EPEVER EPIPDB-COM-10 Dual Battery PWM Charge Controller

Hitsura

BABALA

Huwag i-install ang controller sa humid, salt spray, corrosion, mamantika, nasusunog, sumasabog, dust accumulative, o iba pang malalang kapaligiran.

(Tandaan: connect the components as the 1-6)

Icon	Function
	Kumonekta sa baterya #1.
	Kumonekta sa baterya #2.
	Kumonekta sa PV array.
Remote temp. sensor (Optional)	Remotely measure the battery temperature to regulate the battery voltage.
Lokal na temp. sensor	Measure ambient temperature.
Para sa baterya 1	Indicate battery #1 charging status and error.
Para sa baterya 2	Indicate battery #2 charging status and error.
Remote meter na koneksyon	Kumonekta sa isang remote meter.

Tandaan: No RTS; the controller measures ambient temperature by the local temp. sensor. While the controller will obtain data from the RTS automatically after the RTS is connected.

EPIPDB-COM series are common-negative controllers. Negative terminals of the PV array and batteries can be grounded simultaneously, or any negative terminal is grounded. According to the practical application, the negative terminals of the PV array and batteries can also be ungrounded.

However, the grounding terminal on the controller shell must be grounded.

It can shield electromagnetic interference and avoid electric shock to the human body.

MAG-INGAT

Inirerekomenda ang paggamit ng common-negative na controller para sa mga common-negative na system, gaya ng RV system. Maaaring masira ang controller kung gumamit ng common-positive controller at ang positive electrode ay naka-ground sa common-negative system.

Setting ng Mode

uri ng baterya	mode
charging priority
charging frequence

Three LEDs flash, and each LED indicates different specifications. Choose the LED according to the following information, and then press the button for 5 seconds until the number flashes. And then, choose one number you need and leave it, and the number will be saved.

1. 1st LED is for the battery type setting.
   

   1st LED	Uri ng baterya
   1	Naka-sealed na baterya
   2	Baterya ng gel
   3	Binaha ang baterya

2. 2nd LED is for the charging priority setting. Set the percentage for battery #1, and the controller will automatically calculate the rest percentage para sa baterya #2.
   

   2nd LED	Baterya #1 porsyento ng pagsingiltage	Battery # 2 Porsyento ng pagsingiltage
   0	0%	100%
   1	10%	90%
   2	20%	80%
   3	30%	70%
   4	40%	60%
   5	50%	50%
   6	60%	40%
   7	70%	30%
   8	80%	20%
   9	90%(pre-set)	10%

   Tandaan: During the normal charging process, the controller charges the battery per the set percentage. Kung ang isang baterya ay ganap na na-charge (tulad ng baterya #1), mas maraming kasalukuyang charge ang ililihis sa kabilang baterya (baterya #2). Awtomatikong babalik ang controller sa setting na porsyentotage kapag mahina ang baterya #1 voltage.
   When the controller detects only one battery, all the charging current will go to this battery automatically.
3. 3rd LED is for the charging frequency setting.
   

   3rd LED	PWM charging frequency
   0	25Hz(pre-set)
   1	50Hz
   2	100Hz

Pag-troubleshoot

Hindi.	Katayuan ng LED	Pag-troubleshoot
1	LED na kumikislap	Short circuit. Please check whether the PV and battery connection is correct.
2	LED slowly flashing	Ganap na naka-charge
3	HUMANTONG SA	Sa pagsingil
4	LED frequent flashing	Walang na-detect na pag-charge o anumang baterya.
5	NAKA-OFF ang LED	Walang baterya o sistema sa voltage.

Teknikal na Impormasyon

Modelo	EPIPDB-COM-10	EPIPDB-COM-20
Nominal na sistema voltage	12 / 24VDC Auto
Na-rate ang kasalukuyang singil	10A	20A
Uri ng Baterya	selyadong; Gel; Binaha
I-equalize ang pagsingil voltage	Selyadong: 14.6V; Gel: Hindi; Binaha: 14.8V
Palakasin ang pagsingil ng voltage	Selyadong: 14.4V; Gel: 14.2V; Binaha: 14.6V
Float charging voltage	Naka-sealed/Gel/Binaha: 13.8V
Pinakamataas na solar voltage	30V(12V System); 55V(24V System)
Baterya voltage saklaw	8 ~ 15V
Palakasin ang oras	120 minuto
Pagkonsumo sa sarili	4mA sa gabi; 10mA sa pagcha-charge
Port ng komunikasyon	8-PIN RJ-45
Temp. kabayaran	-5mV / ℃ / 2V
Mga terminal	4mm2
Temperatura ng kapaligiran	-35 ℃ ~ +55 ℃
Net timbang	250g

Note: The above parameters are measured in the condition of a 12V system. Please double the values in the 24V system.

Pagguhit ng Mekanikal

Numero ng Bersyon: V3.1

Suporta sa Customer

HUIZHOU EPEVER TECHNOLOGY CO., LTD.
Tel: +86-752-3889706
E-mail: info@epever.com
Website: www.epever.com

Mga Dokumento / Mga Mapagkukunan

EPEVER EPIPDB-COM-10 Dual Battery PWM Charge Controller [pdf] User Manual EPIPDB-COM-10, EPIPDB-COM-20, EPIPDB-COM-10 Dual Battery PWM Charge Controller, EPIPDB-COM-10, Dual Battery PWM Charge Controller, Battery PWM Charge Controller, PWM Charge Controller, Charge Controller

Mga sanggunian

• User Manual