I-WM-RELAYBOX WM-RelayBox Innovation kwiiSmart IoT Systems

IINDLELA ZESIXHOBO

1. Isigqubuthelo setheminali
2. Ikhava ephezulu (indawo ephezulu, ekhusela iPCB)
3. Isikrufu sokuqinisa isiciko esingaphezulu (sitywinwe)
4. Isiseko inxalenye
5. Iindawo zokuxhoma ezisezantsi
6. Igalelo lamandla (izikhonkwane ezi-2 zokuqala kwibhloko yeterminal yeengcingo zeAC, pinout (ukusuka ekhohlo ukuya ekunene): L (umgca), N (uphakathi)
7. Unxibelelwano lwe-Relay (ii-4pcs terminal block pairs (4x 2-wire), i-Single-Pole SPST, COM/NC)
8. Igalelo lojongano lwe-E-Meter (RS485, RJ12, 6P6C)
9. Ukulungiswa kweengcingo zegalelo / imveliso - kwibhloko ye-terminal (ngezikrufu)
10. Imveliso yojongano lwe-HAN / P1 (Izibuko loNxibelelwano loMthengi, RJ12, 6P6C, 2kV eyedwa)
11. Nut for Terminal cover Fastener Screw
12. Ukudlula (ukunqunyulwa) - kwintambo yonxibelelwano ye-E-Meter
13. Indawo yokuxhoma ephezulu
14. Iimeko ze-LED
15. Isigqubuthelo sothuli se-HAN / P1 interface

IIDATHA ZOBUGCISA

Amandla voltage: ~207-253V AC, 50Hz (230V AC +/-10%, 50Hz)
Ukusetyenziswa: 3W
Ukugqithisatagukhuseleko: ngokwe-EN 62052-21
Ukubuyisela: I-4pcs ezimeleyo ye-single-pole SPST relays kunye ne-COM / NO switching, ukutshintshela ubuninzi. 250V AC voltage @ 50Hz, ukuya kuthi ga kwi-5A yokuxhathisa umthwalo we-RJ12 kumazibuko:

• Igalelo le-RJ12 (9): kuqhagamshelo lwemitha ehlakaniphile
• Imveliso ye-HAN / P1 (11): yokuqhagamshela kuMxube woMthengi

Ubushushu bokusebenza / obugciniweyo: phakathi -40'C kunye +70 'C, kwi-0-95% rel. ukufuma
Imilinganiselo: 118 x 185 x 63 mm / Ubunzima: 370 gr.
Ibhokisi: IP21-ekhuselweyo yeplastiki ebiyelweyo enesigqubuthelo setheminali
Ukukhawuleza / ukulungiswa: Nyuka eludongeni okanye iDIN-kaloliwe

QAPHELA! MUSA UKUQHAGAMSHELANA ~ 230V AC KUFAKA LWEMANDLA (7) KWISIXHOBO UDE UQHINEKELELE IIKHELI (8)!
MUSA UKUYIVULA IKHASI YESIXHOBO OKANYE UYIBAMBE IPHANSI YESEKUKA NAZO NAZIPHI NA IMEKO! MUSA UKUTYHALA IZINTO ZEMTALI KWISIXHOBO! SUKUZIPHATHA IZINTO ZESITHILI NGEXESHA ISIXHOBO ESIXHISIWE OKANYE SINXINWE!

