vtech CTM-A2315-SPK 1 Line Trim Style Corded Analog Phone User Guide

Avoid placing the product near water sources or on unstable surfaces.
Ensure proper ventilation by not blocking slots and openings on the telephone base and handset.

Operate the product only from the specified power source mentioned on the label.
Avoid overloading wall outlets and extension cords.

Do not disassemble the product; seek service from an authorized facility if needed.
Avoid using the telephone during electrical storms.

Wall Mounting Instructions

To mount the telephone base on the wall, align the eyelets with the mounting studs of the wall plate. Slide the base down on both studs until it locks into place.

Refer to the full instructions in the Installation section of the user manual for detailed steps.

Handset Usage

Only place the handset next to your ear when it is in normal talk mode to avoid any risks.
Do not push objects into the slots of the telephone base or handset to prevent dangerous voltage points or short circuits.

Important safety instructions

The applied nameplate is located at the bottom or rear of the product.
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and injury, including the following.

This product should be installed by a qualiﬁed technician.
Read and understand all instructions.

Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Do not use this product near water, such as near a bathtub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.
Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug.
- This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply on the premises, consult your dealer or local power company.
Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.
Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.
To reduce the risk of electric shock, do not disassemble this product but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than speciﬁed access doors may expose you to dangerous voltages or other risks. Incorrect reassembly can cause an electric shock when the product is subsequently used.
Do not overload wall outlets and extension cords.
Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:
- When the power supply cord or plug is damaged or frayed.
- If liquid has been spilled onto the product.
- If the product has been exposed to rain or water.
- If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.
- If the product has been dropped and the telephone base and/or handset has been damaged.
- If the product exhibits a distinct change in performance.
Avoid using a telephone (other than a cordless one) during an electrical storm. There is a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark may be created when the adapter is plugged into the power outlet or when the handset is replaced in its cradle. This is a common event associated with the closing of any electrical circuit. The user should not plug the phone into a power outlet and should not put a charged handset into the cradle if the phone is located in an environment containing concentrations of flammable or flame-supporting gases unless there is adequate ventilation. A spark in such an environment could create a ﬁre or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
Only put the handset of your telephone next to your ear when it is in normal talk mode.
The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a ﬁre. They may explode. Check with local codes for possible special disposal instructions.

In the wall mounting position, make sure to mount the telephone base on the wall by aligning the eyelets with the mounting studs of the wall plate. Then, slide the telephone base down on both mounting studs until it locks into place. Refer to the full instructions in Installation in the user’s manual.

CAUTIONS Keep small metallic objects, such as pins and staples, away from the handset receiver.
SAVE THESE INSTRUCTIONS

Parts checklist

Items contained in the respective corded telephone package:

Telephone layout

Handset

Design is subject to change without prior notice.

Base

1	MESSAGE WAITING LED
2	Wall mount clip
3	Faceplate and overlay
4	Ringer tone switch
5	Voicemail voltage detection
6	Telephone line jack
7	Coiled handset cord jack
8	Grooves for base stand

Installation

Telephone base installation Installation option – desktop position

Turn the telephone base over with the bottom side facing up. Insert the base stand into the lower grooves on the telephone base until they lock securely, as shown below.

Connect both the telephone line and coiled handset cord to the telephone base and route them along the wire ducts accordingly. Install the telephone base, as shown below.

Set up

Default settings are indicated by asterisks (*).

Setting	Options	Adjustable by
Handset earpiece volume	1, 2*, 3	User and administrator
Speakerphone volume	1, 2, 3, 4*, 5, 6	User and administrator
Ringer tone	Tone 1*, Tone 2, Tone 3	Administrator only
Voicemail voltage detection	Disable voicemail voltage detection, Periodic low voltage pulse detection method, Steady high voltage and periodic high voltage pulse detection method	Administrator only

Ringer tone

There are 3 ringer tone options.

To change the ringer tone

Turn the telephone base over with the bottom side facing up. Remove the sticker above the voicemail voltage detection sticker.
Use a narrow object such as a standard screwdriver to slide the ringer tone switch (on the left, in the middle or on the right) as shown below to select the desired detented position

Put the sticker back in place.

Voicemail voltage detection

There are 3 options to set the voicemail voltage detection on the telephone base.

To disable the voicemail voltage detection

Turn the telephone base over with the bottom side facing up. Remove the sticker above the telephone line jack.
Use a narrow object to unplug all the jumpers from the telephone base.

Put the sticker back in place.

To set the voicemail voltage detection by the periodic low voltage pulse detection method

Turn the telephone base over with the bottom side facing up. Remove the sticker above the telephone line jack.

Use a narrow object to unplug all the jumpers from the telephone base. Then, plug the jumpers into 1,2 and 3.
Put the sticker back in place.

