FIRSTECH CM7000 Remote Start Plus Security Controller Brain
FTI-STK1: Vehicle Coverage and Preparation Notes
| Make | Model | Year | Install | CAN | IMMO | BCM | Clutch | I/O Changes |
|---|---|---|---|---|---|---|---|---|
| DL-SUB9 | Subaru Ascent STD KEY AT (USA) | 2019-22 | Type 4 | 40-Pin | A | DSD | N/A | N/A |
Covered vehicles use BLADE-AL-SUB9 firmware and the following required accessories: Weblink Hub & ACC RFID1. Flash the module and update the controller firmware. Please follow the directions for RFID programming before attempting to program the BLADE module to the vehicle.
- CAN: Type 4 CAN connections are made using the 40-Pin BCM connector and require connecting the white 2-pin female connector to the black male 2-pin connector at marker [D] of the illustration.
- Immobilizer: Type A IMMO requires connecting the white male and female 2-pin connectors at marker [C] of the illustration.
- Lights: Parking lights are pre-wired in the FTI-STK1 harness. Replace the green/white wire of the CM I/O connector with the pre-terminated green/white wire of the harness.
- ACC-RFID1 (REQUIRED): SUB9 firmware does not provide immobilizer data; an ACC-RFID1 is therefore required for remote start.
- 2nd START: The FTI-STK1 harness is pre-wired with a red/black 2nd START output (not required in TYPE 2). Cut and insulate the provided wire to prevent short circuits when not used.
- I/O Changes: None required.
Advisory 1: Program ACC-RFID1 before attempting to program the BLADE module to the vehicle.
Advisory 2: Secure all 2-pin connections, both used and unused, to the main harness body.
FTI-STK1: Installation and Configuration Notes
- A: REQUIRED ACCESSORY
- B: ADAPTER NOT REQUIRED
- C: REQUIRED CONFIGURATION (TYPE A IMMO)
- D: REQUIRED CONNECTION
- E: NO CONNECTION
Feature Coverage
| IMMOBILIZER DATA | ARM OEM ALARM | DISARM OEM ALARM | DOOR LOCK | DOOR UNLOCK | PRIORITY UNLOCK | TRUNK/HATCH RELEASE | TACH OUTPUT | DOOR STATUS | TRUNK STATUS | BRAKE STATUS | E-BRAKE STATUS | A/M ALRM CONTROL FROM OEM REMOTE | A/M RS CONTROL FROM OEM REMOTE | AUTOLIGHT CTRL |
Installation Diagram
The diagram illustrates the connections required for the FTI-STK1 – AL-SUB9 – Type 4 for the 2019-22 Subaru Ascent STD KEY AT (USA). It includes the ignition switch assembly and BCM/Fuse Box connections. A ground connection is required as noted in the illustration.
LED Programming Error Codes
- 1x RED = Unable to communicate with RFID or immobilizer data.
- 2x RED = No CAN activity. Check the CAN wire connections.
- 3x RED = No ignition detected. Check the ignition wire connection and CAN.
- 4x RED = Required ignition output diode not detected.
Install Guide
Cartridge Installation
- Slide cartridge into unit. Notice button under LED.
- Ready for Module Programming Procedure.
Module Programming Procedure
- For this installation, the Weblink HUB is required.
- Remove OEM key 1 from keychain.
- Flash the module using the Weblink HUB. Follow the on-screen instructions to complete the keyfob reading process.
- WARNING: Do not press the module programming button. Connect power first. Connect module to vehicle.
- Using OEM key 1, turn key to ON position.
- Wait, LED will turn solid BLUE for 2 seconds.
- Turn key to OFF position.
- Module Programming Procedure completed.
Specifications
| Component | Description |
|---|---|
| Weblink HUB | Required for module programming |
| ACC-RFID1 | Required for remote start |
| CAN Connection | 40-Pin BCM connector |
FAQ
- What is the purpose of the ACC-RFID1?
The ACC-RFID1 is required for remote start as the SUB9 firmware does not provide immobilizer data. - Why is the Weblink HUB necessary?
The Weblink HUB is required for flashing the module and completing the keyfob reading process. - What should I do if the LED flashes red during programming?
Refer to the LED Programming Error Codes section to diagnose the issue based on the number of red flashes.
FTI-STK1: Vehicle Coverage and Preparation Notes
- Covered vehicle use BLADE-AL-SUB9 firmware and the following required accessories, Weblink Hub & ACC RFID1.
- Flash module, and update the controller firmware. Please follow the directions for RFID programming before attempting to program the BLADE module to the vehicle.
- CAN: Type 4 CAN connections are made using the 40-Pin BCM connector and require connecting the white 2-pin female connector to the black male 2-pin connector at marker [D] of the illustration.
- Immobilizer: Type A IMMO requires connecting the white male and female 2-pin connectors at marker [C] of the illustration.
- Lights: Parking lights are pre-wired in the FTI-STK1 harness. Replace the green/white wire of the CM I/O connector with the pre-terminated green/white wire of the harness.
- ACC-RFID1 (REQUIRED): SUB9 firmware does not provide immobilizer data, an ACC-RFID1 is therefore required for remote start 2nd START: The FTI-STK1 harness is pre-wired with a red/black 2nd START output (not required in TYPE 2), cut and insulate the provided wire to prevent short circuits when not used.
- I/O Changes: None required
- Advisory 1: Program ACC-RFID1 before attempting to program the BLADE module to the vehicle. Advisory
- Secure all 2-pin connections, both used and unused, to the main harness body.
FTI-STK1: Installation and Configuration Notes
- REQUIRED ACCESSORY
- ADAPTER NOT REQUIRED
- REQUIRED CONFIGURATION (TYPE A IMMO)
- REQUIRED CONNECTION
- NO CONNECTION
FTI-STK1 – AL-SUB9 – Type 4 2019-22 Subaru Ascent STD KEY AT (USA)
LED Programming Error Codes
Module LED flashing RED during programming
- 1x RED = Unable to communicate with RFID or immobilizer data.
- 2x RED = No CAN activity. Check the CAN wire connections. 3x RED = No ignition detected. Check the ignition wire connection and CAN.
- 4x RED = Required ignition output diode not detected.
INSTALL GUIDE
CARTRIDGE INSTALLATION
- Slide cartridge into unit. Notice button under LED.
Ready for Module Programming Procedure.
MODULE PROGRAMMING PROCEDURE
- For this installation, the Weblink HUB is required.
Remove OEM key 1 from keychain. 
- Place all other keyfobs at least 1 foot away from the Weblink HUB. Failure to comply may result in damage to other keyfobs or interfere with the keyfob reading process.
- Flash the module using the Weblink HUB. Follow the on screen instructions to complete the keyfob reading process.
- WARNING:
- Do not press the module programming button.
- Connect power first. Connect module to vehicle.
- Using OEM key 1, turn key to ON position.
- Turn key to OFF position.
- Module Programming Procedure completed.
Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
FIRSTECH CM7000 Remote Start Plus Security Controller Brain [pdf] Installation Guide CM7000, CM7200, CM-X, CM7000 Remote Start Plus Security Controller Brain, CM7000, Remote Start Plus Security Controller Brain, Start Plus Security Controller Brain, Security Controller Brain, Controller Brain, Brain |