AMANYATHELO OKUFAKA

1. Qinisekisa ukuba isixhobo asikho phantsi kwamandla/unikezelo lwevolthitage!
2. Susa i-terminal cover (No. 1) ngokukhupha i-Fastener Screw (Nr.3).
   Sebenzisa i-screwdriver ye-VDE ehambelanayo ye-PZ/S2 chwetheza isikrufu sentloko.
3. Slayida phezulu icandelo leSigubungelo seTheminali (Nombolo 1) ngocoselelo ukusuka kwindawo yeSiseko (Nombolo 5), uze ususe isigqubuthelo.
4. Ngoku ungakhulula ukudibanisa iingcingo kwibhloko yeterminal. Khulula izikrufu ze-fastener (10) zamagalelo ebhloko ye-terminal kwaye wenze iingcingo.
   Qaphela, ukuba iintloko ze-screw ziyi-PZ/S1 uhlobo, ngoko sebenzisa i-screwdriver ye-VDE ehambelanayo. Emva kokwenza i-wiring, qinisa izikrufu.
5. Xhuma intambo ye-RJ12 ye-smart meter (B1) kwi-E-Meter connector (9).
6. Qhuba iingcingo ngokomzobo wocingo okwisincamathelisi esiphakathi.
7. Ukuba uyafuna, qhagamshela iRelay #1 iperi yocingo (NO / COM) kwizikhonkwane nr. 3, 4. Icala elichasayo lekhebula kufuneka lixhunywe kwisixhobo sangaphandle, ofuna ukusilawula / ukutshintshela kwi-relay.
8. Ukuba uyafuna, qhagamshela iRelay #2 iperi yocingo (NO / COM) kwizikhonkwane nr. 5, 6. Icala elichasayo lekhebula kufuneka lixhunywe kwisixhobo sangaphandle, ofuna ukusilawula / ukutshintshela kwi-relay.
9. Ukuba uyafuna, qhagamshela iRelay #3 iperi yocingo (NO / COM) kwizikhonkwane nr. 7, 8. Icala elichasayo lekhebula kufuneka lixhunywe kwisixhobo sangaphandle, ofuna ukusilawula / ukutshintshela kwi-relay.
10. Ukuba uyafuna, qhagamshela iRelay #4 iperi yocingo (NO / COM) kwizikhonkwane nr. 9, 10. Icala elichasayo lekhebula kufuneka lixhunywe kwisixhobo sangaphandle, ofuna ukusilawula / ukutshintshela kwi-relay.
11. Buyisela umva i-terminal cover (No. 1) kwi-Base part (No. 5). Qinisa isikrufu sokulungisa (3) kwaye ujonge ukuba isigqubuthelo setheminali (1) sivala ngokufanelekileyo.
12. Ukuba uMthengi ufuna ukusebenzisa i-RJ12 HAN / P1 interface output yangaphandle (No. 11) ngoko kufuneka ususe isigqubuthelo sothuli (16) kwi-HAN RJ12 socket (11) kwaye unokudibanisa i-RJ12 cable (B2) kwi izibuko.
13. Qinisa / nyusa ukwakhiwa kwemveliso ngokweemfuno:
    • Nyuka kumzila kaloliwe we-DIN oyi-35mm (ene-DIN-rail fastener ngasemva).
    • I-3-point fasting kunye nomngxuma ophezulu wokulungisa (14) kunye neendawo ezisezantsi zokulungisa (6) ngezikrufu - eludongeni okanye kwikhabhinethi yokukhanyisa uluntu.
14. Xhaka i ~ 207-253V AC amandla voltage kwiingcingo zamandla ze-AC ze-terminal input (iingcingo nr. 1, 2 – pinout: L (line), N (neutral)) umz kumthombo wamandla wangaphandle okanye iplagi yombane.

INKCAZELO YE-INTERFACE

UKUSEBENZA KWESIXHOBO

Ibhokisi ye-WM-Relay inesistim efakwe ngaphambili, eqala ngokukhawuleza ukusebenza emva kokongeza umthombo wamandla kwisixhobo.
Ukusebenza kwangoku kuya kusayinwa yi-LEDs yesimo (Nr.15), ngokwendlela yokuziphatha kwe-LED.
Isixhobo siphulaphule ibhasi ye-RS485 kwimiyalezo engenayo / imiyalelo yesixhobo esixhunyiwe kwi-port ye-RJ12 E-meter. Ukuba ifumana umyalezo osebenzayo, isixhobo siya kuphumeza umyalelo ongenayo (umzekelo, ukutshintshela kwi-relay) kwaye uthumele umyalezo kujongano lwe-HAN (isiphumo soMthengi we-RJ12).
Ngaxeshanye, i-relay efunekayo iya kutshintshelwa kwi-ON ngenxa yesicelo. (Kwimeko yokucinywa kwesicelo, i-relay iya kucinywa).
Iimpawu ze-LED (No. 15) ziya kuhlala zinolwazi malunga nomsebenzi wangoku.
Kwimeko yokususwa / ukuqhawulwa komthombo wamandla we-AC, ibhokisi yokubuyisela iya kucima ngokukhawuleza. Emva kokongeza umthombo wamandla kwakhona, iireyilayi ziya kutshintshela kwindawo yazo esisiseko, ekuthi OFF (ayitshintshi).
Ukufumana iinkcukacha ezithe vetshe funda iManuwali yokuFakela imveliso.

IMITHETHO EZILUMILEYO→ UKUQHELEKISWA KWEBHOKISI YOKUDLULA
Ukudluliselwa kwedatha kuvumela kuphela indlela enye (i-unidirectional) yokunxibelelana ukusuka kumitha ukuya kwi-WM-RelayBox (i-RJ12 i-e-meter connector input) kunye nonxibelelwano lwendlela enye ukusuka kwi-WMRelayBox ukuya kwi-Customer Interface output connector (eyodwa, i-RJ12 yangaphandle).

