infineon CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit

Tlhahisoleseding ya Sehlahiswa

CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit ke sesebelisoa se nang le CYSBSYS-RP01 system-on-module le molaoli oa ts'ireletso oa OPTIGATM Trust M. Thepa e kenyelletsa boto e nang le likarolo tse kang antenna ea chip, konopo ea mosebedisi, 17.2032-MHz ECO, J.TAG hlooho, konopo ea reset, sehokelo sa betri, 3.3-V regulator, Micro-B USB connector, thermistor, KitProg3 konopo ea ho khetha mokhoa oa lenaneo, le super capacitor (mooto oa maoto feela; ha o na batho ka boto). Kit e na le maikutlo a ESD mme e lokela ho ts'oaroa feela ke lihlooho tsa eona tse bokellaneng. E le ho qoba tšenyo, e lokela ho behoa holim'a fatše, e se nang static mme e se ke ea thella holim'a sebaka leha e le sefe.

Tšebeliso ea Sehlahisoa

1. Netefatsa hore o na le sehokedi sa JST (Adafruit 2750 kapa se tshwanang).
2. Hokela boto ho PC u sebelisa thapo ea USB e fanoeng 'me u emele hore mokhanni o phethe.
3. Netefatsa hore betri e hokahane le ho tjhaja ka ho sheba hore na LED e tsamaisanang le yona e a kganya.
4. Bula software ea terminal ea UART ebe u e hokahanya le khiti.
5. Tobetsa konopo ea ho seta botjha (RST_BTN) ho seta sesebediswa botjha.
6. U lokela ho bona tlhahiso ea ts'ebeliso e kentsoeng esale pele (scan ea Wi-Fi) ho terminal ea serial.
7. Etela lisebelisoa websebaka sa marang-rang bakeng sa tlhaiso-leseling ka Boiphihlelo ba Quick IoT le khoutu ea exampLes e tšehetsoa bakeng sa litokomane tsa kit le kit.

CYSBSYSKIT-DEV-01 Pinout:

Tafole e ka tlase e bonts'a pinout bakeng sa boto ea CYSBSYSKIT-DEV-01:

Hlooho	Mosebetsi oa mantlha oa onboard	PSoCTM 6 MCU phini	Ho lumellana ha FeatherWings	Lintlha tsa khokahano
J1.1	VBAT			Kenyelletso ea phepelo ea betri ea Li-Po ho tima balaoli ba motlakase
J1.2-J1.6	EN, GPIO, GPIO, GPIO, GPIO
J1.7-J1.8	I2C SCL, I2C SDA
J1.9	XRES
J1.10-J1.11			Tšebelisano ea Masiba (SPI Clock, SPI MOSI)
J1.12			Tšebelisano ea Masiba (SPI MISO)
J5.1	VDDA, VDDIO			Analoge voltage bakeng sa PSoCTM 6 MCU (ho Rapid IoT Connect sistimi e ho-module)
J5.2	3.3 V
J5.3-J5.6	NC, GND, Analog, GPIO
J5.7-J5.16	Analog, GPIO, Analog, GPIO, Analog, GPIO, Analog, GPIO, SPI Oache, SPI MOSI, SPI MISO, UART RX, UART TX, SPI CS		Ho lumellana ha FeatherWings

Setupo sa boema-kepe ba USB-UART COM bakeng sa terminal ea serial se lokela ho hlophisoa ka sekheo sa 1 bit mme ho se na taolo ea phallo.

Tataiso ea ho qala kapele

Rapid IoT Connect kit e nang le CYSBSYS-RP01 system-on-module le OPTIGA™ Trust M molaoli oa ts'ireletso CYSBSYSKIT-DEV-01

CYSBSYSKIT-DEV-01 board top view

Likahare tsa Kit
CYSBSYSKIT-DEV-01 board

CYSBSYSKIT-DEV-01 boto tlase view

Papiso ea maoto feela; ha e na batho ka boto

BOHLOKOA:
CYSBSYSKIT-DEV-01 Rapid IoT connect developer kit e hlokolosi ho ESD. Tšoara boto feela ka lihlooho tsa eona tse bokellaneng. Ka mor'a ho tlosa boto ka lebokoseng la eona, e behe sebakeng se fatše, se se nang static. Sebelisa foam pad, haeba e le teng. U se ke ua thellela boto holim'a sebaka leha e le sefe.

