ARDUINO ABX00049 Core Electronics Module
Nkọwa
Arduino® Portenta X8 bụ kọmpụta otu bọọdụ arụ ọrụ dị elu emebere iji mee ka ọgbọ Internetntanetị nke ihe na-abịa. Bọọdụ a na-ejikọta NXP® i.MX 8M Mini na-anabata Linux OS agbakwunyere na STM32H7 iji nweta ọba akwụkwọ / nka Arduino. Ọta na mbadamba ihe dị ka ịgbatị arụmọrụ nke X8 ma ọ bụ n'ụzọ ọzọ enwere ike iji ya dị ka atụmatụ ntụaka iji mepụta ngwọta omenala nke gị.
Mpaghara ebumnuche
Kọmputa Edge, ịntanetị ihe nrụpụta ihe, kọmpụta otu bọọdụ, ọgụgụ isi
Atụmatụ
| Akụkụ | Nkọwa | |
| NXP® i.MX 8M
Obere Nhazi |
4x Arm® Cortex®-A53 isi nyiwe ruo 1.8 GHz kwa isi. |
32KB L1-I Cache 32kB L1-D Cache 512kB L2 Cache |
| Arm® Cortex®-M4 isi ruo 400 MHz | 16 kB L1-I Cache 16 kB L2-D Cache | |
| 3D GPU (1x shader, OpenGL® ES 2.0) | ||
| GPU 2D | ||
| 1x MIPI DSI (ụzọ anọ) nwere PHY | ||
| 1080p60 VP9 Profaịlụ 0, 2 (10-bit) ihe ndozi, HEVC/H.265 decoder, AVC/H.264 Baseline, Main, High decoder, VP8 decoder | ||
| 1080p60 AVC/H.264 mkpuchi, VP8 mkpuchi | ||
| 5x SAI (12Tx + 16Rx mpụga I2S ụzọ), ntinye 8ch PDM | ||
| 1x MIPI CSI (ụzọ anọ) nwere PHY | ||
| 2x USB 2.0 OTG njikwa nwere PHY agbakwunyere | ||
| 1x PCIe 2.0 (1-lane) nwere obere ala L1 dị ala | ||
| 1 x Gigabit Ethernet (MAC) nwere AVB na IEEE 1588, ike na-arụ ọrụ nke ọma (EEE) maka ike dị ala. | ||
| 4x UART (5mbps) | ||
| 4 x I2C | ||
| 3 x SPI | ||
| 4 x PWM | ||
| STM32H747XI
Microcontroller |
Arm® Cortex®-M7 isi ruo 480 MHz nwere FPU nkenke. | 16K data + 16K ntụziaka L1 cache |
| 1x Arm® 32-bit Cortex®-M4 isi ruo 240 MHz nwere FPU, ihe na-eme ngwa ngwa ozugbo (ART Accelerator ™) | ||
| Ebe nchekwa | 2 MB nke ebe nchekwa Flash nwere nkwado ọgụgụ mgbe-dere
1 MB nke RAM |
|
| Ebe nchekwa dị | NT6AN512T32AV | 2GB DDR4 DRAM dị ala |
| FEMDRW016G | 16GB Foresee® eMMC Flash modul | |
| USB-C | Ọsọ USB dị elu | |
| Mmepụta DisplayPort | ||
| Ọrụ onye ọbịa na ngwaọrụ | ||
| Nkwado nnyefe ike | ||
| Akụkụ | Nkọwa | |
| Elu Njikọ njupụta | 1 uzo PCI Express | |
| 1x 10/100/1000 Ethernet interface nwere PHY | ||
| 2 x USB HS | ||
| 4x UART (2 nwere njikwa mmiri) | ||
| 3 x I2C | ||
| 1 x kaadị SD interface | ||
| 2x SPI (1 kesara ya na UART) | ||
| 1 x I2S | ||
| 1 x PDM ntinye | ||
| 4 uzo MIPI DSI mmepụta | ||
| 4 uzo MIPI CSI ntinye | ||
