infineon CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit
Product Information
The CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit is a kit that contains a CYSBSYS-RP01 system-on-module and an OPTIGATM Trust M security controller. The kit includes a board with features like a chip antenna, user button, 17.2032-MHz ECO, JTAG header, reset button, battery connector, 3.3-V regulator, Micro-B USB connector, thermistor, KitProg3 programming mode selection button, and a super capacitor (footprint only; not populated on the board). The kit is sensitive to ESD and should be held only by its stack-up headers. To avoid damage, it should be placed on a grounded, static-free surface and not slid over any surface.
Product Usage
- Ensure that you have a JST connector (Adafruit 2750 or similar).
- Connect the board to a PC using the USB cable provided and wait for the driver installation to complete.
- Verify that the battery is connected and charging by checking that the corresponding LED is glowing.
- Open a UART terminal software and connect it to the kit.
- Press the reset button (RST_BTN) to reset the device.
- You should see the output of the pre-loaded application (Wi-Fi scan) on the serial terminal.
- Visit the kit website for information on Quick IoT Experience and code examples supported for this kit and kit documentation.
CYSBSYSKIT-DEV-01 Pinout:
The table below shows the pinout for the CYSBSYSKIT-DEV-01 board:
| Header | Primary onboard function | PSoCTM 6 MCU pin | FeatherWings compatibility | Connection details |
|---|---|---|---|---|
| J1.1 | VBAT | Li-Po battery supply input to turn OFF power regulators | ||
| J1.2-J1.6 | EN, GPIO, GPIO, GPIO, GPIO | |||
| J1.7-J1.8 | I2C SCL, I2C SDA | |||
| J1.9 | XRES | |||
| J1.10-J1.11 | FeatherWings compatibility (SPI Clock, SPI MOSI) | |||
| J1.12 | FeatherWings compatibility (SPI MISO) | |||
| J5.1 | VDDA, VDDIO | Analog voltage for PSoCTM 6 MCU (in the Rapid IoT Connect system-on-module) | ||
| J5.2 | 3.3 V | |||
| J5.3-J5.6 | NC, GND, Analog, GPIO | |||
| J5.7-J5.16 | Analog, GPIO, Analog, GPIO, Analog, GPIO, Analog, GPIO, SPI Clock, SPI MOSI, SPI MISO, UART RX, UART TX, SPI CS | FeatherWings compatibility |
The USB-UART COM port setup for the serial terminal should be configured with a stop bit of 1 bit and no flow control.
Quick start guide
Rapid IoT Connect developer kit with CYSBSYS-RP01 system-on-module and OPTIGA™ Trust M security controller CYSBSYSKIT-DEV-01
CYSBSYSKIT-DEV-01 board top view
Kit contents
CYSBSYSKIT-DEV-01 board
CYSBSYSKIT-DEV-01 board bottom view
Footprint only; not populated on the board
IMPORTANT:
CYSBSYSKIT-DEV-01 Rapid IoT connect developer kit is sensitive to ESD. Hold the board only by its stack-up headers. After removing the board from its box, place it on a grounded, static-free surface. Use a conductive foam pad, if available. Do not slide the board over any surface.
Before you start
- Ensure that you have the following:
- PC with USB port
- UART terminal software such as Tera Term or Minicom
- USB cable with Micro-B connector at one end
- (Optional) 3.7-V, 350-mAh Li-Po battery with JST connector (Adafruit 2750 or similar)
- With the USB cable, connect the board to the PC and wait for the driver installation to complete.
- Verify that the following LEDs glow:
- Power LED (Blue – LED4)
- KitProg3 Status LED (Yellow – LED3)
- Charging LED (Yellow – LED5) if the Li-Po battery is connected and charging
Connect the kit with the UART terminal software
- Open the UART terminal software and connect the kit’s USB-UART COM port with the following settings:
- Baud rate: 115200, Data: 8 bit, Parity: None, Stop bit: 1 bit, Flow control: None
- Press the reset button (RST_BTN) to reset the device. You should see the output of the pre-loaded application (Wi-Fi scan) on the serial terminal.
Next Steps
Visit the kit website for information on Quick IoT Experience and code examples supported for this kit and kit documentation.
Kit with pin mapping
USB-UART COM port setup
Serial terminal
CYSBSYSKIT-DEV-01 pinout
| Header | Primary onboard function | PSoC™ 6 MCU pin | FeatherWings compatibility | Connection details |
| J1.1 | VBAT | – | – | Li-Po battery supply |
| J1.2 | EN | – | – | Input to turn OFF power regulators |
| J1.3 | VBUS | – | – | USB power |
| J1.4 | GPIO | P9_0 | GPIO13 | – |
| J1.5 | GPIO | P9_1 | GPIO12 | – |
| J1.6 | GPIO | P9_2 | GPIO11 | – |
| J1.7 | GPIO | P9_3 | GPIO10 | – |
| J1.8 | GPIO | P9_4 | GPIO9 | – |
| J1.9 | GPIO | P9_7 | GPIO6 | – |
| J1.10 | GPIO | P8_4 | GPIO5 | – |
| J1.11 | I2C SCL | P6_0 | SCL | Connected to KitProg3 |
| J1.12 | I2C SDA | P6_1 | SDA | Connected to KitProg3 |
| J5.1 | XRES | XRES | XRES | – |
| J5.2 | 3.3 V | VDDA, VDDIO | VCC | Analog voltage for PSoC™ 6 MCU (in the Rapid IoT Connect system-on-module) |
| J5.3 | NC | – | – | Not connected |
| J5.4 | GND | – | GND | – |
| J5.5 | Analog GPIO | P10_0 | A0 | – |
| J5.6 | Analog GPIO | P10_1 | A1 | – |
| J5.7 | Analog GPIO | P10_2 | A2 | – |
| J5.8 | Analog GPIO | P10_3 | A3 | – |
| J5.9 | Analog GPIO | P10_4 | A4 | – |
| J5.10 | Analog GPIO | P10_5 | A5 | – |
| J5.11 | SPI Clock | P5_2 | SCK | SPI clock |
| J5.12 | SPI MOSI | P5_0 | MOSI | SPI Master Out / Slave In (MOSI) |
| J5.13 | SPI MISO | P5_1 | MISO | SPI Master In / Slave Out (MISO |
| J5.14 | UART RX | P6_4 | RX | Connected to KitProg3 |
| J5.15 | UART TX | P6_5 | TX | Connected to KitProg3 |
| J5.16 | SPI CS | P5_3 | GPIO14 | SPI Chip Select |
Document number: 002-30996 Rev. *B
All rights reserved. © 2022 Infineon Technologies AG
Documents / Resources
 | infineon CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit [pdf] User Guide CYSBSYSKIT-DEV-01, CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit, Rapid IoT Connect Developer Kit, IoT Connect Developer Kit, Developer Kit |
