STRONG SRT 8215 Digital Terrestrial HD Receiver

Introduction

This document provides installation instructions and user guidance for the STRONG SRT 8215 Digital Terrestrial HD Receiver. The original document includes installation instructions in multiple languages: English, German, French, Italian, Spanish, Portuguese, Swedish, Czech, Slovak, Croatian, Hungarian, and Dutch.

The receiver offers DVB-T2 High Definition reception with features such as USB recording, EPG, Teletext, Parental Control, and RSS Feeds.

Receiver Overview

Front Panel (Fig. 1)

The front panel features:

• IR Sensor: For receiving signals from the remote control.
• LED Display: Shows channel number and standby time.
• LED Indicator: Green indicates the receiver is on.
• Standby/Power Button: Turns the receiver on or puts it into standby mode.
• USB Port: For connecting USB storage devices.

Rear Panel (Fig. 2)

The rear panel includes:

• ANT IN: Connection for terrestrial antenna (IEC F connector).
• ETHERNET: RJ-45 port for network connection (e.g., for RSS feeds, weather).
• HDMI: For connecting to a TV or AV receiver with high-quality digital audio/video.
• AUDIO L/R: Analog audio output for connecting to amplifiers.
• TV SCART: For connecting to older TVs via SCART cable.
• Power Input (12V): For connecting the power adapter (100-240V AC ~ 50/60 Hz to 12V DC / 1A).

Remote Control (Fig. 3)

The remote control includes:

• Power/Standby button (1).
• Mute button (2).
• Number buttons (0-9) for direct channel access (3).
• FAV button for favorite channel groups (4).
• Navigation buttons (Up, Down, Left, Right) (8, 9).
• OK button for confirmation (10).
• INFO button for channel information (6).
• EPG button for Electronic Program Guide (7).
• MENU button to access the main menu (11).
• Other function buttons: Play/Pause (13), Fast Forward/Rewind (14), Record (15), Media Player (16), Multimedia skip (17), Stop (18), Colored buttons (19) for specific functions.

Battery Installation (Fig. 4)

To install batteries in the remote control:

1. Slide open the battery compartment cover.
2. Insert 2x AAA batteries, observing polarity.
3. Close the battery compartment cover.

Remote Control Usage (Fig. 5)

The remote control operates within a range of approximately 5 meters and an angle of up to 30 degrees. Ensure there are no obstructions between the remote and the receiver's IR sensor. Direct sunlight or bright lights may interfere with operation.

Connections

Refer to the diagrams (Fig. 6, 7, 8) for connection guidance.

3.1 Connecting to a Terrestrial Antenna

Connect your terrestrial antenna (indoor or outdoor) to the ANT IN port on the rear panel using a properly shielded antenna cable and connector.

Note: If indoor antenna signals are weak, consider using an outdoor antenna. If using an active antenna with a built-in amplifier, enable 'Antenna Power' in the receiver's menu.

3.2 Connecting to TV via HDMI Cable

Connect the receiver to your TV using a high-quality HDMI cable for the best audio and video quality.

3.3 Connecting to TV via SCART Cable

Connect the receiver to your TV using a SCART cable if your TV does not have an HDMI input or as an alternative connection.

3.4 Connecting a USB Mass Storage Device

The USB port supports devices like USB pendrives or external hard drives (up to 800mA). USB 2.0 or higher is recommended for optimal performance with video and HD playback.

3.5 Ethernet Connection for RSS Feeds and Weather

Connect the receiver to your router using an Ethernet (RJ-45) cable (CAT5E or higher) to access RSS feeds and weather forecasts.

3.6 Connecting to Main Power

Once all connections are made, plug the receiver into a mains power outlet using the provided power adapter.

3.7 Further Connections for Enhanced Entertainment

Connect the receiver's HDMI output to a digital audio amplifier or home cinema system for high-quality surround sound. Then, connect the amplifier's HDMI output to the TV.

First-Time Setup (Section 4.0)

Upon first power-on, you will be guided through initial setup. This includes selecting:

• Region: Choose your geographical region. This affects channel tuning and numbering (LCN). Selecting 'Other' allows manual channel sorting.
• Language: Set the menu and audio language.
• Antenna Power: Enable if using an active antenna.
• Scan Mode: Choose 'All' for all channels (free and encrypted) or 'Free' for only free-to-air channels.