| 4x PWM mmepụta | ||
| 7x GPIO | ||
| Ntinye 8x ADC nwere VREF dị iche | ||
| Murata® 1DX Wi-Fi®/Bluetooth® Module | Wi-Fi® 802.11b/g/n 65Mbps | |
| Bluetooth® 5.1 BR/EDR/LE | ||
| NXP® SE050C2
Crypto |
Asambodo a na-ahụkarị EAL 6+ enwetara asambodo ruo ọkwa OS | |
| RSA & ECC arụ ọrụ, ogologo igodo dị elu na akụkụ mgbanaka n'ọdịnihu, dị ka brainpool, Edwards, na Montgomery | ||
| AES & 3DES izo ya ezo na decryption | ||
| HMAC, CMAC, SHA-1, SHA-224/256/384/512
arụmọrụ |
||
| HKDF, MIFARE® KDF, PRF (TLS-PSK) | ||
| Nkwado nke isi ọrụ TPM | ||
| Ebe nchekwa flash ejiri echekwara ruo 50kB | ||
| Ohu I2C (Ụdị ọsọ dị elu, 3.4Mbit/s), I2C nna ukwu (Ọsọ ọsọ, 400 kbit/s) | ||
| SCP03 (njikwa ụgbọ ala na ntinye nzere ezoro ezo na ọkwa applet na ikpo okwu) | ||
| TI ADS7959SRGET | 12 bit, 1 MSPS, 8 Ch, Otu gwụchara, Ike Micro, SAR ADC | |
| Abụọ SW Họrọ Unipolar, Ntinye ntinye: 0 ruo VREF na 0 ruo 2 x VREF | ||
| Ụdị akpaaka na akwụkwọ ntuziaka maka nhọrọ ọwa | ||
| Ọkwa mkpu abụọ enwere ike ime kwa ọwa | ||
| Ike-ala ugbu a (1 µA) | ||
| Bandwit ntinye (47 MHz na 3 dB) | ||
| NXP® PCF8563BS | Obere ike Real Time elekere | |
| Na-enye ọkọlọtọ Century, afọ, ọnwa, ụbọchị, ụbọchị izu, awa, nkeji na sekọnd | ||
| Obere ndabere ugbu a; ụdị 250 nA na VDD = 3.0 V na Tamb = 25°C | ||
| Akụkụ | Nkọwa | |
| RoHM BD71847AMWV
PMIC nwere ike ime |
Dị ike voltage scaling | |
| 3.3V/2A voltage mmepụta na osisi ụgbọelu | ||
| Oke okpomọkụ | -40°C ruo +85°C | Ọ bụ naanị ọrụ dịịrị onye ọrụ ịnwale ọrụ bọọdụ na oke okpomọkụ zuru oke |
| Ozi nchekwa | Klas A | |
Ngwa Examples
Emebere Arduino® Portenta X8 maka ngwa mgbako agbakwunyere arụmọrụ dị elu n'uche, dabere na quad core NXP® i.MX 8M Mini Processor. Ụdị ụdị Portenta na-enyere aka iji ọtụtụ ọta gbasaa n'ọrụ ya.
- Linux agbakwunyere: Bido ibuga ụlọ ọrụ 4.0 site na ngwugwu nkwado Linux Board na-agba ọsọ na njirimara juru ebe niile yana ike siri ike Arduino® Portenta X8. Jiri ngwa GNU mepụta ihe ngwọta gị n'enweghị mkpọchi teknụzụ.
- Netwọk arụmọrụ dị elu: Arduino® Portenta X8 gụnyere Wi-Fi® na njikọ Bluetooth® iji mekọrịta ngwaọrụ dị iche iche nke mpụga yana netwọk na-enye mgbanwe dị elu. Na mgbakwunye, Gigabit Ethernet interface na-enye oke ọsọ yana obere latency maka ngwa kachasị achọ.
