ADA IZIXHOBO Cube 360 ​​Laser Level

IZILUMKISO

Inqanaba le-Laser i-ADA CUBE 360 imodeli - sisixhobo esisebenzayo kunye ne-multi-prism esenzelwe ukusebenza kwangaphakathi nangaphandle. Isixhobo sikhupha: umgca we-laser one-horizontal (i-angle ye-beam scan ye-360 °) umgca we-laser othe nkqo (i-angle ye-beam scan ye-110 °); phantsi point laser. Musa ukujonga umqa we-laser! Musa ukufaka isixhobo kwinqanaba lamehlo! Ngaphambi kokusebenzisa isixhobo, funda le ncwadana yokusebenza!

IIMFUNO ZOBUGCISA

INKCAZELO YOMSEBENZI
Ukukhupha umgca welaser othe tye kunye nothe nkqo. Ukuzilinganisa ngokukhawuleza: xa ukuchaneka komgca kuphuma kuluhlu umgca we-laser ukhanyisa kunye nesandi sesilumkiso siveliswa. Inkqubo yokutshixa imbuyekezo yothutho olukhuselekileyo. Inkqubo ephakathi yokutshixa imbuyekezo yokusebenza kwithambeka. Umsebenzi wokusebenza wangaphakathi nangaphandle.

IIMBONAKALO

1. Imigca yeLaser ivuliwe/ivaliwe
2. Indlela yokusebenza yangaphakathi/yangaphandle
3. Indawo yebhetri
4. Intaba ye-Tripod 1/4''
5. Ukutshintsha kwembuyekezo (ON/X/OFF)
6. Ifestile yelaser ethe nkqo
7. Ifestile yelaser ethe tyaba

INGCACISO

• Laser Umgca othe tye 360 ​​°/umgca othe nkqo
• Imithombo yokukhanya i-2 laser diode ene-laser emission wave wave ubude be-635 nm
• Iklasi yokhuseleko lweLaser Udidi 2, <1mW
• Ukuchaneka ±3 mm/10 m
• Uluhlu lokuzilinganisa ± 4 °
• Uluhlu olusebenzayo kunye / ngaphandle kommkeli 70/20 m
• Umthombo wamandla iibhetri ze-alkaline ezi-3, uhlobo lwe-AA
• Ixesha lokusebenza malunga. Iiyure ezili-15, ukuba yonke into ivuliwe
• Intambo yetripod 2х1/4”
• Ubushushu bokusebenza -5°C +45°C
• Ubunzima 390 g

IIMFUNO ZOKHUSELEKO NOKHATHALELO

Landela iimfuno zokhuseleko! Musa ukujongana kwaye ujonge kwi-laser beam! Inqanaba leLaser sisixhobo esichanekileyo, ekufuneka sigcinwe kwaye sisetyenziswe ngononophelo. Kuphephe ukungcangcazela kunye nokungcangcazela! Gcina i-Instrument kunye nezixhobo zayo kuphela Kwimeko yokuthwala. Kwimeko yokufuma okuphezulu kunye nobushushu obuphantsi, yomisa i-Instrument kwaye uyicoce emva kokusetyenziswa. Musa ukugcina i-Instrument kwiqondo lokushisa elingaphantsi kwe-20 ° C nangaphezulu kwe-50 ° C, ngaphandle koko i-Instrument ingaba ngaphandle kwesenzo. Musa ukubeka Isixhobo Kwityala lokuthwala Ukuba Isixhobo okanye ityala zimanzi. Ukunqanda ukufuma condensa-tion Ngaphakathi Instrument- yomisa ityala kunye laser

Isixhobo!
Jonga rhoqo Instrument uhlengahlengiso! Gcina ilensi icocekile kwaye yomile. Ukucoca i-Instrument sebenzisa i-napkin ethambileyo yomqhaphu!

UKUSEBENZA UKU-odola

ICube 360 ​​sisixhobo esithembekileyo nesifanelekileyo. Iya kuba sisixhobo esingenakubuyiselwa iminyaka emininzi.

