ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Board Development
Ụdị ochie: ESP32-C6-DevKitC-1 v1.1 Ntuziaka onye ọrụ ga-enyere gị aka ịmalite na ESP32-C6-DevKitC-1 ma nyekwa ozi ndị ọzọ dị omimi. ESP32-C6-DevKitC-1 bụ bọọdụ mmepe ọkwa ntinye dabere na ESP32-C6-WROOM-1(U), modul ebumnuche ebumnuche yana flash 8 MB SPI. Bọdụ a na-ejikọta Wi-Fi zuru oke, Bluetooth LE, Zigbee na ọrụ eriri. A na-agbajikwa ọtụtụ ntụtụ I/O na ndị nkụnye eji isi mee n'akụkụ abụọ maka njikọta dị mfe. Ndị nrụpụta nwere ike iji eriri jumper jikọọ mpụta ma ọ bụ tinye ESP32-C6-DevKitC-1 na bọọdụ achịcha.
Akwụkwọ ahụ nwere akụkụ ndị bụ isi
- Mmalite: Ofeview nke ESP32-C6-DevKitC-1 yana ntuziaka ntọlite ngwaike/software ka ịmalite.
- Ntuziaka Akụrụngwa: Ozi zuru ezu gbasara ngwaike ESP32-C6-DevKitC-1.
- Nkọwa ngbanwe ngwaike: Akụkọ ngbanwe, okwu ndị ama ama, yana njikọ ntuziaka onye ọrụ maka ụdị gara aga (ọ bụrụ na ọ bụla) nke ESP32-C6-DevKitC-1.
- Akwụkwọ ndị metụtara: Njikọ na akwụkwọ ndị metụtara ya.
Na-amalite
Nkebi a na-enye okwu mmalite dị nkenke na ESP32-C6-DevKitC-1, ntuziaka maka otu esi eme ntọala ngwaike mbụ, yana otu esi etinye ngwa ngwa na ya.
Nkọwa nke akụrụngwa
A na-akọwa akụkụ ndị bụ isi nke bọọdụ ahụ n'akụkụ elekere
| Akụkụ igodo | Nkọwa |
|
ESP32-C6-WROOM- 1 ma ọ bụ ESP32-C6- WROOM-1U |
ESP32-C6-WROOM-1 na ESP32-C6-WROOM-1U bụ izugbe-
modul ebumnuche na-akwado Wi-Fi 6 na band 2.4 GHz, Bluetooth 5, na IEEE 802.15.4 (Zigbee 3.0 na Thread 1.3). A na-ewu ha gburugburu mgbawa ESP32-C6, ma na-abịa na 8 MB SPI flash. ESP32-C6-WROOM-1 na-eji eriri PCB nọ na bọọdụ, ebe ESP32-C6-WROOM-1U na-eji njikọ antenna mpụga. Maka ozi ndị ọzọ, hụ ESP32- C6-WROOM-1 mpempe akwụkwọ. |
|
Isi Ntụtụ |
Ntụtụ GPIO niile dị (ma ewezuga ụgbọ ala SPI maka flash) na-agbajikwa ndị nkụnye eji isi mee na bọọdụ. |
| 5 V ruo 3.3 V LDO | Onye na-achịkwa ike nke na-agbanwe ihe ọkọnọ 5 V ka ọ bụrụ mmepụta 3.3 V. |
| 3.3 V Ike na LED | Na-agbanye mgbe ejikọrọ ike USB na bọọdụ. |
| USB-na-UART
Akwa akwa |
Otu eriri USB-na-UART na-enye ọnụego mbufe ruo 3 Mbps. |
|
ESP32-C6 USB Ụdị-C Port |
Ọdụ ụgbọ mmiri Type-C USB na mgbawa ESP32-C6 kwekọrọ na USB 2.0 zuru oke. Ọ nwere ike iru ọsọ mbufe 12 Mbps (Rịba ama na ọdụ ụgbọ mmiri a anaghị akwado ọnọdụ mbufe ọsọ ọsọ 480 Mbps ngwa ngwa). A na-eji ọdụ ụgbọ mmiri a maka inye ọkụ na bọọdụ, maka ngwa na-egbuke egbuke na mgbawa, maka nkwukọrịta na mgbawa site na iji usoro USB, yana maka J.TAG debugging. |
|
Bọtịnụ buut |
Budata bọtịnụ. Na-ejide ala buut wee pịa Tọgharia na-amalite ọnọdụ nbudata Firmware maka nbudata ngwa ngwa site na ọdụ ụgbọ mmiri. |
| Tọgharịa bọtịnụ | Pịa bọtịnụ a ka ịmalitegharịa usoro. |
|
USB Type-C ruo UART Port |
A na-eji ya maka inye ọkụ na bọọdụ, maka ngwa na-egbuke egbuke na mgbawa, yana nkwurịta okwu na mgbawa ESP32-C6 site na akwa mmiri USB-na-UART. |
| RGB LED | RGB LED nwere ike ịdenye ya, nke GPIO8 na-ebugharị. |
|
J5 |
Ejiri ya maka nha ugbu a. Hụ nkọwa n'ime nha nke ugbu a. |
Bido Mmepe Ngwa
Tupu ịkwalite ESP32-C6-DevKitC-1 gị, biko gbaa mbọ hụ na ọ nọ n'ọnọdụ dị mma na-enweghị akara doro anya nke mmebi.
