STM32Cube IoT नोड BLE फ़ंक्शन पैक

विशेष विवरण

• उत्पाद का नाम: VL53L3CX-SATEL
• Function Pack: STM32Cube function pack for IoT node BLEconnectivity and time-of-flight sensors (FP-SNS-FLIGHT1)
• संस्करण: 4.1 (31 जनवरी, 2025)

हार्डवेयर खत्मview
The VL53L3CX-SATEL is a breakout board with the VL53L3CX time-of-flight sensor.

प्रमुख विशेषताऐं

• Arduino UNO R3 कनेक्टर
• ब्लूटूथ लो एनर्जी कनेक्टिविटी के लिए BLUENRG-M2SP
• मेमोरी स्टोरेज के लिए M95640-RMC6TG

सॉफ्टवेयर विवरण:
The firmware update (FOTA) feature allows for easy software updates.

सॉफ़्टवेयर आवश्यकताएं:
Compatible with STM32 Nucleo development boards, specificallyNUCLEO-F401RE, NUCLEO-L476RG, or NUCLEO-U575ZI-Q.

अतिरिक्त जानकारी:
For firmware updates, refer to the latest information available at www.st.com।

उत्पाद उपयोग निर्देश

सेटअप और डेमो पूर्वampलेस

चरण 1: हार्डवेयर सेटअप
Connect the VL53L3CX-SATEL breakout board to an STM32 Nucleo development board (NUCLEO-F401RE, NUCLEO-L476RG, or NUCLEO-U575ZI-Q) using the appropriate connectors.

चरण 2: सॉफ़्टवेयर सेटअप
Ensure that the necessary software prerequisites are installed on your system as specified in the documentation.

चरण 3: डेमो एक्सampलेस
दिए गए डेमो उदाहरण को देखेंamples to understand how to interact with the VL53L3CX sensor using the provided software architecture.

हार्डवेयर और सॉफ्टवेयर खत्मview

Sample implementations are available for STM32 Nucleo development boards plugged into STM32 Nucleo expansion boards:

• NUCLEO-F401RE (or NUCLEO-L476RG or NUCLEO-U575ZI-Q) + X-NUCLEO-BNRG2A1 + X-NUCLEO-53L3A2
• NUCLEO-F401RE (or NUCLEO-L476RG or NUCLEO-U575ZI-Q) + X-NUCLEO-BNRG2A1 + X-NUCLEO-53L3A2

ब्लूटूथ कम ऊर्जा विस्तार बोर्ड

हार्डवेयर विवरण

• The X-NUCLEO-BNRG2A1 is a Bluetooth Low Energy (BLE) evaluation and development board system, designed around ST’s BLUENRG-M2SP Bluetooth Low Energy module based on BlueNRG-2.
• The BlueNRG-2 processor hosted in the BLUENRG-M2SP module communicates with the STM32 microcontroller, hosted on the Nucleo development board, through an SPI link available on the Arduino UNO R3 connector.

बोर्ड पर प्रमुख उत्पाद

• BLUENRG-M2SP Bluetooth Low Energy, FCC and IC certified (FCC ID: S9NBNRGM2SP, IC: B976C-BNRGM2SP), module based on Bluetooth® Low Energy wireless network processor BlueNRG-2, BLE v5.0 compliant.
• BLUENRG-M2SP integrates a BALF-NRG-02D3 balun and a PCB antenna. It embeds a 32 MHz crystal oscillator for the BlueNRG-2.
• M95640-RMC6TG 64-Kbit serial SPI bus EEPROM with high-speed clock interface

X- NUCLEO-53L1A2 Hardware Description

• The X-NUCLEO-53L3A2 is a ranging sensor with multi-target detection evaluation and development board designed around the VL53L3CX sensor based on ST FlightSense Time-of-Flight technology.
• VL53L3CX Arduino UNO R32 कनेक्टर पर उपलब्ध I2C लिंक के माध्यम से STM3 न्यूक्लियो डेवलपर बोर्ड होस्ट माइक्रोकंट्रोलर के साथ संचार करता है।

बोर्ड पर प्रमुख उत्पाद

• VL53L3CX Time-of-Flight (ToF) ranging sensor with multi-target detection
• 0.25, 0.5, and 1mm spacers to simulate air gaps, with the cover glass
• Cover window (made by Hornix) sample with low cross-talk,k ready to use / clipable on VL53L3CX
• Two VL53L3CX breakout boards

VL53L3CX-SATEL हार्डवेयर विवरण

• The VL53L3CX-SATEL breakout boards can be used for easy integration into customer devices. Thanks to the voltagई रेगुलेटर और लेवल शिफ्टर्स के साथ, इसका उपयोग 2.8 V से 5 V आपूर्ति के साथ किसी भी अनुप्रयोग में किया जा सकता है।
• The PCB section supporting the VL53L3CX module is perforated so that developers can break off the mini-PCB for use in a 2.8 V supply application using flying leads.

