EPEVER EPIPDB-COM-10 Dual Baterei PWM Ngisi daya Controller

Penampilan

WARNING

Aja nginstal controller ing lembab, semprotan uyah, karat, greasy, flammable, mbledhos, bledug accumulative, utawa lingkungan abot liyane.

(Cathetan: connect the components as the 1-6)

Ikon	Fungsi
	Sambungake karo baterei #1.
	Sambungake karo baterei #2.
	Sambungake karo array PV.
Remote temp. sensor (Optional)	Remotely measure the battery temperature to regulate the battery voltage.
Suhu lokal. sensor	Measure ambient temperature.
Kanggo baterei 1	Indicate battery #1 charging status and error.
Kanggo baterei 2	Indicate battery #2 charging status and error.
Sambungan meter jarak jauh	Sambungake karo meter remot.

Cathetan: No RTS; the controller measures ambient temperature by the local temp. sensor. While the controller will obtain data from the RTS automatically after the RTS is connected.

EPIPDB-COM series are common-negative controllers. Negative terminals of the PV array and batteries can be grounded simultaneously, or any negative terminal is grounded. According to the practical application, the negative terminals of the PV array and batteries can also be ungrounded.

However, the grounding terminal on the controller shell must be grounded.

It can shield electromagnetic interference and avoid electric shock to the human body.

AWAS	Gunakake pengontrol umum-negatif kanggo sistem umum-negatif, kayata sistem RV, dianjurake. Pengontrol bisa rusak yen pengontrol umum-positif digunakake lan elektroda positif dilebokake ing sistem umum-negatif.

Setelan Mode

jinis baterei	modus
charging priority
charging frequence

Three LEDs flash, and each LED indicates different specifications. Choose the LED according to the following information, and then press the button for 5 seconds until the number flashes. And then, choose one number you need and leave it, and the number will be saved.

1. 1st LED is for the battery type setting.
   

   1st LED	Jinis baterei
   1	Baterei sing disegel
   2	Batere gel
   3	Baterei kebanjiran

2. 2nd LED is for the charging priority setting. Set the percentage for battery #1, and the controller will automatically calculate the rest percentage kanggo baterei #2.
   

   2nd LED	Baterei #1 persen pangisian dayatage	Battery # 2 Ngisi daya percentage
   0	0%	100%
   1	10%	90%
   2	20%	80%
   3	30%	70%
   4	40%	60%
   5	50%	50%
   6	60%	40%
   7	70%	30%
   8	80%	20%
   9	90% (pre-set)	10%

   Cathetan: During the normal charging process, the controller charges the battery per the set percentage. Yen baterei siji wis kebak (kayata baterei #1), arus pangisi daya liyane bakal dialihake menyang baterei liyane (baterei #2). Kontroler kanthi otomatis bali menyang setelan persentage nalika baterei # 1 kurang voltage.
   When the controller detects only one battery, all the charging current will go to this battery automatically.
3. 3rd LED is for the charging frequency setting.
   

   3rd LED	Frekuensi pengisian PWM
   0	25Hz (pra-setel)
   1	50Hz
   2	100Hz

Ngatasi masalah

Ora.	Status LED	Ngatasi masalah
1	LED kelip-kelip	Short circuit. Please check whether the PV and battery connection is correct.
2	LED slowly flashing	Kebak daya
3	LED ON	Ing ngisi daya
4	LED frequent flashing	Ora ana pangisi daya utawa baterei sing dideteksi.
5	LED MATI	Ora baterei utawa sistem liwat voltage.

Informasi Teknis

Model	EPIPDB-COM-10	EPIPDB-COM-20
Sistem nominal voltage	12 / 24VDC Otomatis
Rated daya saiki	10A	20A
Jinis baterei	Disegel; gel; kebanjiran
Equalize pengisian voltage	disegel: 14.6V; Gel: Ora; Banjir: 14.8V
Boost pengisian voltage	disegel: 14.4V; Gel: 14.2V; Banjir: 14.6V
Pengisian floating voltage	Disegel / Gel / Banjir: 13.8V
Volume surya maksimaltage	30V(12V System); 55V(24V System)
Batere voltage sawetara	8 ~ 15V
Ngedongkrak wektu	120 menit
Konsumsi dhewe	4mA ing wayah wengi; 10mA nalika ngisi daya
port komunikasi	8-PIN RJ-45
Temp. ganti rugi	-5mV / ℃ / 2V
Terminal	4mm2
Suhu lingkungan	-35 ℃ ~ +55 ℃
bobot net	250g

Note: The above parameters are measured in the condition of a 12V system. Please double the values in the 24V system.

Gambar mekanik

Nomer Versi: V3.1

Dhukungan Pelanggan

HUIZHOU EPEVER TECHNOLOGY CO., LTD.
Telpon: +86-752-3889706
E-mail: info@epever.com
Websitus: www.epever.com

Dokumen / Sumber Daya

EPEVER EPIPDB-COM-10 Dual Baterei PWM Ngisi daya Controller [pdf] Manual pangguna EPIPDB-COM-10, EPIPDB-COM-20, EPIPDB-COM-10 Dual Battery PWM Charge Controller, EPIPDB-COM-10, Dual Battery PWM Charge Controller, Battery PWM Charge Controller, PWM Charge Controller, Charge Controller

Referensi

• Manual pangguna