- Mmepe agbakwunyere modular dị elu: The Arduino® Portenta X8 bụ nnukwu ngalaba maka ịmepụta ọtụtụ ụdị ngwọta omenala. Njikọ njupụta dị elu na-enye ohere ịnweta ọtụtụ ọrụ, gụnyere njikọ PCIe, CAN, SAI na MIPI. N'aka nke ọzọ, jiri gburugburu Arduino nke bọọdụ emebere nke ọma dị ka ntụaka maka atụmatụ nke gị. Akpa sọftụwia dị ala na-enye ohere ibugharị ngwa ngwa.
Ngwa ngwa
- Ogwe USB-C
- USB-C ka HDMI nkwụnye
Ngwaahịa ndị emetụtara
- Arduino® Portenta Breakout Board (ASX00031)
Ọnọdụ ọrụ akwadoro
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| VIN | Ntinye voltage sitere na VIN pad | 4.5 | 5 | 5.5 | V |
| VUSB | Ntinye voltage site na njikọ USB | 4.5 | 5 | 5.5 | V |
| V3V3 | 3.3 V mmepụta na ngwa onye ọrụ | 3.1 | V | ||
| I3V3 | 3.3 V mmepụta ugbu a dị maka ngwa onye ọrụ | – | – | 1000 | mA |
| VIH | Tinye ọkwa dị elu voltage | 2.31 | – | 3.3 | V |
| VIL | Tinye obere ọkwa voltage | 0 | – | 0.99 | V |
| Ọnụ ego nke IOH Max | Ugbu a na VDD-0.4 V, mmepụta setịpụrụ elu | 8 | mA | ||
| IOL Max | Ugbu a na VSS+0.4 V, ewepụtarala ihe nrụpụta dị ala | 8 | mA | ||
| VOH | Mmepụta elu voltage, 8mA | 2.7 | – | 3.3 | V |
| VOL | Mmepụta obere voltage, 8mA | 0 | – | 0.4 | V |
Oriri ike
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| PBL | Oriri ike na akaghị aka | 2350 | mW | ||
| PLP | Oriri ike na ọnọdụ ike dị ala | 200 | mW | ||
| PMAX | Oriri ike kacha | 4000 | mW |
A na-atụ aro ka iji ọdụ ụgbọ mmiri USB 3.0 mgbe ị na-ejikọta na Portenta X8 nke nwere ike ịnapụta ike achọrọ. Ntụle dị egwu nke Portenta X8 nwere ike ịgbanwe oriri ugbu a, na-eduga na mgbawa ugbu a n'oge bootup. A na-enye nkezi oriri ike na tebụl dị n'elu maka ọtụtụ ọnọdụ ntụaka.
Ihe Ngosi
Board Topology
N'ihu View
| Ref. | Nkọwa | Ref. | Nkọwa |
| U1 | BD71847AMWV i.MX 8M Obere PMIC | U2 | MIMX8MM6CVTKZAA i.MX 8M Obere Quad IC |
| U4 | NCP383LMUAJAATXG Ngbanwe ike na-amachi ugbu a | U6 | ANX7625 MIPI-DSI/DPI ka USB Ụdị-C™ akwa IC |
| U7 | MP28210 Kwụpụ ala IC | U9 | LBEE5KL1DX-883 WLAN+Bluetooth® Combo IC |
| U12 | PCMF2USB3B/CZ Bidirectional EMI Nchedo IC | U16,U21,U22,U23 | FXL4TD245UMX 4-Bit Bidirectional Voltage- larịị Ntụgharị IC |
| U17 | DSC6151HI2B 25MHz MEMS Oscillator | U18 | DSC6151HI2B 27MHz MEMS Oscillator |
| U19 | NT6AN512T32AV 2GB LP-DDR4 DRAM | IC1, IC2, IC3, IC4 | SN74LVC1G125DCKR 3-steeti 1.65-V ruo 5.5-V bufee IC |
