STM32Cube IoT tuguni BLE Function Pack foydalanuvchi qoʻllanmasi

Dasturiy ta'minotga qo'yiladigan talablar:
Compatible with STM32 Nucleo development boards, specificallyNUCLEO-F401RE, NUCLEO-L476RG, or NUCLEO-U575ZI-Q.

Qo'shimcha ma'lumot:
For firmware updates, refer to the latest information available at www.st.com.

Mahsulotdan foydalanish bo'yicha ko'rsatmalar

Sozlash va demo Examples

1-qadam: Uskunani sozlash
Connect the VL53L3CX-SATEL breakout board to an STM32 Nucleo development board (NUCLEO-F401RE, NUCLEO-L476RG, or NUCLEO-U575ZI-Q) using the appropriate connectors.

2-qadam: Dasturiy ta'minotni sozlash
Ensure that the necessary software prerequisites are installed on your system as specified in the documentation.

3-qadam: demo Examples
Taqdim etilgan demoga qarangamples to understand how to interact with the VL53L3CX sensor using the provided software architecture.

Uskuna va dasturiy ta'minot tugadiview

Sample implementations are available for STM32 Nucleo development boards plugged into STM32 Nucleo expansion boards:

NUCLEO-F401RE (or NUCLEO-L476RG or NUCLEO-U575ZI-Q) + X-NUCLEO-BNRG2A1 + X-NUCLEO-53L3A2
NUCLEO-F401RE (or NUCLEO-L476RG or NUCLEO-U575ZI-Q) + X-NUCLEO-BNRG2A1 + X-NUCLEO-53L3A2

Bluetooth kam energiya kengaytirish platasi

Uskuna tavsifi

The X-NUCLEO-BNRG2A1 is a Bluetooth Low Energy (BLE) evaluation and development board system, designed around ST’s BLUENRG-M2SP Bluetooth Low Energy module based on BlueNRG-2.
The BlueNRG-2 processor hosted in the BLUENRG-M2SP module communicates with the STM32 microcontroller, hosted on the Nucleo development board, through an SPI link available on the Arduino UNO R3 connector.

Bortdagi asosiy mahsulot

BLUENRG-M2SP Bluetooth Low Energy, FCC and IC certified (FCC ID: S9NBNRGM2SP, IC: B976C-BNRGM2SP), module based on Bluetooth® Low Energy wireless network processor BlueNRG-2, BLE v5.0 compliant.
BLUENRG-M2SP integrates a BALF-NRG-02D3 balun and a PCB antenna. It embeds a 32 MHz crystal oscillator for the BlueNRG-2.

M95640-RMC6TG 64-Kbit serial SPI bus EEPROM with high-speed clock interface

X- NUCLEO-53L1A2 Hardware Description

The X-NUCLEO-53L3A2 is a ranging sensor with multi-target detection evaluation and development board designed around the VL53L3CX sensor based on ST FlightSense Time-of-Flight technology.

VL53L3CX Arduino UNO R32 ulagichida mavjud bo'lgan I2C havolasi orqali STM3 Nucleo ishlab chiquvchi platasi xost mikrokontrolleri bilan bog'lanadi.

Bortdagi asosiy mahsulot

VL53L3CX Time-of-Flight (ToF) ranging sensor with multi-target detection
0.25, 0.5, and 1mm spacers to simulate air gaps, with the cover glass

Cover window (made by Hornix) sample with low cross-talk,k ready to use / clipable on VL53L3CX
Two VL53L3CX breakout boards

VL53L3CX-SATEL Uskuna tavsifi

The VL53L3CX-SATEL breakout boards can be used for easy integration into customer devices. Thanks to the voltage regulyator va daraja o'zgartirgichlar, u 2.8 V dan 5 V gacha bo'lgan har qanday dasturda ishlatilishi mumkin.

The PCB section supporting the VL53L3CX module is perforated so that developers can break off the mini-PCB for use in a 2.8 V supply application using flying leads.

Bortdagi asosiy mahsulot

VL53L3CX Time-of-Flight (ToF) ranging sensor with witmulti-targetet detection
Regulator: 5 to 2.8 V range input voltage (chiqish jildtage: 2.8 V)

VL53L3CX signal interface level shifter

Muhim apparat qo'shimcha ma'lumot

BlueNRG-2 library does not work with the stock firmware that is loaded in the BLE module of the X-NUCLEO-BNRG2A1 expansion board.
Shu sababli:

First of all, it is needed to solder on X-NUCLEO-BNRG2A1; if it is not soldered, a 0-ohm resistor at R117.

