Bluedio UFO PLUS User Manual

Bluedio UFO PLUS

USER MANUAL

Bluedio UFO PLUS

Bluedio Headphone
Model: UFO PLUS

Welcome to use this manual
Thanks very much for your great support to this headset.

To verify the headset
Scrape the anti-fake label on the package for verification code; Visit our website: www.bluedio.com; Enter the verification code to verify the headset

For information and help
Welcome to visit our website: www.bluediocom; Or to email as at [email protected]; Or to call us at 020-86062626-835.

Read this user manual carefully and completely before using the headset.

  • DON’T use the headphones at a high volume for any extended period to prevent hearing damage.
  • DON’T use the headphones while driving or in any environment requiring your full attention.
  • Keep the headphones, accessories and packaging parts out of reach of children to prevent accidents and choking hazards.
  • Always keep the headphones dry and DON’T use the headphones near water.
  • STOP using the headphones immediately if you feel sick while using the headphones.
  • DON’T expose the headphones to either extremely high or low temperatures(ideal: 10°C to 35°C ).
  • Removal of the chargeable battery in the headphones shall be conducted only by a qualified professional. DON’T try to replace the battery on your own.
  • If the headphones have incompatible issues with your laptop or desktop, please use the included audio cable to connect; or buy a CSR4.0 and above Bluetooth adapter.

In the Box

In the Box

Headset Overview

Headset Overview

MF button:

  • When the headset is off, press and hold the MF button until you hear “Power On, Pairing”, the headset is on and in pairing mode, and the blue light will stay on.
  • When the headphones are on, press and hold the MF button until you hear “Power off’.
  • When playing music, press the MF button once to Pause/Play.
  • When receiving a call, press the MF button once to answer/end; press and hold for 2s to reject.
  • Receiving call 2 when In call 1, press and hold the MF button to keep call 1 and answer call 2; press and hold the MF button to switch back to call 1; press once to end.
  • Press the MF button twice to redial the last number.
MF button

Volume+ button:
Press Volume+ button once to turn up the volume.

Volume+ button

Volume- button:
Press Volume- button once to turn down the volume.

Volume- button

Previous track/EQ conversion:
Press once to skip back to the previous track; press and hold to turn off the EQ effect.

Previous track

Next track/EQ conversion:
Press once to skip forward to the nerd track; press and hold to turn on the EQ effect.

Next track

Bluetooth pairing:

Turn on the headset; twill enter pairing mode automatically; turn on the Bluetooth feature on your phone; select “UPlus”; once successfully paired, you will hear ‘Connected”.

Note: If the pairing is not successful within 3 minutes, please repeat above steps to try pairing again. If the headset has successfully connected to your phone, simply turn on the headset and Bluetooth feature of your phone to reestablish the Bluetooth connection.

Connecting to 2 mobile phones:

  1. Connect UPlus with phone 1, then turn off UPlus and The Bluetooth feature of phone 1.
  2. Turn on UPlus and make it enter pairing mode.
  3. Connect UPlus with phone 2.
  4. Turn on the Bluetooth feature of phone 1; select “UPlus” to conned.
Connecting to 2 mobile phones

Line-in music playback:
Connect the headset to your mobile phone or computer via the standard 3.5mm audio cable.
Note: Turn off the headset before using this feature.

Clear the pairing memory:
Make the headset enter pairing mode, then press the Volume+ and Volume- buttons together.

Clear the pairing memory

Specifications:

  • Bluetooth version: V4.1
  • Bluetooth operating range: up to 10m (free space)
  • Bluetooth transmission frequency: 2.4GHz-2.48GHz
  • Bluetooth profiles: A2DP, AVRCP, HSP, HFP
  • Drivers: 50mm x 2; (3Ornm x 2; (2Omm x 8)
  • Impedance: 420 ( 50mm), 320 ( 30mm), 320 ( 20mm)
  • Frequency response: 10Hz-22KHz
  • Sound pressure level(SPL) : 112dB
  • Bluetooth music/talk time: about 25 hours
  • Standby time: about 1000 hours
  • Fully charged time: about 2.5 hours
  • Charging voltage: 5V
  • current: 9500mA
  • Power Consumption: 109mw

Questions about your Manual? Post in the comments!

Haylou GT1 TWS Bluetooth Earbuds User Manual

Haylou-GT1

User Manuals

TWS BT Earphones
Haylou-GT1

Overview

Charging Case

Charging Case

What’s in the Box
BT earphones, Charging case, EarTips × 2 pairs, Manual, Charging cable.

Earphones

Earphones

Medium Ea r T i p s h ave been assembled in advance.
However, you may try large or small ones, if the medium ones do not fit you well.

Please keep Mic outside when calling

When calling, adjust Mic towards mouth to gain clear calling.

Power-on

Take out earphones from the case to power on them. Or touch both panels for 1.5s to power on earphones (LED glows solid white) when they are not in the case.

Power-off
Put earphones into the case to power off them.
Or touch both panels for 4.5s to power off earphones.
(LED glows solid red for 2s).