To set the voicemail voltage detection by the steady high voltage and periodic high voltage pulse detection method

Turn the telephone base over with the bottom side facing up. Remove the sticker above the telephone line jack.
Use a narrow object to unplug all the jumpers from the telephone base. Then plug the jumpers into 1,2, and 3.
Put the sticker back in place.

Speed Dial keys

There are 4 programmable guest-service (Speed Dial) keys, including programmable key #1, programmable key #2, EMERGENCY and MESSAGES.
Program these keys to automatically dial telephone numbers or to activate telephone system features.

The PROGRAM key and the PAUSE key are embedded under the speed dial keys’ sticker cover, as shown below.

To remove the speed dial key sticker cover

Use a narrow object such as a mini screwdriver or a paper clip to slide into the tiny semi-circle hole on the bottom of the sticker cover.

Pry open the speed dial key sticker cover, and you will hear a “click” sound when the cover is detached from the telephone base.

To program a Speed Dial key

Lift the corded handset. Then, press the recessed PROGRAM key to enter the administrator mode.

Press the desired Speed Dial key where the telephone number is to be stored.
Enter the telephone number (up to 16 digits in length).
- To insert a pause in the stored number, press the recessed PAUSE key.

The telephone stores the number automatically when 16 digits are entered. When the number has less than 16 digits, press the recessed PROGRAM key again. You hear 3 rising beeps as conﬁrmation.

To clear the programmed Speed Dial key

Lift the corded handset. Then, press the recessed PROGRAM key to enter the administrator mode.

Press the Speed Dial key where the telephone number is to be deleted. Then, press the recessed PROGRAM key again. You hear 3 rising beeps as conﬁrmation.

Operation

Receive a call

When there is an incoming call, the telephone rings and the MESSAGE WAITING LED flashes.

Answer a call:

Lift the corded handset from the telephone base to answer or press /SPEAKER.
The/SPEAKER key illuminates when in use.

Place a call

Lift the corded handset from the telephone base or press/SPEAKER. Listen for a dial tone, and then dial the desired number.
The/SPEAKER key illuminates when in speakerphone mode.

End a call

Place the corded handset in the telephone base or press/SPEAKER when in speakerphone mode.

Volume

The listening volume can be adjusted from the corded handset, whereas the ringer volume cannot be adjusted.

Adjust the listening volume

During a call, press VOL+/- to adjust the listening volume. The next call returns to the default listening volume.

Speakerphone

During a call, press/SPEAKER to switch a call between the corded handset earpiece and the speakerphone.
- Press/SPEAKER again to switch back to the corded handset earpiece.
- The/SPEAKER key illuminates when in use.
In idle mode, press/SPEAKER to activate the speakerphone mode and /SPEAKER key will illuminate when in speakerphone mode.

Mute

Mute the microphone

During a call, press MUTE.
- The MUTE key illuminates when the mute function is turned on. You can hear the party on the other end, but they cannot hear you.

Press MUTE again to resume the conversation.
- The light on the MUTE key turns off.

Play messages

Press MESSAGES in idle mode to play messages.

Appendix

Troubleshooting

If you have difficulty with the telephones, please try the suggestions below. For customer service, visit our website at www.vtechhotelphones.com or call 18889072007.

For corded telephone

VTech Hospitality Limited Warranty

Program

VTech Communications, Inc., the manufacturer of VTech Hospitality Product (“Product”), warrants to the holder of a valid proof of purchase (“end user” or “you”) that the Product and all accessories provided by VTech in the Product’s package are free from defects in material and workmanship, under the following terms and conditions, when installed and used normally and under the Product’s operating instructions.

The limited warranty extends to the end user of this Product and applies only if such Product is purchased through a United States of America and/or Canadian distributor.
The limited warranty period for this Product is determined based on the following:

5 Years – Analog Models

All Classic Models – corded and cordless
All Contemporary Models – corded and cordless
All TrimStyle Models

2 Years – SIP Non-Display Models

All Classic Models – corded and cordless
All Contemporary Models – corded and cordless

All TrimStyle Models
During the limited warranty period, VTech’s authorized service representative will replace, at VTech’s option, without charge, a Product that is not free from defects in materials and workmanship.
If the Product is replaced, it may be replaced with a new or refurbished Product of the same or similar design. Replacement of the Product, at VTech’s option, is the exclusive remedy.

The limited warranty period for the Product begins on the date that the end user takes possession of the Product. This limited warranty also applies to replacement Products for a period of either (a) 90 days from the date the replacement Product is shipped to you or (b) the time remaining on the original limited warranty as described above, whichever is longer.

