ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Bungwe lachitukuko
Mtundu wakale: ESP32-C6-DevKitC-1 v1.1 Bukuli likuthandizani kuti muyambe ndi ESP32-C6-DevKitC-1 ndipo liperekanso zambiri zakuya. ESP32-C6-DevKitC-1 ndi gulu lachitukuko lolowera pa ESP32-C6- WROOM-1(U), gawo la cholinga chonse chokhala ndi 8 MB SPI flash. Gululi limaphatikiza ntchito za Wi-Fi, Bluetooth LE, Zigbee, ndi Thread. Mapini ambiri a I/O amathyoledwa pamitu ya pini mbali zonse ziwiri kuti azitha kulumikizana mosavuta. Madivelopa amatha kulumikiza zotumphukira ndi mawaya odumphira kapena kukwera ESP32-C6-DevKitC-1 pa bolodi.
Chikalatacho chili ndi zigawo zazikulu zotsatirazi
- Kuyamba: Kuthaview ya ESP32-C6-DevKitC-1 ndi malangizo a hardware/software kuti muyambe.
- Kalozera wa Hardware: Zambiri zatsatanetsatane za hardware ya ESP32-C6-DevKitC-1.
- Tsatanetsatane wa Hardware Revision: Mbiri yokonzanso, zovuta zodziwika, ndi maulalo amalozera ogwiritsa ntchito m'matembenuzidwe am'mbuyomu (ngati alipo) a ESP32-C6-DevKitC-1.
- Zolemba Zogwirizana: Maulalo ku zolembedwa zofananira.
Kuyambapo
Gawoli likupereka chidule chachidule cha ESP32-C6-DevKitC-1, malangizo amomwe mungakhazikitsire zida zoyambira, komanso momwe mungawalitsire firmware.
Kufotokozera kwa Zigawo
Zigawo zazikulu za bolodi zimafotokozedwa molunjika
| Chigawo Chofunikira | Kufotokozera |
|
ESP32-C6-WROOM- 1 kapena ESP32-C6- WROOM-1U |
ESP32-C6-WROOM-1 ndi ESP32-C6-WROOM-1U ndi onse-
Ma module a cholinga omwe amathandizira Wi-Fi 6 mu 2.4 GHz band, Bluetooth 5, ndi IEEE 802.15.4 (Zigbee 3.0 ndi Thread 1.3). Amamangidwa mozungulira chip ESP32-C6, ndipo amabwera ndi 8 MB SPI flash. ESP32-C6- WROOM-1 imagwiritsa ntchito mlongoti wa PCB, pomwe ESP32-C6-WROOM- 1U imagwiritsa ntchito cholumikizira chakunja cha mlongoti. Kuti mudziwe zambiri, onani ESP32- C6-WROOM-1 data. |
|
Pinani Mutu |
Zikhomo zonse za GPIO (kupatula basi ya SPI ya kung'anima) zathyoledwa pamitu ya pini pa bolodi. |
| 5 V mpaka 3.3 V LDO | Mphamvu yowongolera yomwe imasintha 5 V kutulutsa kukhala 3.3 V kutulutsa. |
| 3.3 V Mphamvu pa LED | Imayatsa mphamvu ya USB ikalumikizidwa ndi bolodi. |
| USB-ku-UART
Bridge |
Single USB-to-UART Bridge chip imapereka ndalama zosinthira mpaka 3 Mbps. |
|
Chithunzi cha ESP32-C6 USB Mtundu-C Port |
Doko la USB Type-C pa chip ESP32-C6 limagwirizana ndi liwiro la USB 2.0. Imatha kutengera liwiro la 12 Mbps (Dziwani kuti dokoli siligwirizana ndi njira yosinthira yothamanga kwambiri ya 480 Mbps). Dokoli limagwiritsidwa ntchito popangira magetsi ku bolodi, pakuwunikira kwa chip, kulumikizana ndi chip pogwiritsa ntchito ma protocol a USB, komanso J.TAG kukonza. |
|
Boot batani |
Tsitsani batani. Kugwira pansi Yambani ndiyeno kukanikiza Bwezerani imayambitsa Kutsitsa kwa Firmware kutsitsa firmware kudzera padoko la serial. |
| Bwezerani Batani | Dinani batani ili kuti muyambitsenso dongosolo. |
|
USB Type-C kupita ku UART Port |
Amagwiritsidwa ntchito popereka mphamvu ku bolodi, pakuwunikira kwa chip, komanso kulumikizana ndi chip ESP32-C6 kudzera pa mlatho wa USB-to-UART. |
| Chithunzi cha RGB LED | Mawonekedwe a RGB LED, yoyendetsedwa ndi GPIO8. |
|
J5 |
Amagwiritsidwa ntchito poyeza pano. Onani zambiri mu Gawo la Current Measurement. |
Yambitsani Kukulitsa Ntchito
Musanawonjezere ESP32-C6-DevKitC-1 yanu, chonde onetsetsani kuti ili bwino popanda zizindikiro zoonekeratu za kuwonongeka.