Then you can use a standard ST-Link V2-1 with 5 jumper wires female-female together with the TSW-BNRGFLASHER software tool (currently available only for Windows PC) to update the firmware of the BLE module of X-NUCLEO-BNRG2A1.

Rasmda ko'rsatilganidek, X-NUCLEO-BNRG12A2 ning J1 pinlarini ST-Link V2-1 pinlariga ulashingiz va keyingi slaydda ko'rsatilgan amallarni bajarishingiz kerak.
In particular, we have the following connections:

	J12	ST-Link V2-1
Pin	1	1
Pin	2	9
Pin	3	12
Pin	4	7
Pin	5	15

Install the ST BlueNRG-1_2 Flasher Utility and open it, then select the SWD tab.b
Erase the flash memory of the BlueNRG-2 chip.
Download the Link Layer Only firmware for the BLE module from the following link: DTM_LLOnly. binn

Load the Link Layer Only firmware in the ST BlueNRG-1_2 Flasher Utility and then press the “Flash” button.
If you need to restore the stock firmware of the BLE module of X-NUCLEO-BNRG2A1, you can repeat the procedure using this firmware image DTM_Full.bi.n

If you should find some issues during the update process, you can try to repeat the procedure closing the J15 jumper on the X-NUCLEO-BNRG2A1 expansion board.

	VL53L3CX-SATEL	Arduino ulagichi	NUCLEO-F401RE NUCLEO-L476RG	NUCLEO-U575ZI-Q
SCL	2	D15	PB8	PB8
SDA	4	D14	PB9	PB9
XSDN	3	D4	PB5	PF14
VDD_SENSOR	5	3V3	CN6 pin n. 4	CN8 pin n. 7
GND_X	6	GND	CN6 pin n. 6	CN8 pin n. 11

Dastur tavsifi

The FP-SNS-FLIGHT1 is an STM32Cube function pack, which lets your IoT node connect to a smartphone via BLE and uses a suitable Android or iOS application like the STBLESensor app to view Parvoz vaqti sensori tomonidan o'qiladigan real vaqtda ob'ekt masofasi ma'lumotlari.

The package also enables advanced functions, such as presence detection within a fixed range.
This package, together with the suggested combination of the STM32 and ST devices, can be used to develop wearable applications or smart thing applications in general.
The software runs on the STM32 microcontroller and includes all the necessary drivers to recognize the devices on the STM32 Nucleo development board.

Asosiy xususiyatlar

Complete firmware to develop an IoT node with BLE connectivity, and Time-of-Flight sensors
Compatible with STBLESensor application for Android/iOS to perform distance data reading and firmware update (FOTA)
Multitarget ranging sensor application based on the VL53L3CX Time-of-Flight (ToF) sensor
Sample implementation available for X-NUCLEO-53L3A2 (or VL53L3CX-SATEL) and X-NUCLEO-BNRG2A1 connected to a NUCLEO-F401RE or NUCLEO-L476RG or NUCLEO-U575ZI-Q
Compatible with STM32CubeMX, can be downloaded from and installed directly into STM32CubeMX
STM32Cube tufayli turli MCU oilalarida oson ko'chirish
Foydalanuvchi uchun bepul litsenziya shartlari

Sozlash va demo Examples

Dasturiy ta'minot va boshqa shartlar

STSW-LINK004
- STM32 ST-LINK Utility (STSW-LINK004) is a full-featured software interface for programming STM32 microcontrollers
FP-SNS-PRISH1
- .zip faylidan nusxa oling file content of the firmware package into a folder on your PC.
- To'plam manba kodini o'z ichiga oladi, examples (Keil, IAR, STM32CubeIDE) compatible with NUCLEO-F401RE, NUCLEO-L476RG, NUCLEO-U575ZI.
ST BLE Sensor
Application for Android (V5.2.0 or higher) /iOS (V5.2.0 or higher) to download from Google Store / iTunes