Power-off

Ignore Call
Touch the panel for 1s to ignore incoming call.

Ignore Call

Stereo Mode

Auto pairing: take out both EarBuds from the case and they will auto pair with each other in 2 or 3s. Earphones will be connectable to cellphone when white slowly. On cellphone, LED on right EarBud blinks search for “Haylou-GT1_R” and tap to connect.
If earphones fail to be connected to cellphone, please put EarBuds back to the case and repeat the above steps. Earphones will auto reconnect to the last device in connectivity records, if any.

Note: earphones have been setted to factory when shipping out.

Stereo Mode

Manual pairing: manually power on two EarBuds and they will auto pair with each other when LED blinks white promptly. Then LED on the right EarBud will blink white slowly and now you can tap it on cellphone to connect.

Mono Mode

Auto pairing: take out one EarBud from the case to power on it. Its LED will soon blink slowly then search for Haylou-GT1 R/L on cellphone and tap to connect. EarBud will auto reconnect to last device in connectivity records, if any.

Note: it may take more times for the left EarBud to reconnect.

Manual pairing: manually power on one EarBud. Its LED will soon blink white slowly then search for it on cellphone and tap to connect.

How to Charge

Prior to using, please peel off sticker on the pogo pins and top up the earphones.

How to Charge

Play/pause

When standby, touch the panel to pause/play music.
Note: media player should run in background.

Play/pause

Voice Assistant
When standby, triple touch the panel to activate voice assistant.
Note: device needs to support voice assistant and fast awakening be turned on.

Voice Assistant

Answer/End Call
Double touch the panel to answer incoming call and double touch the panel again to end it.

Answer/End Call

Skip Track Forward/backward

Touch the panel on right earbud twice to skip track forward.
Touch the panel on left earbud twice to skip track backward.

Three-way Calling & Switch

Touch the panel twice to answer incoming call from phone. if another call is coming in sync , touch the panel to put the first call on hold while activating the second one. Double touch the panel to switch between active call and held call.

Switch Audio Output
When calling, touch the panel for 1s to switch audio output between earphones and cellphone.

Factory Setting
If earphones do not function well, please refer the following steps to reset factory: take EarBuds out from the case. Power off the earphones then touch both panels for about 15s ( LED will blink red and white three times twice). After that, put them back to the case. Delete connectivity record on cellphone before processing another pairing. (All connectivity records relating to the EarBuds will all be removed )

Basic Parameters
Operation range: 10m(with no obstacle)
Battery capacity: 43mAh(single EarBud)
Changing time: approx. 1.5hr
Calling time: approx. 3.5hr
Standby time: approx. 150hr
Input parameter: 5V 100mA
Battery type: li-ion
Wireless connection: BT 5.0

Charging Case
Input parameter:5V 500mA
Output parameter:5V 150mA
Charging time: approx. 2hr
Standby time: approx. 4 months
Battery capacity: 310mAh
Battery type: li-ion

Caveats

  1. Never disassemble or modify your headset for any reasons to avoid any damages and danger.
  2. Do not store the headset in extreme temperatures (under 0℃ or over 45℃).
  3. Avoid using the indicator close to the eyes of children or animals.
  4. Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electricshock.
  5. Do not use harsh chemicals or strong detergents to clean the headset.
  6. Keep the headset dry.

Warranty Card

Warranty Period
12 months after the next day receiving this item. Free exchange service will not be accessed under following circumstances:

  1. Damages caused unauthorized disassembly.
  2. Defects or physical damages caused by leaking or dropping off.
  3. Damages by act of God.Supposing your item is within any damages or defects except the above circumstances, please return to us or your distributor for free repairing.

Tips

  1. Before using the headset, please read the manual carefully and keep it for future references.
  2. The headset need to be fully charged prior to first-time use.
  3. If the headset is left unused for over two weeks, please recharge it periodically.
  4. Please use the chargers made by qualified manufacturer.
  5. If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please re-enter the mode; if a procedure error of your phone occurs, reboot it; if a procedure error of the headsetoccurs, reboot or reset it.

Address: Suite 1303, 1305 and 1306, 13/F, Project Phrase
2 of Gaosheng Tech Tower, Gaosheng Tech Park,
No.5 Longxi Road, Zhouxi Community, Nancheng
District, Dongguan City, Guangdong, China.
Manufacturer: Dongguan Liesheng Electronic
Co., Ltd.
Web: www.haylou.com
Perform standard: Q/LS 1-2018

Made In China

Hazardous substances and their contents in the item

Hazardous Substances

Notes : Please arrange using time properly as your hearing may be damaged by using the device for a long time.

EU Declaration of Conformity Hereby, Liesheng Inc., declares that the radio equipment type LYEJ05LM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

In addition, for a portable sound system, the instructions shall include a warning that excessive sound pressure from earphones and headphones can cause hearing loss.

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
To prevent possible hearing damage, do not listen at high volume levels for long periods.

WEEE

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

FCC Warning

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

If you have any Question About your User Manual, Post on the Comment.

