StrikeIt1V
Mai Kula da Wutar Lantarki na Na'urar tsoro
Jagoran Shigarwa

Ƙarsheview:

Altronix StrikeIt 1V zai yi aiki har zuwa biyu (2) 24VDC na'urorin kayan tsoro a lokaci guda. An ƙirƙira shi don kula da buƙatar na'urorin kulle firgici mai girma na yanzu. Kowane fitarwa na kulle yana da daidaitacce mai ƙidayar jinkiri. Zai sarrafa kofofi guda biyu a lokaci guda ko sarrafa kofofin guda biyu daban-daban. Yana da na'ura mai bibiya don kowane fitarwa don kunna relays na waje, ADA tura faranti, da dai sauransu.
Bugu da kari, biyu un-switched auxiliary voltagAna samar da abubuwan da ake fitarwa don masu karanta katin, maɓalli, REX PIRs, na'urorin lantarki, relays, da dai sauransu. Fayil ɗin FACP mai daidaitawa ko dai zai ba da wuta ko cire wuta zuwa abubuwan kulle lokacin da aka kunna. Ana ba da alamun matsayin LED don saka idanu ikon AC, matsayin FACP, da kuma kula da fitarwar wayoyi. Hankali na hankali yana ba da kariya daga gajarta abubuwan kullewa na bazata.

Ƙayyadaddun bayanai:

Shigarwa:

• Shigarwa 220VAC, 50/60Hz, 4A.
• Biyu (2) BABU shigar da fararwa.
• Ƙimar shigar da fis: 6.3A.

Abubuwan da aka fitar:

• Zaɓuɓɓukan wuta:
  - Biyu (2) 20VDC zuwa 26.4VDC daidaitattun abubuwan sarrafawa na kulle don aikace-aikace tare da ajiyar baturi.
  24VDC don aikace-aikace ba tare da ajiyar baturi ba (Aikace-aikacen Amurka kawai).
  Ƙididdiga na yanzu 15A don 300ms, 0.75A ci gaba da wadata na yanzu.
  - 5V rike da voltage tare da 20VDC zuwa 26.4VDC na farko 100ms bugun jini.
  Matsakaicin jimlar 5V riƙe halin yanzu na duka abubuwan fitarwa shine 0.74A.
• Ɗaya (1) 20VDC zuwa 26.4VDC don aikace-aikace tare da ajiyar baturi, 24VDC don aikace-aikace a Amurka ba buƙatar ajiyar baturi ba.
  Fitowar taimako mai ƙididdigewa @ 0.75A ci gaba da wadata na yanzu (Ba abin da FACP ya shafa ba).
• Ɗaya (1) 12VDC da aka tace ingantaccen fitarwa na taimako wanda aka ƙididdige @ 0.75A a cikin ƙararrawa, 0.5A jiran aiki na yanzu (Ba ya shafa ta FACP trigger).
• Mabiya biyu (2) suna samar da fitin relay na "A" SPST wanda aka ƙididdige @ 0.6A/28VDC.
  Relays yana ƙarfafawa yayin da ake rufe shigarwa.
• Biyu (2) jinkirin abubuwan da aka saba Buɗewa ana ƙididdige su @ 0.6A/28VDC.
  Za'a iya zaɓar lokacin jinkiri 0.5 seconds ko 1 seconds. Tsawon lokacin kuzari shine daƙiƙa 1.
• Fitowar gudun ba da matsala yana nuna ƙarancin fitarwar DC voltage.

Ajiyayyen Baturi:

• An haɗa jagoran baturi.
• Ƙimar fis ɗin baturi: 25A/32V.
• Matsakaicin caji na yanzu 650mA.
• Caja da aka gina a ciki don rufaffiyar gubar acid ko nau'in batura masu nau'in gel.
• Canja atomatik zuwa baturin jiran aiki lokacin da AC ta gaza.
• Lokacin da ake amfani da batura 7AH, ƙarfin baturi don jiran aiki na gaggawa shine mintuna 30.

Alamun gani:

• Green AC Power LED yana nuna 220VAC yanzu.
• Ledojin shigar da jan wuta suna nuna halin na'urar firgita/matsala (kunna, gajere ko buɗaɗɗen kewaye).
• Koren Ƙararrawar Ƙararrawa (FAI) LED yana nuna cire haɗin FACP.
• LED baturi ja yana nuna ƙarancin baturi yayin gazawar AC da gwajin hannu.
• Green AC LED yana nuna asarar matsalar AC (ba aiki yayin jerin gwajin hannu).