| PB1 | PTS820J25KSMTRLFS Tọgharia bọtịnụ | Dl1 | KPHHS-1005SURCK Ike Na SMD LED |
| DL2 | SMLP34RGB2W3 RGB nkịtị Anode SMD LED | Y1 | CX3225GB24000P0HPQCC 24MHz kristal |
| Y3 | DSC2311KI2-R0012 Mmepụta MEMS Oscillator Dual | J3 | CX90B1-24P USB Ụdị-C njikọ |
| J4 | U.FL-R-SMT-1(60) Njikọ UFL |
Azu View
| Ref. | Nkọwa | Ref. | Nkọwa |
| U3 | LM66100DCKR ezigbo diode | U5 | FEMDRW016G 16GB eMMC Flash IC |
| U8 | KSZ9031RNXIA Gigabit Ethernet Transceiver IC | U10 | FXMA2102L8X Nnweta Dual, 2-Bit Voltage Translator IC |
| U11 | Ihe nchekwa SE050C2HQ1/Z01SDZ IoT | U12, U13, U14 | PCMF2USB3B/CZ Bidirectional EMI Nchedo IC |
| U15 | NX18P3001UKZ Bidirectional ike mgba ọkụ IC | U20 | STM32H747AII6 Dual ARM® Cortex® M7/M4 IC |
| Y2 | SIT1532AI-J4-DCC-32.768E 32.768KHz MEMS Oscillator IC | NKWO, J1 | Njikọ njupụta dị elu |
| Q1 | 2N7002T-7-F N-Channel 60V 115mA MOSFET |
Nhazi
Arduino Portenta X8 na-eji nkeji nhazi anụ ahụ dabere na ARM abụọ.
NXP® i.MX 8M Obere Quad isi Microprocessor
MIMX8MM6CVTKZAA iMX8M (U2) nwere quad core ARM® Cortex® A53 na-agba ọsọ ruo 1.8 GHz maka ngwa arụmọrụ dị elu n'akụkụ ARM® Cortex® M4 na-agba ọsọ ruo 400 MHz. ARM® Cortex® A53 nwere ike iji sistemụ arụmọrụ Linux ma ọ bụ gam akporo gam akporo site na ngwugwu nkwado Board (BSP) n'ụdị nwere ọtụtụ eriri. Enwere ike ịgbasa nke a site na iji ngwa ngwa pụrụ iche site na mmelite OTA. ARM® Cortex® M4 nwere obere ike oriri na-enye ohere maka njikwa ihi ụra nke ọma yana ịrụ ọrụ kacha mma na ngwa ozugbo ma echekwara ya maka ojiji n'ọdịnihu. Ndị nhazi abụọ ahụ nwere ike kesaa akụkụ na akụrụngwa niile dị na i.MX 8M Obere, gụnyere PCIe, ebe nchekwa on-chip, GPIO, GPU na Audio.
STM32 Dual Core Microprocessor
X8 gụnyere H7 agbakwunyere n'ụdị STM32H747AII6 IC (U20) nwere isi ARM® Cortex® M7 na ARM® Cortex® M4. A na-eji IC a dị ka onye na-agbasawanye I/O maka NXP® i.MX 8M Mini (U2). A na-achịkwa ihe ndị ọzọ na-akpaghị aka site na isi M7. Na mgbakwunye, isi M4 dị maka njikwa oge nke moto na igwe ndị ọzọ dị oke egwu na ọkwa ọkpụkpụ. Isi M7 na-arụ ọrụ dị ka onye ogbugbo n'etiti mpụta na i.MX 8M Obere ma na-arụ firmware nwe nke enweghị ike ịnweta onye ọrụ. A naghị ekpughe STM32H7 na ịkparịta ụka n'Ịntanet na ekwesịrị ịhazi ya site na i.MX 8M Mini (U2).