This limited warranty does not cover:

Product or parts that have been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, ﬁre, water or other liquid intrusion; or

Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized service representative of VTech; or
Product to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or
Product to the extent that the problem is caused by use with non-VTech accessories; or

Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or
Products purchased, used, serviced, or shipped for repair from outside the United States or Canada, or used for non-approved commercial or institutional purposes (including but not limited to Products used for rental purposes); or
Product returned without valid proof of purchase; or

Charges or costs incurred by the end user and risk of loss or damage in removing and shipping the Product or for installation or set-up, adjustment of customer controls, and installation or repair of systems outside the unit.
Line cords or coil cords, plastic overlays, connectors, power adapters and batteries, if the Product is returned without them. VTech will charge the end user at the then-current prices for each of the missing items.
NiCd or NiMH handset batteries, or power adapters, which, under all circumstances, are covered by a one (1) year warranty only.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of Product(s) to the service location.
VTech’s authorized service representative will return the replaced product under this limited warranty to you, with transportation, delivery and handling charges prepaid. VTech assumes no risk for damage or loss of the Product in transit.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech.
It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product, whether express or implied, oral or written, or statutory.
The warranty exclusively describes all of VTech’s responsibilities regarding the Product. No one is authorized to make modiﬁcations to this warranty, and you should not rely on any such modiﬁcation.

VTech’s liability to the end user hereunder shall not exceed the purchase price of the Product. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost proﬁts or revenue, inability to use the product, or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you speciﬁc legal rights, and you also have other rights, which vary from state to state or province to province.

FCC

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference,
This device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identiﬁer in the format US: AAAKXNANXXXX. This identiﬁer must be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line. See the installation instructions in the user manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be ﬁve (5.0) or less. For more information, please contact your telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone service provider or a qualiﬁed installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected.
If this equipment is causing harm to the telephone network, your telephone service provider may temporarily discontinue your telephone service. Your telephone service provider is required to notify you before interrupting service. If advance notice is
not practical, you will be notiﬁed as soon as possible. You will be allowed to correct the problem, and your telephone service provider is required to inform you of your right to ﬁle a complaint with the FCC. Your telephone service provider may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. Your telephone service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, ﬁre, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
When the adjunct is used with a leased system, permission of the owner of the equipment must be obtained for connection of the adjunct because modiﬁcation of the host system is often required.
This product can only be connected to the host equipment and never directly to the network.

Industry Canada

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations. The Ringer Equivalence Number (REN) is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed ﬁve.

ISEDC Warning

This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

Privacy of communications may not be ensured when using this telephone.

Operating range

The cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC).
Even so, the cordless handset and telephone base can communicate over only a certain distance – which can vary with the locations of the telephone base, cordless handset, the weather, and the layout of the hotel.
When the cordless handset is out of range while on a call, the cordless handset rapidly beeps three times.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect well when you answer the call. Move closer to the telephone base to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference.
To improve reception, move closer to the telephone base.

Maintenance

Taking care of your telephone

Your telephone contains sophisticated electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain or handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electrical appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many years.
Clean it only with a soft cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product. VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss caused by the deletion of data as a result of malfunction.
Be sure to make backup copies of important data on other media to protect against data loss.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road., Suite 555, Tigard, OR 97223, United States
Phone: 18889072007
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water.
If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND/OR TELEPHONE LINE CORD FROM THE WALL. Then, remove the telephone by the unplugged cords.

Technical specifications

1-Line Trimstyle Corded Analog Phone – CTM-A2315-SPK

Power requirement Line powered 24V or 48V (Loop Current: >18mA@Off-Hook mode)
Message waiting signal: Steady/periodic high voltage pulse or periodic low voltage pulse
Speed Dial memory Telephone handset: up to 4 memory locations; up to 16 digits
Size Telephone base: 174.8 x 74.5 x 48.8 mm
Corded handset: 212.9 x 48.4 x 42 mm
Specifications are subject to change without notice.
VTech Telecommunications, Inc.
CTM-A2315-SPK_UG_V1_CEC_US_3DEC2024

FAQ

Q: Can I clean the product with liquid cleaners?
- A: No, it is recommended to use a damp cloth for cleaning and avoid liquid or aerosol cleaners.
Q: Can I use the telephone during an electrical storm?
- A: It is advised to avoid using any telephone, other than a cordless one, during an electrical storm due to a remote risk of electric shock from lightning.

Documents / Resources

vtech CTM-A2315-SPK 1 Line Trim Style Corded Analog Phone [pdf] User Guide
CTM-A2315-SPK 1 Line Trim Style Corded Analog Phone, CTM-A2315-SPK, 1 Line Trim Style Corded Analog Phone, Corded Analog Phone, Analog Phone

References

User Manual

VTech CTM-A2315-SPK 1 Line Trim Style Corded Analog Phone

Product Information

Product Usage Instructions