ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Boto ea Nts'etsopele
Mofuta oa khale: ESP32-C6-DevKitC-1 v1.1 Tataiso ena ea mosebelisi e tla u thusa ho qala ka ESP32-C6-DevKitC-1 hape e tla fana ka tlhaiso-leseling e tebileng. ESP32-C6-DevKitC-1 ke boto ea ntlafatso ea boemo ba ho kena e ipapisitseng le ESP32-C6- WROOM-1(U), mojule oa morero o akaretsang o nang le lebone la 8 MB SPI. Boto ena e kopanya mesebetsi e felletseng ea Wi-Fi, Bluetooth LE, Zigbee, le Thread. Bongata ba lithakhisa tsa I/O li robiloe ho lihlooho tsa phini mahlakoreng ka bobeli hore li hokahane habonolo. Bahlahisi ba ka hokela li-peripherals ka lithapo tsa jumper kapa ba beha ESP32-C6-DevKitC-1 leboteng la bohobe.
Tokomane e na le likarolo tse latelang tse kholo
- Ho qala: Ho fetaview ea ESP32-C6-DevKitC-1 le litaelo tsa ho seta ha hardware/software ho qala.
- Hardware Reference: Lintlha tse felletseng mabapi le Hardware ea ESP32-C6-DevKitC-1.
- Lintlha tsa Phetoho ea Hardware: Nalane ea ntlafatso, litaba tse tsebahalang, le likhokahano tsa litataiso tsa basebelisi bakeng sa liphetolelo tse fetileng (haeba li teng) tsa ESP32-C6-DevKitC-1.
- Litokomane Tse Amanang: Lihokelo tsa litokomane tse amanang.
Rea qala
Karolo ena e fana ka kenyelletso e khuts'oane ea ESP32-C6-DevKitC-1, litaelo tsa mokhoa oa ho etsa setup ea lisebelisoa tsa pele, le mokhoa oa ho khantša firmware ho eona.
Tlhaloso ea Likarolo
Likarolo tsa bohlokoa tsa boto li hlalositsoe ka tsela ea oache
| Karolo ea Bohlokoa | Tlhaloso |
|
ESP32-C6-WROOM- 1 kapa ESP32-C6- WROOM-1U |
ESP32-C6-WROOM-1 le ESP32-C6-WROOM-1U ke tse akaretsang-
merero e tšehetsang Wi-Fi 6 ho sehlopha sa 2.4 GHz, Bluetooth 5, le IEEE 802.15.4 (Zigbee 3.0 le Thread 1.3). Li hahiloe ho pota-pota chip ea ESP32-C6, 'me li tla le 8 MB SPI flash. ESP32-C6- WROOM-1 e sebelisa antenna ea PCB e ka har'a board, athe ESP32-C6-WROOM- 1U eona e sebelisa sehokelo sa lona sa kantle. Ho fumana lintlha tse ling, bona ESP32- Lethathamo la lintlha tsa C6-WROOM-1. |
|
Pin Header |
Lithakhisa tsohle tse teng tsa GPIO (ntle le bese ea SPI bakeng sa flash) li robehile ho lihlooho tsa phini botong. |
| 5 V ho 3.3 V LDO | Selaoli sa matla se fetolang phepelo ea 5 V hore e be sephetho sa 3.3 V. |
| 3.3 V Matla a LED | E bulela ha matla a USB a hoketsoe botong. |
| USB-to-UART
Borokho |
Chip e le 'ngoe ea borokho ea USB-to-UART e fana ka litefiso tsa phetisetso ho fihla ho 3 Mbps. |
|
ESP32-C6 USB Boema-kepe ba Mofuta oa C |
Boema-kepe ba USB Type-C ho chip ea ESP32-C6 bo tsamaellana le lebelo le felletseng la USB 2.0. E khona ho fihla ho 12 Mbps lebelo la phetisetso (Hlokomela hore boema-kepe bona ha bo tšehetse mokhoa oa phetisetso o potlakileng oa 480 Mbps). Boema-kepe bona bo sebelisetsoa ho fana ka matla ho boto, bakeng sa lits'ebetso tse benyang ho chip, bakeng sa puisano le chip ho sebelisa liprothokholo tsa USB, hammoho le J.TAG debugging. |
|
Konopo ea Boot |
Konopo ea ho jarolla. Ho tshoara fatshe Bootsa ebe o tobetsa Seta bocha e qala mokhoa oa ho jarolla Firmware bakeng sa ho jarolla firmware ka port ea serial. |
| Seta Botjha Konopo | Tobetsa konopo ena ho qala sistimi bocha. |
|
USB Type-C ho ea ho UART Port |
E sebelisoa bakeng sa phepelo ea matla ho boto, bakeng sa lits'ebetso tse benyang ho chip, hammoho le puisano le chip ea ESP32-C6 ka borokho ba USB-to-UART. |
| RGB LED | RGB LED e nang le aterese, e tsamaisoang ke GPIO8. |
|
J5 |
E sebedisetswa ho metha ha jwale. Sheba lintlha ho Karolo ea Tekanyo ea Hona Joale. |
Qala Ntlafatso ea Kopo
Pele o matlafatsa ESP32-C6-DevKitC-1 ea hau, ka kopo etsa bonnete ba hore e maemong a matle ha ho na matšoao a hlakileng a tšenyo.