Njikọ Wi-Fi®/Bluetooth®
Igwe ikuku Murata® LBEE5KL1DX-883 (U9) na-enye njikọ Wi-Fi® na Bluetooth® n'otu oge n'ime obere ngwugwu dabere na Cypress CYW4343W. Enwere ike ịrụ ọrụ IEEE802.11b/g/n Wi-Fi® interface dị ka ebe nnweta (AP), ọdụ (STA) ma ọ bụ dị ka ọnọdụ abụọ n'otu oge AP/STA ma na-akwado ọnụego mbufe kacha nke 65 Mbps. Bluetooth® interface na-akwado Bluetooth® Classic na Bluetooth® obere ike. Mgba ọkụ sekit antenna agbakwunyere na-enye ohere ịkekọrịta otu antenna mpụga (J4 ma ọ bụ ANT1) n'etiti Wi-Fi® na Bluetooth®. Modul U9 interfaces nwere i.MX 8M Mini (U2) site na 4bit SDIO na UART interface. Dabere na ngwugwu ngwanrọ nke modul ikuku na Linux OS agbakwunyere, a na-akwado Bluetooth® 5.1 yana Wi-Fi® kwekọrọ na ọkọlọtọ IEEE802.11b/g/n.
Ncheta onboard
Arduino® Portenta X8 gụnyere modul ebe nchekwa ihe abụọ. A NT6AN512T32AV 2GB LP-DDR4 DRAM (U19) na 16GB Forsee eMMC Flash modul (FEMDRW016G) (U5) na-enweta na i.MX 8M Mini (U2).
Ike Crypto
The Arduino® Portenta X8 na-enyere IC larịị ihu-na-igwe nchekwa ikike site NXP® SE050C2 Crypto mgbawa (U11). Nke a na-enye asambodo nchekwa EAL 6+ nkịtị ruo ọkwa OS, yana nkwado RSA/ECC cryptographic algọridim yana nchekwa nzere. Ọ na-emekọrịta ihe na NXP® i.MX 8M Mini site na I2C.
Gigabit Ethernet
The NXP® i.MX 8M Mini Quad na-agụnye 10/100/1000 Ethernet njikwa na nkwado maka Energy E-Ethernet (EEE), Ethernet AVB, na IEEE 1588. A chọrọ njikọ anụ ahụ dị n'èzí iji mezue interface ahụ. Enwere ike ịnweta nke a site na njikọ njupụta dị elu nwere akụrụngwa dị na mpụga dịka bọọdụ Arduino® Portenta Breakout.
USB-C njikọ
Njikọ USB-C na-enye ọtụtụ nhọrọ njikọ karịa otu interface anụ ahụ:
- Nyenye ọkụ bọọdụ na ọnọdụ DFP na DRP
- Ike isi mmalite na mpụga mpụta mgbe agbanyere bọọdụ site na VIN
- Kpochapụ ọsọ ọsọ (480 Mbps) ma ọ bụ ọsọ zuru oke (12 Mbps) USB onye ọbịa / ngwaọrụ
- Expose Displayport mmepụta interface A na-eji interface Displayport eme ihe na njikọ USB ma enwere ike iji ya na eriri eriri USB dị mfe mgbe ejiri VIN kwadoro osisi ma ọ bụ na dongles nwere ike inye ike na bọọdụ ka ọ na-emepụta ihe ngosi na USB n'otu oge. Dongle ndị dị otú ahụ na-enyekarị ethernet n'elu ọdụ ụgbọ mmiri USB, ọdụ ụgbọ mmiri USB 2 na ọdụ USB-C nke enwere ike iji nye ike na sistemụ.
Ezigbo Oge elekere
The Real Time elekere na-enye ohere idobe oge nke ụbọchị na ike dị nnọọ ala.
