GLACIER EZ-FIT DISTRO PLATE NV SERIES INSTALLATION GUIDE
Models Covered
This manual is for the following models:
- Model Nr.: PH-GEF_DIS-NV5, Product: Glacier EZ-Fit Distro Plate NV5, Color: Acrylic
- Model Nr.: PH-GEF_DIS-NV7, Product: Glacier EZ-Fit Distro Plate NV7, Color: Acrylic
- Model Nr.: PH-GEF_DIS-NV9, Product: Glacier EZ-Fit Distro Plate NV9, Color: Acrylic
Legend
The following symbols are used in this manual:
- Remove: Indicates parts to be removed.
- Install: Indicates parts to be installed.
- Loosen: Indicates screws or parts to be loosened.
Scope of Delivery
The following components are included:
- Mounting Hooks: 4x
- M3x16 Screw: 4x
- Hex Key 2.5 mm: 1x
- Hex Key 2 mm: 1x
- D-RGB Cable: 1x
- Distro Plate: 1x (for NV5, NV7, NV9 models)
- Fitting Insert Soft Tube: 3x
- M4x25 Screw: 4x
Note: The pump is not included with PH-GEF_DIS-NVX models. The image is for installation reference only.
Important Warnings
This product is intended for advanced users. Improper installation may result in damage to your equipment.
Phanteks assumes no liability for damages occurring to components due to the use of Phanteks cooling products, whether due to errors or omissions in instructions or product defects.
Do not disassemble the water block. Warranty will be voided.
The manual also contains warnings in German, French, Spanish, and Chinese, emphasizing user experience and potential damage from incorrect installation.
Installation Steps
Step 1: Plan the Waterloop
This step involves planning the layout of your PC's water cooling loop. A diagram illustrates the typical flow path, showing connections from the radiator to the pump, CPU, GPU, and back to the radiator, including fill and drain ports.
Step 2: Prepare NV Chassis
This step involves preparing the PC chassis. It shows how to remove side panels.
PRO TIP: For NV5 chassis, remove the bottom fan bracket.
Step 3: Install Distro Plate
This section details the installation of the distro plate.
01 Install Mounting Hooks: Install the provided mounting hooks into the chassis.
02 Install & Secure Distro Plate: Mount the distro plate using the hooks and screws (M3x16).
Step 4: Secure NV Distro Plate
This step focuses on securing the distro plate further.
01 Install Bottom Hooks: Install the bottom hooks.
02 Secure Bottom: Secure the bottom of the distro plate with screws.
Step 5: Adjust Sliders
This step involves adjusting alignment sliders.
A CPU Alignment: Adjust sliders for proper CPU alignment.
B GPU Alignment: Adjust sliders for proper GPU alignment.
Step 6: Install Tube
This section covers tube installation for both hard and soft tubing.
A Hard Tube Installation: Instructions for installing hard tubes (visual shows a tube being inserted).
B Soft Tube Installation:
- PRO TIP: Please put a drop of water into the fitting O-ring before installation to aid sealing.
- Ensure tubes are cut perpendicular to the tubing as shown in the diagram.
- For a tight seal, insert the tube straight into the fitting and press until a slight click is heard.
- Install the Soft Tube Insert into the fitting.
Remove Tube: To remove a tube, press down on the ring before removing the tube, and keep the ring pressed while removing the tube.
Step 7: D-RGB Cables
This step covers connecting the D-RGB lighting cables.
Connect the D-RGB cable from the distro plate to a controller or an optional mainboard adapter.
Follow the mainboard manual for instructions on RGB control and syncing lighting to the mainboard.
The diagram shows connecting the D-RGB cable, an optional mainboard adapter, and mentions expanding with more D-RGB products.
Safety Information
To achieve maximum safety, follow these guidelines:
- Place the product on a clean, stable surface with adequate ventilation.
- Avoid placing the product near water, moisture, or wet surfaces, or near heat sources like radiators, stoves, or open flames.
- Exercise caution when operating the PC to avoid electrical shock. This includes unplugging during thunderstorms, ensuring hands are dry, keeping the PC away from liquids and heat, and taking other reasonable precautions.
- Carefully plan wire placement when connecting external devices. Protect cables from being stepped on or pinched, especially at connectors.
- Handle glass components with extra caution during removal/reattachment. Place removed glass components on a stable surface.
- When unplugging devices or cables, pull the plug or connector, not the cord.
- Do not place heavy items on top of the product.
- Ensure the PC is off, unplugged, and all connected devices are powered off and unplugged before installing or uninstalling internal components.
Note on Disposal
The WEEE symbol (Waste Electrical and Electronic Equipment) indicates that this product must not be disposed of with normal household waste. Proper disposal helps protect the environment. Contact your local municipality, waste disposal service, or the retailer for more information.
Phanteks