Zofunika Zida
- ESP32-C6-DevKitC-1
- Chingwe cha USB-A kupita ku USB-C
- Makompyuta omwe ali ndi Windows, Linux, kapena macOS
Zindikirani
Onetsetsani kuti mukugwiritsa ntchito chingwe cha USB chamtundu wabwino. Zingwe zina ndi zolipiritsa zokha ndipo sizipereka mizere yofunikira kapena ntchito yokonza ma board.
Kukhazikitsa Mapulogalamu
Chonde pitilizani ku ESP-IDF Yambitsani, yomwe ingakuthandizeni kukhazikitsa malo otukuka ndikuwunikira pulogalamu yakaleampndikupita ku board yanu.
Hardware Reference
Chithunzithunzi Choyimira
Chithunzi cha block pansipa chikuwonetsa zigawo za ESP32-C6-DevKitC-1 ndi kulumikizana kwawo.
Zosankha Zopangira Mphamvu
Pali njira zitatu zosiyana zoperekera mphamvu ku board:
- USB Type-C kupita ku UART Port ndi ESP32-C6 USB Type-C Port (kaya imodzi kapena zonse ziwiri), magetsi okhazikika (ovomerezeka)
- 5V ndi GND pini mitu
- 3V3 ndi mitu ya pini ya GND
Muyezo Wamakono
Mitu ya J5 pa ESP32-C6-DevKitC-1 (onani J5 pachithunzi ESP32-C6-DevKitC-1 - kutsogolo) ingagwiritsidwe ntchito kuyeza zomwe zajambulidwa ndi gawo la ESP32-C6-WROOM-1(U):
- Chotsani jumper: Mphamvu zamagetsi pakati pa module ndi zotumphukira pa bolodi zadulidwa. Kuti muyese momwe gawoli lilili, gwirizanitsani bolodi ndi ammeter kudzera pamutu wa J5.
- Ikani jumper (factory default): Bwezeretsani magwiridwe antchito a board.
Zindikirani
Mukamagwiritsa ntchito mitu ya pini ya 3V3 ndi GND kuti mugwiritse ntchito bolodi, chonde chotsani jumper ya J5, ndikulumikiza ammeter mumndandanda kudera lakunja kuti muyese momwe gawoli lilili.
Header Block
Matebulo awiri omwe ali pansipa amapereka Dzina ndi Ntchito ya mitu ya pini kumbali zonse za bolodi (J1 ndi J3). Mayina amutu wa pini akuwonetsedwa mu Chithunzi ESP32-C6-DevKitC-1 - kutsogolo. Manambala ndi ofanana ndi ESP32-C6-DevKitC-1 Schematic (PDF)
J1
| Ayi. | Dzina | Mtundu 1 | Ntchito |
| 1 | Mtengo wa 3V3 | P | 3.3 V magetsi |
| 2 | Mtengo wa RST | I | Mkulu: imathandiza chip; Pansi: imalepheretsa chip. |
|
3 |
4 |
I/O/T |
Mtengo MMS 3, GPIO4, LP_GPIO4, LP_UART_RXD, ADC1_CH4, FSPIHD |
|
4 |
5 |
I/O/T |
MTDI 3, GPIO5, LP_GPIO5, LP_UART_TXD, ADC1_CH5, FSPIWP |
|
5 |
6 |
I/O/T |
MTCK, GPIO6, LP_GPIO6, LP_I2C_SDA, ADC1_CH6, FSPICLK |
| 6 | 7 | I/O/T | MTDO, GPIO7, LP_GPIO7, LP_I2C_SCL, FSPID |
|
7 |
0 |
I/O/T |
GPIO0, XTAL_32K_P, LP_GPIO0, LP_UART_DTRN, ADC1_CH0 |
|
8 |
1 |
I/O/T |
GPIO1, XTAL_32K_N, LP_GPIO1, LP_UART_DSRN, ADC1_CH1 |
