4Modern Home 7072-2BK Outdoor Wall Light

Product Overview

This document provides operational and installation instructions for the 4Modern Home 7072-2BK outdoor wall light fixture. This fixture is designed for exterior use and features an intelligent dusk-to-dawn sensor.

Model: 7072-2BK

Brand: 4modernhome

Manufactured in: CHINA

Key Features

Dusk-to-Dawn Sensor: The fixture is equipped with an intelligent dusk-to-dawn sensor that automatically turns the light on as nightfall approaches and off in the morning. It adjusts to ambient light levels, turning on below 20 LUX and off above 90 LUX, saving energy and eliminating manual operation.

Manual Control: For users who prefer manual control, a convenient rubber cap is included. Simply slide this cap over the sensor to disable the dusk-to-dawn feature.

Applicable Bulb Types: A60, T45, ST64.

Where to Place Your Outdoor Wall Lights

Proper placement ensures optimal illumination and functionality. The following guidelines are recommended:

• Single Light Placement: If installing one light next to an entryway or garage door, position it approximately 1/3 of the door's height from the ground. For example, on an 80-inch tall door, the light should be placed about 26.7 inches from the ground.
• Dual Light Placement: If installing lights on both sides of a door, position them approximately 1/4 of the door's height from the ground. For an 80-inch door, this would be 20 inches from the ground for each light.
• Illumination Height: Lights should ideally be placed around 66 inches from the floor or ground to properly illuminate the lock and handle area.
• Edge Clearance: Position lights at least 6 inches from the edge of the door.
• Single Light Side: If using only one light, place it on the side of the door closest to the door handle.

Diagram Description: An illustration shows a house exterior with dimensions indicating a 15.6" tall fixture, an 80" door, and recommended light placement at 60" height for each fixture when two are used on an 80" door (calculated as 80" * 0.75 = 60" for two lights, or 80"/4 = 20" from ground for placement height).

Troubleshooting and Support

Frequently Asked Questions:

1. Does it feature a dusk-to-dawn sensor?

   Yes, it features an intelligent dusk-to-dawn sensor that automatically adjusts to ambient light levels.

2. What could be the reason if the lamp does not turn on during installation?

   This is most likely due to the dusk-to-dawn sensor's natural deactivation during daylight hours. To test functionality, cover the sensor with your hand or a cloth after turning on the power switch. If the lamp illuminates, it confirms the sensor is working correctly and the issue relates to the automatic day/night cycle.

3. What if I do not need the dusk-to-dawn functionality?

   You can easily disable the dusk-to-dawn feature by sliding the provided rubber cap over the sensor for manual control.

4. What should I do if the glass lampshade I received is cracked or broken?

   We understand receiving a damaged product can be disappointing. If your glass lampshade is cracked, broken, or not in perfect condition, please contact us immediately. Our customer service team is dedicated to providing the best possible solution and ensuring your satisfaction.

Customer Service Contact:

For any questions or issues, please contact 4modernhome customer service:

• Email: support@4modernhome.com
• Phone: 469-312-6428

Your feedback is valued and helps future customers make informed decisions. Sharing your experience via a product review is encouraged.

Assembly & Installation Instructions

Important: Please read all instructions carefully before proceeding with installation. Ensure the power supply is turned off and remains off until installation is completed.

Warnings:

• If any special control devices are used with this fixture, follow their instructions carefully to ensure full compliance with N.E.C. requirements. Contact a qualified electrician if you have questions.
• California Residents Proposition 65: This product contains lead, a chemical known to the state of California to cause cancer and birth defects or other reproductive harm. Do not place the product in your mouth. Wash your hands after handling this product.

Caution:

• It is highly recommended to have an electrician install this light.
• Always turn off the electricity at the main circuit breaker before beginning installation.
• All glass components are fragile. Use care when handling glass parts and/or lamps.

Wire Connection Diagram:

Wires meeting safety standards are required to connect the electrical circuit.

CAUTION: ⚠️ Risk of fire.

The diagram shows terminals labeled 'L' (Line) and 'N' (Neutral) for connecting the electrical circuit.

Parts Included:

Installation Steps for 7072-2BK:

1. Unscrew screw G from the lamp body and remove lamp holder H.
2. Remove screw E from the lamp body and remove hanging plate B.
3. Use screw C to lock hanging board B onto junction box A.
4. Use terminal D to connect the wires: black (line), white (neutral), and ground wire separately.
5. Use screw E to lock the lamp body onto hanging plate B.
6. Attach the bulb (part I) to the lamp body.
7. Use screw G to secure the lamp body H to the assembly.

Installation is complete.

Diagram Description (Drawing 1):

After securing the fixture to the wall, it is recommended to seal the gap between the wall and the fixture backplate on the top and both sides using a good quality waterproof caulk or silicone sealant (not included). A bead of caulk is shown being applied.

Diagram Description (Wire Connection & Parts Assembly):

An exploded view diagram shows the assembly of parts labeled A through I. It illustrates how the mounting bracket (B) attaches to the junction box (A) using screws (C). Wires are connected via terminals (D). The lamp body (H) is attached to the mounting plate (B) using screws (E), and the bulb (I) is inserted. Screws (G) are used for final securing.