बोर्ड पर प्रमुख उत्पाद

• VL53L3CX Time-of-Flight (ToF) ranging sensor with witmulti-targetet detection
• Regulator: 5 to 2.8 V range input voltagई (आउटपुट वॉल्यूमtagई: 2.8 वी)
• VL53L3CX signal interface level shifter

महत्वपूर्ण हार्डवेयर अतिरिक्त जानकारी

BlueNRG-2 library does not work with the stock firmware that is loaded in the BLE module of the X-NUCLEO-BNRG2A1 expansion board.
इस कारण से:

• First of all, it is needed to solder on X-NUCLEO-BNRG2A1; if it is not soldered, a 0-ohm resistor at R117.
• Then you can use a standard ST-Link V2-1 with 5 jumper wires female-female together with the TSW-BNRGFLASHER software tool (currently available only for Windows PC) to update the firmware of the BLE module of X-NUCLEO-BNRG2A1.

आपको X-NUCLEO-BNRG12A2 के J1 ​​पिन को ST-Link V2-1 के पिन से जोड़ना होगा जैसा कि चित्र में दिखाया गया है और अगली स्लाइड में दिखाए गए चरणों का पालन करना होगा।
In particular, we have the following connections:

	जे12	ST-Link V2-1
नत्थी करना	1	1
नत्थी करना	2	9
नत्थी करना	3	12
नत्थी करना	4	7
नत्थी करना	5	15

1. Install the ST BlueNRG-1_2 Flasher Utility and open it, then select the SWD tab.b
2. Erase the flash memory of the BlueNRG-2 chip.
3. Download the Link Layer Only firmware for the BLE module from the following link: DTM_LLOnly. binn
4. Load the Link Layer Only firmware in the ST BlueNRG-1_2 Flasher Utility and then press the “Flash” button.
5. If you need to restore the stock firmware of the BLE module of X-NUCLEO-BNRG2A1, you can repeat the procedure using this firmware image DTM_Full.bi.n
6. If you should find some issues during the update process, you can try to repeat the procedure closing the J15 jumper on the X-NUCLEO-BNRG2A1 expansion board.

	VL53L3CX-सैटेल	Arduino कनेक्टर	न्यूक्लियो-F401RE न्यूक्लियो-L476RG	न्यूक्लियो-U575ZI-Q
एससीएल	2	डी15	पीबी8	पीबी8
एसडीए	4	डी14	पीबी9	पीबी9
एक्सएसडीएन	3	D4	पीबी5	पीएफ14
वीडीडी_सेंसर	5	3वी3	CN6 पिन नं. 4	CN8 पिन नं. 7
जीएनडी_X	6	जीएनडी	CN6 पिन नं. 6	CN8 पिन नं. 11

सॉफ्टवेयर विवरण

• The FP-SNS-FLIGHT1 is an STM32Cube function pack, which lets your IoT node connect to a smartphone via BLE and uses a suitable Android or iOS application like the STBLESensor app to view टाइम-ऑफ-फ़्लाइट सेंसर द्वारा पढ़ा गया वास्तविक समय वस्तु दूरी डेटा।
• The package also enables advanced functions, such as presence detection within a fixed range.
• This package, together with the suggested combination of the STM32 and ST devices, can be used to develop wearable applications or smart thing applications in general.
• The software runs on the STM32 microcontroller and includes all the necessary drivers to recognize the devices on the STM32 Nucleo development board.

प्रमुख विशेषताऐं

• Complete firmware to develop an IoT node with BLE connectivity, and Time-of-Flight sensors
• Compatible with STBLESensor application for Android/iOS to perform distance data reading and firmware update (FOTA)
• Multitarget ranging sensor application based on the VL53L3CX Time-of-Flight (ToF) sensor
• Sample implementation available for X-NUCLEO-53L3A2 (or VL53L3CX-SATEL) and X-NUCLEO-BNRG2A1 connected to a NUCLEO-F401RE or NUCLEO-L476RG or NUCLEO-U575ZI-Q
• Compatible with STM32CubeMX, can be downloaded from and installed directly into STM32CubeMX
• विभिन्न MCU परिवारों में आसान पोर्टेबिलिटी, STM32Cube के लिए धन्यवाद
• मुफ़्त उपयोगकर्ता के अनुकूल लाइसेंस शर्तें

