EPEVER EPIPDB-COM-10 Onye njikwa chaja PWM Batrị abụọ

Ọdịdị

Ịdọ aka ná ntị

Awụnyela ihe njikwa na iru mmiri, ịgba nnu, corrosion, griiz, ọkụ ọkụ, mgbawa, mkpokọ uzuzu, ma ọ bụ gburugburu ebe ndị ọzọ siri ike.

(Rịba ama: connect the components as the 1-6)

Akara ngosi	Ọrụ
	Jikọọ na batrị #1.
	Jikọọ na batrị #2.
	Jikọọ na PV n'usoro.
Remote temp. sensor (Optional)	Remotely measure the battery temperature to regulate the battery voltage.
Okpomọkụ mpaghara. ihe mmetụta	Measure ambient temperature.
Maka batrị 1	Indicate battery #1 charging status and error.
Maka batrị 2	Indicate battery #2 charging status and error.
Njikọ mita dịpụrụ adịpụ	Jikọọ na mita dịpụrụ adịpụ.

Mara: No RTS; the controller measures ambient temperature by the local temp. sensor. While the controller will obtain data from the RTS automatically after the RTS is connected.

EPIPDB-COM series are common-negative controllers. Negative terminals of the PV array and batteries can be grounded simultaneously, or any negative terminal is grounded. According to the practical application, the negative terminals of the PV array and batteries can also be ungrounded.

However, the grounding terminal on the controller shell must be grounded.

It can shield electromagnetic interference and avoid electric shock to the human body.

kpachara anya

Iji njikwa na-adịghị mma maka sistemu na-adịghị mma, dị ka usoro RV, ka akwadoro. Onye njikwa ahụ nwere ike mebie ma ọ bụrụ na ejiri onye na-ahụ maka ihe na-eme ka ọ bụrụ ihe na-eme ka ọ dị mma ma na-adabere na electrode dị mma na usoro ihe na-adịghị mma.

Ntọala ọnọdụ

ụdị batrị	ọnọdụ
charging priority
charging frequence

Three LEDs flash, and each LED indicates different specifications. Choose the LED according to the following information, and then press the button for 5 seconds until the number flashes. And then, choose one number you need and leave it, and the number will be saved.

1. 1st LED is for the battery type setting.
   

   1st Ikanam	Ụdị batrị
   1	batrị emechiri emechi
   2	Gel batrị
   3	Batrị iju mmiri

2. 2nd LED is for the charging priority setting. Set the percentage for battery #1, and the controller will automatically calculate the rest percentage maka batrị #2.
   

   2nd Ikanam	Batrị #1 charging percentage	Battery # 2 Nchaji pasenttage
   0	0%	100%
   1	10%	90%
   2	20%	80%
   3	30%	70%
   4	40%	60%
   5	50%	50%
   6	60%	40%
   7	70%	30%
   8	80%	20%
   9	90% (Edobere ya)	10%

   Mara: During the normal charging process, the controller charges the battery per the set percentage. Ọ bụrụ na otu batrị chajịchara nke ọma (dịka batrị #1), a ga-atụgharị chaja chaja karịa na batrị nke ọzọ (batrị #2). Onye njikwa na-alaghachi na akpaghị aka na pasent ntọalatage mgbe batrị #1 dị ala voltage.
   When the controller detects only one battery, all the charging current will go to this battery automatically.
3. 3rd LED is for the charging frequency setting.
   

   3rd Ikanam	Ugboro nchaji PWM
   0	25Hz (Edobere ya)
   1	50Hz
   2	100Hz

Nchọpụta nsogbu

Mba.	Ọnọdụ LED	Nchọpụta nsogbu
1	Ikanam na-egbuke egbuke	Short circuit. Please check whether the PV and battery connection is correct.
2	LED slowly flashing	Ebubo zuru oke
3	Ikanam ON	Na ịchaji
4	LED frequent flashing	Enweghị chaja ma ọ bụ batrị ọ bụla achọpụtara.
5	Gbanyụọ	Enweghị batrị ma ọ bụ sistemụ karịrị voltage.

Ozi nka

Nlereanya	EPIPDB-COM-10	EPIPDB-COM-20
Usoro ọnụ ọnụ voltage	12/24VDC Nchekwa onwe
Enyere ụgwọ ugbu a	10A	20A
Ụdị batrị	Akara akara; Gel; Iju mmiri juru
Hazie nchaji voltage	Akara: 14.6V; Gel: Mba; Iju mmiri: 14.8V
Boost chaja voltage	Akara: 14.4V; Gel: 14.2V; Iju mmiri: 14.6V
Nchaji ese n'elu voltage	Akara akara/gel/Iju mmiri: 13.8V
Oke anyanwụ voltage	30V(12V System); 55V(24V System)
Batrị voltage oke	8 ~ 15V
Oge nkwalite	120 nkeji
Iri onwe ya	4mA n'abalị; 10mA na chaja
ọdụ ụgbọ mmiri nkwukọrịta	8-PIN RJ-45
Okpomọkụ nkwụghachi ụgwọ	-5mV/ ℃/2V
Ọnụ ụzọ	4mm2
Okpomọkụ gburugburu	-35 ℃ ~ +55 ℃
Nha ịbụ	250g

Note: The above parameters are measured in the condition of a 12V system. Please double the values in the 24V system.

Ihe osise igwe

Nọmba ụdị: V3.1

Nkwado ndị ahịa

Ụlọ ọrụ HUIZHOU EPEVER TECHNOLOGY CO., LTD.
Tel: + 86-752-3889706
Email: info@epever.com
Websaịtị: www.epever.com

Akwụkwọ / akụrụngwa

EPEVER EPIPDB-COM-10 Onye njikwa chaja PWM Batrị abụọ [pdf] Akwụkwọ ntuziaka onye ọrụ EPIPDB-COM-10, EPIPDB-COM-20, EPIPDB-COM-10 Batrị abụọ PWM njikwa chaja, EPIPDB-COM-10, Batrị abụọ PWM njikwa chaja, batrị PWM njikwa chaja, PWM njikwa chaja, njikwa chaja.

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