User Manual JBL Live 400 BT / Live 500 BT Headphones

LIVE400BT / LIVE500BT

INSTRUCTION MANUAL

LIVE400BT
LIVE500BT

LIVE400BT / LIVE500BT
Quick Start Guide

1. What’s in the box

LIVE400BT / LIVE500BT

In the box

Charging cable

Charging cable

Detachable audio cable with remote

Detachable audio cable with remote

Warranty card, Warning card, Safety sheet, QSR, QSG

Warranty card, Warning card, Safety sheet, QSR, QSG

2. Overview

a. Buttons & LEDs

Buttons & LEDs

b. Connections

Connections

3. Bluetooth® Pairing

Bluetooth Pairing
  1. Turn on the headphone
  2. If connecting for the first time, the headphone will enter the pairing mode automatically after it is powered on
  3. Connect to bluetooth device
Connect to bluetooth device

4. Controlling music

Controlling music
Controlling music

5. Managing phone calls

Managing phone calls
Managing phone calls

6. Voice Assistant

Voice Assistant

7. Download My JBL Headphones APP

Download My JBL Headphones APP

Get even more control and personalization of your listening experience with this free App.

8. The Google Assistant

a. To set up the Google Assistant

  1. Connect your headphones to your mobile device
  2. Set up your Google Assistant using your mobile device:
    a. On your Android device, press and hold the home button to open the Google Assistant and follow the on-screen instructions.
    b. On your iOS devices, open or download the Google Assistant app and follow the app instructions.
Google Assistant

Note: The Google Assistant is available on eligible Android 6.0 devices* or later.
For iOS devices, the Google Assistant app needs to be downloaded. Works on Lollipop,
Marshmallow and Nougat Android Phones with Google Play Services, >1.5GB of memory and 720p or higher screen resolution.
For more information on what your Google Assistant can do, visit:
assistant.google.com/platforms/headphones

b. To use your Google Assistant

To use your Google Assistant
Function

Note:

  1. The Google Assistant isn’t available in certain languages and countries.
  2. If you want to turn on or off the Google Assistant, please download our JBL APP (see Section 7). You can select under Settings > Voice assistant > Google Assistant.
    For countries without the Google Assistant, you can double tap the left ear cup to activate voice assistant.

9. Amazon Alexa

  1. Connect your headphones to your mobile device.
  2. Download JBL APP and follow the app instructions, select Settings > Voice assistant > Amazon Alexa
Amazon Alexa

3. On your mobile device, open or download the Amazon Alexa app and follow the app
instructions.

4. In the Amazon Alexa App, navigate to the Device Page.

5. Click the Plus (+) button on the top right of the screen and select ‘Add Device’.

6. Select Headphones from the list and then choose your Live Series Headphones in the Available Devices section. Follow the rest of the instructions in the Alexa App to complete set up.

7. Alexa is now enabled on your device. Touch the action button and try one of the below utterances:

Alexa is now enabled
Things to try Example

Note:

  1. For more information and things to try with Alexa, visit: www.amazon.com/alexadevices and select ‘Use Alexa’.
  2. If you want to turn on or off the Amazon Alexa, please download our JBL APP
    (see Section 7). You can select under Settings > Voice assistant > Amazon Alexa.
  3. Alexa is not available in all languages and countries.

10. Factory reset

Factory reset

11. Ambient Aware & TalkThru

  1. Short press once to activate TalkThru, which allows you to clearly hear others for quick conversations, without removing your headphones. You will hear your music volume level lower when TalkThru Technology is engaged.
  2. Press once more to activate Ambient Aware, which allows you to hear your surroundings.
  3. Press again to turn off TalkThru Technology.
    Note: You can also turn on or off the Ambient Aware & TalkThru with our JBL APP (see Section 7).
TalkThru with our JBL APP

12. Wired listening mode

Wired listening mode

13. Seamlessly switch between devices

Seamlessly switch between devices
  1. Pair and connect the headphone with the 1st Bluetooth device (see Section 3 Bluetooth pairing)
  2. Pair and connect the headphone with the 2nd Bluetooth device
  3. Connect to bluetooth device
Connect to bluetooth device

4. Go back to the Bluetooth device list on the 1st device and select the headphone* to connect

Go back to the bluetooth device list

Items to note:
a. Maximum 2 devices can be connected simultaneously

Items to note

b. To switch music source, pause the music on the current device and select play on the 2nd device.
c. Phone call will always take priority.
d. If one device goes out of Bluetooth range or powers off, you may need to manually
reconnect the remaining device. See Section 13 Step 3.

