ÄLSKVÄRD Changing Table/Chest of Drawers

Important Safety Information

⚠️ WARNING: Children have died from furniture tip-over. To reduce the risk of furniture tip-over:

• ALWAYS install the anti-tip device provided.
• NEVER put a TV on this product.
• NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• Place heaviest items in the lowest drawers.

Read and follow each step of the instructions carefully.

Tools Required

The following tools are typically needed for assembly:

• Screwdrivers (Phillips and flathead)
• Hammer
• Drill
• Drill bits (Ø 8 mm / 5/16" and Ø 3 mm / 1/8")

Wall Mounting

For safety, it is crucial to secure the furniture to the wall using the provided anti-tip hardware. The supplied screws and plugs are suitable for most solid (A) and hollow (B) walls. For solid wood, use screws without plugs (C). If unsure, seek professional advice.

Wall Mounting Options:

• A (Hollow Walls): Requires Ø 8 mm (5/16") drill bit, plug, and screw (approx. 70 mm / 2 3/4" length).
• B (Solid Walls): Requires Ø 8 mm (5/16") drill bit and screw (approx. 30 mm / 1 1/4" length).
• C (Solid Wood): Requires Ø 3 mm (1/8") drill bit and screw (approx. 30 mm / 1 1/4" length).

The wall bracket (part 114664) is used to secure the unit. Follow specific instructions for its assembly and attachment.

Parts List

Identify all parts before beginning assembly. Quantities are indicated.

Assembly Steps

Step 1

Attach the feet (153549, 4x) to the bottom of the main frame side panels. Insert dowels (101350, 8x) into the side panels.

Step 2

Attach the base panel (10081254, 1x) to the side panels using cam lock screws (102509, 6x) and cam locks (119030, 6x).

Step 3

Attach the lower back panels (10080997, 2x) to the frame using screws (100514, 6x).

Step 4

Attach the drawer runners (150497, 2x and 10043622, 2x) to the inside of the main frame using screws (100355, 8x).

Step 5

Insert cam lock screws (102509, 8x) into the side panels of the main frame. Attach the top panels (10081231, 2x) using cam locks (119030, 8x).

Step 6

Attach the upper back panel (10081254, 1x) to the frame using screws (100211, 6x).

Step 7

Attach the drawer runners (10101068, 2x and 10092907, 1x) to the main frame using screws (100355, 6x).

Step 8

Assemble the drawer boxes. Attach drawer sides (10081231, 2x and 10080997, 2x) to drawer bases (10081254, 1x and 10081007, 1x) using cam lock screws (151931, 12x) and cam locks (119030, 16x).

Step 9

Insert cam lock screws (118331, 12x) into the drawer side panels. Attach the drawer front panels using cam locks (119030, 12x).

Step 10

Attach drawer runners to the assembled drawer boxes using screws (101350, 4x).

Step 11

Attach the drawer runners to the drawer boxes using screws (114727, 4x) and cam locks (10092907, 3x).

Step 12

Slide the drawer bases into the frame. Secure the drawer sides to the frame using cam lock screws (102509, 2x) and cam locks (100092, 2x).

Step 13

Continue assembling drawers. Attach drawer sides to drawer bases using cam lock screws (102509, 2x) and cam locks (100092, 2x).

Step 14

Attach drawer runners to the drawer boxes using screws (100092, 2x) and dowels (100211, 2x).

Step 15

Attach drawer runners to the drawer boxes using cam lock screws (102509, 2x) and cam locks (100092, 2x).

Step 16

Attach the top frame rails to the main structure using cam lock screws (102509, 6x) and cam locks (100092, 6x).

Step 17

Attach the side panels of the changing top to the main frame using screws (100514, 2x) and dowels (120208, 2x).

Step 18

Attach the top support rails to the main structure using screws (100514, 2x) and dowels (120208, 2x).

Step 19

Assemble the drawer fronts. Attach drawer sides to drawer bases using screws (100514, 2x) and dowels (120208, 2x).

Step 20

Attach drawer runners to the drawer boxes using screws (130449, 2x) and dowels (10080997, 2x).

Step 21

Attach the side panels to the base panel using screws (10080997, 2x) and cam lock nuts (119030, 4x).

Step 22

Slide the back panel (10081254, 1x) into the grooves of the assembled frame.

Step 23

Attach the side panels to the base panel using screws (10081231, 1x) and cam lock nuts (10081254, 1x).

Step 24

Secure the side panels to the base using screws (145718, 4x).

Step 25

Secure the side panels to the base using cam lock screws (119030, 4x).

Step 26

Attach drawer runners to the drawer sides using cam lock screws (146114, 6x) and cam locks (10043622, 6x).

Step 27

Attach the drawer support rail using screw (100359, 1x) and dowel (150497, 1x).

Step 28

Attach the drawer support rail using screw (100359, 1x) and dowel (10085280, 1x).

Step 29

Attach the drawer front to the drawer box using screw (119976, 1x) and cam lock (10085280, 1x).

Step 30

Insert the assembled drawers into the frame.

Step 31

Attach the side panels of the changing top to the main frame using screws (100355, 2x).

Step 32

Attach the changing top to the main unit. This step involves securing the changing top, likely using cam lock screws (102509, 8x) and cam locks (100355, 6x) based on later steps.

Step 33

This step shows the attachment of the changing top, possibly securing it with screws.

Step 34

Attach the wall bracket components (114664, 2x) to the unit using screws (126916, 2x) and (147968, 2x).

Step 35

Attach the drawer knobs (10005905, 2x) to the drawer fronts.

Step 36

Assemble drawer components using screws (102509, 4x) and dowels (106940, 4x).

Step 37

Assemble drawer components using screws (102509, 4x) and cam locks (101350, 4x).

Step 38

Assemble drawer components using screws (101350, 2x) and dowels (101350, 2x).

Step 39

Connect drawer components.

Step 40

Assemble drawer components using screws (102509, 4x) and cam locks (102509, 4x).

Step 41

Assemble drawer components using screws (100092, 6x) and dowels (101350, 6x).

Step 42

Attach drawer runners to the assembled unit using screws (100092, 10x) and dowels (100211, 10x).

Step 43

Attach the changing top to the unit. Insert the changing top into place and secure it.

Step 44

Secure the unit to the wall using the anti-tip hardware. Attach the wall bracket (part 100355, 8x) and use screws (100355, 6x).

Final Checks

Ensure all screws are tightened and the unit is stable. If the unit is not secured to the wall, it poses a tip-over risk.