Osisi Ike
Ọrụ Board
- Mmalite – IDE
Ọ bụrụ na ịchọrọ ịme mmemme Arduino® Portenta X8 gị mgbe ị na-anọghị, ịkwesịrị ịwụnye Arduino® IDE Desktop [1] Iji jikọọ njikwa Arduino® Edge na kọmputa gị, ị ga-achọ eriri USB Type-c. Nke a na-enyekwa ike na osisi ahụ, dị ka LED gosipụtara. - Mmalite – Arduino Web Onye nchịkọta akụkọ
Bọọdụ Arduino® niile, gụnyere nke a, na-arụ ọrụ nke ọma na Arduino® Web Editor [2], site na ịwụnye ngwa mgbakwunye dị mfe. Arduino® Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro [3] ka ịmalite itinye koodu na ihe nchọgharị wee bulite ihe osise gị na bọọdụ gị. - Mmalite – Arduino IoT Cloud
A na-akwado ngwaahịa Arduino® IoT niile na Arduino® IoT Cloud nke na-enye gị ohere ịbanye, eserese na nyochaa data ihe mmetụta, kpalite ihe omume, wee rụzie ụlọ ma ọ bụ azụmahịa gị. - Sampna Sketches
SampEnwere ike ịhụ sketị maka Arduino® Portenta X8 ma na “Examples” menu na Arduino® IDE ma ọ bụ na ngalaba “akwụkwọ” nke Arduino Pro websaịtị [4] - Ngwa ntanetị
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ na-akpali akpali na ProjectHub [5], Arduino® Library Reference [6] na ụlọ ahịa dị n'ịntanetị [7] ebe. ị ga-enwe ike iji sensọ, actuators na ndị ọzọ mejuo osisi gị. - Iweghachite Board
Bọdụ Arduino niile nwere ihe nrụnye bootloader nke na-enye ohere iji eriri USB na-ebunye bọọdụ ahụ. Ọ bụrụ na eserese kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB, ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo ọ gbasịrị.
Ozi igwe
Pinout
Ngwunye oghere na ihe ngosi osisi
Asambodo
| Asambodo | Nkọwa |
| CE (EU) | EN 301489-1
EN 301489-1 EN 300328 EN 62368-1 EN 62311 |
| WEEE (EU) | Ee |
| RoHS (EU) | 2011/65/(EU)
2015/863/(EU) |
| IHE (EU) | Ee |
| UKCA (UK) | Ee |
| RCM (RCM) | Ee |
| FCC (US) | NJ.
Radio: Akụkụ 15.247 MPE: Akụkụ 2.1091 |
| RCM (AU) | Ee |
Nkwupụta nke Nkwekọrịta CE DoC (EU)
Anyị na-ekwupụta n'okpuru ọrụ anyị naanị na ngwaahịa ndị dị n'elu kwekọrọ na ihe ndị dị mkpa nke ntuziaka EU na-esote ya mere tozuru oke maka mmegharị n'efu n'ime ahịa nke nwere European Union (EU) na European Economic Area (EEA).
Nkwupụta nke Nkwekọrịta na EU RoHS & REACH 21101/19/2021
bọọdụ Arduino kwekọrọ na RoHS 2 Directive 2011/65/EU nke European nzuko omeiwu na RoHS 3 Directive 2015/863/EU nke Council of 4 June 2015 na mmachi nke ojiji nke ụfọdụ ize ndụ ihe na ngwa eletriki na eletrọnịkị.
| Ihe | Oke kacha (ppm) |
| Ndu (Pb) | 1000 |
| Ogwugwu (Cd) | 100 |
| Ebere (Hg) | 1000 |
| Chromium Hexavalent (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Mwepu: Enweghị mwepu a na-ekwu.
Boards Arduino na-akwado nke ọma na ihe ndị metụtara European Union Regulation (EC) 1907/2006 gbasara ndebanye aha, nyocha, ikike na mmachi nke kemịkalụ (REACH). Anyị na-ekwupụta na ọ nweghị nke SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), Ndepụta ndị Candidate nke ihe dị oke mkpa maka ikike nke ECHA wepụtara ugbu a, dị na ngwaahịa niile (yana ngwugwu) n'ogo zuru oke na mkpokọta nha ma ọ bụ karịa 0.1%. Dị ka ihe ọmụma anyị si mara, anyị na-ekwupụtakwa na ngwaahịa anyị enweghị ihe ọ bụla e depụtara na "Ndepụta ikike" (Annex XIV nke ụkpụrụ REACH) na ihe gbasara nchegbu dị oke elu (SVHC) n'ụdị ọ bụla dị mkpa dị ka akọwapụtara. site na Mgbakwunye XVII nke ndepụta Candidate bipụtara EHA (European Chemical Agency) 1907/2006/EC.
