ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Development Board
Ẹya agbalagba: ESP32-C6-DevKitC-1 v1.1 Itọsọna olumulo yoo ran ọ lọwọ lati bẹrẹ pẹlu ESP32-C6-DevKitC-1 ati pe yoo tun pese alaye ijinle diẹ sii. ESP32-C6-DevKitC-1 jẹ igbimọ idagbasoke ipele titẹsi ti o da lori ESP32-C6-WROOM-1(U), module idi gbogbogbo pẹlu filasi 8 MB SPI. Igbimọ yii ṣepọ Wi-Fi pipe, Bluetooth LE, Zigbee, ati awọn iṣẹ Thread. Pupọ julọ awọn pinni I / O ti fọ si awọn akọle pin ni ẹgbẹ mejeeji fun ibaramu irọrun. Awọn olupilẹṣẹ le so awọn agbeegbe pọ pẹlu awọn okun onirin tabi gbe ESP32-C6-DevKitC-1 sori apoti akara.
Iwe naa ni awọn apakan pataki wọnyi
- Bibẹrẹ: Pariview ti ESP32-C6-DevKitC-1 ati hardware/software setup ilana lati to bẹrẹ.
- Itọkasi Hardware: Alaye alaye diẹ sii nipa ohun elo ESP32-C6-DevKitC-1.
- Awọn alaye Atunyẹwo Hardware: Itan atunyẹwo, awọn ọran ti a mọ, ati awọn ọna asopọ si awọn itọsọna olumulo fun awọn ẹya iṣaaju (ti o ba jẹ eyikeyi) ti ESP32-C6-DevKitC-1.
- Awọn iwe aṣẹ ti o jọmọ: Awọn ọna asopọ si awọn iwe ti o jọmọ.
Bibẹrẹ
Abala yii n pese ifihan kukuru si ESP32-C6-DevKitC-1, awọn itọnisọna lori bi o ṣe le ṣe iṣeto ohun elo akọkọ, ati bii o ṣe le filasi famuwia sori rẹ.
Apejuwe ti irinše
Awọn paati bọtini ti igbimọ ni a ṣe apejuwe ni ọna aago kan
| Ẹya bọtini | Apejuwe |
|
ESP32-C6-WROOM- 1 tabi ESP32-C6- WROOM-1U |
ESP32-C6-WROOM-1 ati ESP32-C6-WROOM-1U jẹ gbogbogbo-
Awọn modulu idi ti n ṣe atilẹyin Wi-Fi 6 ni ẹgbẹ 2.4 GHz, Bluetooth 5, ati IEEE 802.15.4 (Zigbee 3.0 ati Thread 1.3). Wọn ti wa ni itumọ ti ni ayika ESP32-C6 ërún, ati ki o ba pẹlu kan 8 MB SPI filasi. ESP32-C6- WROOM-1 nlo eriali PCB lori-ọkọ, nigbati ESP32-C6-WROOM- 1U nlo asopo eriali ita. Fun alaye diẹ ẹ sii, wo ESP32- C6-WROOM-1 Datasheet. |
|
Akọsori Pin |
Gbogbo awọn pinni GPIO ti o wa (ayafi fun ọkọ akero SPI fun filasi) ti fọ si awọn akọle pin lori ọkọ. |
| 5 V to 3.3 V LDO | Olutọsọna agbara ti o ṣe iyipada ipese 5 V sinu iṣelọpọ 3.3 V. |
| 3.3 V Agbara Lori LED | Tan-an nigbati agbara USB ti sopọ si igbimọ. |
| USB-to-UART
Afara |
Chirún afara USB-si-UART kan n pese awọn oṣuwọn gbigbe to 3 Mbps. |
|
ESP32-C6 USB Iru-C Port |
Ibudo USB Iru-C lori ifaramọ chirún ESP32-C6 pẹlu iyara ni kikun USB 2.0. O ni agbara ti iyara gbigbe 12 Mbps (Akiyesi pe ibudo yii ko ṣe atilẹyin ipo gbigbe iyara giga-iyara 480 Mbps). A lo ibudo yii fun ipese agbara si igbimọ, fun awọn ohun elo ikosan si chirún, fun ibaraẹnisọrọ pẹlu ërún nipa lilo awọn ilana USB, ati fun J.TAG n ṣatunṣe aṣiṣe. |
|
Bọtini bata |
Download bọtini. Diduro mọlẹ Bata ati lẹhinna tẹ Tunto pilẹtàbí famuwia Download mode fun gbigba famuwia nipasẹ awọn tẹlentẹle ibudo. |
| Bọtini atunto | Tẹ bọtini yii lati tun eto naa bẹrẹ. |
|
USB Iru-C to UART Port |
Ti a lo fun ipese agbara si igbimọ, fun awọn ohun elo ikosan si ërún, bakanna bi ibaraẹnisọrọ pẹlu chirún ESP32-C6 nipasẹ afara USB-to-UART lori ọkọ. |
| RGB LED | LED RGB adirẹsi adirẹsi, ìṣó nipasẹ GPIO8. |
|
J5 |
Ti a lo fun wiwọn lọwọlọwọ. Wo awọn alaye ni Abala Wiwọn lọwọlọwọ. |
Bẹrẹ Idagbasoke Ohun elo
Ṣaaju ṣiṣe agbara ESP32-C6-DevKitC-1 rẹ, jọwọ rii daju pe o wa ni ipo ti o dara laisi awọn ami ibajẹ ti o han gbangba.
