WORKPRO Metal Garage Storage Cabinet
Model: W082094AE
Dimensions: 31.5"W x 15.75"D x 71"H
[Safety Icon: Use Precaution] [Safety Icon: Instruction Manual] [Safety Icon: Eye Protection] [Safety Icon: Protective Gloves]
Safety Information
General Safety Information
To reduce the risk of serious injury, read and follow the safety instructions below before assembling and using this product.
- This product is intended for indoor use only.
- This product is not designed for commercial nor industrial usage.
CAUTION!
- Do not exceed 180lbs per shelf of evenly distributed weight. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
- Evenly distribute the weight on each shelf, and keep the heaviest loads on the bottom shelf and smaller lighter items on the upper level.
- Use at least two people to move, assemble or install this product.
- Any assembly or maintenance of the product must be carried out by adults only.
- Close and lock the doors before moving this product.
- Use only on flat, level and hard surface capable of supporting the cabinet and any items placed on it.
- Maintain proper footing and balance at all times.
WARNING!
- The metal may have sharp edges or corners. The use of protective gloves is recommended.
- Do not alter this product in any manner. For example, do not weld external bar locks or attach electrical equipment. This may cause product damage or personal injury.
- Keep the product on level surfaces. The product could become unstable and it may tip over if stored or moved on an uneven surface, which may cause personal injury, death or product damage.
- DO NOT leave children unattended near this product. Cabinet may tip over if improperly opened.
- DO NOT stand on the product and do not use it as scaffold.
Specifications
| Specification | Value |
|---|---|
| Maximum Load Capacity of each shelf (evenly distributed) | 180 lbs |
Package Contents
Tools Required (Not Included)
- [Protective Gloves]
- [PH2 Phillips Screwdriver]
- [Electric Drill]
NOTE: When using the electric drill, to avoid damage to screw or holes, do not tighten the screws.
Parts List
| Part | Description | Qty |
|---|---|---|
| A | Top panel | 1 |
| B | Top bracket | 1 |
| C | Left door | 1 |
| D | Left side panel | 1 |
| E | Left back panel | 1 |
| F | Right back panel | 1 |
| G | Right side panel | 1 |
| H | Right door | 1 |
| I | Shelf | 4 |
| J | Bottom panel | 1 |
| K | Bottom bracket | 1 |
| L | Corner bracket | 4 |
| M | Adjustable foot | 4 |
| N | Key | 4 |
| O | Bottom hinge pin | 2 |
| P | Washer | 2 |
| Q | Plastic shelf locking clips | 16 |
| R | Metal shelf clip | 16 |
| AA | #5 x 10mm self-tapping screw | 40 |
NOTE: Panels D,E,F&G and Door C&H are labeled with arrows pointing up.
Assembly
NOTE: Assemble on a flat surface. A piece of cardboard is recommended to keep the product from being scratched during assembly.
Two people are recommended for assembly.
STEP 1: ATTACH THE BACK PANELS
Align and attach the left back panel (E) to the right back panel (F) with three screws (AA). Tighten securely.
[Diagram Description: The left back panel (E) and right back panel (F) are shown being joined at their edges. Three screws (AA) are indicated for fastening. A detail view shows the screw connection.] [Watermark: WORKPRO]
| Part | E | F | AA |
|---|---|---|---|
| DESCRIPTION | Left back panel | Right back panel | Screw |
| QTY | 1 | 1 | 3 |
STEP 2: ATTACH THE LEFT SIDE PANEL
Align and attach the left side panel (D) to the back panels (E&F) at right angles and tighten with three screws (AA) at the three indicated locations.
[Diagram Description: The left side panel (D) is attached perpendicularly to the joined back panels (E & F). Three screws (AA) secure the connection at three points. A detail view shows the screw connection.] [Watermark: WORKPRO]
| Part | D | E | F | AA |
|---|---|---|---|---|
| DESCRIPTION | Left side panel | Left back panel | Right back panel | Screw |
| QTY | 1 | 1 | 1 | 3 |
STEP 3: ATTACH THE RIGHT SIDE PANEL
Align and attach the right side panel (G) to the back panels (E&F) at right angles and tighten with three screws (AA) at the three indicated locations.
[Diagram Description: The right side panel (G) is attached perpendicularly to the joined back panels (E & F). Three screws (AA) secure the connection at three points. A detail view shows the screw connection.] [Watermark: WORKPRO]
| Part | E | F | G | AA |
|---|---|---|---|---|
| DESCRIPTION | Left back panel | Right back panel | Right side panel | Screw |
| QTY | 1 | 1 | 1 | 3 |
STEP 4: ATTACH THE TOP BRACKET
Attach the top bracket (B) to the side panels (D&G) and tighten with two screws (AA) each side (totally four screws).
[Diagram Description: The top bracket (B) is positioned across the top edges of the side panels (D & G). Two screws (AA) are shown securing the bracket to each side panel. A detail view shows the screw connection to the back of the top bracket.] [Watermark: WORKPRO]
| Part | B | D | G | AA |
|---|---|---|---|---|
| DESCRIPTION | Top bracket | Left side panel | Right side panel | Screw |
| QTY | 1 | 1 | 1 | 4 |
STEP 5: ATTACH THE BOTTOM BRACKET
Attach the bottom bracket (K) to the side panels (D&G) and tighten with two screws (AA) each side (totally four screws).
