I-SloanLED RC-100 ye-Sensor Remote Programmer

IMIYALELO YOMSEBENZI

INGCACISO

Ukunikezwa Amandla	I-2 x AAA 1 5V ibhetri, i-Alkaline ekhethwayo
Ityala eliphetheyo	I-RC-100 kwimeko yokuthwala
Uluhlu lokulayisha	Ukuya kuthi ga kwi-15 m (50 ft.)
Op. ubushushu	0°C- 50°C (32°F- 122°F)
Imilinganiselo	123x70x20.3 mm (4. 84″ x2.76″ x0. 8″)

ISILUMKISO: Susa iibhetri kwikompatimenti ukuba iremowuthi ayiyi kusetyenziswa kwiintsuku ezingama-30.

PHEZULUVIEW

Ulawulo olukude olungenazingcingo Isixhobo soLungiso lwe-IR sisixhobo esiphathwa ngesandla soqwalaselo olukude lwe-IA-enabled fixture fixture integrated sensors. Isixhobo senza isixhobo ukuba siguqule nge-pushbutton ngaphandle kweeleli okanye izixhobo, kwaye sigcina ukuya kuthi ga kwiindlela ezine zeparamitha yenzwa ukukhawulezisa uqwalaselo lweenzwa ezininzi.
Ulawulo olukude luthumela isethingi yoluvo kwindawo yokunyuka ukuya kuthi ga kwienyawo ezingama-50. Isixhobo sinokubonisa iiparameters zenzwa esekwe ngaphambili, ikopi yeeparamitha kwaye uthumele iiparamitha ezintsha okanye ugcine iparameter profiles. Kwiiprojekthi apho ulungelelwaniso olufanayo lunokufunwa kwiindawo ezininzi okanye izithuba, esi sikhundla sibonelela ngendlela elungelelanisiweyo yoqwalaselo. Iisetingi zinokukotshwa kwindawo yonke, okanye kwiindawo ezahlukeneyo.

IZALATHISI ze-LED

I-LED	INKCAZO	I-LED	INKCAZO
UKUKHANYA	Isiphelo esiphezulu sokujika isitrim umsebenzi (Ukuseta umgangatho wemveliso yokukhanya okuqhagamshelweyo ngexesha lokuhlala)		Ukukhetha ixabiso le-lux elijikelezileyo langoku njengokukhanya kwemini. Eli nqaku lenza ukuba ulungiso lusebenze kakuhle nakweyiphi na imeko yesicelo sokwenyani.
UBUVUMANO	Ukuseta uvakalelo lokuhlala kwiSensom		Isivamvo sokukhanya sasemini siyayeka ukusebenza, kwaye zonke iintshukumo ezichongiweyo zinokuvula isibane sokukhanya, nokuba ukukhanya kwendalo kuqaqambe kangakanani.
IXESHA ELIBAMBIWEYO	Ixesha apho uluvo luyakucima khona (ukuba ukhetha inqanaba lokuma li 0) okanye nciphisa ukukhanya ukuya kwinqanaba eliphantsi emva kokuba indawo iphumile	YIMA NGEDIM	Ukuseta inqanaba lemveliso yokukhanyisa okudibeneyo ngexesha lesithuba. Inzwa iya kulawula umbane wokukhanyisa kwinqanaba elimiselweyo. Ukucwangcisa inqanaba le-STAND-BY DIM ku-0 kuthetha ukuba ukukhanya kuvaliwe ngexesha lesithuba.
ISIZIVA ZEMINI	Ukumela imiqobo eyahlukeneyo yenqanaba lokukhanya kwendalo kwiSensom .	YIMA NGEXESHA	Ukumela ixesha apho uluvo luzakugcina ukukhanya kumphakamo osezantsi mfiliba emva kokuba KUBAMBA IXESHA liphelile.