Kashe Haɗin Ƙararrawar Wuta:

• Shigar da faɗakarwa na FACP Kullum Rufe.
• Zaɓuɓɓukan Kashe Haɗin Ƙararrawar Wuta mai shirye-shirye:
  - Yana kawar da wuta zuwa abubuwan fitarwa kuma yana kashe jinkirin relay mai bi.
  - Yana haɗa wuta don kulle abubuwan fitarwa kuma yana ba da damar jinkirin masu bi.

Ƙarin Halaye:

• Gwajin da hannu don ba da izinin gwada yanayin baturi.
• Daidaitacce sakin firgita daga 1 sec. zuwa dakika 30.
  Lura: Mai bi da jinkirin gudu yana kashe lokacin da zaɓin lokaci na potentiometer ya wuce bayan fitowar abin shigar da bayanai.
• An haɗa makullin kyamara.
  Girman Yaki (H x W x D kimanin): 13.5" x 13" x 3.25" (342.9mm x 330.2mm x 82.6mm)

Umarnin Shigarwa na Strikelt1V:

Hanyoyin wayoyi za su kasance daidai da National Electrical Code/NFPA 70/NFPA 72/ANSI, kuma tare da duk lambobin gida da hukumomi masu iko. An yi nufin samfurin don amfanin cikin gida kawai. Don shigarwa na Kanada - dole ne a yi amfani da wayoyi masu kariya na ma'aunin da ya dace. Ma'aikata masu izini ne za su ba da sabis da kuma rage kuzari
kafin budewa.