[Diagram Description: The bottom bracket (K) is positioned across the bottom edges of the side panels (D & G). Two screws (AA) are shown securing the bracket to each side panel. A detail view shows the screw connection to the back of the bottom bracket.] [Watermark: WORKPRO]
| Part | D | G | K | AA |
|---|---|---|---|---|
| DESCRIPTION | Left side panel | Right side panel | Bottom bracket | Screw |
| QTY | 1 | 1 | 1 | 4 |
STEP 6: ATTACH THE BOTTOM PANEL
Slide the bottom panel (J) to the cabinet frame and secured with a screw (AA) on the bottom. Make sure the notch on the edge of bottom panel (J) face forward.
[Diagram Description: The bottom panel (J) is slid into place at the base of the cabinet frame. A screw (AA) secures it from underneath. A detail view highlights the notch on the front edge of the bottom panel.] [Watermark: WORKPRO]
| Part | J | AA |
|---|---|---|
| DESCRIPTION | Bottom panel | Screw |
| QTY | 1 | 1 |
STEP 7: ATTACH THE TOP PANEL
Attach the top panel (A) to the top of the cabinet frame and secured with three screws (AA) each side (totally six screws). Make sure the symbol “H” on the edge of top panel (A) face forward.
NOTE: Install the front edge with symbol “H” first. The six screws (AA) shown above are installed along the inside edge of top panel (A).
[Diagram Description: The top panel (A) is placed on top of the cabinet frame. Six screws (AA) are used to secure it, with three on each side. The front edge of the top panel has a symbol 'H' which should face forward.] [Watermark: WORKPRO]
| Part | A | AA |
|---|---|---|
| DESCRIPTION | Top panel | Screw |
| QTY | 1 | 6 |
STEP 8: ATTACH THE CORNER BRACKET
Attach four corner brackets (L) to the bottom of cabinet and secured with sixteen screws (AA).
[Diagram Description: Four corner brackets (L) are attached to the underside corners of the cabinet. Sixteen screws (AA) are used for this purpose. A detail view shows the bracket and screw placement.] [Watermark: WORKPRO]
| Part | L | AA |
|---|---|---|
| DESCRIPTION | Corner bracket | Screw |
| QTY | 4 | 16 |
STEP 9: ATTACH THE ADJUSTABLE FEET
Install four adjustable feet (M) to the bottom of cabinet clockwise and tighten to level.
[Diagram Description: Four adjustable feet (M) are screwed into the bottom of the cabinet. A detail view shows the foot being screwed in.] [Watermark: WORKPRO]
| Part | M |
|---|---|
| DESCRIPTION | Adjustable foot |
| QTY | 4 |
STEP 10: INSTALL THE SHELVES
Before placing shelves, place four metal clips (R) into perforated slots at the same height for each shelf location.
NOTE: The holes between the slots help with horizontal positioning.
Place the shelves (I) on top of metal clips (R).
After installing shelves, place a plastic clip (Q) at corner to lock shelves in place.
Tip: Inserting one end of plastic clip (Q) next to the panel and squeezing the other end helps install well.
[Diagram Description: Metal shelf clips (R) are inserted into the side panel slots. Shelves (I) are then placed on these clips. Plastic shelf locking clips (Q) are used at the corners to secure the shelves. Detail views of clip installation.] [Watermark: WORKPRO]
| Part | I | Q | R |
|---|---|---|---|
| DESCRIPTION | Shelf | Plastic shelf locking clip | Metal shelf clip |
| QTY | 4 | 16 | 16 |
STEP 11: ATTACH THE DOORS
Install bottom hinge pin (O) and washer (P) on each side of the bottom bracket (K). Make sure the washer (P) is on the bottom hinge pin (O).
Lower the left door (C) onto bottom left bottom hinge pin, then swing the left door (C) into top bracket (B) while pulling down on the latch, align latch with hole in top bracket (B) and release when latch is in position.
Repeat above step for right door (H).
Insert key (N) into lock to verify proper operation.
[Diagram Description: Bottom hinge pins (O) and washers (P) are installed on the bottom bracket (K). The left door (C) is hung on the bottom hinge pin and then attached to the top bracket (B) via its latch mechanism. The right door (H) is attached similarly. A key (N) is shown being inserted into the lock.] [Watermark: WORKPRO]
| Part | C | H | N | O | P |
|---|---|---|---|---|---|
| DESCRIPTION | Left door | Right door | Key | Bottom hinge pin | Washer |
| QTY | 1 | 1 | 1 | 2 | 2 |
STEP 12: ADJUST THE LEVEL WITH ADJUSTABLE FEET
Adjust each adjustable foot (M) to the desired elevation by turning the adjustable foot counterclockwise to elevate and clockwise to lower the adjustable foot.
[Diagram Description: The adjustable feet (M) at the bottom of the cabinet are shown being turned to level the cabinet.] [Watermark: WORKPRO]
| Part | M |
|---|---|
| DESCRIPTION | Adjustable foot |
| QTY | 4 |
Cleaning and Maintenance
Follow standard cleaning procedures for metal cabinets. Use a damp cloth and mild detergent if necessary. Avoid abrasive cleaners.
Customer Service
Ensure all components are present. If any components are missing, do not proceed with assembly. Please send an email to service@greatstartools.com or call 877-876-7562.
Visit us at: www.greatstartools.com
Distributed by: Hangzhou GreatStar Industrial Co., Ltd.
Made in China
