7052-1WH Operations Manual
Brand: 4ModernHome
Manufactured in: China
Where to Place Your Outdoor Wall Lights
Proper placement ensures optimal illumination and sensor function.
Single Light Placement: If installing one light next to an entryway or garage door, position it at 1/3 the height of the door. For example, on an 80-inch tall door, the light should be approximately 26.7 inches from the floor.
Dual Light Placement: If installing lights on both sides of the door, position each light at 1/4 the height of the door. For an 80-inch door, this would be approximately 20 inches from the floor.
Illumination Height: Lights should be placed 66 inches from the floor or ground to effectively illuminate the lock and handle area.
Edge Clearance: Position lights 6 inches from the edge of the door.
Single Light Orientation: If using only one light, place it on the side of the door closest to the door handle.
Diagram Description: An illustration shows a house with two wall lights mounted on either side of the front door. Key dimensions provided are: Fixture Height: 12.8 inches; Door Height: 80 inches; Recommended Fixture Height from Ground: 60 inches. The diagram also shows the 80" door height and a calculation for fixture height (80" door x 0.75 = 60" height for each fixture), implying a 1/4 placement ratio.
Helpful Tip: This fixture is equipped with a dusk-to-dawn sensor. Ensure no objects, such as eaves or overhangs, obstruct the sensor, as this could cause the light to remain on continuously.
Features and Frequently Asked Questions (FAQs)
Dusk-to-Dawn Sensor
Yes, the fixture features an intelligent dusk-to-dawn sensor. It automatically turns the light ON when ambient light levels fall below 20 LUX and OFF when brightness exceeds 90 LUX. This provides energy savings and eliminates the need for manual operation.
Troubleshooting: Lamp Not Turning On
If the lamp does not turn on during installation, it is likely due to the sensor's natural deactivation during daylight hours. To test functionality, cover the sensor with your hand or a cloth after turning on the power switch. If the lamp illuminates, the sensor is working correctly, and the issue is related to the automatic day/night cycle.
Disabling the Dusk-to-Dawn Functionality
If you prefer manual control, the fixture includes a convenient rubber cap. Simply slide this cap over the sensor to disable the dusk-to-dawn feature.
Damaged Glass Lampshade
If the glass lampshade is received cracked, broken, or not in perfect condition, please contact 4ModernHome customer service immediately for assistance.
Assembly & Installation Instructions
Thank you for choosing 4ModernHome. For any questions or issues, please contact customer support via email at support@4modernhome.com or by phone at 469-312-6428.
Your feedback is valued to help future customers.
Important Warnings and Cautions:
- NEC Compliance: If using special control devices, follow instructions carefully to ensure full compliance with National Electrical Code (NEC) requirements. Consult a qualified electrician for any questions.
- California Proposition 65: This product contains lead, a chemical known to the state of California to cause cancer, birth defects, or other reproductive harm. Do not place the product in your mouth. Wash hands thoroughly after handling.
- Installation Recommendation: It is highly recommended to have a qualified electrician perform the installation.
- Electrical Safety: Ensure the power supply is turned OFF at the main circuit breaker before beginning any installation work. Keep it OFF until installation is complete.
- Glass Handling: All glass components are fragile. Handle with care to prevent breakage.
Parts Included:
| Code | Part Description | QTY |
|---|---|---|
| A | Junction box | 0 |
| B | Mounting bracket | 1 |
| C | Mounting screws1 | 2 |
| D | Wire caps | 3 |
| E | Photoelectric switch | 1 |
| F | Lamp body | 1 |
| G | Mounting screws2 | 2 |
| H | Ring | 1 |
| I | Rubber mat | 1 |
| J | Light bulb | 0 |
Wiring Diagram:
Wires must meet safety standards for electrical circuit connection. CAUTION: Risk of fire. Ensure power is OFF before proceeding.
Diagram Description: A simplified wiring diagram shows connections for Line (L), Neutral (N), and Ground wires from the power source to the fixture's internal components.
Sealing Recommendation:
Diagram Description: After securing the fixture to the wall, it is recommended to seal the gap between the wall and the fixture backplate on the top and both sides using a high-quality waterproof caulk or silicone sealant (not included). This prevents moisture ingress.
Applicable Bulb Types:
A60, T45, ST64, and similar types.
Step-by-Step Installation Guide
Follow these steps for the installation of the 7052-1WH fixture:
- Turn the nut G from the lamp body and remove the hanging plate B.
- Secure the hanging plate B onto the junction box A using screw C.
- Attach the ring H with the silica gel pad I to the lamp body.
- Connect the lamp body wires (black, white, ground) to the corresponding input lines using terminal B.
- Secure the lamp body onto the hanging board B using the nut G.
- Install the light bulb J into the lamp body.
Installation is now completed.
Diagram Description: A detailed illustration visually guides the user through the assembly process, showing how parts A through J connect and are secured in sequence.