Ngwaike achọrọ
- ESP32-C6-DevKitC-1
- USB-A ka eriri USB-C
- Kọmputa na-agba Windows, Linux, ma ọ bụ MacOS
Rịba ama
Jide n'aka na iji eriri USB dị mma. Ụfọdụ eriri bụ maka chaja naanị na anaghị enye ahịrị data achọrọ ma ọ bụ rụọ ọrụ maka ịhazi bọọdụ.
Mbido Sọftụwia
Biko gaa n'ihu na ESP-IDF Bido, nke ga-enyere gị aka ịtọlite ebe mmepe ngwa ngwa wee gbanye ngwa exampbanye n'ụgbọ gị.
Ntuziaka akụrụngwa
Ihe Ngosi
Eserese ngọngọ dị n'okpuru na-egosi akụkụ nke ESP32-C6-DevKitC-1 yana njikọ njikọ ha.
Nhọrọ ikenye ike
Enwere ụzọ atọ ekewapụrụ onwe ha iji nye ndị bọọdụ ike:
- USB Type-C ruo UART Port na ESP32-C6 USB Type-C Port (ma otu ma ọ bụ abụọ), ndabara ike ọkọnọ (kwadoro)
- 5V na GND pin nkụnye eji isi mee
- 3V3 na GND pin nkụnye eji isi mee
Ntụle ugbu a
Enwere ike iji ndị nkụnye eji isi mee J5 dị na ESP32-C6-DevKitC-1 (lee J5 na eserese ESP32-C6-DevKitC-1 - n'ihu) maka ịlele nke ugbu a nke ESP32-C6-WROOM-1(U) modul sere:
- Wepu jumper: A na-ebipụ ọkụ ọkụ n'etiti modul na peripherals na osisi. Iji tụọ modul ugbu a, jikọọ osisi na ammeter site na nkụnye eji isi mee J5.
- Tinye jumper (ndabara ụlọ ọrụ): Weghachite arụrụ ọrụ nke bọọdụ ahụ.
Rịba ama
Mgbe ị na-eji nkụnye eji isi mee 3V3 na GND iji mee ka bọọdụ dị ike, biko wepu jumper J5, wee jikọọ ammeter n'usoro na sekit mpụga iji tụọ modul ugbu a.
