4Modern Home 7030-3BK Operations Manual
Product Information
Model: 7030-3BK
Brand: 4Modern Home
Made in China
Where to Place Your Outdoor Wall Lights
If you have one light next to your entryway or garage door, it should be 1/3 of the height of the door. If placing one light on each side of the door, the lights should be 1/4 of the height of the door. Measure from the floor to the top of your door, then divide by 4 for two lights or 3 for one light. For example, if your door is 80" tall, divide by 4, and buy two lights that are each 20" tall. The lights should also be placed 66" from the floor or ground to properly illuminate the lock and handle. Lights should also be placed 6" from the edge of the door. If you choose to have only one light, make sure it is placed on the side of the door closest to the door handle.
Helpful Tip: This product is equipped with a dusk-to-dawn sensor. Please pay attention to the installation height to ensure that no objects such as eaves cover the sensor, as this may cause the light to remain on constantly.
Diagram Description: A drawing shows a house with a wall light fixture. Dimensions indicate a 26.5" tall fixture, with placement suggestions relative to an 80" door.
Frequently Asked Questions (FAQ)
1. Does it feature a dusk-to-dawn sensor?
Absolutely. This exterior light fixture boasts an intelligent dusk-to-dawn sensor that seamlessly transitions from off to on as nightfall approaches, automatically adjusting to ambient light levels below 20 LUX. In the morning, when brightness exceeds 90 LUX, it turns off, saving energy and eliminating the need for manual operation.
2. What could be the reason if the lamp does not turn on during installation?
If the lamp remains off during installation, it's most likely due to the dusk-to-dawn sensor's natural deactivation during daylight hours. To verify functionality, cover the sensor with your hand or a cloth after turning on the power switch. If the lamp illuminates, it confirms the lamp is working as intended, and the issue relates to the sensor's automatic day/night cycle.
3. What if I do not need the dusk-to-dawn functionality?
This fixture is designed with a convenient rubber cap that allows you to easily disable the dusk-to-dawn feature. Simply slide the cap over the sensor whenever you prefer manual control over the lamp's operation.
4. What should I do if the glass lampshade I received is cracked or broken?
If your glass lampshade is cracked, broken, or not in perfect condition, please contact customer service immediately. The team is dedicated to providing the best possible solution and ensuring your satisfaction.
Assembly & Installation Instructions
Dear Customer:
Thank you for choosing 4Modern Home! For questions or issues, contact us via email at support@4modernhome.com or by calling 469-312-6428. We are dedicated to ensuring your complete satisfaction and value your feedback.
Warning: If any special control devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electric contractor.
Warning: California Residents Proposition 65 This product contains lead, a chemical known to the state of California to cause cancer and birth defects or other reproductive harm. Do not place the product in your mouth. Wash your hands after handling this product.
Caution: It is highly recommended to get an electrician to install this light. Please ensure the electricity is turned off at the main circuit breaker before beginning installation. All glass is fragile. Use care when handling glass component(s) and/or lamp(s).
Diagram Description: A diagram illustrates sealing the gap between the fixture and the wall after securing it. It shows applying a bead of caulk to the top and sides using a caulking gun to create a seal.
Wire Connection Diagram
Wires meeting safety standards are required to connect the electrical circuit.
CAUTION: Risk of fire
Diagram Description: A wire connection diagram shows connections for Line (L), Neutral (N), and Ground wires.
Please read all instructions carefully. Before proceeding to install, ensure the power supply is turned off and remains off until installation is completed.
| Code | Part Description | QTY |
|---|---|---|
| A | Junction box | 0 |
| B | Wire caps | 3 |
| C | Mounting bracket | 1 |
| D | Mounting screws1 | 2 |
| E | Mounting screws2 | 2 |
| F | Lamp body | 1 |
| G | Light bulb | 0 |
7030-3BK Installation Steps
Diagram Description: A diagram illustrates the assembly process, showing the connection of the mounting bracket (C) to the junction box (A) with screws (D), wiring connections to the lamp body (F), and securing the lamp body with screws (E). A light bulb (G) is shown being installed.
- Unscrew screw E from the lamp body and remove the hanging plate C.
- Install the hanging plate C lock on the junction box A with screw D.
- With the terminal B, connect the black, white, ground wire and input line respectively with the lamp body.
- Lock the lamp body on the hanging plate C with screw E.
- Transfer the bulb G knob to the lamp body.
Installation completed.