| 9 | 8 | I/O/T | Chithunzi cha GPIO8 2 3 |
| 10 | 10 | I/O/T | Chithunzi cha GPIO10 |
| 11 | 11 | I/O/T | Chithunzi cha GPIO11 |
| Ayi. | Dzina | Mtundu 1 | Ntchito |
| 12 | 2 | I/O/T | GPIO2, LP_GPIO2, LP_UART_RTSN, ADC1_CH2, FSPIQ |
| 13 | 3 | I/O/T | GPIO3, LP_GPIO3, LP_UART_CTSN, ADC1_CH3 |
| 14 | 5V | P | 5 V magetsi |
| 15 | G | G | Pansi |
| 16 | NC | – | Palibe kulumikizana |
J3
| Ayi. | Dzina | Mtundu | Ntchito |
| 1 | G | G | Pansi |
| 2 | TX | I/O/T | U0TXD, GPIO16, FSPICS0 |
| 3 | RX | I/O/T | U0RXD, GPIO17, FSPICS1 |
| 4 | 15 | I/O/T | Chithunzi cha GPIO15 3 |
| 5 | 23 | I/O/T | GPIO23, SDIO_DATA3 |
| 6 | 22 | I/O/T | GPIO22, SDIO_DATA2 |
| 7 | 21 | I/O/T | GPIO21, SDIO_DATA1, FSPICS5 |
| 8 | 20 | I/O/T | GPIO20, SDIO_DATA0, FSPICS4 |
| 9 | 19 | I/O/T | GPIO19, SDIO_CLK, FSPICS3 |
| 10 | 18 | I/O/T | GPIO18, SDIO_CMD, FSPICS2 |
| 11 | 9 | I/O/T | Chithunzi cha GPIO9 3 |
| 12 | G | G | Pansi |
| 13 | 13 | I/O/T | GPIO13, USB_D+ |
| 14 | 12 | I/O/T | GPIO12, USB_D- |
| 15 | G | G | Pansi |
| 16 | NC | – | Palibe kulumikizana |
- P: Kupereka mphamvu; Ine: Zolowetsa; O: Kutulutsa; T: High impedance.
- Amagwiritsidwa ntchito kuyendetsa RGB LED.
- (1,2,3,4,5) MTMS, MTDI, GPIO8, GPIO9, ndi GPIO15 ndi zikhomo za ESP32-C6 chip. Zikhomozi zimagwiritsidwa ntchito kuwongolera magwiridwe antchito angapo kutengera ndi binary voltage mfundo zomwe zimagwiritsidwa ntchito pazikhomo panthawi ya chip power-up kapena system reset. Kuti mufotokoze ndikugwiritsa ntchito zikhomo, chonde onani ES P32-C6 Datasheet> Zikhomo Zomangira Gawo.
Mapangidwe a Pin
Tsatanetsatane wa Hardware Revision
ESP32-C6-DevKitC-1 v1.2
- Kwa matabwa opangidwa pa February 2023 ndi pambuyo pake (nambala ya PW: PW-2023-02- 0139), J5 imasinthidwa kuchoka pamitu yowongoka kupita kumutu wopindika.
Zindikirani
Nambala ya PW ingapezeke pa cholembera pamakatoni akulu akulu amaoda ogulitsa.
ESP32-C6-DevKitC-1 v1.1
Chidziwitso choyambase
- Tsamba la deta la ESP32-C6
- Tsamba la deta la ESP32-C6-WROOM-1
- Chithunzi cha ESP32-C6-DevKitC-1 (PDF)
- Kapangidwe ka ESP32-C6-DevKitC-1 PCB (PDF)
- Makulidwe a ESP32-C6-DevKitC-1 (PDF)
- Zithunzi za ESP32-C6-DevKitC-1 file (DXF)
Zolemba / Zothandizira
 |
ESPRESSIF ESP32-C6-DevKitC-1 v1.2 Bungwe lachitukuko [pdf] Malangizo ESP32-C6-DevKitC-1 v1.2, ESP32-C6-DevKitC-1 v1.1, ESP32-C6-DevKitC-1 v1.2 Board Development, Development Board, Board |