14. LED behaviour

LED behaviour
LED Status

Specifications:

JBL LIVE400BT
• Driver size: 40mm
• Dynamic frequency response range: 20Hz-20kHz
• Sensitivity: 106dB [email protected]/1mW
• Max input power: 15mW
• Transmit sensitivity: [email protected]/Pa
• Impedance: 32ohm
• Bluetooth transmitted power: 0-4dbm
• Bluetooth transmitted modulation: GFSK, π/4DQPSK, 8DPSK
• Bluetooth frequency: 2.402GHz-2.48GHz
• Profile version: A2DP V1.3, AVRCP V1.5, HFP V1.6
• Bluetooth version: V4.2
• Battery type: Polymer Li-ion Battery (3.7V DC, 700mAh)
• Charging time: 2 hours
• Music play time with BT on: Up to 24 hours
• Weight: 185.8g

JBL LIVE500BT
• Driver size: 50mm
• Dynamic frequency response range: 18Hz-20kHz
• Sensitivity: 108dB [email protected]/1mW
• Max input power: 15mW
• Transmit sensitivity: [email protected]/Pa
• Impedance: 32ohm
• Bluetooth transmitted power: 0-4dbm
• Bluetooth transmitted modulation: GFSK, π/4DQPSK, 8DPSK
• Bluetooth frequency: 2.402GHz-2.48GHz
• Profile version: A2DP V1.3, AVRCP V1.5, HFP V1.6
• Bluetooth version: V4.2
• Battery type: Polymer Li-ion Battery (3.7V DC, 700mAh)
• Charging time: 2 hours
• Music play time with BT on: Up to 30 hours
• Weight: 231.6g

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.
Google, Android, Google Play, the Google Play logo and related marks and logos are trademarks of Google LLC. The Google Assistant is not available in certain countries and languages. Availability and performance of certain features, services and applications are device and network dependent and may not be available in all areas. Controlling certain devices in your home requires compatible smart devices. Subscriptions for services and applications may be required and additional terms, conditions and/or charges may apply.

Questions about your Manual ? Post in the comments!

Soundpeats TrueCapsule User Manual

Soundpeats TrueCapsule

USER MANUAL

Soundpeats TrueCapsule

Soundpeats TrueCapsule

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Package Content
Package Content

Specifications

Specifications

Product Diagram

Product Diagram
Product Diagram

Controls

Controls

Wearing the earphones

  1. Identify the le and right earbuds.
  2. Rotate the earbuds, and adjust to nd the best angle.
  3. Make sure the ear tip seals in the ear canal.
Wearing the earphones

Getting Started
Pairing and Re-Pairing

  1. Pick up the le and right earbuds at the same time from the charging case when the charging case is powered, both earbuds will enter TWS Pairing mode automatically. You will hear a voice prompt when the le and right earbuds connect to each other successfully. Then the indicator of le earbud is going o, and the right indicator starts alternately ashes in red and white with a voice prompt “pairing” indicating pairing mode.
  2. “SOUNDPEATS TrueCapsule” will show up on the Bluetooth list, click it to connect. You will hear a voice prompt “connected” from right earbud when the earbuds connect with your device successfully
  3. SOUNDPEATS TrueCapsule Bluetooth earbuds can remember previously paired devices. When you make the second connection, simply activate the Bluetooth in your device, take out the both earbuds from the charging case. They will connect to each other, and reconnect to your device automatically. If the earbud doesn’t automatically connect to your device, please activate the Bluetooth in your device and hit “SOUNDPEATS TrueCapsule” on the Bluetooth list.
Bluetooth in your device

Note:

  1. If the left earbud is taking out from the charging case first and didn’t pair with the right earbud within 10 seconds, the left ear will enter the standby mode. Please place the earbuds back into the charging case and taking them out again after 3s, the earbuds will enter the pairing mode again. Otherwise, the le earbud will stay in standby mode for 3 minutes and then turn off.
  2. If you want to change the pairing device in the connected state, please turn off both earbuds, then press and hold the multifunction button of the right earbud for 6s to have it enter pairing mode directly and pair to a new device.

Factory Reset
(Try the following steps if you fail building connection between two earbuds, or between earphones and device)

  1. Clear pairing record between the earbuds and all your devices.
  2. Place back both earbuds into the charging case and ensure they’re in charging status. Then long press the multifunction button of both earbuds for 10s until the LED light of both earbuds ash white twice.

Charging
SOUNDPEATS TrueCapsule Bluetooth earphones are equipped with a lightweight charging case which is not only a charging dock to charge the earphones, but also a carrying case. With a built-in rechargeable battery, the charging case can provide up to 5-6 times full charge for the earphones (both le and right).

Charging the headset
The earphones are partially charged at the factory. Please make sure they are fully charged before rst use.

  1. Put the earphones into corresponding charging docks, make sure the charging contractors are match.
  2. The LED indicator will turn red when it starts charging.
  3. The red LED indicator will turn o when the earphones are fully charged.

Charging the case
When charging case battery is low, the last indicator of the charging case will ash white. Please charge the case soon.