Use the navigation buttons (▲▼◄►) to select options and OK to confirm. After setting preferences, select 'Search' and press OK to scan for channels.

Note: Incorrect region selection may lead to missing channels or incorrect channel placement. Encrypted channels may not be viewable on this model.

Tip: If the 'Welcome' menu does not appear, perform a factory reset via MENU > Settings > Tools > Factory Settings (default PIN: 0000).

Operation

6.1 Channel Changing

Channels can be changed via:

• Direct input using the number buttons (0-9).
• Channel list accessed via the OK button.
• Previous/Next channel buttons (▲▼).

6.2 Information Banner

Press INFO to display current channel and program information. Pressing INFO twice shows technical details like signal strength and quality.

6.3 Audio Language Selection

For channels with multiple audio streams, press AUDIO to select your preferred language.

6.4 Teletext

Access Teletext by pressing TTX. Use number buttons to select pages, and navigation buttons to move between pages or subpages.

6.5 Subtitles

Press SUBTITLE to view available subtitle languages for a channel.

6.6 EPG (Electronic Program Guide)

Press EPG to access the program guide. Use navigation buttons to browse channels and events. Press OK to view event details. Colored buttons can be used to set reminders or record programs.

6.7 Recording, Timeshift, and Formatting

Requires a USB storage device formatted as FAT32.

• Instant Recording: Press the record button (4) to start recording. Press stop (3) to end.
• Timeshift: Press the pause button (2) during playback to pause live TV. Press again to resume. Use playback controls (5, 6) for navigation. Press stop (3) to exit Timeshift mode.
• Timer Recording: Programs can be scheduled for recording via the EPG or the Timer menu. Up to 8 timers can be set.
• Playback: Recorded programs are found in the 'ALIDVRS2' folder on the USB device. Access via MENU > Media Player.

Main Menu (Section 7.0)

The main menu provides access to:

• Installation (7.1): Channel scanning (manual, auto, country settings, antenna power, scan mode).
• Channel Editing (7.2): Managing favorite lists, reordering, locking, and deleting channels.
• Settings (7.3): Language, TV system (resolution, aspect ratio, audio output), display settings, time settings, timer setup, parental lock, OSD settings.
• Media Player (7.4): Playback of video, music, and photo files from USB. Includes PVR information and USB formatting tools.
• Tools (7.5): System information, factory reset, network settings (DHCP, IP), RSS feed selection, weather forecast, and USB software updates.

Troubleshooting

If your receiver is not functioning correctly, consult the following:

No Power / Display

Problem: LED indicator and LCD display do not turn on.

Possible Cause: Power cord disconnected; power adapter not connected or 12V plug improperly inserted.

Solution: Check adapter connection to mains and ensure it has power. Verify the 12V plug is securely inserted into the receiver.

No Signal

Problem: No signal.

Possible Cause: Antenna disconnected, damaged, or not properly connected; signal area issues; active antenna requires power; external power needed.

Solution: Check antenna cable and connections. Consult seller for antenna advice. Enable antenna power in receiver settings if applicable. Check for external power requirements.

No Picture or Sound

Problem: No picture or sound on TV/receiver.

Possible Cause: HDMI or SCART input not selected on TV; TV resolution too high for receiver; TV/receiver not powered on.

Solution: Select correct TV input. Try a lower resolution on the receiver. Ensure TV and receiver are powered on.

Message: Channel is Encrypted

Problem: Channel is encrypted.

Solution: Select a different channel. This model may not support encrypted channels.

No Remote Control Response

Problem: Remote control is unresponsive.

Possible Cause: Receiver in standby; remote not aimed correctly; front panel locked; remote batteries depleted.

Solution: Ensure receiver is on. Aim remote directly at the receiver. Check for front panel lock. Replace remote batteries.

Forgot PIN / Channel Lock Code

Problem: Forgotten PIN or channel lock code.

Solution: Default PIN is 0000. Contact STRONG support if you cannot reset it.

