TK001 Keypad Digital Deadbolt

User Guide

• At a Glance
• How to Use
• Definitions
• Code Format

Installation Instructions

• Installation Overview
• STEP 1: Prepare the door and check dimensions
• STEP 2: Install the latch and strike
• STEP 3: Install exterior assembly
• STEP 4: Install interior assembly
• STEP 5: Detect left/right hand door installation
• Quick Set Up
• Factory Default Settings
• Troubleshooting

At a Glance

How to Use

Unlock the door from outside

1. Enter Master/User code
2. Press the TEEHO button

Lock the door from outside

Auto Lock Mode

The bolt will extend automatically in 30 seconds after unlocking.

Manual Mode

Press any key on the keypad for 2 seconds.

Unlock the door from inside

Rotate the thumb turn to the Unlock position.

Lock the door from inside

Auto Lock Mode

The device will be locked automatically.

Manual Mode

Rotate the thumb turn to the Lock Position.

Definitions

• Master Code: Required for programming and feature settings. Can be used to unlock the door under vacation mode. The default master code must be changed before programming. Property owner & manager should keep this information confidential.
• Auto Lock: Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. The Auto Lock time delay can be customized between 10 and 99 seconds.
• Key Unlock: Always available when batteries are dead or user codes are forgotten.
• Low Battery Indicator: 10 beeps with 10 red light flashes after pressing any key to lock or unlock indicates the need for battery replacement. Replace with 4 brand new AA alkaline batteries. Do not mix used and new batteries. All settings are stored when batteries are removed and replaced.
• Wrong Entry Limit: After 10 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 3 minutes.
• Silent Mode: Mutes beep sounds when pressing the keypad, but low battery and system alerts are still audible.
• Vacation Mode: A security feature for when leaving home for vacation or a long trip. Enabling vacation mode restricts all user codes until the master code is entered. If the lock is unlocked by the thumb turn from the inside, an alarm will sound.
• One Time User Code: Can be used only once and is automatically deleted after use.
• Unlock with Fake code: Prevents pin code exposure by entering random digits before or after the pin code. Example: 83618 137192 14710.

Code Format

1. Master Code: 4 to 10 digits. The default Master Code is 12345678. Change it before programming.
2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code can be programmed.
3. Invalid Combinations: Master Code and User Code do not support the following:
   • Forward number sequence (e.g., 12345678)
   • Backward number sequence (e.g., 98765432)
   • Repeat number sequence (e.g., 22222222)
   • Containing existing code sequence (e.g., if 5683 is a code, then 568391 is invalid)

Installation Overview

Parts List:

• A: Backup key x2
• B: Exterior Assembly x1
• C: Latch x1
• D: Strike x1
• D-1: Reinforcement Plate x1 (optional)
• E: Mounting Plate x1
• F: Interior Assembly x1
• G: Battery Cover x1
• H: Strike Screws x2
• I: Latch Screws x2
• J: Mounting plate Screws x2
• K: Interior Assembly Screws x3
• L: Reset Tool x1
• M: Drive-In Collar (Optional)

If any parts are missing or damaged, please contact Customer Support.

STEP 1: Prepare the door and check dimensions

• A: Measure the hole in the door: 2-1/8" (54mm). Measure the hole in the door edge: 1" (25mm).
• B: Measure the backset: 2-3/8" or 2-3/4" (60mm or 70mm).
• C: Measure door thickness: 1-3/8" to 2" (35mm to 50mm).
• D: Ensure the hole in the door frame is drilled a minimum of 1" (25mm) deep.

STEP 2: Install the latch and strike

• A: Determine backset and adjust the latch:
  • Hold the latch in front of the door hole. If the slotted hole is centered, proceed to the next step.
  • If the slotted hole is not centered, rotate and pull the latch to extend it.
• B: Install the latch: Insert the latch into the door hole and secure with Latch Screws (I). If needed, use the Drive-In Collar (M).
• C: Test the deadbolt: Use a screwdriver to ensure the deadbolt works smoothly.
• D: Install strike on the door frame: Ensure the hole in the door frame is at least 1" (25mm) deep. Secure the strike with Strike Screws (H). Use the Reinforcement Plate (D-1) if necessary.

STEP 3: Install exterior assembly

• IMPORTANT: Before installation, ensure the latch is fully retracted (unlocked position).
• A: With the latch retracted, route the cable below the latch and insert the torque blade through the slot in the latch.
• B: Secure the mounting plate with the supplied screws (J). Keep parallel to the door edge. Do not overtighten screws.

STEP 4: Install interior assembly

• A: Push the battery cover outwards.
• B: Insert the cable connector to the socket and push firmly until completely attached.
• C: Keep the thumb turn in a vertical position and install the interior assembly.
• D: Attach the Interior Assembly to the Mounting Plate and tighten the Interior Assembly Screws (K).