UKUSETYENZISWA KWEBHUNTI

IQHOSHA	INKCAZO	IQHOSHA	INKCAZO
	Cinezela iqhosha, ukukhanya kuya kwimodi esisigxina okanye esisigxina, kwaye inzwa ivaliwe. (KUMELE ucinezele iqhosha lika-@ ukuyeka le mowudi yokuSeta.		Cinezela iqhosha le-8, inzwa iqala ukusebenza kwaye zonke izicwangciso zihlala zifana nesimo samva nje ngaphambi kokuba ukukhanya kucinywe / kucinywe.
	Bonisa iiparamitha zokuseta yangoku/yokugqibela kwizikhombisi ze-LED (izalathi ze-LED ziya kuvula ukubonisa iiparitha zokuseta).		Iqhosha lelokuvavanya uvakalelo lwenjongo kuphela. Emva kokukhetha imingcele yobuntununtunu, emva koko ucinezela iqhosha, Uluvo luya kwimowudi yovavanyo(ixesha lokubamba zii-2s kuphela) ngokuzenzekelayo, ngeli xesha ixesha lokuma kunye nokukhanya kwemini zivaliwe. Cofa iqhosha lika-@ ukuyeka kule modi.
	Cofa @ iqhosha, zonke iisetingi zibuyela umva kuseto lwediphu Tshintsha kwinzwa.
	Ngena kwimeko yokumisela, iiparameter ezikhokelayo zolawulo olukude ziya kudanyaza ukuze zikhethwe. kwaye Hamba uye UP naPhantsi ukuze ukhethe iiparamitha ezikhethiweyo kwiimpawu ze-LED.		Yiya kwi-LEFT kunye ne-RIGHT ukukhetha iiparamitha ezikhethiweyo kwiimpawu ze-LED.
	Qinisekisa iiparamitha ezikhethiweyo ezikhethiweyo iiparamitha kulawulo olukude.		Vula kwaye uvale iSensom yokukhanya emini. Cinezela @ okanye (!) Ngenisa kwimeko yokumisela, iparameter ekhokelayo yolawulo olukude iya kukhanyisa ukuze ikhethwe, Cinezela @ ukuze uvule okanye uvale iSensor yokukhanya kwemini.
	Cinezela iqhosha le-@, layisha iiparamitha zangoku kwi-sensor(s), ukukhanya okukhokelwayo apho umenzi woluvo iziqhagamshelo ziya kuvulwa/zicinywe njengesiqinisekiso.
	4 Iimowudi zescene ezineeparamitha esetwe kwangaphambili ezifumanekayo ukuba zitshintshwe kwaye zigcinwe kwiimowudi.

UKUSETHA

I-SETTING Content iqulethe zonke iisetingi ezikhoyo kunye neeparameters ze-remote sensors. Ikuvumela ukuba utshintshe ulawulo olukhoyo, iiparamitha, kunye nokusebenza kwenzwa ukusuka kwi-factory default okanye iparameters zangoku. Tshintsha useto oluninzi lwe sensor(s)

1. Cofa§iqhosha, iiledi zolawulo olude ziya kubonisa iiparamitha zakutsha ozisethileyo.
2. Cinezela@or® ngenisa kwimeko yokuseta, iiparamitha ezikhokelayo zolawulo olukude ziya kudanyaza ukuze zikhethwe, jonga kuseto olufunekayo ngokucinezela@®@® ukukhetha iiparamitha ezintsha.
3. Cofa u-ok ukuqinisekisa lonke useto kunye nokugcina.
4. Injongo kwi-sensor ekujoliswe kuyo kwaye ucinezele ukulayisha iparamitha entsha, ukukhanya okukhokelwayo apho inzwa idibanisa iya kuvula / icime njengoko kuqinisekiswa.

• QAPHELA: useto lusebenza inyathelo eliphambili nguPush @or ®, ngenisa kwimeko yokuseta.
• QAPHELA: Ukukhanya okukhokelwayo apho inzwa yoluvo iqhagamsheleka kuyo kuya kudanyaza/cima ukuqinisekisa ukufumana iiparamitha ezintsha
• QAPHELA: Ukuba ucinezela iqhosha le-§, izikhombisi ezikhokelela kude ziya kubonisa iiparamitha zakutsha ezithunyelweyo.

Guqula iisetingi ezininzi zabenzi boluvo nge-smart photocell sensor Vula

1. Cinezela u-S, izikhombisi ezikhokelayo ezikude ziya kubonisa iiparitha zamva nje.
2. Cinezela okanye ngenisa kwimeko yokumisela, iparameter Izalathisi ezikhokelwayo zolawulo olukude ziya kukhanya ukuze zikhethwe.
3. Cinezela izikhombisi ezi-2 ezikhokelayo ziya kudanyaza kuseto lwesensom yokukhanya kwemini, khetha ukukhanya kwemini njengendawo yokumisela ukukhanya ngokuzenzekelayo, khetha ukukhanya kwemini njengendawo yokukhanya ukucima ngokuzenzekelayo.
4. Cofa ukuqinisekisa lonke useto kunye nokugcina.
5. Ijolise kwi-sensor ekujoliswe kuyo kwaye ucinezele ukulayisha iparameter entsha. Isibane esikhokeleyo esidityaniswe ngumenzi woluvo siya kuvulwa/cinywe.

PHAWULA:  ivaliwe ngokungagqibekanga.

1. Vula okanye uvale isivamvo sokukhanya sasemini ngokutyhala xa ulawulo olukude lukwimeko yokumisela.
2.  Xa isivamvo sokukhanya kwemini sivuleka, izikhombisi ezi-2 zeLed ziyadanyaza kwisetingi yesivamvo semini. khetha ukukhanya kwemini G njengendawo yokumisela ukukhanyisa Ngokuzenzekela , khetha ukukhanya kwemini njengendawo yokumisela ukukhanyisa ngokuzenzekelayo.Xa isivamvo sokukhanya sasemini sivalekile, isalathisi esi-1 seLed yidanya kwisetingi yesivamvo sokukhanya kwemini ukukhetha umda woluvo lwemini.
3. Xa i-sensor yokukhanya kwemini ivulekile, ixesha lokuma li-8 kuphela
4.  Inzwa yokukhanya kwemini ye-Smart ithatha indawo ye-photocell sensor eqhelekileyo kwaye isebenza ngokuzimeleyo.
5.  Jonga uMsebenzi weSensor yeMini.