  1. Connect the charging port with USB charging adapter. (Please make sure the current is not greater than 1A)
  2. Please charge the case at least once every 3 months when not in use for a long time.
Charging the case

Warranty
We warrant this device 12 MONTHS from date of the original purchase for Manufacturer defects.
[email protected]
www.soundpeatsaudio.com
Please scan the QR code to check the detailed PDF manual
https://soundpeatsaudio.com/downloads/

QR code

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must
accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Soundpeats TrueWings User Manual

Soundpeats TrueWings

USER MANUAL

Soundpeats TrueWings

Soundpeats TrueWings

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Package Content

Package Content
Package Content
Specifications

Product Diagram

Product Diagram
Product Diagram

Button Control

Button Control

Wearing

  1. Identify the le and right earbuds.
  2. Rotate the earbuds to make sure the ear hooks lock over your ears firmly.
  3. Make sure the ear tips seal your ear cancals.
Wearing

Get Started
Pairing

  1. Take both earbuds out from the charging case, the le and right earbuds will pair to each other at rst with a prompt suggests successfully. Aer this, the le indicator will turn white, and right indicator ashes in red and white alternately with a voice prompt “Pairing” indicating the earbuds enter pairing mode.
  2. Activate the Bluetooth on your device and choose “SOUNDPEATS TrueWings” to connect. The right indicator will stop ashing with a voice prompt “Connected”.
  3. SOUNDPEATS TrueWings earbuds can remember previously paired device. To reconnect to one device, you only need to activate the Bluetooth in the device and take out both earbuds, the earbuds will automatically connect to each other, and then pair to the device. If they don’t re-pair automatically, please choose the pairing name to connect again.

Note:

  1. If the earbud doesn’t pair to each other within 5s, it would enter pairing mode and search for Bluetooth device. Both earbuds support working alone.
  2. If you want to change the pairing device in connected status, please have the earbuds enter pairing mode by pressing and holding the right earbud for 6s with earbuds off.

Transparency Mode
Transparency mode lets outside sound in and allows things to sound and feel natural when you are talking to people nearby. Double tap the le MFB to activate and deactivate transparency mode. The mode is not applicable during calls.

Factory Reset
(Try the following steps if you fail building connection between two earbuds, or between earbuds and device.)

  1. Clear the pairing record between the earbuds and all your devices.
  2. Manually power o both earbuds, then press and hold both MFBs for 10 seconds until both indicators ash in white twice

Charge
SOUNDPEATS TrueWings earbuds come with a charging case for easy carrying and charging. It can recharge both earbuds for around 4 times.

Charge the earbuds

  1. Place back the earbuds in the right charging slot and make sure the contactors connect.
  2. Charging starts with red indicators turning on.
  3. After fully charged, white indicators stay on for a minute before going out.

Charge the case
When the charging case is with low power le, the last white indicator on the case would ash, please recharge the charging case.

  1. Please charge the earbuds and case at least once every 3 months when not in use for a long time.
  2. To ensure charging safety, please do not use any USB charging adapter with current over 5V 1A. Please do not use quick charger to charge the earbuds and charging case.
Charge the case

Warranty
We warrant this product to be free from manufacturing defect for 12 MONTHS.
[email protected]
www.soundpeatsaudio.com
Please scan the QR code to view the detailed PDF format manual.
https://soundpeatsaudio.com/downloads/

 QR code

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B English digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Soundpeats Truengine2 User Manual

Soundpeats Truengine2

USER MANUAL

Soundpeats Truengine2

Soundpeats Truengine2

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Package Content

Package Content
Package Content

Specifications

Specifications
Product Diagram
Product Diagram

Touch Control

Touch Control
Touch Control

Wearing the earbuds

  1. Identify the left and right earbuds.
  2. Rotate the earbuds, and adjust to nd the best angle.
  3. Make sure the ear fins t your cymba conchae.
  4. Make sure the ear tip seals in the ear canal.
Wearing the earbuds

Getting Started
Pairing&Re-pairing

  1. Take out both earbuds from the charging case and ensure the charging case has enough battery, the earbuds will enter TWS Pairing mode automatically. You will hear a voice prompt when the lef and right earbuds connect to each other successfully. Then the indicator of le earbud goes out, and the right indicator alternately ashes in red and white with a voice prompt “pairing” indicating pairing mode.
  2. “SOUNDPEATS Truengine2” will show up on the Bluetooth list, click it to connect. You will hear a voice prompt “connected” from right earbud when the earbuds connect with your device successfully. Then, your device will remind again that “SOUNDPEATS Truengine2 L” request pairing, please click on it to connect.
Bluetooth Pairing

3. SOUNDPEATS Truengine2 Bluetooth earbuds can remember previously paired devices. When you make the second connection, simply activate the Bluetooth in your device, take out both earbuds from the charging case. They will connect to each other, and reconnect to your device automatically. If the earbud doesn’t automatically connect to your device, please activate the Bluetooth in your device and hit “SOUNDPEATS Truengine2” on the Bluetooth list.

4. Mono mode: aer SOUNDPEATS Truengine2 is paired successfully, both the le earbud and the right earbud can be used separately

Note:

  1. When SOUNDPEATS Truengine2 L requires pairing, please choose connection, or the Mono Mode can’t be used normally.
  2. When SOUNDPEATS Truengine2 connects with devices which have more advanced chips than Qualcomm Snapdragon 855 and Qualcomm, it will connect two pairing names automatically, no need to proceed second pairing manually.
  3. If you want to change the pairing device in the connected status, please just long press and hold the touch area for 6s to have it enter pairing mode directly and pair to a new device.

