Mgbanwe ịdị nso maka njikwa ọrụ yana njikwa nnweta
“
Ozi ngwaahịa
Nkọwapụta:
- Mgbanwe nso maka ịgbalite na njikwa ohere
- Ihe mkpuchi siri ike, na-eguzogide ọkọ, mgbochi ntụgharị, mgbochi microbial
Steritouch acrylic labelụ - Labelụ niile nwere mmetụta
- Oge Radio: 868MHz
- Power Supply: 4 x AA batteries for the unit, 12/24Vdc for the
onye nnata - Approximately 100,000 operations battery life
- Dimensions: Unit – (specific dimensions not provided), Receiver
- 65 x 50 x 30 mm
Ntuziaka ojiji ngwaahịa
Nwụnye:
- Ascertain the fixing height.
- Use the back plate to mark cable hole and screw fixing
isi. - Fix the top retaining screw (No 8 or 10) leaving 4mm of screw
shaft protruding. - Fit the back seal to the rear of back plate (if being installed
externally). - Place the cable through back plate and make connections or
connect battery clip and program to receiver. - Place the back plate in position, hook unit onto the top
retaining screw and fit the bottom retaining screw.
Eserese waya:
Refer to the provided wiring diagrams for hardwired sensor
wiring and alter LED color configuration as required.
Radio Programming (RX-2):
- Supply receiver with 12/24Vdc power.
- Wire relay outputs to activate terminals on the system (clean,
normally open contacts). - Press and release the learn button, then operate the touch
sensor within 15 seconds to program it. - To reset the receiver, press and hold the learn button for 10
seconds until the learn LED starts flashing.
FAQ
Ajụjụ: Kedu ka m ga-esi tọgharịa onye nnata?
A: Iji tọgharịa onye nnata, pịa ma jide bọtịnụ mmụta maka 10
sekọnd ruo mgbe ịmụta Ikanam amalite na-egbu maramara. Mgbe nke a gasịrị, ebe nchekwa
ga-ehichapụ.
Q: What is the approximate battery life of the unit?
A: The unit has an approximate battery life of 100,000
arụmọrụ.
"'
Nwụnye:
ARCHITRAVE & ROUND Manual
Mgbanwe nso maka ịgbalite na njikwa ohere
Ihe mkpuchi siri ike, ọkọ na-eguzogide, mgbochi ntụgharị, mgbochi microbial Steritouch acrylic labelụ Labelụ niile nwere mmetụta www.quantek.co.uk 01246 417113
Ascertain the fixing height.
Use the back plate to mark cable hole and screw fixing points, round unit can be angled towards approaching users.
Fix the top retaining screw (No 8 or 10) leaving 4mm of screw shaft protruding.
Tinye akara azụ n'azụ efere azụ (ọ bụrụ na etinyere ya na mpụga)
Place the cable through back plate and make connections (see below) or connect battery clip and program to receiver (see next page).
Place the back plate in position, hook unit onto the top retaining screw and fit the bottom retaining screw.
Hardwired specification: 12 28v dc 8mA (standby) / 35mA (max) +18mA LEDs Sensitivity – Touch – up to 70mm hands free Selectable red, green, blue LEDs Sounder on activation Timer 1 – 27 seconds Latching function
Architrave Round
Eserese waya
Wiring ihe mmetụta siri ike. Gbanwee nhazi agba LED ka achọrọ.
Na-emepe kọntaktị na-emekarị. 0v laghachi
12-28Vdc Ọ DỊ ọrụ
0V laghachi 0V
Latch jumper nwa oge Latching
Na-emepe kọntaktị na-emekarị. +v laghachi
12-28Vdc Ọ DỊ ọrụ
+ V nloghachi 0V
Mgbanwe dịpụrụ adịpụ
Mba (Nhọrọ)
Mgbanwe mgbanwe mmetụta uche
1 – Ala 4 – Elu Wepụ ike mgbanwe nso re ike
Ụda
Ngụ oge
1-27 sekọnd megidere elekere ka iwelie oge
Mara: Ejikọtala ihe ọ bụla na ọdụ RD
Radio programming (RX-2)
Onye nnata ihe nwere ike 12/24Vdc. + V ruo 12/24V ọnụ, -V ruo ọnụ GND. LED ga-enwu ma ọ bụrụ na agbanyere ya nke ọma
Nsonaazụ relay waya iji rụọ ọrụ ọnụ na sistemụ (dị ọcha, kọntaktị na-emeghe na-emekarị)
Pịa ma hapụ bọtịnụ mmụta, LED mmụta ga-enwu maka sekọnd 15
N'ime sekọnd iri rụọ ọrụ ihe mmetụta
The learn LED ga-flash iji gosi na ọ programmed Cheta na: Touch sensọ omume na ọwa 1. The RX-T nnata ga-achọrọ ma ọ bụrụ na ị chọrọ mmemme ha na dị iche iche ọwa. Ọ ga-ekwe omume iji usoro a na-ebufe ihe ejiri aka na desk mount (CFOB, FOB1-M, FOB2-M, FOB2-MS, FOB4-M, FOB4-MS, DDA1, DDA2) banye n'ime nnabata a. Lee igbe nnyefe maka nkọwa ndị ọzọ.
Tọgharia: Iji tọgharịa onye nnata, pịa ma jide bọtịnụ mmụta maka sekọnd 10 ruo mgbe mmụta LED ga-amalite na-egbuke egbuke. Mgbe nke a gasịrị, a ga-ehichapụ ebe nchekwa ahụ
Nkọwapụta redio
868MHz 4 x AA batteries Approximately 100,000 operations Sounder & green LED on activation Battery saving design, unit will only activate once if hand left on
Nkọwa nke nnata
12/24Vdc ọkọnọ 868MHz 2 ọwa 1A 24Vdc na-emeghe kọntaktsị nwa oge/bi-stable selectable relays 200 code memory Akụkụ: 65 x 50 x 30 mm
Ntọala Dipswitch
ON
Gbanyụọ
1
CH1 - Bi-Stable
CH1 - nwa oge
2
CH2 - Bi-Stable
CH2 - nwa oge
Vidiyo mmemme
Akwụkwọ / akụrụngwa
 |
Quantek Proximity Switch For Activation and Access Control [pdf] Ntuziaka TS-A-R, TS SQ, Proximity Switch For Activation and Access Control, Switch For Activation and Access Control, Activation and Access Control, and Access Control, Access Control |