1. Phambi kokusetyenziswa, susa isiciko sendawo yebhetri. Faka iibhetri ezintathu kwindawo yebhetri enepolarity eyiyo, emva koko ubuyisele isiciko.
2. 2. Seta i-comensator locking grip 5 ibe yi-ON isikhundla, iiplanga ezimbini ze-laser ziya kuvulwa. Ukuba utshintsho LUVULIWE, oko kuthetha ukuba umbane uvuliwe kwaye nombuyiseli uyasebenza. Ukuba i-switch 5 ikwindawo ephakathi, oko kuthetha ukuba amandla avuliwe, imbuyekezo isavaliwe, kodwa ayiyi kulumkisa ukuba ukhupha i-slope. Yindlela yesandla.
   Ukuba utshintsho 5 LUVALIWE, oko kuthetha ukuba isixhobo sicinyiwe, umbuyiseli naye utshixiwe.
3. Cinezela iqhosha 1 kanye kuphela- umqadi othe tye uya kuvulwa. Cinezela iqhosha 1 elinye ixesha elingakumbi - umqadi othe nkqo we-laser uya kuvulwa. Kwakhona cofa iqhosha 1 - imiqadi ethe tyaba kunye nethe nkqo iya kuvulwa.
4. Cofa iqhosha 2 kanye. Imo yangaphandle ivuliwe. Cofa iqhosha 2 elinye ixesha elingakumbi. Isixhobo siqala ukusebenza kwimodi yangaphakathi.

Ukujonga ukuchaneka kwenqanaba lelaser yomgca

Ukujonga ukuchaneka komgca welaser level (slope of plane)
Misa isixhobo phakathi kweendonga ezimbini, umgama u-5m. Vula iLaser Line, kwaye uphawule inqaku lomgca we-laser ophambanweni eludongeni. Jikelezisa isixhobo nge-180 ° kwaye uphawule inqaku lomgca we-laser wesiphambano eludongeni kwakhona. Misa isixhobo se-0,5-0,7m kude nodonga kwaye wenze, njengoko kuchazwe ngasentla, amanqaku afanayo. Ukuba umahluko {a1-b2} kunye {b1-b2} ungaphantsi kwexabiso "lokuchaneka" (jonga iinkcukacha), akukho mfuneko yokulinganisa. Eksample: xa ujonga ukuchaneka kweCross Line Laser umahluko ngu {a1-a2}=5 mm kunye {b1-b2}=7 mm. Impazamo yesixhobo: {b1-b2}-{a1-a2}=7-5=2 mm. Ngoku unokuthelekisa le mpazamo kunye nempazamo eqhelekileyo. Ukuba ukuchaneka kwenqanaba leLaser akuhambelani nokubango lokuchaneka, qhagamshelana neziko lenkonzo eligunyazisiweyo.

Ukukhangela inqanaba
Khetha udonga kwaye usete i-laser 5m kude nodonga. Vula i-laser kunye nomgca we-laser we-laser ubhalwe A eludongeni. Fumana enye inqaku M kumgca othe tye, umgama ujikeleze i-2.5m. I-Swivel laser, kunye nenye indawo enqamlezayo yomgca we-laser enqamlezayo iphawulwe B. Nceda uqaphele umgama we-B ukuya ku-A kufuneka ube yi-5m. Ukulinganisa umgama phakathi kwe-M ukuya kumgca welaser.

Ukujonga i-plumb
Khetha udonga kwaye usete i-laser 5m kude nodonga. Xhoma iloli yokulinganisa ubude be-2.5 m eludongeni. Vula i-laser kwaye wenze umgca we-laser othe nkqo uhlangane nenqaku le-plumb. Ukuchaneka komgca kuluhlu ukuba umgca othe nkqo awudluli (phezulu okanye ezantsi) ukuchaneka okuboniswe kwiinkcukacha (umz. ± 3mm/10m). Ukuba ukuchaneka akungqinelani nebango lokuchaneka, qhagamshelana neziko lenkonzo eligunyazisiweyo.