सेटअप और डेमो पूर्वampलेस

सॉफ़्टवेयर और अन्य पूर्वापेक्षाएँ

• एसटीएसडब्ल्यू-LINK004
  • STM32 ST-LINK Utility (STSW-LINK004) is a full-featured software interface for programming STM32 microcontrollers
• एफपी-एसएनएस-फ़्लाइट1
  • .ज़िप की प्रतिलिपि बनाएँ file content of the firmware package into a folder on your PC.
  • पैकेज में स्रोत कोड शामिल हैamples (Keil, IAR, STM32CubeIDE) compatible with NUCLEO-F401RE, NUCLEO-L476RG, NUCLEO-U575ZI.
• ST BLE Sensor
  Application for Android (V5.2.0 or higher) /iOS (V5.2.0 or higher) to download from Google Store / iTunes

सेटअप ओवरview: STM32 न्यूक्लियो विस्तार बोर्ड के साथ 

सेटअप ओवरview

STM32 न्यूक्लियो एक्सपेंशन बोर्ड के साथ हार्डवेयर पूर्वापेक्षाएँ 

• 1 x Bluetooth Low Energy expansion board (X-NUCLEO-BNRG2A1)
• 1 x STM32 ranging sensor expansion board (X-NUCLEO-53L3A2 or VL53L3CX-SATEL)
• 1 x STM32 Nucleo development board (NUCLEO-U575ZI-Q or NUCLEO-F401RE or NUCLEO-L476RG)
• 1x Android or iOS device
• 1 x PC with Windows 10 and above
• 1x USB type A to Mini-B USB cable for NUCLEO-F401RE or NUCLEO-L476RG
• 1x USB type A to Micro-B USB cable for NUCLEO-U575ZI-Q

बस कुछ ही मिनटों में कोडिंग शुरू करें (1/3)

बस कुछ ही मिनटों में कोडिंग शुरू करें (2/3)

1. How to install the pre-compiled binary:
   • For each application, there is inside the package one folder called “Binary”

इसमें है:

• NUCLEO-F401RE और NUCLEO-L476RG के लिए:
  • pre-compiled FP-SNS-FLIGHT1 FW that could be flashed to a supported STM32 Nucleo for X-NUCLEO-53L3A2 using the STM32CubeProgrammer at the right position (0x08004000)
  • Important Note: This pre-compiled binary is compatible with the FOTA update procedure
  • pre-compiled FP-SNS-FLIGHT1 + BootLoader FW that could be directly flashed to a supported STM32 Nucleo for X-NUCLEO-53L3A2 using the STM32CubeProgrammer or by doing “Drag & Drop”
  • Important Note: This pre-compiled binary is not compatible with the FOTA update procedure
  • pre-compiled FP-SNS-FLIGHT1 FW that could be directly flashed to a supported STM32 Nucleo for VL53L3CX-SATEL using the STM32CubeProgrammer or by doing “Drag & Drop”
• NUCLEO-U575ZI-Q के लिए:
  • pre-compiled FP-SNS-FLIGHT1 could be directly flashed to a supported STM32 Nucleo (for X-NUCLEO-53L3A2 and for VL53L3CX-SATEL) using the STM32CubeProgrammer or by doing “Drag & Drop”.
  • Important Note: For the first installation, after the full flash erase (suggested procedure), use the STM32CubeProgrammer to set the STM32 MCU user byte settings to use bank 1 for flashing the firmware and start the application

How to install the code after compiling the project for NUCLEO-F401RE and NUCLEO-L476RG:

• Compile the project with your preferred IDE

In the folder Utilities, there is a script *.sh that performs the following operations:

• Full Flash Erase
• Flash the right BootLoader at the right position (0x08000000)
• Flash the FLIGHT1 firmware at the right position (0x08004000)
  • This is the firmware that was compiled with the IDE
  • This firmware is compatible with the FOTA update procedure
• Save a complete Binary FW that includes both FLIGHT1 and the BootLoader
  • This binary can be directly flashed to a supported STM32 board using the ST-Link or by doing “Drag & Drop.”
  • Important Note:Thiss additional pre-compiled binary is not compatible with the FOTA update procedure

Before executing the *.sh script, it is necessary to edit it to set the installation path for STM32CubeProgrammer.
BootLoaderPath and BinaryPath as input are required when executing the .sh script.

फ़्लैश प्रबंधन और बूट प्रक्रिया

ब्लूटूथ कम ऊर्जा और सेंसर सॉफ्टवेयर

NUCLEO-F1RE / NUCLEO-L401RG / NUCLEO-U476ZI-Q के लिए FP-SNS-FLIGHT575 – सीरियल लाइन मॉनिटर (जैसे टेरा टर्म) 

डेमो एक्सampलेस एसटी BLE सेंसर आवेदन खत्मview

Android/iOS के लिए ST BLE सेंसर एप्लीकेशन (1/5)

Hardware Features – Android Version

Android/iOS के लिए ST BLE सेंसर एप्लीकेशन (2/5)

Hardware Features – Android Version

टिप्पणी
The presence is identified inside a fixed range of distances that can be modified by the line code:

• #define PRESENCE_MIN_DISTANCE_RANGE 300
• #define PRESENCE_MAX_DISTANCE_RANGE 800

में file FLIGHT1_config.h.h, which can be found in the Inc users folder for each project.