Mgbochi nkụnye eji isi mee
Tebụl abụọ dị n'okpuru na-enye Aha na Ọrụ nke ndị isi ntụtụ n'akụkụ abụọ nke bọọdụ (J1 na J3). Egosiri aha isi ntụtụ na eserese ESP32-C6-DevKitC-1 – n'ihu. Ọnụọgụ ahụ bụ otu ihe dị na ESP32-C6-DevKitC-1 Schematic (PDF)
J1
| Mba. | Aha | Ụdị 1 | Ọrụ |
| 1 | 3V3 | P | 3.3 V ike ọkọnọ |
| 2 | RST | I | Elu: na-eme ka mgbawa; Ala: gbanyụọ mgbawa. |
|
3 |
4 |
I/O/T |
MTMS 3, GPIO4, LP_GPIO4, LP_UART_RXD, ADC1_CH4, FSPIHD |
|
4 |
5 |
I/O/T |
MTDI 3, GPIO5, LP_GPIO5, LP_UART_TXD, ADC1_CH5, FSPIWP |
|
5 |
6 |
I/O/T |
MTCK, GPIO6, LP_GPIO6, LP_I2C_SDA, ADC1_CH6, FPICLK |
| 6 | 7 | I/O/T | MTDO, GPIO7, LP_GPIO7, LP_I2C_SCL, FSPID |
|
7 |
0 |
I/O/T |
GPIO0, XTAL_32K_P, LP_GPIO0, LP_UART_DTRN, ADC1_CH0 |
|
8 |
1 |
I/O/T |
GPIO1, XTAL_32K_N, LP_GPIO1, LP_UART_DSRN, ADC1_CH1 |
| 9 | 8 | I/O/T | GPIO8 2 3 |
| 10 | 10 | I/O/T | GPIO10 |
| 11 | 11 | I/O/T | GPIO11 |
| Mba. | Aha | Ụdị 1 | Ọrụ |
| 12 | 2 | I/O/T | GPIO2, LP_GPIO2, LP_UART_RTSN, ADC1_CH2, FSPIQ |
| 13 | 3 | I/O/T | GPIO3, LP_GPIO3, LP_UART_CTSN, ADC1_CH3 |
| 14 | 5V | P | 5 V ike ọkọnọ |
| 15 | G | G | Ala |
| 16 | NC | – | Enweghị njikọ |
J3
| Mba. | Aha | Ụdị | Ọrụ |
| 1 | G | G | Ala |
| 2 | TX | I/O/T | U0TXD, GPIO16, FPICS0 |
| 3 | RX | I/O/T | U0RXD, GPIO17, FPICS1 |
| 4 | 15 | I/O/T | GPIO15 3 |
| 5 | 23 | I/O/T | GPIO23, SDIO_DATA3 |
| 6 | 22 | I/O/T | GPIO22, SDIO_DATA2 |
| 7 | 21 | I/O/T | GPIO21, SDIO_DATA1, FSPICS5 |
| 8 | 20 | I/O/T | GPIO20, SDIO_DATA0, FSPICS4 |
| 9 | 19 | I/O/T | GPIO19, SDIO_CLK, FSPICS3 |
| 10 | 18 | I/O/T | GPIO18, SDIO_CMD, FSPICS2 |
| 11 | 9 | I/O/T | GPIO9 3 |
| 12 | G | G | Ala |
| 13 | 13 | I/O/T | GPIO13, USB_D+ |
| 14 | 12 | I/O/T | GPIO12, USB_D- |
| 15 | G | G | Ala |
| 16 | NC | – | Enweghị njikọ |
- P: Ike ọkọnọ; M: Ntinye; O: Mpụta; T: Nnukwu mgbochi.
- A na-eji akwọ ụgbọala RGB LED.
- (1,2,3,4,5) MTMS, MTDI, GPIO8, GPIO9, na GPIO15 na-eke ntụtụ nke mgbawa ESP32-C6. A na-eji ntụtụ ndị a jikwaa ọtụtụ ọrụ mgbawa dabere na ọnụọgụ ọnụọgụ abụọtage ụkpụrụ etinyere na atụdo n'oge mgbawa ike-elu ma ọ bụ usoro nrụpụta. Maka nkọwa na ngwa nke ntụtụ eriri, biko rụtụ aka na ES P32-C6 Datasheet> Nkebi eriri eriri.
Nhazi nghazi
Nkọwa ngbanwe ngwaike
ESP32-C6-DevKitC-1 v1.2
- Maka bọọdụ arụpụtara na na mgbe Febụwarị 2023 (nọmba PW: PW-2023-02-0139), gbanwere J5 site na nkụnye eji isi mee kwụ ọtọ gaa na nkụnye eji isi mee.
Rịba ama
Enwere ike ịchọta nọmba PW na akara ngwaahịa na nnukwu igbe kaadiboodu maka iwu n'ùkwù.
ESP32-C6-DevKitC-1 v1.1
Ntọhapụ mbụse
- Mpempe akwụkwọ ESP32-C6 (PDF)
- ESP32-C6-WROOM-1 mpempe akwụkwọ (PDF)
- ESP32-C6-DevKitC-1 nhazi (PDF)
- ESP32-C6-DevKitC-1 PCB okirikiri nhọrọ ukwuu (PDF)
- Akụkụ ESP32-C6-DevKitC-1 (PDF)
- ESP32-C6-DevKitC-1 Isi mmalite akụkụ file (DXF)
Akwụkwọ / akụrụngwa
 |
ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Board Development [pdf] Ntuziaka ESP32-C6-DevKitC-1 v1.2, ESP32-C6-DevKitC-1 v1.1, ESP32-C6-DevKitC-1 v1.2 Development Board, Development Board, Board |