Nkwupụta mineral esemokwu
Dị ka onye na-eweta ihe elektrọnik na eletriki eletrik zuru ụwa ọnụ, Arduino maara ọrụ anyị na-ahụ maka iwu na ụkpụrụ gbasara Mineral Conflict, kpọmkwem Dodd-Frank Wall Street Reform and Consumer Protection Act, Nkebi 1502. Arduino anaghị ebute ma ọ bụ hazie esemokwu ozugbo. mineral dị ka Tin, Tantalum, Tungsten, ma ọ bụ ọla edo. Ngwakọta mineral ndị na-ese okwu dị n'ime ngwaahịa anyị n'ụdị ihe na-ere ahịa, ma ọ bụ dị ka akụrụngwa na alloys ọla. Dịka akụkụ nke mbọ anyị kwesịrị ekwesị Arduino akpọtụrụla ndị na-ebubata akụrụngwa n'ime ụdọ ọkọnọ anyị iji chọpụta na ha nọgidere na-agbaso ụkpụrụ ahụ. Dabere na ozi enwetara ugbu a, anyị na-ekwupụta na ngwaahịa anyị nwere Mineral Conflict sitere na mpaghara enweghị nsogbu.
FCC ịkpachara anya
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị otu na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ngwa ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Nkwupụta Mkpughe Radiation FCC RF:
- Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
- Ngwa a na-akwado oke mkpughe radieshon RF ewepụtara maka gburugburu enweghị njikwa.
- Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na anya kacha nta 20cm n'etiti radiator & ahụ gị.
Akwụkwọ ntuziaka onye ọrụ maka ngwa redio enweghị ikike ga-enwe ọkwa ndị a ma ọ bụ nha nhata na ọnọdụ pụtara ìhè n'ime akwụkwọ ntuziaka onye ọrụ ma ọ bụ ọzọ na ngwaọrụ ma ọ bụ ha abụọ. Ngwaọrụ a na-akwado ụkpụrụ RSS enweghị ikike ụlọ ọrụ Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ọrụ ngwaọrụ ahụ achọghị.
Ịdọ aka ná ntị IC SAR:
Asụsụ a kwesịrị ịwụnye ma rụọ ọrụ ya na anya kacha nta 20 cm n'etiti radiator na ahụ gị.
Ihe dị mkpa: Ọnọdụ okpomọkụ nke EUT enweghị ike ịgafe 85 ℃ ma ghara ịdị ala karịa -40 ℃.
N'ihi nke a, Arduino Srl na-ekwupụta na ngwaahịa a kwekọrọ na ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 201453/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
| Ugboro ugboro | Ike mmepụta kacha (ERP) |
| 2.4 GHz, 40 ọwa | + 6dBm |
Ozi ụlọ ọrụ
| Aha Ụlọ Ọrụ | Arduino SRL |
| Adreesị ụlọ ọrụ | Site na Andrea Appiani 25, 20900, MONZA MB, Italy |
Akwụkwọ ntụaka
| Ref | Njikọ |
| Arduino IDE (Desktọpụ) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (igwe ojii) | https://create.arduino.cc/editor |
| Cloud IDE na-amalite | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino- web-editor-4b3e4a |
| Arduino Pro Websaịtị | https://www.arduino.cc/pro |
| Hub Project | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Ntụaka ụlọ akwụkwọ | https://github.com/arduino-libraries/ |
| Ụlọ ahịa dị n'ịntanetị | https://store.arduino.cc/ |
Gbanwee Ndekọ
| Ụbọchị | Mgbanwe |
| 24/03/2022 | Hapụ |
Akwụkwọ / akụrụngwa
 |
ARDUINO ABX00049 Core Electronics Module [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00049 Core Electronics Module, ABX00049, Core Elektrọnịkị Module, Eletrọnịkị Module, Modul |