O'rnatish tugadiview: Kengaytirish platalari bilan STM32 Nucleo

O'rnatish tugadiview

STM32 Nucleo kengaytirish platalari bilan HW uchun zaruriy shartlar

1 x Bluetooth Low Energy expansion board (X-NUCLEO-BNRG2A1)
1 x STM32 ranging sensor expansion board (X-NUCLEO-53L3A2 or VL53L3CX-SATEL)
1 x STM32 Nucleo development board (NUCLEO-U575ZI-Q or NUCLEO-F401RE or NUCLEO-L476RG)
1x Android or iOS device
1 x PC with Windows 10 and above
1x USB type A to Mini-B USB cable for NUCLEO-F401RE or NUCLEO-L476RG

1x USB type A to Micro-B USB cable for NUCLEO-U575ZI-Q

Bir necha daqiqada kodlashni boshlang (1/3)

Bir necha daqiqada kodlashni boshlang (2/3)

How to install the pre-compiled binary:
- For each application, there is inside the package one folder called “Binary”

Unda:

NUCLEO-F401RE va NUCLEO-L476RG uchun:
- pre-compiled FP-SNS-FLIGHT1 FW that could be flashed to a supported STM32 Nucleo for X-NUCLEO-53L3A2 using the STM32CubeProgrammer at the right position (0x08004000)
- Important Note: This pre-compiled binary is compatible with the FOTA update procedure
- pre-compiled FP-SNS-FLIGHT1 + BootLoader FW that could be directly flashed to a supported STM32 Nucleo for X-NUCLEO-53L3A2 using the STM32CubeProgrammer or by doing “Drag & Drop”
- Important Note: This pre-compiled binary is not compatible with the FOTA update procedure
- pre-compiled FP-SNS-FLIGHT1 FW that could be directly flashed to a supported STM32 Nucleo for VL53L3CX-SATEL using the STM32CubeProgrammer or by doing “Drag & Drop”

NUCLEO-U575ZI-Q uchun:
- pre-compiled FP-SNS-FLIGHT1 could be directly flashed to a supported STM32 Nucleo (for X-NUCLEO-53L3A2 and for VL53L3CX-SATEL) using the STM32CubeProgrammer or by doing “Drag & Drop”.
- Important Note: For the first installation, after the full flash erase (suggested procedure), use the STM32CubeProgrammer to set the STM32 MCU user byte settings to use bank 1 for flashing the firmware and start the application

How to install the code after compiling the project for NUCLEO-F401RE and NUCLEO-L476RG:

Compile the project with your preferred IDE

In the folder Utilities, there is a script *.sh that performs the following operations:

Full Flash Erase
Flash the right BootLoader at the right position (0x08000000)
Flash the FLIGHT1 firmware at the right position (0x08004000)
- This is the firmware that was compiled with the IDE
- This firmware is compatible with the FOTA update procedure
Save a complete Binary FW that includes both FLIGHT1 and the BootLoader
- This binary can be directly flashed to a supported STM32 board using the ST-Link or by doing “Drag & Drop.”
- Important Note:Thiss additional pre-compiled binary is not compatible with the FOTA update procedure

Before executing the *.sh script, it is necessary to edit it to set the installation path for STM32CubeProgrammer.
BootLoaderPath and BinaryPath as input are required when executing the .sh script.

Flash boshqaruvi va yuklash jarayoni

Bluetooth kam energiya va sensorlar uchun dasturiy ta'minot

NUCLEO-F1RE / NUCLEO-L401RG / NUCLEO-U476ZI-Q uchun FP-SNS-FLIGHT575 – Seriyali liniya monitori (egTera Term)

Demo Examples ST BLE Sensor ilovasi tugadiview

Android/iOS uchun ST BLE Sensor ilovasi (1/5)

Hardware Features – Android Version

Android/iOS uchun ST BLE Sensor ilovasi (2/5)

Hardware Features – Android Version

ESLATMA
The presence is identified inside a fixed range of distances that can be modified by the line code:

#define PRESENCE_MIN_DISTANCE_RANGE 300
#define PRESENCE_MAX_DISTANCE_RANGE 800

In file FLIGHT1_config.h.h, which can be found in the Inc users folder for each project.

