infineon CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit
Informasi produk
CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit kit sing ngemot sistem-on-modul CYSBSYS-RP01 lan OPTIGATM Trust M keamanan controller. Kit kalebu papan kanthi fitur kaya antena chip, tombol pangguna, 17.2032-MHz ECO, JTAG header, tombol reset, konektor baterei, 3.3-V regulator, Micro-B konektor USB, termistor, KitProg3 tombol pilihan mode programming, lan super kapasitor (mung tilas; ora pedunung ing Papan). Kit kasebut sensitif marang ESD lan kudu dicekel mung dening header tumpukan. Kanggo ngindhari karusakan, kudu diselehake ing permukaan sing ora statis lan ora diluncurake ing permukaan apa wae.
Panggunaan produk
- Priksa manawa sampeyan duwe konektor JST (Adafruit 2750 utawa padha).
- Sambungake papan menyang PC nggunakake kabel USB sing kasedhiya lan ngenteni instalasi driver rampung.
- Priksa manawa baterei wis nyambung lan ngisi daya kanthi mriksa yen LED sing cocog wis mencorong.
- Bukak piranti lunak terminal UART lan sambungake menyang kit.
- Pencet tombol reset (RST_BTN) kanggo ngreset piranti.
- Sampeyan kudu ndeleng output aplikasi sing wis dimuat (scan Wi-Fi) ing terminal serial.
- Dolan maring kit websitus kanggo informasi ing Cepet IoT Experience lan kode examples didhukung kanggo kit iki lan dokumentasi kit.
CYSBSYSKIT-DEV-01 Pinout:
Tabel ing ngisor iki nuduhake pinout kanggo papan CYSBSYSKIT-DEV-01:
| Header | Fungsi onboard utama | PSoCTM 6 MCU pin | Kompatibilitas FeatherWings | Rincian sambungan |
|---|---|---|---|---|
| J1.1 | VBAT | Input sumber baterei Li-Po kanggo mateni regulator daya | ||
| J1.2-J1.6 | EN, GPIO, GPIO, GPIO, GPIO | |||
| J1.7-J1.8 | I2C SCL, I2C SDA | |||
| J1.9 | XRES | |||
| J1.10-J1.11 | Kompatibilitas FeatherWings (Jam SPI, SPI MOSI) | |||
| J1.12 | Kompatibilitas FeatherWings (SPI MISO) | |||
| J5.1 | VDDA, VDDIO | Analog voltage kanggo PSoCTM 6 MCU (ing Rapid IoT Connect sistem-on-modul) |
||
| J5.2 | 3.3 V | |||
| J5.3-J5.6 | NC, GND, Analog, GPIO | |||
| J5.7-J5.16 | Analog, GPIO, Analog, GPIO, Analog, GPIO, Analog, GPIO, SPI Jam, SPI MOSI, SPI MISO, UART RX, UART TX, SPI CS |
Kompatibilitas FeatherWings |
Persiyapan port USB-UART COM kanggo terminal serial kudu dikonfigurasi kanthi mandeg bit 1 lan ora ana kontrol aliran.
Pandhuan wiwitan cepet
Kit pangembang Rapid IoT Connect nganggo modul sistem-on-modul CYSBSYS-RP01 lan pengontrol keamanan OPTIGA™ Trust M CYSBSYSKIT-DEV-01
Papan ndhuwur CYSBSYSKIT-DEV-01 view
Isi kit
Papan CYSBSYSKIT-DEV-01
CYSBSYSKIT-DEV-01 ngisor Papan view
mung tapak sikil; ora pedunung ing Papan
PENTING:
CYSBSYSKIT-DEV-01 Rapid IoT connect pangembang kit sensitif ESD. Tahan papan mung kanthi header tumpukan. Sawise njabut Papan saka kothak, sijine ing lemah, lumahing statis-free. Gunakake bantalan busa konduktif, yen kasedhiya. Aja geser papan ing permukaan apa wae.