Factory Reset
(Try the following steps if you fail to build connection between two earbuds, or between earbuds and device)

  1. Clear pairing record between the earbuds and all your devices.
  2. Place back both earbuds into the charging case and ensure they’re in charging status. Then long press the touch area of both earbuds for 10s until the LED light of both earbuds flash white twice. Reset is complete.

Charging
SOUNDPEATS Truengine2 Bluetooth earbuds are equipped with a lightweight charging case which is not only a charging dock to charge the earbuds, but also a carrying case. With a built-in rechargeable battery, the charging case can provide 3.5 times full charge for the earbuds (both lef and right)

Charging the earbuds
The earbuds are partially charged at the factory. Please make sure they are fully charged before first use.

  1. Put the earbuds into corresponding charging docks, make sure the charging contractors are match.
  2. The LED indicator will turn red when it starts charging.
  3. The red LED indicator will turn o when the earbuds are fully charged.

Charging the case
When the charging case is in low battery level, only one white led indicator flashes,please recharge the case:

  1. Connect the charging port with Type-C charging adapter or computer Type-C port.(current less than 5V 1A)
  2. Please charge the earbuds at least once every 3 months when not in use for a long time.
Charging the case

Warranty
We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects.
[email protected]
www.soundpeatsaudio.com
Please scan QR code to know the PDF user manual.

https://soundpeatsaudio.com/downloads/

 QR code

Questions about your Manual ? Post in the comments!

Soundpeats TrueAir User Manual

Soundpeats TrueAir

USER MANUAL

Soundpeats TrueAir

Soundpeats TrueAir

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Package Content

Package Content
Package Content

Specifications

Specifications

Product Diagram

Product Diagram
Product Diagram
Product Diagram

Button Controls

Button Controls

Wearing the earphones

  1. Identify the le and right earbud.
  2. Rotate the earbuds and adjust them to the most comfortable positions.
Wearing the earphones

Getting Started
Pairing

  1. Open the charging case when it’s powered, please make sure the earbuds are inside the charging case, then the le and right earbud will enter into TWS mode automatically. Aer successful interconnection, you will hear a voice prompt from the le and right earbud. At this point, you need to long press the charging case button for 3S, the charging case indicator starts to ash white, then you will hear a “pairing” voice prompt, the earbuds get into pairing mode.
  2. Please search ”SOUNPEATS TrueAir” from your bluetooth list of your device, click connect, you will hear a “connected” voice prompt from right earbud if it’s successful. Then a pop up window “SOUNDPEATS TrueAir L” will appear on your phone, please click it to pair.
Paring

3. SOUNDPEATS TrueAir can remember the previously paired devices, when you make a secondary connection, you only need to open the Bluetooth of your device, take out both earbuds from the charging case, then they will pair with your device automatically. If not, please choose “SOUNDPEATS TrueAir” from your Bluetooth list to connect.

4. Mono mode: When the SOUNDPEATS TrueAir paired successfully, the left and right earbud can be used separately

Notes

  1. When “SOUNDPEATS TrueAir L” request for pairing, please select pairing,or the mono mode will not work properly.
  2. SOUNDPEATS TrueAir will automatically connect two pairing names when connected to a phone with Qualcomm Snapdragon 855 chip and Qualcomm higher level chip, no need to manually perform secondary pairing.
  3. If you want to change the paired device in the connected state, you can force the earbuds to enter the pairing mode, which means, you need to put the earbuds into the charging case and open the cover, then long press the charging case button for 3S.

Reset
When the secondary pairing of the earbuds is not successful or cannot be paired with the device, reset it as follows:

  1. Remove the pairing record of the earbuds from your device.
  2. Put the earbuds into the charging case and keep the cover open, then long press the charging case button for 10S.

Charging
SOUNDPEATS TrueAir is equipped with a charging case, not only charge for the earbuds, but also a box which is easy to carry and store. Built-in rechargeable battery, you can charge both earbuds 5 times.

Charging for the earbuds
The earbuds have been partially charged at the factory. Please make sure they are fully charged before first use

  1. Put the earbuds into the corresponding slots.
  2. If the indicator of the charging case ashes, it means the earbuds have beensuccessfully placed.
  3. Close the cover, then the earbuds start charging.

Charging for the case
When the charging case is low battery, the indicator turns red,then please charge for the case

  1. Connect Type-C to charge for the case(charge current less than 1A).
  2. Charge at least once every three months when not in use for a long time.
Charging for the case

Warranty Regulations
When the original buyer purchased this earbuds from us, the warranty starts, the period is 12 months, the warranty coverage is limited to manufacturing defects.
[email protected]
www.soundpeatsaudio.com
Please scan the QR code to view the detailed PDF format manual.
https://soundpeatsaudio.com/downloads/

 QR code

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B English digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Soundpeats Truengine SE User Manual

Soundpeats Truengine SE

USER MANUAL

Soundpeats Truengine SE

Soundpeats Truengine SE

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Package Content

Package Content
Package Content

Specifications

Specifications

Product Diagram

Product Diagram
Product Diagram

Button Controls
Once connected, The Truengine SE headphones can control media and phone calls from a phone or tablet.