ISICELO

Lo mgangatho we-laser we-cross-line uvelisa i-laser beam ebonakalayo evumela ukwenza le milinganiselo ilandelayo: Ukulinganisa ubude, ukulinganisa iiplani ezithe tye kunye nezithe nkqo, ii-angles ezichanekileyo, indawo ethe nkqo yofakelo, njl njl. ukuseta amanqaku anguziro, okumakishwa ngaphandle kwebracing, ukufakwa kweentakumba, izikhokelo zephaneli, ukufaka iithayile, njl. njl. ukusebenza kwangaphandle kumgama phakathi koluhlu lokusebenza kwayo.

UKHUSELEKO LOKHUSELEKO

1. Ileyibhile yesilumkiso malunga neklasi yelaser kufuneka ibekwe kwisigqubuthelo segumbi lebhetri.
2. Musa ukujonga umqa we-laser.
3. Musa ukufaka umqadi we-laser kwinqanaba lamehlo.
4. Musa ukuzama ukuqhawula isixhobo. Kwimeko yokungaphumeleli, isixhobo siya kulungiswa kuphela kwiindawo ezigunyazisiweyo.
5. Isixhobo sihlangabezana nemigangatho yokukhupha i-laser.

INKONZO NOKUCOCA

Nceda uphathe ngenkathalo izixhobo zokulinganisa. Coca ngelaphu elithambileyo kuphela emva kokusetyenziswa. Ukuba kuyimfuneko damp ilaphu elinamanzi. Ukuba isixhobo simanzi sicoce kwaye somise ngononophelo. Yipakishe kuphela xa yome ngokupheleleyo. Uthutho kwisikhongozeli sokuqala/kwibhokisi kuphela. Qaphela: Ngexesha lothutho Vula/Vala isitshixo sembuyekezo (5) masisetelwe kwindawo ethi “OFF”. Ukungahoywa kunokukhokelela kumonakalo wembuyekezo.

IZIZATHU EZITHILE ZEZIPHUMO ZOMLINGANISO EZINGAPHUMELEKANGA

• Imilinganiselo ngeglasi okanye iifestile zeplastiki;
• Ifestile yokukhupha i-laser emdaka;
• Emva kokuba isixhobo siwisiwe okanye sibethiwe. Nceda ujonge ukuchaneka.
• Ukuguquguquka okukhulu kobushushu: ukuba isixhobo siya kusetyenziswa kwiindawo ezibandayo emva kokuba sigcinwe kwiindawo ezishushu (okanye ngenye indlela) nceda ulinde imizuzu embalwa ngaphambi kokuba wenze imilinganiselo.

ELECTROMAGNETIC ACCEPTABILITY (EMC)

• Akunakukhutshelwa ngaphandle ngokupheleleyo ukuba esi sixhobo siya kuphazamisa ezinye izixhobo (umz. iinkqubo zokukhangela);
• iya kuphazanyiswa zezinye izixhobo (umzekelo, iradiation ye-electromagnetic radiation ekufutshane neendawo zoshishino ezikufutshane okanye ii-radio transmitters).

LASER UHLELO
Isixhobo yi-laser class 2 laser imveliso ngokuhambelana ne-DIN IEC 60825-1: 2007. Kuvunyelwe ukusebenzisa iyunithi ngaphandle kokhuseleko olongezelelweyo.

IMIYALELO YOKHUSELEKO

• Nceda ulandele imiyalelo enikwe kwincwadana yemigaqo yabasebenzisi.
• Musa ukujonga kwi-beam. I-laser beam ingakhokelela ekulimazeni kwamehlo (nokuba ukusuka kumgama omkhulu).
• Musa ukujolisa imiqadi yelaser ebantwini okanye kwizilwanyana.
• Inqwelomoya yelaser kufuneka imiswe ngaphezu kwenqanaba lamehlo abantu.
• Sebenzisa isixhobo sokulinganisa imisebenzi kuphela.
• Musa ukuvula indlu yesixhobo. Ulungiso kufuneka lwenziwe ngoomasifundisane abagunyazisiweyo kuphela. Nceda uqhagamshelane nomthengisi wakho wasekuhlaleni.
• Musa ukususa iilebhile ezilumkisayo okanye imiyalelo yokhuseleko.
• Gcina izixhobo kude ebantwaneni.
• Musa ukusebenzisa izixhobo kwindawo eziqhumayo.