Hlokahala Hardware
- ESP32-C6-DevKitC-1
- thapo ya USB-A ho isa ho USB-C
- Khomphutha e sebelisang Windows, Linux, kapa macOS
Hlokomela
Netefatsa hore o sebedisa thapo ya USB ya boleng bo botle. Lithapo tse ling ke tsa ho tjhaja feela 'me ha li fane ka lithapo tse hlokahalang tsa data kapa hona ho sebetsa bakeng sa ho hlophisa liboto.
Setup ea Software
Ka kopo tsoela pele ho ESP-IDF Get Started, e tla u thusa ka potlako ho theha tikoloho ea nts'etsopele ebe u khantša kopo ea exampke kene ka tlung ea hau.
Hardware Reference
Setšoantšo se Thibeloang
Setšoantšo sa block se ka tlase se bontša likarolo tsa ESP32-C6-DevKitC-1 le likhokahano tsa tsona.
Likhetho tsa Phepelo ea Matla
Ho na le mekhoa e meraro e ikhethileng ea ho fana ka matla ho boto:
- USB Type-C ho ea UART Port le ESP32-C6 USB Type-C Port (e le 'ngoe kapa ka bobeli), motlakase oa kamehla (oa khothaletsoa)
- 5V le lihlooho tsa phini tsa GND
- 3V3 le lihlooho tsa phini tsa GND
Tekanyo ea Hona Joale
Lihlooho tsa J5 ho ESP32-C6-DevKitC-1 (sheba J5 ho Setšoantšo sa ESP32-C6-DevKitC-1 - ka pele) li ka sebelisoa ho metha ea hajoale e huloang ke mojule oa ESP32-C6-WROOM-1(U):
- Tlosa jumper: Matla a matla pakeng tsa module le li-peripherals ka boto e khaotsoe. Ho lekanya hore na mojule o sebetsa joang, hokela boto le ammeter ka lihlooho tsa J5.
- Sebelisa jumper (fektheri ea kamehla): Khutlisa ts'ebetso e tloaelehileng ea boto.
Hlokomela
Ha o sebelisa lihlooho tsa 3V3 le GND pin ho matlafatsa boto, ka kopo tlosa jumper ea J5, 'me u kopanye ammeter ka tatellano ho potoloho ea kantle ho metha hore na mojule ke ofe.