Android/iOS uchun ST BLE Sensor ilovasi (3/5)

Board Configuration – Android version

Android/iOS uchun ST BLE Sensor ilovasi (4/5)

Debug Console – Android version

Android/iOS uchun ST BLE Sensor ilovasi (4/5)

Firmware Upgrade – Android version

Android/iOS uchun ST BLE Sensor ilovasi (5/5)

Hujjatlar va tegishli manbalar

FP-SNS-FLIGHT1:

DB2862: STM32Cube function pack for IoT node with NFC, BLE connectivity, and time-of-flight sensors – data brief

UM2026: Getting started with the STM32Cube function pack for IoT node with NFC, BLE connectivity, and time-of-flight sensors – user manual
Dasturiy ta'minotni sozlash file

X-NUCLEO-BNRG2A1

Gerber files, BOM, Schematic
DB4086: Bluetooth Low Energy expansion board based on the BLUENRG-M2SP module for STM32 Nucleo – data brief
UM2667: Getting started with the X-NUCLEO-BNRG2A1 BLE expansion board based on BLUENRG-M2SP module for STM32 Nucleo – user manual

X- NUCLEO-53L3A2:

Gerber files, BOM, Schematic
DB4226: Time-of-Flight ranging sensor with multi-target detection expansion board based on VL53L3CX for STM32 Nucleo – data brief
UM2757: Getting started with X-NUCLEO-53L3A2 multi target ranging ToF sensor expansion board based on VL53L3CX for STM32 Nucleo – user manual

VL53L3CX-SATEL:

Gerber files, BOM, Schematic
DB4194: VL53L3CX breakout board Time-of-Flight ranging sensor with multi-target detection – data brief

UM2853: How to use the VL53L3CX with STMicroelectronics’ X-CUBE-TOF1 Time-of-Flight sensor software packages for STM32CubeMX – user manual

Maslahatlash www.st.com to'liq ro'yxat uchun

STM32 ochiq rivojlanish muhiti: tugadiview

STM32 Open Development Environment: Fast, affordable Prototyping and Development

The STM32 Open Development Environment (STM32 ODE) is an open, flexible, easy, and affordable way to develop innovative devices and applications based on the STM32 32-bit microcontroller family combined with other state-of-the-art ST components connected via expansion boards. It enables fast prototyping with leading-edge components that can quickly be transformed into final designs

Qo'shimcha ma'lumot uchun tashrif buyuring www.st.com/stm32od.e

rahmat

STMicroelectronics korporativ logotipi STMicroelectronics kompaniyalar guruhining ro‘yxatdan o‘tgan savdo belgisidir. Boshqa barcha nomlar tegishli egalarining mulki hisoblanadi.

Tez-tez so'raladigan savollar

Savol: VL53L3CX-SATEL platasini boshqa ishlab chiqish platalari bilan ishlata olamanmi?
A: The VL53L3CX-SATEL board is designed to be compatible with STM32 Nucleo development boards, ensuring optimal performance and functionality
Savol: VL53L3CX-SATEL platasida proshivkani qanday yangilashim mumkin?
A: Firmware updates can be performed using the FOTA feature. Refer to the latest information available at www.st.com fordetailed instructions on firmware updates.

Hujjatlar / manbalar

ST STM32Cube IoT tugunining BLE Function Pack [pdf] Foydalanuvchi uchun qoʻllanma
NUCLEO-F401RE, NUCLEO-L476RG, NUCLEO-U575ZI-Q, X-NUCLEO-BNRG2A1, XNUCLEO-53L3A2, VL53L3CX-SATEL, STM32Cube IoT tugun BLE Function to'plami, BLETM Function to'plami, STM, Funktsiyalar to'plami

Ma'lumotnomalar

Foydalanuvchi uchun qo'llanma

STM32Cube IoT tuguni BLE Function Pack

Texnik xususiyatlari

Mahsulotdan foydalanish bo'yicha ko'rsatmalar

Uskuna va dasturiy ta'minot tugadiview

Muhim apparat qo'shimcha ma'lumot

Asosiy xususiyatlar

Dasturiy ta'minot va boshqa shartlar

O'rnatish tugadiview

Flash boshqaruvi va yuklash jarayoni

Bluetooth kam energiya va sensorlar uchun dasturiy ta'minot

Hujjatlar va tegishli manbalar

Tez-tez so'raladigan savollar

Hujjatlar / manbalar

Ma'lumotnomalar

Fikr qoldiring

Javobni bekor qilish