IMITHA ELULUMILEYO → UNXIBELELWANO NGEBHOKISI YONXIBELELWANO
Isixhobo siqhagamshelwe kwimitha yosetyenziso olukrelekrele ngomgca wentambo kwi-RS-485 ibhasi.
Ibhokisi ye-WM-Relay iqulethe iilayidi ezine ezitshintshiweyo ngabanye, ezisetyenziselwa ukulawula izixhobo ezixhunyiwe - ngokukodwa izixhobo zabathengi okanye nasiphi na esinye isixhobo (ukucima / ukuvala).
Ibhokisi le-WM-Relay linxibelelana kwaye lilawuleka kunye ne-DLMS / COSEM imiyalelo, efikelela kwibhokisi ye-relay ngendlela yonxibelelwano olungaqinisekanga ngemitha yokusetyenziswa edibeneyo.
Ukongeza kwimiyalelo ejoliswe ekulawuleni ibhokisi ye-relay, idatha ejoliswe ekuphumeni kwemitha yokusetyenziswa nayo ihanjiswa nge-interface yokusetyenziswa kwemitha.
Ibhokisi ye-WM-Relay iqulethe isidibaniso esahlukileyo esizimeleyo kunye nesinqunyanyisiweyo soqhagamshelwano lwemveliso yomthengi.
Injongo yesixhobo kukulawula izixhobo ezidityanisiweyo zomthengi.

Iimpawu ze-LED
PWR (AMAMANDLA): I-LED esebenzayo ngokubomvu kwimeko yobukho be ~ 230V AC voltage. Ukuze ufumane iinkcukacha ezithe vetshe jonga ngezantsi.
I-STA (STATUS): Ubume be-LED, danyaza ngokufutshane kube kanye ngokubomvu ekuqaleni. Ukuba isixhobo siya kufumana umyalezo / umyalelo osebenzayo kwibhasi ye-RS485 ngaphakathi kwemizuzu emi-5, iya kusayina unxibelelwano ngalo lonke ixesha ngokudanyaza okubomvu kwe-LED.
I-R1..R4 (UREYIMBO #1 .. ULUNQOSHO #4): I-LED ehambelana nayo iyasebenza (ukukhanyisa ngobomvu), xa i-relay yangoku iya kutshintshwa kwi-ON (i-RELAY yangoku ye-LED iya kuvulwa kwakhona - i-ligthing ngokuqhubekayo). Kwimeko ye-OFF (icinyiwe i-relay) i-LED ye-RELAY yangoku ye-LED ayiyi kuba nanto.
Ngaphaya koko, ulandelelwano oluneenkcukacha lwe-LED lunokufunyanwa kwaye lufundwe kwiNcwadi yoFakelo lwemveliso.

AMAPHEPHA & NENKXASO YEMVELISO

Imveliso webindawo (amaxwebhu, njl.): https://m2mserver.com/en/product/wm-relaybox/

Kwimeko yesicelo senkxaso yemveliso, cela inkxaso yethu kwi iotsupport@wmsystems.hu idilesi ye-imeyile okanye khangela inkxaso yethu webindawo yokufumana amanye amathuba oqhagamshelwano nceda: https://www.m2mserver.com/en/support/

Le mveliso iphawulwe ngesimboli se-CE ngokwemigaqo yaseYurophu.
Isimboli somgqomo ohlatyiweyo sithetha ukuba imveliso ekupheleni komjikelo wobomi bayo kufuneka ilahlwe nenkunkuma yasekhaya ngokubanzi kwiManyano yaseYurophu. Lahla kuphela izinto zombane/ze-elektroniki kwiinkqubo zokuqokelela ezahlukileyo, ezilungiselela ukufunyanwa nokuhlaziywa kwezinto eziqulethwe ngaphakathi. Oku akubhekiseli kuphela kwimveliso, kodwa nazo zonke ezinye izixhobo eziphawulwe ngesimboli esifanayo.

Amaxwebhu / Izibonelelo

I-RelayBox WM-RELAYBOX WM-RelayBox Innovation kwiiSmart IoT Systems [pdf] Isikhokelo somsebenzisi I-WM-RELAYBOX ye-WM-RelayBox Innovation kwii-Smart IoT Systems, i-WM-RELAYBOX, i-WM-RelayBox Innovation kwii-Smart IoT Systems, i-Innovation kwii-Smart IoT Systems, i-Smart IoT Systems, ii-IoT Systems, iiNkqubo ze-IoT.

Iimbekiselo

• Incwadi yokusebenzisa