WORKPRO GS920140 20-Inch 5-Drawer Cabinet Chest

Safety Information ⚠️

To reduce the risk of injury, please read and follow the safety instructions below before assembling and using this product.

1. This product is not designed for commercial or industrial storage.
2. This product is intended for indoor use only.
3. Do not alter this product in any manner. For example, do not weld external lock bars or attach electrical equipment.

[Caution]: Do not attach or mount this product to a vehicle or mobile trailers. This may cause personal injury or product damage. Mounting this product to any vehicle or mobile trailers in any manner will void warranty.

[Caution]: Do not stand on this product. You may fall which may cause personal injury or product damage.

[Caution]: Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an unlevel surface, which may cause personal injury or product damage.

[Caution]: Lock the door if moving this product. The doors could come open and make the product unstable and tip, which may cause personal or product damage.

Specifications

Maximum Load Capacity: 154 lbs.

[Note]: Begin product assembly close to the final intended location of your cabinet. This product is heavy and may be difficult to move after assembly.

Package Contents

Hardware Included

Note: Hardware not shown to actual size.

Additional Tools Required for Assembly (Not Included): Phillips Screwdriver ➕

Package Contents (Continued)

Assembly Instructions

[Caution]: Two people are recommended for assembly.

Step 1: Lift Chest Out of Cabinet

Turn cabinet upside down. Remove all bolts (CC), washers (DD), and nuts (BB) from the base cabinet using the provided 12mm wrench (AA). Save all for caster installation.

Diagram Description: Shows the cabinet flipped over, with arrows indicating the removal of bolts, washers, and nuts from the base.

Step 2: Remove Base From Chest

Remove all 4 Philips head screws from the bottom and discard.

Diagram Description: Shows the bottom of the chest with arrows pointing to the 4 Philips head screws to be removed.

Step 3: Re-Attach Base and Casters to the Bottom of the Cabinet

Attach bolts (CC), washers (DD), and nuts (BB) using the provided 12mm wrench (AA) as shown.

Diagram Description: Shows the base with casters being re-attached to the cabinet bottom using bolts, washers, and nuts.

Step 4: Riser Assembly

Assemble the sides and the back (flange side up) together using the bolts (FF) and nuts (EE) provided.

Note: When assembled, the riser should be the same size, left to right, as the chest.

Diagram Description: Shows the two side panels and the back panel of the riser being joined with bolts and nuts.

Step 5: Assemble Riser With Chest and Cabinet

Lock the chest and lay it on its' back. Line up the riser assembly with holes in the chest bottom. Secure with screws (GG) provided.

Position the chest with the attached riser on the cabinet. Secure the riser bottom to the cabinet top with screws (GG) provided.

Diagram Description: Illustrates attaching the riser to the chest bottom with screws, then placing the chest/riser onto the cabinet and securing it.

Step 6: Lubricate Drawer Slides Periodically

Hardware (nuts, bolts, washers) should be tightened periodically.

Diagram Description: A general illustration indicating the need to check and tighten hardware.

Maintenance

1. Caster Maintenance

Grease the casters annually using high-quality bearing grease.

Diagram Description: A visual of a caster wheel.

2. Drawer Maintenance

Lubricate the slides semi-annually.

Periodically clean the drawer fronts, drawer trim, and other surfaces with a mild detergent and water.

Auto wax preserves the storage unit's luster finish and protects against scratches. Apply the wax as you would on a car.

Remove grease and oil with a standard nonflammable cleaning fluid.

Diagram Description: A visual of a drawer slide mechanism.

Replacement Parts

Diagram Description: An exploded view of the cabinet chest showing the arrangement of all replacement parts.