HAGOR CPS Mobile Stand 2x 55-65" Installation Manual
Article Number: 3325
Safety Precautions
Technical devices are of considerable value. You should therefore handle the components carefully during installation and protect them if necessary. If necessary, the installation area should also be secured. Falling parts can cause injuries and material damage. The materials included in the scope of delivery may not be suitable for the special conditions at the installation site. Please check this in advance and replace it with suitable materials if necessary. If you are unsure about the installation of the product or have any questions, please contact HAGOR Products GmbH or other trained specialists.
Scope of Delivery
Main Components
- A: Vertical Support (2x)
- B: Base Support (2x)
- C: Caster Wheel (4x)
- D: Base Frame (1x)
- E: Horizontal Rail (2x)
- F: Cable Management Clip (16x)
- G: Base Connector (2x)
- H: Upper Rail (2x)
- J: Small Bracket (2x)
- K: Cable Clip (4x)
- L: Mounting Plate (3x)
- P: Bracket (2x)
- Q: VESA Mount (4x)
- R: Safety Pin (4x)
Hardware
- M8x90 Screw (8x)
- M8x10 Screw (2x)
- Fastener O (18x)
- Fastener M (12x)
- M5x14 Screw (M-A) (8x)
- M6x14 Screw (M-B) (8x)
- M6x30 Screw (M-C) (8x)
- M8x30 Screw (M-D) (8x)
- M8x50 Screw (M-E) (8x)
- Square Washer (M-F) (8x)
- Small Spacer (M-G) (16x)
- Large Spacer (M-H) (16x)
Installation Steps
Step 1
Attach vertical supports (A) to the base frame (E) using screws (B, M8x90).
Step 2
Attach caster wheels (C) to the base of the assembled structure.
Step 3
Insert fasteners (M) into the slots of the upper rails (H) and slide the upper rails onto the vertical supports (A).
Step 4
Attach bracket (P) to the horizontal rail (E) using screws (M8x12) and fasteners (O).
Step 5
Repeat Step 4 for the other side of the horizontal rail (E).
Step 6
Attach bracket (J) to the horizontal rail (E) using fasteners (N, M8x10).
Step 7
Attach base connector (G) to the upright structure (E).
Step 8
Attach VESA mounts (Q) to the uprights, ensuring the arrow points upwards [⬆️].
Step 9: Attach Display
Select appropriate screws (M-A to M-E), washers (M-F), and spacers (M-G, M-H) based on the screen's VESA pattern and depth. Center the VESA mounts (Q) on the back of the display and secure them. Avoid over-tightening screws to prevent damage. [✔️] Correct mounting example. [❌] Incorrect mounting example.
Step 10 & 11: Adjust Tilt
Adjust the tilt of the display as needed.
Step 12: Locking Mechanism
Adjust the tilt locking mechanism using a Phillips head screwdriver [➕].
Step 13: Angle Adjustment
The stand supports angle adjustments from 0° to -20°. The -20° position is the natural angle, making the safety pin (R) unnecessary.
Step 14: Install Cable Clips
Install cable clips (K) onto the stand.
Step 15: Install Cable Management
Install cable management clips (F). An optional cable routing solution is indicated.
Dimensions
| Overall Height (Max) | 1970 mm |
| Overall Height (Min) | 1820 mm |
| Overall Width | 2009 mm |
| Base Width | 1010 mm |
| Base Depth | 1500 mm |
| VESA Compatibility | Min 100 mm, Max 400 mm |
| Horizontal Rail Depth | 440 mm |
| Other Dimensions | 80 mm, 35 mm, 120 mm, 100 mm, 50 mm |