STEP 5: Detect left/right hand door installation

• IMPORTANT: This step is required and crucial for the lock to operate properly. Reset the lock to teach it the door orientation.
• A: While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment. Use new, non-rechargeable Alkaline batteries only.
• B: Press and hold the Reset button on the interior assembly using the reset tool.
• C: Load the 4th battery and continue holding the reset button for 3 seconds, until you hear a "beep". The latch bolt will extend to learn the door orientation automatically.

Quick Set Up

• Change Master Code: TEEHO + Master Code + TEEHO > Press 1 > New Master Code + TEEHO > New Master Code + TEEHO (Succeed).
• Add User Code: TEEHO + Master Code + TEEHO > Press 2 > New User Code + TEEHO > New User Code + TEEHO (Succeed).
• Delete User Code: TEEHO + Master Code + TEEHO > Press 3 > Unwanted User Code + TEEHO (Succeed).
• Silent Mode: TEEHO + Master Code + TEEHO > Press 4 > 1 + TEEHO (Disabled) or 2 + TEEHO (Enabled).
• Auto Lock: TEEHO + Master Code + TEEHO > Press 5 > 1 + TEEHO (Enabled) or 2 + TEEHO (Disabled).
• Set Auto Lock Time: TEEHO + Master Code + TEEHO > Press 8 > Enter New Duration Time (10-99s) + TEEHO (Succeed).
• Add One-Time Code: TEEHO + Master Code + TEEHO > Press 7 > New User Code + TEEHO > New User Code + TEEHO (Succeed).
• Enable Vacation mode: TEEHO + Master Code + TEEHO > Press 6 > Press TEEHO (Vacation Mode Enabled).
• Disable Vacation mode: Master Code + TEEHO (Vacation Mode Disabled, The door was opened).

Factory Default Settings

How to Reset?

• IMPORTANT: Resetting will delete all User Codes stored in the lock.
• Step 1: Keep the door open and unlocked.
• Step 2: Press and hold the Reset button, simultaneously remove and replace one battery.
• Step 3: Continue holding the Reset button for 3 seconds until a "beep" is heard and the latch extends automatically.

Troubleshooting

• Why does not the latch extend but the motor is rotating when resetting my lock?

  Improper installation may be the cause. Review:

  1. Ensure the latch and strike are aligned.
  2. Slightly loosen mounting screws on the external assembly keypad and latch bolt if over-tightened.
  3. Open the door and reset the lock.
• Why does not the latch extend and the motor isn't rotating when resetting my lock?

  The deadbolt latch should be retracted (unlocked) throughout installation. The thumb turn should be vertical during installation steps 4C and 5A. Open the door and reset the lock.

• When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?

  This happens when the latch and strike are misaligned. Ensure the bolt hole on the door frame is at least 1 inch deep for full bolt extension. Check that the door closes properly and the deadbolt aligns with the strike or door frame hole without obstruction.

• Why does my lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?

  Re-install the lock. Ensure the lock is in the unlocked status during installation. Verify the thumb turn is vertical. Do not insert the backup key during installation.

• What does 5 short and fast beeps mean while programming?

  This indicates a timeout or wrong entry. Complete each setting step within 5 seconds. Change the default master code during the first programming. Ensure the user code is in the correct format (4 to 10 digits).

• What if I forget my Master Codes?

  Resetting the lock will restore the original master code (12345678) and erase all previous user codes.

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock's interior assembly and routinely check settings for unauthorized alterations.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care should be taken for a long-lasting finish. Use a soft, damp cloth for cleaning. Avoid lacquer thinner, caustic soaps, abrasive cleaners, or polishes, as they can damage the coating and cause tarnishing.
• The lock is water-resistant and can withstand splashes, but do not allow water or liquids to enter the lock.
• Avoid direct sunlight exposure, as long-term exposure may damage the lock.

Handleset Installation Instructions

Parts list:

• A: Handleset x1
• B: Latch x1
• C: Strike x1
• D: Dust Cover x1 (optional)
• E: Handle Lever x1
• F: Handle Lever & Handleset screws x3
• G: Latch & Strike screws x4
• H: Spacer x1

TOOL REQUIRED: Do not use an electric screwdriver during installation.

1. Prepare the door and check dimensions

• Ensure the hole in the door frame is drilled a minimum of 1/2" (12.7mm) deep for the latch to extend.
• Check door dimensions: Hole diameter 2-1/8" (54mm), Door thickness 1-3/8" to 2" (35mm to 50mm), Backset 2-3/8" or 2-3/4" (60mm or 70mm).

2. Latch backset adjustment

• The latch is adjustable for 2-3/8" (60mm) or 2-3/4" (70mm) backsets. Adjust if necessary.

3. Install latch and strike

• Ensure the latch is aligned with the chiseled hole.
• Ensure the hole in the door frame is a minimum of 1/2" (12.7mm) deep.

4. Install Handleset

• Ensure the base of the spindle is aligned to the hole.

5. Install Handle Lever

• Do not press the knob during handle installation.

Test the Handleset after installation: Keep the door open, retract the latch by pressing the knob from outside and pushing the lever from inside to test smooth operation.