JBC FAE022 Flexible Arm

Product Reference

FAE022 Flexible Arm

• Total length (tube compressed): 1.20 m / 47.24 in
• Max. operating distance: 1.00 m / 39.37 in

Packing List

The following items are included:

• Flexible Arm (1 unit)
• Screws DIN7982 - Ø3.5x25 - black burnished (3 units) Ref. 0019142
• Manual Ref. 0035573 (1 unit)

Assembly Example

FAE 022 Flexible Arm Ø 50 mm: Bear in mind the installation dimensions (see page 5).

FAE010 Flexible Hose Ø 50 mm: Total length: ~1.6 m / ~63 in. Connect the flexible hose to the flexible arm.

FAE2 Fume Extractor: Fix the flange on your workbench with the supplied screws (more information on page 6).

How to Use

Arm Installation

Important Notes:

• Do not install the flexible arm on shelves or higher levels than the work bench. Forced bending radii can cause the arm to break.
• To avoid breaking the arm, do not extend the arm more than 100 cm / 39.37 in from the center of its base and do not go below the minimum bend radius of 20 cm / 7.87 in.

Arm Positioning

Thanks to the flexibility of the arm, its position can be adapted to the particular working environment and conditions.

The arm can be used in an upright position with the nozzle hanging over the workplace, or with the nozzle resting on the workbench.

Windings Compression

Note: In case of breakage, the windings can be plugged back into each other.

To plug the windings back in, align them with each other and firmly push them together.

If the flexible arm loses firmness, it must be re-compressed. To increase compression, turn the arm slightly clockwise. Once the arm is compressed, readjust its position.

Nozzle Replacement

The nozzle and tube are connected to each other by means of a bayonet lock. This makes it easy to replace the nozzles.

To Disassemble: Hold the tube with one hand. With the other hand, turn the nozzle counter-clockwise and pull it out.

To Install: Turn the new nozzle bayonet clockwise to lock it in place.

Dimensions Scheme for FAE022 Fixing

To assemble the flexible arm FAE020 (Ø50) for the first time, follow these instructions:

1. First, make the large central hole in your workbench as shown in the drawing below.
2. Place the FAE020 flange in the opening and mark the points for the three pilot holes.
3. Take out the flange and drill the three holes at the marked spots. See the hole diameter on the dimension scheme:

Workbench Hole Specifications:

• Drilled central hole: Ø 58 mm / 2.283 in
• Pilot holes (3x): max. Ø 2 mm / 0.079 in
• Distance between pilot holes: ~Ø74 mm / ~2.913 in

Specifications

FAE022 Flexible Arm

• Ref. FAE022
• Inner Tube Diameter: Ø50 mm / 1.97 in
• Total length (tube compressed): 1.20 m / 47.24 in
• Max. operating distance: 1.00 m / 39.37 in
• Total Net Weight: 1.65 kg / 3.64 lb
• Package Dimensions / Weight (L x W x H): 110 x 435 x 605 mm / 2.4 kg (4.33 x 17.13 x 23.82 in / 5.29 lb)
• Complies with CE standards.
• ESD safe.

Warranty

JBC's 2-year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labor. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.

End of Life Disposal

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

CE ♻️ Ⓔ