1. Dutsen naúrar a wurin da ake so a cikin wuraren da aka karewa (Mafi girman Nisan Waya, shafi 6). Yi alama da ramuka a bango don yin layi tare da manyan maɓallan maɓalli guda biyu a cikin shingen. Shigar da manyan haɗe-haɗe biyu da sukurori a bango tare da ɗumbin kawunan suna fitowa. Sanya manyan rijiyoyin maɓalli na sama sama biyu na sama, matakin kuma amintattu. Alama matsayi na ƙananan ramuka biyu. Cire shingen. Hana ƙananan ramuka kuma shigar da masu ɗaure biyu. Sanya ramukan maɓalli na sama sama da sukurori biyu na sama.
   Shigar da ƙananan sukurori guda biyu kuma tabbatar da ƙarfafa duk screws (Ƙaƙƙarfan Ƙirar, shafi 12). Amintaccen majalisar zuwa ƙasa.
2. Naúrar Hardwire: Haɗa ikon AC mara kunnawa (220VAC, 50/60Hz) zuwa tashoshi masu alama [L, N].
   Yi amfani da 14 AWG ko mafi girma don duk haɗin wutar lantarki. Amintaccen koren waya yana kaiwa ga lugga ƙasa.
   Ajiye wayoyi masu iyaka dabam dabam daga wayoyi marasa iyaka (220VAC, 50/60Hz Input, Wayoyin Baturi). Dole ne a ba da tazara mafi ƙarancin 0.25" (Fig. 4, shafi 10).
   HANKALI: Kar a taɓa sassan ƙarfe da aka fallasa. Kashe wutar da'irar reshe kafin shigarwa ko kayan aiki. Babu sassan da za a iya amfani da su a ciki. Koma shigarwa da sabis zuwa ƙwararrun ma'aikatan sabis.
   Haɗa ƙasan ƙasa zuwa ga lugar ƙasa. Kar a haɗa zuwa mabuɗin da mai sauyawa ke sarrafawa. An yi nufin naúrar don haɗin kai na dindindin ta amfani da tsarin rufe ƙarfe.
   Lura: StrikeIt1V ana nufin a haɗa shi ta dindindin.
3. Auna aux. fitarwa voltage kafin haɗa na'urori. Wannan yana taimakawa guje wa lalacewa mai yuwuwa.
4. Haɗa na'urar kayan aikin tsoro # 1 zuwa tashoshi masu alama [+ OUT1 -], kuma haɗa na'urar kayan aikin tsoro # 2 zuwa tashoshi masu alama [+ OUT2 -] (Hoto 1, shafi 7). Tabbatar kiyaye polarity. Don na'urorin da ke buƙatar 24VDC riƙe voltage, saita canjin DIP [SW2] zuwa KASHE, don 5VDC mai riƙe da voltage, saita canjin DIP [SW2] zuwa ON (Hoto 3b, shafi 9).
   Dole ne a saita na'urorin Hardware na tsoro zuwa Fail-Safe, matsakaicin juriyar waya ga kowane fitarwa shine 0.25 Ohm (duba ma'aunin waya da taswirar nesa, shafi 6).
   Na'urar firgici tana aiki voltage ƙayyadaddun bayanai dole ne su rufe kewayon 20VDC zuwa 26.4VDC.
   Lura: Koma zuwa jerin na'urorin kayan aikin tsoro masu jituwa, shafi. 6.
5. Saita lokacin fitarwa na kulle ta hanyar daidaita [OUT1] da [OUT2] potentiometers. Juya potentiometer kusa da agogo don ƙara lokaci ko kishiyar agogo don rage lokaci. Tsawon lokacin shine 300ms. zuwa 30 seconds (naúrar an saita masana'anta @ 300ms.) (Hoto 3a, shafi 9).
   Lura: Lokacin da ake son ikon waje na lokacin buɗe ƙofa, watau, mai karanta kati, saita lokaci zuwa mafi ƙanƙanta (gaba ɗaya counter-clockwise).
6. Haɗa Buɗewar Lambobin da aka saba (NO) Buɗewa daga na'urori masu kunnawa kamar Cibiyar Gudanarwa, REX PIR, faifan maɓalli, da sauransu zuwa tashoshi masu alama [GND, IN1] da [GND, IN2] (Hoto 1, shafi 7).
   Lura: Lokacin kunna duka shigarwar 1 da shigarwar 2 daga na'ura mai kunnawa guda ɗaya, saita canjin DIP [SW1] zuwa ON don yanayin jeri (mafi girman juriya na layin Ohm 100).
7. Haɗa ƙarin na'urorin da za a yi amfani da su (Maɓallin maɓalli, na'urorin gano motsi na REX, na'urorin lantarki, relay na waje) zuwa madaidaitan tashoshin fitar da wutar lantarki. Don na'urorin 12VDC, yi amfani da tashoshi masu alama [+ 12VDC -].
   Don na'urorin 24VDC suna amfani da tashoshi masu alama [- 24VDC +] (Fig. 1, shafi 7).
   Lura: Ƙa'idar aikitage kewayon na'urar ya kamata ya zama 20VDC zuwa 26.4VDC ko mafi girma.
8. Haɗa na'urori don sarrafawa zuwa tashoshi masu alamar [DELAYED1, DELAYED2] da/ko [FOLLOWER1, FOLLOWER2]. Dry form “A” adibas ana kimanta @ 600mA/28VDC (Hoto 1, shafi 7). Daidaita lokacin jinkiri ta amfani da maɓallin DIP [SW3] (Fig. 3b, shafi 9) (0.5 seconds tare da SW3 a cikin KASHE, daya (1) na biyu tare da [SW3] a cikin ON matsayi. An saita naúrar masana'anta don jinkirin daƙiƙa 0.5.
9. Don haɗa fasalin Cire Haɗin Ƙararrawar Wuta, waya da busasshiyar fitowar lambar sadarwa ta al'ada (NC) daga Kwamitin Kula da Ƙararrawa na Wuta zuwa tashoshi masu alama [FACP] da [GND] na StrikeIt1V.
   Maɓallin DIP na "FA Select" [SW4] yana ba da nau'i biyu (2) na aiki (Fig. 3b, shafi 9): a) Tare da maɓallin DIP [SW4] a cikin matsayi na ON, aikace-aikacen shigar da FACP mai faɗakarwa ( bude da'ira) yayin da aka kunna Input 1 da Input 2 zai sa na'urorin firgita da aka buɗe (masu ƙarfi) su sake buɗewa (de-energize). Relays masu bi za su saki (de-ergize).
   b) Tare da maɓallin DIP [SW4] a cikin KASHE, aikace-aikacen shigar da shigar da FACP (buɗewar kewayawa) yayin da Input 1 da Input 2 ba a kunna ba zai sa na'urorin kayan tsoro na kulle (de-energized) don buɗewa (ƙarfafawa). ). Relays masu bi zasu kunna (ƙarfafawa).
   Relays da aka jinkirta zai ba da kuzari na ɗan lokaci.
   Lura: Tare da SW4 a cikin KASHE, aikace-aikacen shigar da shigar da FACP (buɗaɗɗen da'irar) yayin da aka kunna Input 1 da Input 2 ba za su yi wani tasiri ba akan aikin Fitowa 1 ko Fitowa 2 da madaidaicin Mabiyan su ko Relays da aka jinkirta.
10. Lokacin amfani da batura masu aiki, dole ne su zama nau'in gubar dalma ko gel. 7AH baturi zai samar da 30 minutes na madadin lokaci. Haɗa batura biyu (2) 12VDC masu wayoyi a jeri zuwa tashoshi masu alamar [+ BAT -].
    Don aikace-aikacen Ikon Samun batir na zaɓi ne, don aikace-aikacen Kanada ana buƙatar batir.
    Lokacin da ba a yi amfani da batura ba, asarar AC zai haifar da asarar juzu'in fitarwatage.
11. Dutsen UL Jerin tamper switch (samfurin Sentrol 3012 ko makamancin haka) a saman shingen. Zamar da tampmadaidaicin madaidaicin maɓalli a gefen shingen kusan 2” daga gefen dama (Fig. 3, shafi 9).
    Haɗa tampcanza wayoyi zuwa shigar da Panel Control Panel ko na'urar da aka jera UL mai dacewa. Don kunna siginar ƙararrawa buɗe ƙofar kewayen.
    Lura: Kada ku wuce juzu'itage da kuma halin yanzu na tampya canza.
    Da fatan za a koma tamper canza shigarwa umarnin.
12. Bayan kammala wayoyi amintattun ƙofar shinge tare da sukurori ko kulle cam (an kawo).

