Entèriptè pwoksimite pou aktivasyon ak kontwòl aksè
“
Enfòmasyon sou pwodwi
Espesifikasyon:
- Bouton pwoksimite pou deklanchman ak kontwòl aksè
- Hard coated, scratch resistant, anti-reflective, anti-microbial
Steritouch acrylic label - Entire label is sensitive
- Frekans radyo: 868MHz
- Power Supply: 4 x AA batteries for the unit, 12/24Vdc for the
reseptè - Approximately 100,000 operations battery life
- Dimensions: Unit – (specific dimensions not provided), Receiver
- 65 x 50 x 30 mm
Enstriksyon Itilizasyon Pwodwi
Enstalasyon:
- Ascertain the fixing height.
- Use the back plate to mark cable hole and screw fixing
pwen. - Fix the top retaining screw (No 8 or 10) leaving 4mm of screw
shaft protruding. - Fit the back seal to the rear of back plate (if being installed
externally). - Place the cable through back plate and make connections or
connect battery clip and program to receiver. - Place the back plate in position, hook unit onto the top
retaining screw and fit the bottom retaining screw.
Dyagram fil elektrik:
Refer to the provided wiring diagrams for hardwired sensor
wiring and alter LED color configuration as required.
Radio Programming (RX-2):
- Supply receiver with 12/24Vdc power.
- Wire relay outputs to activate terminals on the system (clean,
normally open contacts). - Press and release the learn button, then operate the touch
sensor within 15 seconds to program it. - To reset the receiver, press and hold the learn button for 10
seconds until the learn LED starts flashing.
FAQ
K: Kijan pou m retabli reseptè a?
A: To reset the receiver, press and hold the learn button for 10
seconds until the learn LED starts flashing. After this, the memory
pral efase.
Q: What is the approximate battery life of the unit?
A: The unit has an approximate battery life of 100,000
operasyon yo.
"`
Enstalasyon:
ARCHITRAVE & ROUND Manual
Bouton pwoksimite pou deklanchman ak kontwòl aksè
Hard coated, scratch resistant, anti-reflective, anti-microbial Steritouch acrylic label Entire label is sensitive www.quantek.co.uk 01246 417113
Ascertain the fixing height.
Use the back plate to mark cable hole and screw fixing points, round unit can be angled towards approaching users.
Fix the top retaining screw (No 8 or 10) leaving 4mm of screw shaft protruding.
Mete sele dèyè a nan dèyè plak dèyè (si yo enstale deyò)
Place the cable through back plate and make connections (see below) or connect battery clip and program to receiver (see next page).
Place the back plate in position, hook unit onto the top retaining screw and fit the bottom retaining screw.
Hardwired specification: 12 28v dc 8mA (standby) / 35mA (max) +18mA LEDs Sensitivity – Touch – up to 70mm hands free Selectable red, green, blue LEDs Sounder on activation Timer 1 – 27 seconds Latching function
Architrave Round
Dyagram fil elektrik
Fil elektrik fil elektrik. Chanje konfigirasyon koulè dirije jan sa nesesè.
Normally open contacts. 0v return
12-28Vdc NO activate
0V return 0V
Latch jumper Momentary Latching
Normally open contacts. +v return
12-28Vdc NO activate
+V return 0V
Remote switch
N.O. (Optional)
Sensitivity dip-switches
1 – Low 4 – High Remove power alter range re power
Sonè
Revèy
1-27 seconds Anti-clockwise to increase time
Remak: Pa janm konekte anyen nan tèminal RD
Radio programming (RX-2)
Supply receiver with 12/24Vdc power. +V to 12/24V terminal, -V to GND terminal. LED will light if powered correctly
Sorti relè fil yo aktive tèminal sou sistèm lan (kontak pwòp, nòmalman louvri)
Peze epi lage bouton aprann la, dirije aprann ap limen pou 15 segonn
Nan 15 segonn yo opere Capteur manyen la
The learn LED will flash to confirm it has programmed Note: Touch sensors program to channel 1. The RX-T receiver will be required if you need to program them to different channels. It is also possible to program our handheld and desk mount transmitters (CFOB, FOB1-M, FOB2-M, FOB2-MS, FOB4- M, FOB4-MS, DDA1, DDA2) into this receiver using the same method. See transmitter box for more details.
Reyajiste: Pou reset reseptè a, peze epi kenbe bouton aprann la pou 10 segonn jiskaske dirije aprann nan kòmanse flache. Apre sa, memwa a pral efase
spesifikasyon radyo
868MHz 4 x AA batteries Approximately 100,000 operations Sounder & green LED on activation Battery saving design, unit will only activate once if hand left on
Spesifikasyon reseptè
12/24Vdc supply 868MHz 2 channels 1A 24Vdc normally open contacts Momentary/bi-stable selectable relays 200 code memory Dimensions: 65 x 50 x 30 mm
Anviwònman Dipswitch
ON
OFF
1
CH1 - Bi-estab
CH1 – Momantan
2
CH2 - Bi-estab
CH2 – Momantan
Programming video
Dokiman / Resous
 |
Quantek Proximity Switch For Activation and Access Control [pdfEnstriksyon yo TS-A-R, TS SQ, Proximity Switch For Activation and Access Control, Switch For Activation and Access Control, Activation and Access Control, and Access Control, Access Control |