Check for existing holes and anchors on the wall or door frame that can be reused.
2. If placing the doorbell near a side wall, ensure the wall is not visible in the frame to prevent IR light reflection, which can blur night vision.
3. For first-time installations, the recommended mounting height is 48 inches (1.2m) from the ground.
4. Use the 15° mounting wedge as a supplementary bracket if needed to adjust the viewing angle.

Diagrams illustrate recommended mounting heights and the effect of the 15° mounting wedge on the viewing angle. Another visual shows using the Screw Hole Positioning Card to mark wall positions.

Step 5: Mounting the Bracket

Mount the Doorbell on a Wooden Surface

If mounting on wood, pre-drilling pilot holes is not necessary. Use the provided screws to secure the Mounting Bracket. The Screw Hole Positioning Card indicates screw hole placement.

What is required: Power Drill, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs.

Diagrams show the Mounting Bracket being attached to a wall, with and without the 15° Mounting Wedge. Required tools are listed: Phillips-Head Screwdriver (user-provided), Power Drill with 1/4" (6.35mm) Drill Bit (user-provided).

Mount the Video Doorbell on Surfaces Made Out of Hard Materials

1. For hard surfaces like brick, concrete, or stucco, drill 2 holes using the Screw Hole Positioning Card and a 15/64" (6mm) drill bit.
2. Insert the provided anchors, then use the longer screws to secure the Mounting Bracket.

What is required: Power Drill, 15/64" (6mm) Drill Bit, Mounting Bracket, 15° Mounting Wedge (Optional), Screw Packs.

Diagrams show the process for hard surfaces, including drilling, anchors, and screw attachment. Required tools are listed.

Step 6: Mounting the Doorbell

Mount the Doorbell

Align the top of the doorbell with the mount, then snap the bottom into place.

Diagram shows the doorbell being attached to the bracket by aligning the top and snapping the bottom.

You are all set! For instructions on detaching or recharging the doorbell, refer to the following sections.

Appendix 1: Detaching the Doorbell

Detach the Doorbell

Use the provided doorbell detaching pin to detach the doorbell from the Mounting Bracket.

1. Insert and press the detaching pin into the hole at the bottom of the doorbell.
2. Lift to detach the bottom of the doorbell.

What is required: Doorbell Detaching Pin.

Diagram illustrates the detaching pin being inserted into the bottom of the doorbell to release it.

Appendix 2: Recharging the Doorbell

Recharge the Doorbell

Charge the doorbell using universal USB chargers that provide a 5V 1A output.

Diagram shows a USB cable connecting to the doorbell's charging port.

Notice

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The minimum separation distance is 20cm.

Notice: Shielded Cables

All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Importer Information:

• Company Name: POWER MOBILE LIFE, LLC
• Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
• Telephone: 1-800-988-7973

Declaration of Conformity (CE)

This product complies with the radio interference requirements of the European Community.

Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the website: https://www.eufylife.com/.

This product can be used across EU member states.

Environmental Guidelines:

• Do not use the Device in environments with excessively high or low temperatures, or expose it to strong sunshine or excessive moisture.
• Suitable temperature for T8020 and accessories: 0°C-40°C.
• Suitable temperature for T8222 and accessories: -20°C-50°C.
• When charging, ensure the device is in an environment with normal room temperature and good ventilation.
• Recommended charging temperature range: 5°C~25°C.

RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of 20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use the product maintaining a 20cm distance from the human body.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Wi-Fi Operating Frequency Range: 2412~2472MHz (2.4G)

Wi-Fi Max Output Power: 15.68dBm (ERIP for T8020); 15.01dBm (ERIP for T8220)

Bluetooth Operating Frequency Range: 2402~2480MHz; Bluetooth Max Output Power: 2.048dBm (EIRP)

EU Importer Information:

• Importer: Anker Technology (UK) Ltd
• Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IC RF Statement

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. (French: Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matière d'exposition RF.)

Disposal Information

This symbol indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling protect natural resources, human health, and the environment. For more information, contact your local municipality, disposal service, or the shop where the product was purchased.

Customer Service

Warranty

12-month limited warranty.

Contact Information

• US: +1 (800) 988 7973 (Mon-Fri 9:00-17:00 PT)
• UK: +44 (0) 1604 936 200 (Mon-Fri 6:00-11:00 GMT)
• DE: +49 (0) 69 9579 7960 (Mon-Fri 6:00-11:00)

Customer Support Email: support@eufylife.com

Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

Follow Us

• Facebook: @EufyOfficial
• Twitter: @EufyOfficial
• Instagram: eufyofficial