infineon CYSBSYSKIT-DEV-01 Saosaoa IoT Fesoʻotaʻi Atinaʻe Kit

Fa'amatalaga o oloa

O le CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit o se pusa o loʻo i ai le CYSBSYS-RP01 system-on-module ma le OPTIGATM Trust M security controller. O le pusa e aofia ai se laupapa ma foliga e pei o se antenna pu, faʻamau faʻaoga, 17.2032-MHz ECO, JTAG ulutala, faamau toe setiina, feso'ota'iga maa, 3.3-V regulator, Micro-B USB connector, thermistor, KitProg3 programming mode ki filifiliga, ma le super capacitor (na'o tulagavae; e le fa'anofo i luga o le laupapa). O le pusa e ma'ale'ale ile ESD ma e tatau ona na'o ona fa'aulu fa'aputu. Ina ia 'alofia le fa'aleagaina, e tatau ona tu'u i luga o se fa'aele'ele, e leai se mea fa'amau ma aua le fa'ase'e i luga o so'o se mea.

Fa'aogaina o Mea

1. Ia mautinoa e iai sau feso'ota'iga JST (Adafruit 2750 pe tutusa).
2. Faʻafesoʻotaʻi le laupapa i se PC e faʻaaoga ai le USB cable ua saunia ma faʻatali mo le faʻapipiʻiina o le avetaʻavale e maeʻa.
3. Fa'amautinoa o lo'o feso'ota'i le ma'a ma fa'atonuina e ala i le siakiina o lo'o susulu le LED tutusa.
4. Tatala se UART komipiuta terminal ma fa'afeso'ota'i i le pusa.
5. Oomi le faamau toe setiina (RST_BTN) e toe setiina ai le masini.
6. E tatau ona e vaʻai i le gaioiga o le talosaga na muaʻi utaina (Wi-Fi scan) i luga o le laina laina.
7. Asiasi i le pusa webnofoaga mo faʻamatalaga ile Quick IoT Experience ma code example lagolago mo lenei pusa ma pepa fa'amaumauga.

CYSBSYSKIT-DEV-01 Pinout:

O le laulau o loʻo i lalo o loʻo faʻaalia ai le pine mo le CYSBSYSKIT-DEV-01 laupapa:

Ulutala	Galuega autu ile luga ole va'a	PSoCTM 6 MCU pine	FeatherWings fetaui	Fa'amatalaga feso'ota'iga
J1.1	VBAT			Li-Po sapalai maa fa'aoga e tape ai le pule fa'atonu
J1.2-J1.6	EN, GPIO, GPIO, GPIO, GPIO
J1.7-J1.8	I2C SCL, I2C SDA
J1.9	XRES
J1.10-J1.11			FeatherWings fetaui (SPI Uati, SPI MOSI)
J1.12			FeatherWings fetaui (SPI MISO)
J5.1	VDDA, VDDIO			Analog voltage mo PSoCTM 6 MCU (i le Rapid IoT Connect system-on-module)
J5.2	3.3 V
J5.3-J5.6	NC, GND, Analog, GPIO
J5.7-J5.16	Analog, GPIO, Analog, GPIO, Analog, GPIO, Analog, GPIO, SPI Uati, SPI MOSI, SPI MISO, UART RX, UART TX, SPI CS		FeatherWings fetaui

O le seti o le uafu USB-UART COM mo le laina laina e tatau ona faʻapipiʻiina i se taofi o le 1 bit ma leai se faʻatonuga o le tafe.

Ta'iala vave amata

Rapid IoT Fesoʻotaʻi pusa faʻapipiʻi faʻatasi ma le CYSBSYS-RP01 system-on-module ma le OPTIGA ™ Trust M faʻatonuina le puipuiga CYSBSYSKIT-DEV-01

CYSBSYSKIT-DEV-01 laupapa pito i luga view

mea i totonu o pusa
CYSBSYSKIT-DEV-01 laupapa

CYSBSYSKIT-DEV-01 laupapa pito i lalo view

Na'o tulagavae; e le o fa'atumuina i luga o le laupapa

TAUA:
CYSBSYSKIT-DEV-01 Rapid IoT connect developer kit e maaleale ile ESD. Taofi le laupapa i ona ulutala faaputu. A uma ona aveese le laupapa mai lana atigipusa, tuu i luga o le eleele e leai se mea. Fa'aaogā se pa'u fa'a'ave'ave, pe'ā maua. Aua le fa'ase'e le laupapa i luga o so'o se mea.