Sadurunge sampeyan miwiti
- Priksa manawa sampeyan duwe ing ngisor iki:
- PC nganggo port USB
- Piranti lunak terminal UART kayata Tera Term utawa Minicom
- Kabel USB karo konektor Micro-B ing salah siji mburi
- (Opsional) Baterei Li-Po 3.7-V, 350-mAh kanthi konektor JST (Adafruit 2750 utawa padha)
- Kanthi kabel USB, sambungake papan menyang PC lan ngenteni instalasi driver rampung.
- Priksa manawa LED ing ngisor iki sumunar:
- LED Daya (Biru - LED4)
- KitProg3 Status LED (Kuning – LED3)
- Ngisi daya LED (Kuning - LED5) yen baterei Li-Po disambungake lan ngisi daya
Sambungake kit karo piranti lunak terminal UART
- Bukak piranti lunak terminal UART lan sambungake port USB-UART COM kit kanthi setelan ing ngisor iki:
- Baud rate: 115200, Data: 8 bit, Parity: None, Stop bit: 1 bit, Kontrol aliran: None
- Pencet tombol reset (RST_BTN) kanggo ngreset piranti. Sampeyan kudu ndeleng output aplikasi sing wis dimuat (scan Wi-Fi) ing terminal serial.
Langkah Sabanjure
Dolan maring kit websitus kanggo informasi ing Cepet IoT Experience lan kode examples didhukung kanggo kit iki lan dokumentasi kit.
Kit karo pemetaan pin
Persiyapan port USB-UART COM
Terminal serial
CYSBSYSKIT-DEV-01 pinout
| Header | Fungsi onboard utama | PSoC™ 6 MCU pin | FeatherWings kompatibilitas | Rincian sambungan |
| J1.1 | VBAT | – | – | sumber baterei Li-Po |
| J1.2 | EN | – | – | Input kanggo mateni regulator daya |
| J1.3 | V-BUS | – | – | daya USB |
| J1.4 | GPIO | P9_0 | GPIO13 | – |
| J1.5 | GPIO | P9_1 | GPIO12 | – |
| J1.6 | GPIO | P9_2 | GPIO11 | – |
| J1.7 | GPIO | P9_3 | GPIO10 | – |
| J1.8 | GPIO | P9_4 | GPIO9 | – |
| J1.9 | GPIO | P9_7 | GPIO6 | – |
| J1.10 | GPIO | P8_4 | GPIO5 | – |
| J1.11 | I2C SCL | P6_0 | SCL | Disambungake menyang KitProg3 |
| J1.12 | I2C SDA | P6_1 | SDA | Disambungake menyang KitProg3 |
| J5.1 | XRES | XRES | XRES | – |
| J5.2 | 3.3 V | VDDA, VDDIO | VCC | Analog voltage kanggo PSoC™ 6 MCU (ing sistem-on-modul Rapid IoT Connect) |
| J5.3 | NC | – | – | Ora nyambung |
| J5.4 | GND | – | GND | – |
| J5.5 | Analog GPIO | P10_0 | A0 | – |
| J5.6 | Analog GPIO | P10_1 | A1 | – |
| J5.7 | Analog GPIO | P10_2 | A2 | – |
| J5.8 | Analog GPIO | P10_3 | A3 | – |
| J5.9 | Analog GPIO | P10_4 | A4 | – |
| J5.10 | Analog GPIO | P10_5 | A5 | – |
| J5.11 | Jam SPI | P5_2 | SCK | Jam SPI |
| J5.12 | SPI MOSI | P5_0 | MOSI | SPI Master Out / Slave In (MOSI) |
| J5.13 | SPI MISO | P5_1 | MISO | SPI Master In / Slave Out (MISO |
| J5.14 | UART RX | P6_4 | RX | Disambungake menyang KitProg3 |
| J5.15 | UART TX | P6_5 | TX | Disambungake menyang KitProg3 |
| J5.16 | SPI CS | P5_3 | GPIO14 | Pilih Chip SPI |
Nomer dokumen: 002-30996 Rev. *B
Kabeh hak dilindhungi undhang-undhang. © 2022 Infineon Technologies AG
Dokumen / Sumber Daya
 |
infineon CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit [pdf] Pandhuan pangguna CYSBSYSKIT-DEV-01, CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit, Rapid IoT Connect Developer Kit, IoT Connect Developer Kit, Developer Kit |