Button Controls
Button Controls

Wearing The Earphones

  1. Identify left and right earbud.
  2. Adjust earbuds to find the most comfortable place.
  3. Insert earbuds to ensure seal well your ear channel.
Wearing The Earphones

Getting Started

Pairing & Repairing

  1. Left and right earbud will pair with each other when take out both earbuds simultaneously from charging case with power. Next the led Indicator of left earbud will goes out and led indicator on right earbud will flash red and white alternately and you can hear voice prompt “pairing”, which indicates that earbuds succeed In entering pairing mode.
  2. Please find the name of “SOUNDPEATS Truengine SE° on the Bluetooth list of your phone, click to connect, you can hear voice prompt °connected° from right earbud. Then you will get a pairing request again, please continue to click”SOUNDPEATS Truenglne SE L° to connect.
Paring

3. SOUNDPEATS Truengine SE Headphones can remember devices previously paired . If you have paired earbuds with a device once, simply activate the Bluetooth on your device, take out earbuds from charging case and close the lid, they will automatically reconnect with that device. If earbuds don’t automatically connect, select the earbuds name on your Bluetooth device to connect.

4. Play In mono mode: Len and right earbud can be used separately when SOUNDPEATS Truengine SE have paired successfully.

Note:

  1. When SOUNDPEATS Truengine SE L Headphones request pairing, please select pairing, otherwise earbuds can’t be used In mono mode.
  2. When SOUNDPEATS Truengine SE Headphones connect with phone equipped with Qualcomrn Snapdragon 855 and higher version chipset, there will be two pairing name appeared on the Bluetooth list and both of them will automatically connect, you don’t need to do the second pairing by manual.
  3. If you want to change pairing device but already in “connected” status with previous one, you can force earbuds to enter into pairing mode-only need press the Multifunction button for 5s.

Factory Reset
(Try the following steps if you fail to build connection between two earpieces or earbuds to device)

  1. Delete pairing name from your device’s Bluetooth list.
  2. Place both earbuds back into the charging case and ensure that both earbuds are In charging status, press and hold both multifunction buttons for 5s until both indicators flash In white twice. Reset complete.

Charging
SOUNDPEATS Truengine SE are equipped with a charging case which is not only a charging dock to charge the headphones but also a carrying case with built-in rechargeable battery, the charging case can provide up to 3.5 times full charge for both headphones.

Charging the headphones
The headphones are partially charged at the factory. Please make sure they are full charged before first use.

  1. Put the earbuds Into corresponding charging slots, make sure the charging contractors are attached.
  2. The LED indicators on the headphones turns red to start charging.
  3. The headphones are fully charged when LED indicators lights out.

Charging The Case
When the charging case is in low battery level, only one white led indicator flashes,please recharge the case:

  1. Connect the charging port with USB charging adapter or computer USB port.(current less than 5V 1A)
  2. Flease charge the earphones at least once every 3 months when not in use for a long time.
Charging The Case

Warranty
We warrant this device 12 MONTHS from date of the originci purchase for manufacturer defects. If the device folk clue to a manufacturing defect, please contact seller directly to innate return and warranty process. g [email protected] www.soundpeatsaudio.com Reuse scan CR code to know the PDF user manual.

https://soundpeatsaudlo.com/downloads/

QR CODE

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B English digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Soundpeats Q32Pro Manual

Soundpeats Q32Pro

USER MANUAL

Soundpeats Q32Pro

Soundpeats
Model: Q32 Pro

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Package Content

Package Content

Product Diagram

Product Diagram

Specifications

Specifications

Wearing

  1. Identify the le and right earbuds.
  2. Insert the earbuds into your ears and adjust to nd best angle with microphone downwards.
  3. Make sure the eartips seal the ear canals.
Wearing

Get Started
Mono Mode

  1. The earbud enters pairing mode directly with a voice prompt “power on” aer being taken out from the charging case. White indicator ashes quickly for around 10s, then red and white indicators ash alternately with a voice prompt “pairing”. “SOUNDPEATS Q32 Pro L” or “SOUNDPEATS Q32 Pro R” would show up on the Bluetooth list, hit it to connect.
  2. If you want to connect two earbuds separately with 2 devices nearby, please connect the le one to one device at rst. In case it will connect to the right earbud automatically aer being taken out from the charging case.

Stereo Mode
Take out both earbuds from the charging case. The two earbuds will ash in white at first. Then the le indicator goes out, and right indicator ashes in red and white. Activate the Bluetooth in your device and hit “SOUNDPEATS Q32 Pro R” on the Bluetooth list.

