ZEGRAD RGB GAMING DESK

Components

Please check you have all the pieces listed below:

• M4x14 (Kx36): Image shows a small screw with a Phillips head.
• M8x16 (Lx8): Image shows a medium-sized bolt with a hexagonal head.
• M8 (Mx2): Image shows a larger bolt with a hexagonal head.
• Nx4: Image shows a small bolt with a hexagonal head.
• 6mm (Ox1): Image shows a flat washer.
• Desk Legs (Ax2): Image shows two identical, large, Z-shaped metal leg frames.
• Crossbars (C1x1, C2x1): Image shows two different metal crossbars used for structural support.
• Support Beams (Bx2): Image shows two identical, long, flat metal support beams.
• Tabletop (Dx1): Image shows the rectangular tabletop surface.
• Cable Management Clips (Ex1, Fx1): Images show plastic clips designed for cable management.
• RGB Controller/Strip Mount (Gx1): Image shows a ribbed plastic component, likely a mount for the RGB controller or LED strip.
• Desk Feet/Levelers (H1, H2): Images show two types of adjustable feet or levelers.
• Mounting Brackets (Ix2): Images show metal mounting brackets.
• Small Connectors (J1, J2): Images show small metal connecting pieces.

Installation Guide

Step 01

Attach the Support Beams (B) to the Desk Legs (A) using the M8x16 screws (L). Ensure the legs are oriented correctly. A warning ⚠️ indicates that screws need to be checked and tightened again after the whole desk is finished.

[Diagram shows two leg frames (A) being positioned, and two support beams (B) being attached horizontally between them using M8x16 screws (L).]

Step 02

Connect the Crossbars (C1, C2) between the two leg assemblies. Use M8x16 screws (L) and M8 bolts (M) as indicated. The diagram shows C1 and C2 being attached to the legs (A) and potentially the crossbars (B) using screws (L) and bolts (M).

[Diagram shows the two leg assemblies now connected by crossbars C1 and C2, using screws L and bolts M.]

Step 03

Place the Tabletop (D) upside down. Attach the assembled leg frame to the underside of the tabletop using M4x14 screws (Kx16).

[Diagram shows the tabletop (D) upside down. The assembled leg frame is placed on top of it, and M4x14 screws (Kx16) are used to secure the frame to pre-drilled holes on the underside of the tabletop.]

Step 04

Attach the Cable Management Clips (E) and (F) to the leg frame using the provided screws (Nx4 and Kx2). The diagram shows clips (E) being attached to the legs and a component (F) being attached to the frame. Also shows adjustable feet (N) being screwed into the bottom of the legs.

[Diagram shows the desk upright. Adjustable feet (N) are screwed into the bottom of the leg frames. Cable management clips (E) are attached to the inner sides of the leg frames, and a component (F) is attached to the rear support beam using screws (Nx4 and Kx2).]

Step 05

Install the small connectors (J1, J2) onto the frame using M4x14 screws (Kx4). These likely secure additional components or structural elements.

[Diagram shows small metal connectors (J1, J2) being attached to the underside of the desk frame using M4x14 screws (Kx4).]

Step 06

Attach the Desk Feet/Levelers (H1, H2) to the bottom of the leg assemblies using M4x14 screws (Kx3). The diagram shows H1 and H2 being secured to the legs.

[Diagram shows desk feet/levelers (H1, H2) being attached to the bottom of the leg assemblies using M4x14 screws (Kx3).]

Step 07

Mount the RGB Controller/Strip Mount (G) onto the underside of the desk using M4x14 screws (Kx2). The diagram shows component G being attached to the frame.

[Diagram shows the ribbed plastic mount (G) being attached to the underside of the desk frame using M4x14 screws (Kx2).]

Step 08

Attach the Mounting Brackets (I) to the desk legs. The diagram shows brackets (I) being attached to the lower part of the legs.

[Diagram shows metal mounting brackets (I) being attached to the desk legs.]

Step 09 & 10

The final assembly steps involve attaching components and managing cables. The diagram shows the complete desk with various parts attached and cable management features highlighted. Specific parts like Ax1, Bx1, Cx1, Dx7, Ex1, Fx8, Gx3 are shown in detail, along with connection points [item 09] and [item 10] which are likely for power or RGB connections.

[Diagram shows the fully assembled desk with various components attached and cable management features highlighted. Specific parts like Ax1, Bx1, Cx1, Dx7, Ex1, Fx8, Gx3 are detailed, along with connection points 09 and 10.]

Service & Support

For any questions or support, contact the NITHO Team at support@nitho.com or visit the website www.nitho.com.

Company: NITHO GmbH - Victoriastrasse 3b - 86150 Augsburg - Germany

Contact Email: SUPPORT@NITHO.COM

Website: WWW.NITHO.COM

Social Media: NITHOGAMES (Instagram), NITHOGAMES (Facebook)