Android/iOS के लिए ST BLE सेंसर एप्लीकेशन (3/5)

Board Configuration – Android version

Android/iOS के लिए ST BLE सेंसर एप्लीकेशन (4/5)

Debug Console – Android version

Android/iOS के लिए ST BLE सेंसर एप्लीकेशन (4/5)

Firmware Upgrade – Android version

Android/iOS के लिए ST BLE सेंसर एप्लीकेशन (5/5)

दस्तावेज़ और संबंधित संसाधन

एफपी-एसएनएस-फ्लाइट1: 

• DB2862: STM32Cube function pack for IoT node with NFC, BLE connectivity, and time-of-flight sensors – data brief
• UM2026: Getting started with the STM32Cube function pack for IoT node with NFC, BLE connectivity, and time-of-flight sensors – user manual
• सॉफ्टवेयर सेटअप file

एक्स-न्यूक्लियो-बीएनआरजी2ए1

• गर्बर files, BOM, Schematic
• DB4086: Bluetooth Low Energy expansion board based on the BLUENRG-M2SP module for STM32 Nucleo – data brief
• UM2667: Getting started with the X-NUCLEO-BNRG2A1 BLE expansion board based on BLUENRG-M2SP module for STM32 Nucleo – user manual

X- NUCLEO-53L3A2:

• गर्बर files, BOM, Schematic
• DB4226: Time-of-Flight ranging sensor with multi-target detection expansion board based on VL53L3CX for STM32 Nucleo – data brief
• UM2757: Getting started with X-NUCLEO-53L3A2 multi target ranging ToF sensor expansion board based on VL53L3CX for STM32 Nucleo – user manual

वीएल53एल3सीएक्स-सैटेल:

• गर्बर files, BOM, Schematic
• DB4194: VL53L3CX breakout board Time-of-Flight ranging sensor with multi-target detection – data brief
• UM2853: How to use the VL53L3CX with STMicroelectronics’ X-CUBE-TOF1 Time-of-Flight sensor software packages for STM32CubeMX – user manual

परामर्श करें www.st.com पूरी सूची के लिए

STM32 ओपन डेवलपमेंट एनवायरनमेंट: ओवरview

STM32 Open Development Environment: Fast, affordable Prototyping and Development

The STM32 Open Development Environment (STM32 ODE) is an open, flexible, easy, and affordable way to develop innovative devices and applications based on the STM32 32-bit microcontroller family combined with other state-of-the-art ST components connected via expansion boards. It enables fast prototyping with leading-edge components that can quickly be transformed into final designs

अधिक जानकारी के लिए कृपया यहां जाएं www.st.com/stm32od.e

धन्यवाद

© एसटीएमइक्रोइलेक्ट्रॉनिक्स - सभी अधिकार सुरक्षित।

एसटीमाइक्रोइलेक्ट्रॉनिक्स का कॉर्पोरेट लोगो, एसटीमाइक्रोइलेक्ट्रॉनिक्स समूह की कंपनियों का एक पंजीकृत ट्रेडमार्क है। अन्य सभी नाम उनके संबंधित स्वामियों की संपत्ति हैं।

अक्सर पूछे जाने वाले प्रश्नों

• प्रश्न: क्या मैं VL53L3CX-SATEL बोर्ड का उपयोग अन्य विकास बोर्डों के साथ कर सकता हूँ?
  A: The VL53L3CX-SATEL board is designed to be compatible with STM32 Nucleo development boards, ensuring optimal performance and functionality
• प्रश्न: मैं VL53L3CX-SATEL बोर्ड पर फर्मवेयर कैसे अपडेट कर सकता हूं?
  A: Firmware updates can be performed using the FOTA feature. Refer to the latest information available at www.st.com fordetailed instructions on firmware updates.

दस्तावेज़ / संसाधन

ST STM32Cube IoT नोड BLE फ़ंक्शन पैक [पीडीएफ] उपयोगकर्ता गाइड NUCLEO-F401RE, NUCLEO-L476RG, NUCLEO-U575ZI-Q, X-NUCLEO-BNRG2A1, XNUCLEO-53L3A2, VL53L3CX-SATEL, STM32Cube IoT नोड BLE फ़ंक्शन पैक, STM32Cube, IoT नोड BLE फ़ंक्शन पैक, BLE फ़ंक्शन पैक

संदर्भ

• उपयोगकर्ता पुस्तिका