Thibelo ea Hlooho
Litafole tse peli tse ka tlase li fana ka Lebitso le Mosebetsi oa lihlooho tsa phini mahlakoreng ka bobeli a boto (J1 le J3). Mabitso a lihlooho tsa pin a bontšoa ho Figure ESP32-C6-DevKitC-1 - ka pele. Linomoro li tšoana le tsa ESP32-C6-DevKitC-1 Schematic (PDF)
J1
| Che. | Lebitso | Mofuta 1 | Mosebetsi |
| 1 | 3V3 | P | 3.3 V phepelo ea motlakase |
| 2 | RST | I | Holimo: e nolofalletsa chip; Tlase: e tima chip. |
|
3 |
4 |
I/O/T |
MMS 3, GPIO4, LP_GPIO4, LP_UART_RXD, ADC1_CH4, FSPIHD |
|
4 |
5 |
I/O/T |
MTDI 3, GPIO5, LP_GPIO5, LP_UART_TXD, ADC1_CH5, FSPIWP |
|
5 |
6 |
I/O/T |
MTCK, GPIO6, LP_GPIO6, LP_I2C_SDA, ADC1_CH6, FSPICLK |
| 6 | 7 | I/O/T | MTDO, GPIO7, LP_GPIO7, LP_I2C_SCL, FSPID |
|
7 |
0 |
I/O/T |
GPIO0, XTAL_32K_P, LP_GPIO0, LP_UART_DTRN, ADC1_CH0 |
|
8 |
1 |
I/O/T |
GPIO1, XTAL_32K_N, LP_GPIO1, LP_UART_DSRN, ADC1_CH1 |
| 9 | 8 | I/O/T | GPIO8 2 3 |
| 10 | 10 | I/O/T | GPIO10 |
| 11 | 11 | I/O/T | GPIO11 |
| Che. | Lebitso | Mofuta 1 | Mosebetsi |
| 12 | 2 | I/O/T | GPIO2, LP_GPIO2, LP_UART_RTSN, ADC1_CH2, FSPIQ |
| 13 | 3 | I/O/T | GPIO3, LP_GPIO3, LP_UART_CTSN, ADC1_CH3 |
| 14 | 5V | P | 5 V phepelo ea motlakase |
| 15 | G | G | Fatše |
| 16 | NC | – | Ha ho khokahano |
J3
| Che. | Lebitso | Mofuta | Mosebetsi |
| 1 | G | G | Fatše |
| 2 | TX | I/O/T | U0TXD, GPIO16, FSPICS0 |
| 3 | RX | I/O/T | U0RXD, GPIO17, FSPICS1 |
| 4 | 15 | I/O/T | GPIO15 3 |
| 5 | 23 | I/O/T | GPIO23, SDIO_DATA3 |
| 6 | 22 | I/O/T | GPIO22, SDIO_DATA2 |
| 7 | 21 | I/O/T | GPIO21, SDIO_DATA1, FSPICS5 |
| 8 | 20 | I/O/T | GPIO20, SDIO_DATA0, FSPICS4 |
| 9 | 19 | I/O/T | GPIO19, SDIO_CLK, FSPICS3 |
| 10 | 18 | I/O/T | GPIO18, SDIO_CMD, FSPICS2 |
| 11 | 9 | I/O/T | GPIO9 3 |
| 12 | G | G | Fatše |
| 13 | 13 | I/O/T | GPIO13, USB_D+ |
| 14 | 12 | I/O/T | GPIO12, USB_D- |
| 15 | G | G | Fatše |
| 16 | NC | – | Ha ho khokahano |
- P: Phepelo ea matla; I: Kenyeletso; O: Sephetho; T: Boipheliso bo phahameng.
- E sebelisoa ho khanna RGB LED.
- (1,2,3,4,5) MTMS, MTDI, GPIO8, GPIO9, le GPIO15 ke lithakhisa tsa chip ea ESP32-C6. Lithapa tsena li sebelisoa ho laola mesebetsi e mengata ea chip ho latela binary voltagboleng bo sebelisitsoeng ho liphini nakong ea ho matlafatsa chip kapa ho seta sistimi bocha. Bakeng sa tlhaloso le tšebeliso ea likhoele tsa likhoele, ka kopo sheba ho ES P32-C6 Datasheet> Section Strapping Pins.
Sebopeho sa Pin
Lintlha tsa ntlafatso ea Hardware
ESP32-C6-DevKitC-1 v1.2
- Bakeng sa mapolanka a entsoeng ka February 2023 le ka morao (nomoro ea PW: PW-2023-02- 0139), J5 e fetoloa ho tloha lihloohong tse otlolohileng ho ea ho lihlooho tse kobehileng.
Hlokomela
Nomoro ea PW e ka fumanoa leiboleng ea sehlahisoa mabokoseng a maholo a khateboto bakeng sa liodara tse ngata.
ESP32-C6-DevKitC-1 v1.1
Phetolelo ea pelese
- Lethathamo la lintlha tsa ESP32-C6
- Lethathamo la lintlha tsa ESP32-C6-WROOM-1
- ESP32-C6-DevKitC-1 Schematic (PDF)
- Moralo oa ESP32-C6-DevKitC-1 PCB (PDF)
- Litekanyo tsa ESP32-C6-DevKitC-1 (PDF)
- Mohloli oa litekanyo tsa ESP32-C6-DevKitC-1 file (DXF)
Litokomane / Lisebelisoa
 |
ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Boto ea Nts'etsopele [pdf] Litaelo ESP32-C6-DevKitC-1 v1.2, ESP32-C6-DevKitC-1 v1.1, ESP32-C6-DevKitC-1 v1.2 Boto ea Nts'etsopele, Boto ea Nts'etsopele, Boto |