Cannot Receive Digital Signal in New Location

Problem: Poor or no digital reception after moving the receiver.

Possible Cause: Weak antenna signal; indoor antenna signal strength lower than outdoor; active antenna requires power.

Solution: Press INFO three times to display signal strength bars and adjust antenna. Rescan channels. Check active antenna power. Consider using an outdoor antenna.

Receiver Turns Off Automatically

Problem: Receiver turns off automatically.

Possible Cause: Auto Standby function is enabled.

Solution: Disable Auto Standby in settings (Section 7.3.9).

Video Playback Issues (Freezing, Artifacts)

Problem: Video playback (or Timeshift) freezes or shows artifacts, especially with HD content.

Possible Cause: USB device read/write speed is too low.

Solution: Ensure the USB storage device has sufficient space and a high enough write speed. Some pendrives may not meet the required speed.

Technical Specifications

Tuner

• Input Connector: IEC60169-2, female, 75 Ohm nominal
• Input Frequency Range: VHF: 174~230 MHz, UHF: 474~790 MHz
• Input Signal Level: DVB-T2: -70 dBm ~ -25 dBm
• Antenna Power: 5 V DC, max. 50 mA, short-circuit protected

Demodulator

• Demodulator: QPSK, 16/64/128/256 QAM
• Transmission Mode: DVB-T2 (EN 302 755)
• Guard Intervals: Normal & Extended; DVB-T2 = 1/128, 1/32, 1/16, 19/256, 1/8, 19/128, 1/4

Video Decoder

• Video Resolutions: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
• Decoding & Video Output: MPEG 2/4 H.264/H.265 (HEVC) - HD / PAL
• Aspect Ratio: 4:3, 16:9
• Conversion: Letterbox, Pan & Scan, Full screen, Ignore.

Audio Decoder

• Audio Support: MPEG-4 Profile Level 4, Dolby Digital Plus*/AC3+/PCM, MPEG MusiCam Layer II
• Bitrate: 32, 44.1, 48 KHz
• Audio Mode: Stereo, Mono

*Dolby Digital Plus, Dolby Digital and the double-D symbol are registered trademarks of Dolby Laboratories.

Multimedia

• Video Playback: MPEG, FLV, TS, MPEG-4, H.265/HEVC*
• Audio Playback: MP3, FLAC, OGG*
• Image Preview: BMP, JPG*

*STRONG cannot guarantee playback of all files due to codec, bitrate, and resolution dependencies.

Connectors

• ANT IN - IEC F
• TV SCART (CVBS, Audio L/R)
• AUDIO L/R
• HDMI
• RJ-45 Ethernet
• Power Switch
• USB 2.0 port: 5 V/500 mA (peak)

General Data

• Power Supply: AC 100-240 V ~ 50/60 Hz
• Input Voltage: DC 12 V, 1.0 A
• Power Consumption: 7 W (typ.), 12 W (max)
• Standby Power Consumption: max. 1.0 W
• Operating Temperature: 0°C ~ +40 °C
• Storage Temperature: -10 °C ~ +50 °C
• Operating Humidity: 10~85% RH, non-condensing
• Dimensions (WxDxH): 175 x 100 x 42 mm
• Weight: 0.26 kg

Warranty Information

The product comes with a 24-month warranty from the date of purchase.

Warranty does not apply in cases of:

• Improper handling or use contrary to intended purpose.
• Damage caused by third parties or force majeure.
• Unauthorized modifications.
• Installation of unauthorized software.
• Improper installation of STRONG software.
• Damage during transport.
• Mechanical damage or liquid ingress.

For warranty claims, please contact the STRONG hotline at 801 702 017 and have your purchase document, model, and serial number ready. Ensure the warranty card is filled out correctly. Return the product in its original packaging or equivalent.

Paid repairs may be offered for issues not covered by warranty.

Contact Information for Service Center Polska:

STRONG Service Center Polska
c/o RAGZ Sp. z o.o.
Al. Piłsudskiego 143
92-236 ŁÓDŹ
POLSKA

Important: Warranty is valid only with a completed warranty card and proof of purchase (receipt or VAT invoice). The sender is responsible for ensuring the product is securely packaged for transport.