Ti beere Hardware
- ESP32-C6-DevKitC-1
- USB-A si okun USB-C
- Kọmputa nṣiṣẹ Windows, Linux, tabi macOS
Akiyesi
Rii daju lati lo okun USB ti o ni agbara to dara. Diẹ ninu awọn kebulu wa fun gbigba agbara nikan ati pe ko pese awọn laini data ti o nilo tabi ṣiṣẹ fun siseto awọn igbimọ.
Eto software
Jọwọ tẹsiwaju si ESP-IDF Bibẹrẹ, eyiti yoo ṣe iranlọwọ ni kiakia lati ṣeto agbegbe idagbasoke lẹhinna filasi ohun elo kanample lori ọkọ rẹ.
Hardware Reference
Àkọsílẹ aworan atọka
Aworan atọka ti o wa ni isalẹ fihan awọn paati ti ESP32-C6-DevKitC-1 ati awọn asopọ wọn.
Awọn aṣayan Ipese Agbara
Awọn ọna iyasọtọ mẹta lo wa lati pese agbara si igbimọ:
- USB Iru-C si UART Port ati ESP32-C6 USB Iru-C Port (boya ọkan tabi mejeeji), ipese agbara aiyipada (a ṣe iṣeduro)
- 5V ati awọn akọle pinni GND
- 3V3 ati awọn akọle pinni GND
Iwọn Iwọn lọwọlọwọ
Awọn akọle J5 lori ESP32-C6-DevKitC-1 (wo J5 ni Figure ESP32-C6-DevKitC-1 - iwaju) le ṣee lo fun wiwọn ti isiyi iyaworan nipasẹ ESP32-C6-WROOM-1 (U) module:
- Yọ jumper: Awọn ipese agbara laarin awọn module ati awọn pẹẹpẹẹpẹ lori awọn ọkọ ti wa ni ge si pa. Lati wiwọn lọwọlọwọ module, so awọn ọkọ pẹlu ohun ammeter nipasẹ J5 afori.
- Waye jumper (aiyipada ile-iṣẹ): Mu iṣẹ ṣiṣe deede ti igbimọ pada.
Akiyesi
Nigba lilo 3V3 ati GND pin afori lati fi agbara awọn ọkọ, jọwọ yọ J5 jumper, ki o si so ohun ammeter ni jara si awọn ita Circuit lati wiwọn awọn module ká lọwọlọwọ.
