CASIO

Water Protection

For all watch categories, it is prohibited to:

• Press buttons underwater.
• Move hands underwater.
• Unscrew the crown underwater.

If the watch is exposed to saltwater, rinse it thoroughly and dry it. Do not wear watches with leather straps while swimming. Avoid prolonged contact of leather straps with water.

Watches are classified into levels (from I to V) according to their degree of water protection. Check your watch's level using the table below to determine its correct usage.

Notes:

• I: Watches are not protected from water. Avoid any moisture ingress.
• II: WR (Water Resistant) means the model is waterproof according to ISO 2281. Brief contact with water will not cause any problems.
• III: With 5 Bar (50 meters) water resistance, the watch can withstand the indicated water pressure and can therefore be used during showers and brief swimming.
• IV: 10 Bar (100 meters) water resistance means the watch can be used during normal swimming and snorkeling.
• V: 20 Bar (200 meters) water resistance means the watch can be used for scuba diving (except for depths requiring a helium-oxygen mixture).

When using the product in conditions of rapid temperature changes, slight condensation may form on the inside of the glass. This phenomenon is due to the laws of physics and is not a defect.

CASIO COMPUTER CO., LTD. is not responsible for any damage that may arise from the use of these watches, and does not accept any claims from third parties.

General Notes

Your watch may differ slightly from the illustrations in this manual.

Note on Screw-Lock Crown:

• Some water-resistant watch models are equipped with a screw-lock crown.
• To pull out such a crown, you must unlock it by turning it in the direction indicated in the illustration [circular arrow]. Do not use excessive force when pulling out the crown. This may cause damage.
• Note that the watch becomes unprotected from water and moisture when the crown is pulled out. After completing all operations using the crown, return it to its original position and lock it.

Setting the Current Time

Modules 1362, 1398, 1770, 2799, 3378, 4370

Pull out the crown. Rotate it to set the hands to the current time. Push the crown back to its original position.

Illustration shows a watch face with hands and a crown labeled 'Crown'.

Modules 705, 706, 1300, 1311, 1330, 1344, 1360, 1399, 1747, 1771, 1782, 4328, 4394, 4747, 5049, 5284, 5361, 5364, 5375, 5577

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time, advance the minute hand 4-5 minutes ahead of the current time, and then move it back.
3. At the time signal, close and secure the crown.

Illustrations show watch faces with crowns labeled 'Crown' and specific module numbers.

Modules 707, 708, 1331, 1332, 1335, 1336, 1342, 1345, 1346, 1369, 1370, 1373, 1701, 1710, 1711, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044, 5058, 5116, 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. To fine-tune the current time, move the minute hand back 4-5 minutes from the desired value, then return to the current value.
3. Push the crown back to its original position to resume time display.

Illustration shows a watch face with hands, a date display (e.g., '30'), and a crown with labels for 'First click: Date setting' and 'Second click: Time setting'.

Modules 709, 1309, 1333, 1334, 1347, 3716, 5125, 5167, 5223, 5237, 5249, 5339, 5373, 5458, 5474

Setting the Current Time

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Rotate the crown to set the hands to the current time. To fine-tune the current time, move the minute hand back 4-5 minutes from the desired value, then return to the current value.
3. Push the crown back to its original position to resume time display.

Illustrations show watch faces with crowns labeled 'Crown (normal position)' and 'First click: Date and day of week setting', 'Second click: Time setting'. Examples show 'SUN 30' and 'WED 30'.

Setting the Date and Day of the Week

To ensure the date and day of the week change at midnight, do not set them between 8:00 PM and 2:00 AM.

Modules 707, 708, 1331, 1332, 1335, 1336, 1342, 1345, 1346, 1369, 1370, 1373, 1701, 1710, 1711, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044, 5058, 5116, 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

1. Pull out the crown to the first click.
2. Rotate it to set the desired date.
3. Push the crown back to its original position.

Illustration shows a watch face with a date display (e.g., '30') and a crown with labels for 'First click: Date setting' and 'Second click: Time setting'.

Modules 709, 1309, 1333, 1334, 1347, 3716, 5125, 5167, 5223, 5237, 5249, 5339, 5373, 5458, 5474

1. Pull out the crown to the first click.
2. Set the date by rotating the crown counter-clockwise.
3. Set the day of the week by rotating the crown clockwise. Days of the week are indicated in English or Spanish.

4. Push the crown back to its original position.

Watches with Backlight

• Press and hold button L to illuminate the watch face.
• Depending on the watch model, the backlight duration is 2 to 3 seconds, 1 second, or until button L is held (Module 5577).
• Depending on the watch model, the backlight is provided by electroluminescent (EL) elements or LEDs. EL elements lose power after prolonged use.
• Frequent use of the backlight reduces battery life.
• Turning on the backlight for an extended period or when the battery is low may cause the watch hands to stop moving for a while.

Illustrations show watch faces with a crown labeled 'Crown' and a button labeled 'L (Backlight Button)'.

Watches with Rotating Bezel

Rotate the bezel to align the mark [triangle symbol] with the minute hand. After some time, you can tell how much time has passed since you aligned the mark with the minute hand.

Illustration shows a watch face with a rotating bezel, labeled 'Bezel for measuring elapsed time'.

Technical Specifications

Specifications are subject to change without prior notice.

Product Information

Product Name: Electronic / Electro-mechanical quartz wristwatches (men's/women's)

Brand: CASIO

Manufacturer: CASIO COMPUTER Co.,Ltd.

Manufacturer's Address: 1-6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Importer: OOO 'Casio', 127015, Russia, Moscow, Butyrskaya St., bld. 77

Warranty Period: 2 years

Address of authorized organization for claims: Indicated on the warranty card.