ISIQINISEKISO

Le mveliso iqinisekisiwe ngumvelisi kumthengi wokuqala ukuba ingabinaziphene kwizinto eziphathekayo kunye nokusebenza phantsi kokusetyenziswa okuqhelekileyo kwithuba leminyaka emibini (2) ukususela kumhla wokuthenga. Ngexesha lewaranti, naphezu kobungqina bokuthenga, imveliso iya kulungiswa okanye itshintshwe (ngemodeli efanayo okanye efanayo kwinketho yomenzi), ngaphandle kwentlawulo kuyo nayiphi na inxalenye yabasebenzi. Xa kukho isiphene nceda uqhagamshelane nomthengisi apho wawuthenge khona le mveliso. Iwaranti ayizukusebenza kule mveliso ukuba isetyenziswe kakubi, isetyenziswe kakubi, okanye itshintshiwe. Ngaphandle kokunciphisa oku kungasentla, ukuvuza kwebhetri, kunye nokugoba okanye ukuwisa iyunithi kucingelwa ukuba ziziphene ezibangelwa kukusetyenziswa kakubi okanye impatho-gadalala.

OKUNGEZANTSIYO KUXANDUVA
Umsebenzisi wale mveliso kulindeleke ukuba alandele imiyalelo enikwe kwincwadana yemigaqo. Nangona zonke izixhobo zishiye indawo yethu yokugcina ikwimeko egqibeleleyo kunye nohlengahlengiso umsebenzisi ulindeleke ukuba ahlole amaxesha ngamaxesha ukuchaneka kwemveliso kunye nokusebenza ngokubanzi. Umenzi, okanye abameli bakhe, akathabathi xanduva lweziphumo zokusetyenziswa kakubi okanye ngabom okanye ukusetyenziswa kakubi kubandakanya nawuphi na umonakalo othe ngqo, ongathanga ngqo, osisiphumo, kunye nelahleko yengeniso. Umvelisi, okanye abameli bakhe, akathwali xanduva ngomonakalo osisiphumo, kunye nelahleko yenzuzo ngayo nayiphi na intlekele (inyikima, isaqhwithi, izandyondyo ...), umlilo, ingozi, okanye isenzo somntu wesithathu kunye/okanye ukusetyenziswa kwezinye iimeko ngaphandle kwesiqhelo. . Umenzi, okanye abameli bakhe, akathathi xanduva kuwo nawuphi na umonakalo, kunye nokulahlekelwa kwenzuzo ngenxa yokutshintsha kwedatha, ukulahleka kwedatha kunye nokuphazamiseka kweshishini, njl., okubangelwa ukusebenzisa imveliso okanye imveliso engasebenzisekiyo. Umenzi, okanye abameli bakhe, akathathi xanduva ngawo nawuphi na umonakalo, kunye nelahleko yenzuzo ebangelwa kusetyenziso ngaphandle kwezo zichazwe kwincwadi yabasebenzisi. Umenzi, okanye abameli bakhe, akathathi xanduva lomonakalo owenziwe yintshukumo engalunganga okanye isenzo ngenxa yokunxibelelana nezinye iimveliso.