Block akọsori
Awọn tabili meji ti o wa ni isalẹ pese Orukọ ati Iṣẹ ti awọn akọle pin ni ẹgbẹ mejeeji ti igbimọ (J1 ati J3). Awọn orukọ akọsori pin ti han ni Figure ESP32-C6-DevKitC-1 - iwaju. Nọmba naa jẹ kanna bi ninu ESP32-C6-DevKitC-1 Schematic (PDF)
J1
| Rara. | Oruko | Iru 1 | Išẹ |
| 1 | 3V3 | P | 3.3 V ipese agbara |
| 2 | RST | I | Ga: kí ni ërún; Low: disables ni ërún. |
|
3 |
4 |
I/O/T |
MTMS 3, GPIO4, LP_GPIO4, LP_UART_RXD, ADC1_CH4, FSPIHD |
|
4 |
5 |
I/O/T |
MTDI 3, GPIO5, LP_GPIO5, LP_UART_TXD, ADC1_CH5, FSPIWP |
|
5 |
6 |
I/O/T |
MTCK, GPIO6, LP_GPIO6, LP_I2C_SDA, ADC1_CH6, FSPICLK |
| 6 | 7 | I/O/T | MTDO, GPIO7, LP_GPIO7, LP_I2C_SCL, FSPID |
|
7 |
0 |
I/O/T |
GPIO0, XTAL_32K_P, LP_GPIO0, LP_UART_DTRN, ADC1_CH0 |
|
8 |
1 |
I/O/T |
GPIO1, XTAL_32K_N, LP_GPIO1, LP_UART_DSRN, ADC1_CH1 |
| 9 | 8 | I/O/T | GPIO8 2 3 |
| 10 | 10 | I/O/T | GPIO10 |
| 11 | 11 | I/O/T | GPIO11 |
| Rara. | Oruko | Iru 1 | Išẹ |
| 12 | 2 | I/O/T | GPIO2, LP_GPIO2, LP_UART_RTSN, ADC1_CH2, FSPIQ |
| 13 | 3 | I/O/T | GPIO3, LP_GPIO3, LP_UART_CTSN, ADC1_CH3 |
| 14 | 5V | P | 5 V ipese agbara |
| 15 | G | G | Ilẹ |
| 16 | NC | – | Ko si asopọ |
J3
| Rara. | Oruko | Iru | Išẹ |
| 1 | G | G | Ilẹ |
| 2 | TX | I/O/T | U0TXD, GPIO16, FPICS0 |
| 3 | RX | I/O/T | U0RXD, GPIO17, FPICS1 |
| 4 | 15 | I/O/T | GPIO15 3 |
| 5 | 23 | I/O/T | GPIO23, SDIO_DATA3 |
| 6 | 22 | I/O/T | GPIO22, SDIO_DATA2 |
| 7 | 21 | I/O/T | GPIO21, SDIO_DATA1, FSPICS5 |
| 8 | 20 | I/O/T | GPIO20, SDIO_DATA0, FSPICS4 |
| 9 | 19 | I/O/T | GPIO19, SDIO_CLK, FSPICS3 |
| 10 | 18 | I/O/T | GPIO18, SDIO_CMD, FSPICS2 |
| 11 | 9 | I/O/T | GPIO9 3 |
| 12 | G | G | Ilẹ |
| 13 | 13 | I/O/T | GPIO13, USB_D+ |
| 14 | 12 | I/O/T | GPIO12, USB_D- |
| 15 | G | G | Ilẹ |
| 16 | NC | – | Ko si asopọ |
- P: Ipese agbara; I: Agbewọle; O: Ijade; T: Ikọju giga.
- Ti a lo lati wakọ LED RGB.
- (1,2,3,4,5) MTMS, MTDI, GPIO8, GPIO9, ati GPIO15 jẹ awọn pinni okun ti chirún ESP32-C6. Awọn wọnyi ni awọn pinni ti wa ni lo lati sakoso orisirisi awọn iṣẹ ni ërún ti o da lori alakomeji voltage iye loo si awọn pinni nigba ti ërún agbara-soke tabi eto si ipilẹ. Fun apejuwe kan ati ohun elo ti awọn pinni okun, jọwọ tọka si ES P32-C6 Datasheet> Awọn pinni Strapping apakan.
Ìfilélẹ Pin
Hardware Àtúnyẹwò alaye
ESP32-C6-DevKitC-1 v1.2
- Fun awọn igbimọ ti a ṣelọpọ lori ati lẹhin Kínní 2023 (nọmba PW: PW-2023-02-0139), J5 yipada lati awọn akọle ti o taara si awọn akọle ti o tẹ.
Akiyesi
Nọmba PW ni a le rii lori aami ọja lori awọn apoti paali nla fun awọn ibere osunwon.
ESP32-C6-DevKitC-1 v1.1
Itusilẹ akọkọse
- Iwe data ESP32-C6 (PDF)
- ESP32-C6-WROOM-1 Iwe data (PDF)
- ESP32-C6-DevKitC-1 Iṣeto (PDF)
- ESP32-C6-DevKitC-1 PCB Ìfilélẹ (PDF)
- ESP32-C6-DevKitC-1 Awọn iwọn (PDF)
- ESP32-C6-DevKitC-1 Dimensions orisun file (DXF)
Awọn iwe aṣẹ / Awọn orisun
 |
ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Development Board [pdf] Awọn ilana ESP32-C6-DevKitC-1 v1.2, ESP32-C6-DevKitC-1 v1.1, ESP32-C6-DevKitC-1 v1.2 Development Board, Development Board, Board |