Umsebenzi weCorridor

Lo msebenzi ngaphakathi kwinzwa yentshukumo ukufezekisa ulawulo lwenqanaba lesithathu. kwezinye iindawo ezifuna isaziso sokutshintsha ukukhanya phambi kokuba kucinywe. I-sensor inikezela ngamanqanaba e-3 yokukhanya: 100% -> ukukhanya okukhanyayo (ukukhanya kwendalo akwanele) -> cima; kunye namaxesha ama-2 exesha elikhethiweyo lokulinda: ixesha lokubamba isindululo kunye nexesha lokulinda; Umda wokukhanya wemini okhethiweyo kunye nendawo yokufumana inkululeko.

Umsebenzi woVavanyo lweMini

Vula inzwa yokukhanya kwemini nge push@ xa ulawulo olukude lukwimeko yokumisela.

Umsebenzi weCorridor VS uMsebenzi woVavanyo lweMini.

1. ln umsebenzi wepaseji, vula isibane KUFUNEKA ngomgangatho wokukhanya kwendalo osezantsi kweseti yokukhanya kwemini kunye nokuHlala. Kumsebenzi wesivamvo sokukhanya sasemini, vula isibane ngomgangatho wokukhanya wendalo osezantsi wokukhanya kwemini ukuze ukhanyise nokuba kukho isithuba.
2. ln umsebenzi wepaseji, cima isibane ngokugqiba kwexesha lokuma ukuba kukho isithuba. Kumsebenzi wesivamvo sokukhanya sasemini, cima isibane ngenqanaba lokukhanya kwendalo ngaphezulu kunendawo yokuseta emini ukucima nokuba kulapho.
3. ln ukusebenza kwenzwa yokukhanya kwemini, inqanaba lokukhanya kwendalo likhaphukhaphu / lisezantsi kunokukhanya kwemini ukuseta ukucima / ukulayita KUFANELE ugcine ubuncinci umzuzu omnye, oya kucima / ukukhanyisa ngokuzenzekelayo.

Malunga nokuseta FUTHI NEMODE(1,2,3,4)
Ulawulo olukude luza ne-4 Scene MODES ezingagqibekanga. Unokwenza iiparamitha ezifunekayo kwaye ugcine njengeMODE entsha (1,2,3,4) ukuqwalasela abenzi boluvo abafakelweyo.
UKUHLAZA: zonke izicwangciso zibuyela umva kuseto lwe-DIP Tshintshela kwisivamvo.
IIINDLELA ZESIQINISEKISO (1 2 3 4)

Isicelo	Ukhetho Lwendawo	Ukuqaqamba	Indawo yokuchonga	Bamba Ixesha	Ixesha lokuma	Yima ngeNqanaba eliDim	Isivamvo seMini
Ngaphakathi	Imowudi yoku-1	100.	75%	5min	30min	30%	@
Ngaphakathi	Indlela2	100%	75%	1min	+yho	30%	@
Ngaphakathi	Indlela3	100.	75%	5min	30min	30%	30LUX
Ngaphandle	Indlela4	100%	75%	1min	+yho	30%	@(30LUX/300LUX)

Guqula iiMODE:

1.  cofa@ !@!@!@ iqhosha, ulawulo olude lwezalathi zeLed zibonisa iiparamitha ezikhoyo.
2. cofa @(!)@(B ukukhetha iparameters ezintsha.
3. Cofa (§)ukuqinisekisa zonke iiparamitha kunye nokugcina kwimowudi.

LAPHA

Umsebenzi wokulayisha ikuvumela ukuba uqwalasele inzwa kunye nazo zonke iiparameters kumsebenzi omnye. Unokukhetha OKUSEKO iiparamitha okanye iMODE yokulayisha. Iiparameters zangoku okanye iMODE iboniswe kulawulo olukude . Layisha iparameters zangoku kwi sensor(s), kwaye phinda iparameters zoluvo ukwenza enye kwenye

1. Cofa iqhosha okanye ucinezele zonke iiparameters ziboniswa kulawulo olukude.
   • Phawula: khangela ukuba zonke iiparamitha zichanekile, ukuba akunjalo, zitshintshe.
2.  Injongo kwi-sensor kwaye cinezela iqhosha § , ukukhanya okudibanisa inzwa kuya kuvula / kucinywe njengoko kuqinisekiswa.
   • Phawula: ukuba enye inzwakazi idinga iiparamitha ezifanayo, jonga nje kwi-sensor kwaye ucinezele iqhosha.

Amaxwebhu / Izibonelelo

I-SloanLED RC-100 ye-Sensor Remote Programmer [pdf] Incwadi Yomyalelo I-RC-100, i-Sensor Remote Programmer

Iimbekiselo

• Incwadi yokusebenzisa