ISIQINISEKISO AYANDULI EKULANDELWENI KWAMATYALA

1. Ukuba umgangatho okanye inombolo yothotho iya kutshintshwa, icinywe, isuswe, okanye ingafundeki.
2. Ukugcinwa kwamaxesha athile, ukulungiswa okanye ukutshintsha iindawo ngenxa yokuphuma kwazo okuqhelekileyo.
3. Konke ukulungelelaniswa kunye nokuguqulwa ngenjongo yokuphucula kunye nokwandiswa kwendawo eqhelekileyo yokusetyenziswa kwemveliso, ekhankanywe kumyalelo wenkonzo, ngaphandle kwesivumelwano esibhaliweyo somnikezeli weengcali.
4. Inkonzo eyenziwa nguye nabani na ngaphandle kweziko lenkonzo eligunyazisiweyo.
5. Ukonakaliswa kweemveliso okanye iindawo ezibangelwa kukusetyenziswa kakubi, kubandakanywa, ngaphandle kokunciphisa, ukusetyenziswa kakubi okanye ukungahoywa kwemigaqo yomyalelo wenkonzo.
6. Iiyunithi zokubonelela ngombane, iitshaja, izincedisi, kunye namalungu okunxiba.
7. Iimveliso, ezonakaliswe ngokuphathwa kakubi, ukulungiswa okungalunganga, ukugcinwa kwezinto ezinomgangatho ophantsi kunye nezingekho eziqhelekileyo, ubukho balo naluphi na ulwelo kunye nezinto zangaphandle ngaphakathi kwemveliso.
8. Imisebenzi kaThixo kunye/okanye izenzo zomntu wesithathu.
9. Kwimeko yokulungiswa okungafunekiyo kude kube sekupheleni kwexesha lewaranti ngenxa yomonakalo ngexesha lokusebenza kwemveliso, kukuthutha kunye nokugcinwa, iwaranti ayiqhubeki.

IKHADI LEWARanti

• Igama kunye nemodeli yemveliso _________________________________________________
• Inombolo yothotho ________________umhla we
• intengiso________________________________
• Igama lombutho wezorhwebo ____________________stamp yombutho wezorhwebo

Ixesha lewaranti yokusetyenziswa kwesixhobo ziinyanga ezingama-24 emva komhla wokuthengwa kwentengiso yokuqala. Ngeli xesha lewaranti, umnini wemveliso unelungelo lokukhulula ukulungisa isixhobo sakhe xa kukho iziphene zokuvelisa. Iwaranti isebenza kuphela ngekhadi lokuqala lewaranti, lizaliswe ngokupheleleyo kwaye licacile (stamp okanye uphawu lomthengisi lunyanzelekile). Uviwo lobugcisa lwezixhobo zokuchongwa kwempazamo phantsi kwewaranti lwenziwa kuphela kwiziko lenkonzo eligunyazisiweyo. Akukho mcimbi umenzi uya kuba noxanduva phambi komxhasi ngomonakalo othe ngqo okanye osisiphumo, ilahleko yenzuzo okanye nawuphina omnye umonakalo owenzeka ngenxa yesixhobo.tage. Imveliso ifunyenwe kwimeko yokusebenza, ngaphandle komonakalo obonakalayo, ngokupheleleyo. Icikidekile phambi kwam. Andinazikhalazo malunga nomgangatho wemveliso. Ndiqhelene neemeko zenkonzo yewaranti kwaye ndiyavuma.

• umsayini womthengi _______________________________

Ngaphambi kokuba usebenze kufuneka ufunde imiyalelo yenkonzo! Ukuba unayo nayiphi na imibuzo malunga nenkonzo yewaranti kunye nenkxaso yobugcisa qhagamshelana nomthengisi wale mveliso

Isiqinisekiso sokwamkelwa kunye nokuthengiswa

igama kunye nomzekelo wesixhobo

• Ingqinelana ne- ______ ukutyunjwa kweemfuno ezisemgangathweni kunye nezobugcisa
• Umhla wokukhutshwa _______Stamp yesebe lolawulo lomgangatho
• Ixabiso
• Ithengisiwe
• Umhla wokuthengisa
• igama lendawo yorhwebo

Amaxwebhu / Izibonelelo

	ADA IZIXHOBO Cube 360 ​​Laser Level [pdf] Incwadi yokusebenzisa I-CUBE 360, iNqanaba leLaser, iCUBE 360 iNqanaba leLaser, iNqanaba
	ADA IZIXHOBO Cube 360 ​​Laser Level [pdf] Incwadi Yomyalelo I-CUBE 360 iNqanaba leLaser, iCUBE 360, iNqanaba leLaser yeCUBE, iNqanaba leLaser ye-360, iNqanaba leLaser

Iimbekiselo

• Incwadi yokusebenzisa