Ae e te le'i amataina

1. Ia mautinoa o loʻo ia te oe mea nei:
   1. PC ma uafu USB
   2. UART polokalama fa'apipi'i pei ole Tera Term po'o le Minicom
   3. Uaea USB ma so'oga Micro-B ile tasi pito
   4. (Filifili) 3.7-V, 350-mAh Li-Po maa ma le JST so'oga (Adafruit 2750 pe tutusa)
2. Faatasi ai ma le USB cable, faʻafesoʻotaʻi le laupapa i le PC ma faʻatali mo le faʻapipiʻiina o le avetaʻavale e maeʻa.
3. Ia fa'amautinoa o lo'o susulu moli nei:
   1. LED Malosi (Laumouli – LED4)
   2. KitProg3 Tulaga LED (Samasama – LED3)
   3. Fa'atauina le LED (Yellow - LED5) pe a feso'ota'i le maa Li-Po ma fa'aola

Fa'afeso'ota'i le pusa ma le UART terminal software

1. Tatala le polokalama UART terminal ma faʻafesoʻotaʻi le pusa USB-UART COM o le pusa ma tulaga nei:
   1. Fua o le Baud: 115200, Faʻamatalaga: 8 bit, Faʻatasi: Leai, Taofi: 1 bit, Pulea tafe: Leai
2. Oomi le faamau toe setiina (RST_BTN) e toe setiina ai le masini. E tatau ona e vaʻai i le gaioiga o le talosaga na muaʻi utaina (Wi-Fi scan) i luga o le laina laina.

Laasaga Sosoo
Asiasi i le pusa webnofoaga mo faʻamatalaga ile Quick IoT Experience ma code example lagolago mo lenei pusa ma pepa fa'amaumauga.

Pusa ma fa'afanua pine

Seti uafu USB-UART COM

Fa'asologa fa'asologa

CYSBSYSKIT-DEV-01 pinout

Ulutala	Galuega autu ile luga ole va'a	PSoC™ 6 MCU pine	FeatherWings fetaui lelei	Fa'amatalaga feso'ota'iga
J1.1	VBAT	–	–	Sapalai maa Li-Po
J1.2	EN	–	–	Fa'aoga e tape ai le pule fa'atonu
J1.3	V-PUS	–	–	USB mana
J1.4	GPIO	P9_0	GPIO13	–
J1.5	GPIO	P9_1	GPIO12	–
J1.6	GPIO	P9_2	GPIO11	–
J1.7	GPIO	P9_3	GPIO10	–
J1.8	GPIO	P9_4	GPIO9	–
J1.9	GPIO	P9_7	GPIO6	–
J1.10	GPIO	P8_4	GPIO5	–
J1.11	I2C SCL	P6_0	SCL	Feso'ota'i ile KitProg3
J1.12	I2C SDA	P6_1	SDA	Feso'ota'i ile KitProg3
J5.1	XRES	XRES	XRES	–
J5.2	3.3 V	VDDA, VDDIO	VCC	Analog voltage mo PSoC™ 6 MCU (i le Rapid IoT Connect system-on-module)
J5.3	NC	–	–	Le feso'ota'i
J5.4	GND	–	GND	–
J5.5	GPIO fa'atusa	P10_0	A0	–
J5.6	GPIO fa'atusa	P10_1	A1	–
J5.7	GPIO fa'atusa	P10_2	A2	–
J5.8	GPIO fa'atusa	P10_3	A3	–
J5.9	GPIO fa'atusa	P10_4	A4	–
J5.10	GPIO fa'atusa	P10_5	A5	–
J5.11	Uati SPI	P5_2	SCK	SPI uati
J5.12	SPI MOSI	P5_0	MOSI	SPI Matai i fafo / Pologa i totonu (MOSI)
J5.13	SPI MISO	P5_1	MISO	SPI Matai i totonu / Pologa i fafo (MISO
J5.14	UART RX	P6_4	RX	Feso'ota'i ile KitProg3
J5.15	UART TX	P6_5	TX	Feso'ota'i ile KitProg3
J5.16	SPI CS	P5_3	GPIO14	SPI Chip Filifili

Numera o pepa: 002-30996 Rev. *B
Ua taofia aia tatau uma. © 2022 Infineon Technologies AG

Pepa / Punaoa

infineon CYSBSYSKIT-DEV-01 Saosaoa IoT Fesoʻotaʻi Atinaʻe Kit [pdf] Taiala mo Tagata Fa'aoga CYSBSYSKIT-DEV-01, CYSBSYSKIT-DEV-01 Vape IoT Feso'ota'i Pusa Fa'atupu, Vave IoT Feso'ota'i Pusa Fa'atupu, IoT Feso'ota'i Pusa Fa'atupu, Kit Fa'atupuina

Fa'asinomaga

• Tusi Taiala