Pele o qala

1. Netefatsa hore o na le tse latelang:
   1. PC e nang le koung ea USB
   2. Software ea terminal ea UART joalo ka Tera Term kapa Minicom
   3. Cable ea USB e nang le sehokelo sa Micro-B pheletsong e 'ngoe
   4. (Ka boikhethelo) 3.7-V, 350-mAh Li-Po betri e nang le sehokelo sa JST (Adafruit 2750 kapa tse ling tse tšoanang)
2. Ka thapo ya USB, hokela boto ho PC mme o emetse hore ho kengoa mokhanni ho phethehe.
3. Netefatsa hore li-LED tse latelang lia khanya:
   1. Matla a LED (Boputsoa - LED4)
   2. LED ea Boemo ba KitProg3 (Bosehla - LED3)
   3. Ho tjhaja LED (Yellow – LED5) haeba betri ya Li-Po e hoketswe mme e tjhaja

Hokela khiti le software ea terminal ea UART

1. Bula software ea terminal ea UART ebe o hokela kou ea USB-UART COM ea kit ka litlhophiso tse latelang:
   1. Sekhahla sa Baud: 115200, Data: 8 bit, Parity: Ha ho letho, Stop bit: 1 bit, Taolo ea phallo: Ha ho letho
2. Tobetsa konopo ea ho seta botjha (RST_BTN) ho seta sesebediswa botjha. U lokela ho bona tlhahiso ea ts'ebeliso e kentsoeng esale pele (scan ea Wi-Fi) ho terminal ea serial.

Mehato e Latelang
Etela lisebelisoa websebaka sa marang-rang bakeng sa tlhaiso-leseling ka Boiphihlelo ba Quick IoT le khoutu ea exampLes e tšehetsoa bakeng sa litokomane tsa kit le kit.

Kit e nang le 'mapa oa pin

Tlhophiso ea boema-kepe ba USB-UART COM

Terminal ea serial

Tlhaloso: CYSBSYSKIT-DEV-01

Hlooho	Mosebetsi oa mantlha oa onboard	PSoC™ 6 MCU pin	FeatherWings ho tsamaellana	Lintlha tsa khokahano
J1.1	VBAT	–	–	Phepelo ea betri ea Li-Po
J1.2	EN	–	–	Kenyo ea ho tima lilaoli tsa motlakase
J1.3	V-BUS	–	–	Matla a USB
J1.4	GPIO	P9_0	GPIO13	–
J1.5	GPIO	P9_1	GPIO12	–
J1.6	GPIO	P9_2	GPIO11	–
J1.7	GPIO	P9_3	GPIO10	–
J1.8	GPIO	P9_4	GPIO9	–
J1.9	GPIO	P9_7	GPIO6	–
J1.10	GPIO	P8_4	GPIO5	–
J1.11	I2C SCL	P6_0	SCL	E hokahane le KitProg3
J1.12	I2C SDA	P6_1	SDA	E hokahane le KitProg3
J5.1	XRES	XRES	XRES	–
J5.2	3.3 V	VDDA, VDDIO	VCC	Analoge voltage bakeng sa PSoC™ 6 MCU (ho Rapid IoT Connect system-on-module)
J5.3	NC	–	–	Ha e kopane
J5.4	GND	–	GND	–
J5.5	Analoji GPIO	P10_0	A0	–
J5.6	Analoji GPIO	P10_1	A1	–
J5.7	Analoji GPIO	P10_2	A2	–
J5.8	Analoji GPIO	P10_3	A3	–
J5.9	Analoji GPIO	P10_4	A4	–
J5.10	Analoji GPIO	P10_5	A5	–
J5.11	Clock ea SPI	P5_2	TS'ELISO	Oache ea SPI
J5.12	SPI MOSI	P5_0	MOSI	SPI Master Out / Slave In (MOSI)
J5.13	SPI MISO	P5_1	MISO	SPI Master In / Slave Out (MISO
J5.14	UART RX	P6_4	RX	E hokahane le KitProg3
J5.15	UART TX	P6_5	TX	E hokahane le KitProg3
J5.16	Tlhaloso: SPI CS	P5_3	GPIO14	Khetho ea SPI Chip

Nomoro ea Tokomane: 002-30996 Rev. *B
Litokelo tsohle li sirelelitsoe. © 2022 Infineon Technologies AG

Litokomane / Lisebelisoa

infineon CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit [pdf] Bukana ea Mosebelisi CYSBSYSKIT-DEV-01, CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit, Rapid IoT Connect Developer Kit, IoT Connect Developer Kit, Developer Kit

Litšupiso

• Bukana ea Mosebelisi