StrikeIt1V LED Diagnostics:

LED	Halin LED	Matsayin Mai Kula da Wutar Na'urar tsoro
Green Power (AC)	On	Yanayin aiki na al'ada.
	Kashe	Asarar AC.
INP1 - Shigarwar Mai Tarawa 1	On	Fitowa na 1 - Ƙarfafawa.
	Sannun kiftawa	Fitowa ta 1 - Buɗe kewaye.
	Rapid lumshe ido	Fitowa ta 1 - Gajerun Kewayawa.
	Kashe	Fitowa ta 1 - Ƙarfafawa.
INP2 - Shigarwar Mai Tarawa 2	On	Fitowa na 2 - Ƙarfafawa.
	Sannun kiftawa	Fitowa ta 2 - Buɗe kewaye.
	Rapid lumshe ido	Fitowa ta 2 - Gajerun Kewayawa.
	Kashe	Fitowa ta 2 - Ƙarfafawa.
FAI - Green	On	An kunna shigar da FACP (yanayin ƙararrawa).
	Kashe	FACP na al'ada (yanayin rashin ƙararrawa).
BAT Matsalar Ja	Kashe	Yanayin al'ada.
	On	An fara gwajin da hannu.
	Sannun kiftawa	Baturi mai rauni ko ɓacewa, yana aiki yayin gwajin hannu, ko gazawar AC.
Matsalar AC Green	Kashe	AC normal.
	Sannu a hankali	AC low ko bace.

StrikeIt1V Ƙirar Tasha:

Labarin Ƙarshe	Aiki/Bayyana
L, G, N	Haɗa 220VAC, 50/60 Hz zuwa waɗannan tashoshi: L zuwa Hot, N zuwa tsaka tsaki.
+ 12VDC	12VDC Taimakon Fitarwa @ 0.75A a cikin ƙararrawa, 0.5A cikin jiran aiki.
+ 24VDC	24VDC Taimakon Fitar @ 0.75A. 20VDC zuwa 26.4VDC don aikace-aikace tare da ajiyar baturi.
# SUNA?	24VDC Tsaya-by Haɗin Baturi (Biyu (2) 12VDC baturi masu waya a jere).
- FITA 1 +	Haɗa 24VDC Firgitar Hardware Na'urar #1 (Duba ginshiƙi mai dacewa don sauran na'urorin da aka lissafa na UL. Yanayin aiki na na'urar dole ne ya rufe kewayon 20VDC zuwa 26.4VDC 0.25 Ohm matsakaicin juriya na wayoyi).
- FITA 2 +	Haɗa 24VDC Firgitar Hardware Na'urar #2. (Duba ginshiƙi masu dacewa don wasu na'urorin da aka lissafa na UL. Dole ne kewayon aiki na na'urar ya rufe kewayon 20VDC zuwa 26.4VDC 0.25 Ohm matsakaicin juriyar wayoyi).
FACP/GND	Busasshiyar tuntuɓar da aka rufe ta al'ada daga Ikon ƙararrawa na Wuta (matsakaicin juriyar wayoyi 100 Ohm).
IN1/GND	Yawanci Buɗe Maɗaukakin shigar da shigarwar Fitowa 1. Ana iya rufe shi don tsawaita buɗewa (mafi girman juriyar wayoyi 100 Ohm).
IN2/GND	Yawanci Buɗe Maɗaukakin shigar da shigarwar Fitowa 2. Ana iya rufe shi don tsawaita buɗewa (mafi girman juriyar wayoyi 100 Ohm).
An jinkirta 1	Busashen form “A” lambobin sadarwa suna ba da bugun bugun jini na daƙiƙa 1 bayan jinkirin saiti. Tare da maɓallin DIP [SW3] a cikin KASHE, jinkirin shine 0.5 seconds. Tare da maɓallin DIP [SW3] a cikin matsayi na ON, jinkirin shine 1 na biyu (Fig. 3b, shafi 9). Wannan yana ba da damar Na'urar Hardware ta firgita don buɗewa gabaɗaya kafin yin sigina ga ma'aikacin auto don lanƙwasa kofa.
An jinkirta 2	Busashen form “A” lambobin sadarwa suna ba da bugun bugun jini na daƙiƙa 1 bayan jinkirin saiti. Tare da maɓallin DIP [SW3] a cikin KASHE, jinkirin shine 0.5 seconds. Tare da maɓallin DIP [SW3] a cikin matsayi na ON, jinkirin shine 1 na biyu (Fig. 3b, shafi 9). Wannan yana ba da damar Na'urar Hardware ta firgita don buɗewa gabaɗaya kafin yin sigina ga afaretan auto zuwa ƙofar lilo.
Mabiya 1	Dry form “A” lamba. Yana ƙarfafawa yayin da aka samar da fitarwa na 1. Yana ba da damar kunna farantin sauya ADA a waje don kunna afaretan auto yayin da ƙofar ke buɗe. Yana kashe kunnawa a wajen mai kunnawa ADA yayin da aka kulle kofa.
Mabiya 2	Dry form “A” lamba. Yana ƙarfafawa yayin da aka samar da fitarwa na 2. Yana ba da damar kunna farantin sauya ADA a waje don kunna afaretan auto yayin da ƙofar ke buɗe. Yana kashe kunnawa a wajen mai kunnawa ADA yayin da aka kulle kofa.
Kulawa	Yana nuna ƙarancin fitarwa na DC voltage hali. Ana iya haifar da shi ta launin ruwan kasa na AC da ƙarancin baturi da ke faruwa a lokaci guda. Ana buƙatar gwajin kai na littafin don tantance yanayin baturi.

Na'urorin Hardware masu jituwa masu jituwa:

Mai ƙira	Lambar Samfura
Zabin Farko	3600 - Na'urar Fitar Sanda A tsaye 3700 - Na'urar Fitar da Rim
Kawneer	Na'urar Fita ta EL Paneline
Von Duprin®	EL98 Series Hardware na tsoro tare da Latch Latch
SHINE	7500 Yajin Wutar Lantarki

Madaidaicin Teburin Nisan Waya:
Matsakaicin juriya na 0.25 Ohm na haɗa wayoyi abin karɓa ne, duba ginshiƙi na ƙasa don ma'aunin waya da nisa.

Waya	Nisa
14 AWG Strand	40 ft.
12 AWG Strand	60 ft.
10 AWG Strand	100 ft.

Lura: Don aiki mai zaman kansa na Fitowa 1 da 2, haɗa NO bushe lamba tsakanin IN1 da GND da/ko IN2 da GND.
Domin aiki na jere na OUT1 da OUT2 shigar da jumper tsakanin IN1 da IN2 da jumper tsakanin duka tashoshi na GND.

Lura: StrikeIt1 an yi niyya don amfani tare da na'urorin kayan tsoro na VON DUPRIN®.
VON DUPRIN® alamar kasuwanci ce mai rijista ta Allegion.

Abubuwan Buƙatun Waya na Iyakantaccen Wutar NEC don Samfurin StrikeIt1V:
Wayoyin da'ira mai iyaka da mara ƙarfi dole ne su kasance cikin rabuwa a cikin majalisar. Duk wayoyi masu iyakacin wutar lantarki dole ne su kasance aƙalla 0.25” nesa da kowane wayoyi marasa iyaka. Bugu da ƙari, duk na'urorin da'ira mai iyaka da wutar lantarki da na'urorin da ba su da iyaka dole ne su shiga kuma su fita daga majalisar ta hanyoyi daban-daban.
Daya irin wannan example na wannan aka nuna a kasa. Takamammen aikace-aikacen ku na iya buƙatar yin amfani da ƙwanƙwasawa daban-daban. Ana iya amfani da kowane ƙwanƙwasa magudanar ruwa. Don aikace-aikacen iyakantaccen wutar lantarki, amfani da magudanar ruwa zaɓi ne. Dole ne a yi duk hanyoyin haɗin yanar gizo ta amfani da ma'auni mai dacewa CM ko FPL waya mai jaki (ko madaidaicin daidai).
Lura: Koma zuwa zane mai sarrafa waya a ƙasa don hanyar da ta dace don shigar da waya mai jakin CM ko FPL (Fig. 4a).

Kulawa:

Ya kamata a gwada naúrar aƙalla sau ɗaya a shekara don aikin da ya dace kamar haka:

Kulawa na FACP:
Don tabbatar da haɗin da ya dace da aiki na cire haɗin haɗin Ƙararrawar Wuta, cire waya daga tashar da aka yiwa alama [FACP] akan StrikeIt1V. Tare da sauyawar DIP [SW4] a cikin ON matsayi, buɗe na'urorin Hardware na tsoro za su buɗe. Tare da maɓallin DIP [SW4] a cikin KASHE (Fig. 3b, shafi na 9), na'urorin Hardware na Panic kulle za su sake buɗewa.
Fitarwa Voltage Gwaji: A ƙarƙashin yanayin kaya na yau da kullun, fitarwar DC voltage ya kamata a duba don daidai voltage darajar.
Gwajin Baturi:
A ƙarƙashin yanayin kaya na al'ada duba cewa an cika cajin baturin, kuma duba ƙayyadadden voltage duka a tashar baturi da kuma tashoshin allon allo masu alamar [+ BAT -] don tabbatar da cewa babu karya a cikin wayoyi masu haɗin baturi. Danna maɓallin gwaji na Manual.
LED baturi ya kamata a haskaka yayin gwajin kai (kimanin daƙiƙa 15.
Lokacin da LED ɗin baturi ya yi kyalkyali a hankali, wannan yana nuna cewa baturin ya yi ƙasa ko ya ɓace kuma yana iya buƙatar sauyawa ko aiki.
Lura: Matsakaicin caji na yanzu ƙarƙashin fitarwa shine 650mA.
Lura: Rayuwar baturi da ake tsammani shine shekaru 5; duk da haka ana bada shawarar canza batura a cikin shekaru 4 ko ƙasa da haka idan an buƙata.
Tsanaki:
Don ci gaba da kariya daga haɗarin girgiza wutar lantarki da haɗarin wuta, maye gurbin fis ɗin shigar da nau'in da ƙima: 6.3A/250V.
Kada a bijirar da ruwan sama ko danshi; amfani na cikin gida kawai.

Girman Rukuni:
13.5" x 13" x 3.25" (342.9mm x 330.2mm x 82.6mm)

Altronix baya da alhakin kowane kuskuren rubutu.
140 58th Street, Brooklyn, New York 11220 Amurka
waya: 718-567-8181
fakis: 718-567-9056
website: www.altronix.com
e-mail: info@altronix.com
Garanti na rayuwaStrikeIt1V Jagoran Shigarwa

Takardu / Albarkatu

	Altronix StrikeIt1V Mai Kula da Wutar Lantarki na Na'urar tsoro [pdf] Jagoran Shigarwa StrikeIt1V, Mai Kula da Wutar Lantarki na Na'urar tsoro, StrikeIt1V Mai Kula da Na'urar tsoro
	Altronix STRIKEIT1V Mai Kula da Wutar Lantarki na Na'urar tsoro [pdf] Jagoran Shigarwa STRIKEIT1V.

Magana

• Manual mai amfani