Factory Reset
(Try the following steps if you fail building connection between two earbuds, or between earbuds and device)

  1. Clear the pairing record between the earbuds and all of your devices.
  2. Hold and press the MFB of both earbuds for 10 seconds when in charging status, the LED indicator will flash red for 3 times if resetting successfully

Charge

  1. Please charge the earbuds at least once every 3 months when not in use for a long time.
  2. To ensure charging safety, please do not use any USB charging adapter with current over 5V 1A. Please do not use quick charger to charge the earbuds and charging case.
Charge

Note:

  1. If you don’t know which device the earbud has already connected, please turn it off then press and hold the button for 5 seconds until red and white indicator flashes alternately to have the earbud enter pairing mode again.
  2. If pairing device is switched off or Bluetooth disconnected, the earbuds will stay in pairing mode for 5 minutes and then power o automatically.
  3. The earbuds can remember previously paired devices. They would automatically connect to the last device they have paired before aer being taken out from the case.

Button Control

Button Control

LED Indicators

LED Indicators

Warranty
We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects.
[email protected]
www.soundpeatsaudio.com
Please scan the QR code or search the link below for detailed PDF manual :
https://soundpeatsaudio.com/downloads/

downloads

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B English digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Soundpeats Force User Mannual

Soundpeats Force

USER MANUAL

Soundpeats Force

Soundpeats Force

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Introduction
Thank you for choosing SoundPEATS Force Wirelessheadphones. Please read the manual carefully, andkeep it for further reference. If you need any assistance,please contact our customer support team by emailing:
[email protected]

Package Content

Package Content

Product Diagram

Product Diagram

Specifications

Specifications

Get Comfortable
Fit in your ears

The Force earphones comes with 6 interchangeable ear Tips and 10 ear fins. The ear tips and ear fins are in different sizes,two of which are equipped on headset. Please choose the right size of ear tips and ear fins to find the most secure and comfortable option for you(normally the medium ones are suitable for 75% of people).

Wearing the headset

  1. Identify the right and left earpieces.
  2. Insert the earbuds into your ears,adjust the ear fins direction and put them into your ears.
  3. Adjust each earpiece until it fits flush in your ear the ear tip seals in the ear canal.
Wearing the headset

Getting Start
Charging

The headset is partially charged in the factory. Please make sure it is fully charged before first use

  1. Connect the charging port with any USB charging adapterstarts automatically with LED indicator turning red and theheadset turns off.
  2. Charging starts automatically with LED indicator turningred and the headset turns off.
  3. The headset is fully charged when the LED indicator turnsblue.

Notes :

  1. The LED indicator flashes red when the battery is low, and you will hear a voice prompt ”battery low”, pleaserecharge the headset.
  2. Charge the headset at least once every 3 months when not using for a long time.
  3. When charging with a USB adapter,the charging current should not be greater than 1A.

Pairing

  1. Please turn off other Bluetooth device nearby and make sure the headset and your Bluetooth device are close enough(within 3 feet).
  2. Power on the headset, press and hold the Multifunctional button for approximately 3 seconds until the LED indicator flashes blue quickly(you will hear the voice prompt “power on” first, just keep holding the multifunctional button ). Now the headset is in pairing model.
  3. Active the Bluetooth function on your device and search for the nearby Bluetooth connection:
    For iPhone/iPad/iPod®: Settings -> Bluetooth -> On For Android™: Setting ->Wireless & Networks -> Bluetooth -> On -> Scan for devices For Windows® Phone devices: Settings -> Bluetooth -> On
  4. “SoundPEATS Force” should be listed in the search result. Select the name to connect. Once connected, the indicator light is solid blue. You will hear a voice prompt“Your headset is connected”.

Notes:

  1. The Force headset will stay in pairing model for 3 minutes at most if no pairing device is found. Afterwards, it will power off automatically.
  2. Maximum operating range for the Bluetooth headset is 33ft(10m) without obstacles. If you move out of range,the headset will lose connection. You will move back to be within the range and reconnect to your Bluetooth audio device.

Re-pairing

The Force Bluetooth headset can remember devices paired before. If you have previously paired the headset with a device, simply turn on your device and the headset(- by pressing the Multifunctional button for 3 seconds)and wait for around 10s, they will automatically connect to each other without going into pairing mode.

Reset
Force earphone can be reset by pressing the Multifunctional button for 3s when the headset is charging. Then the LED Light flashes blue twice.

Control and Voice Notification
Button Controls

Once connected, the Force headset can manage media and phone calls on a smartphone or tablet.

Button Controls

Voice Prompt

Voice Prompt

LED Indicator
The LED indicator gives a good indicator of what the headset is going.

LED Indicator

Trouble Shooting

Q: The headset is on, but it is not connecting to my device?
A: To connect the headset to your device, please check if the Bluetooth of the device is on at first, then select the name of the headset on the Bluetooth list to get paired. If the headset still can’t connect to your device, please try to reset it by reading the reset section.

Q:I have established connection with my smartphone, but I am not hearing any sound?
A:Please make sure that you turn up the volume of both devices. Some smartphones require you to set up the Bluetooth headset as an audio output device before sound is transmitted. Please read the instruction of your smartphone for details. If you are using a music player or other Bluetooth device, please make sure it supports A2DP stereo music profile.

Q: The sound is not very clear / the caller cannot hear my voice clearly?
A: Please adjust the volume on your phone and headset. Make sure there is no signal interference nearby. Stay close to your smartphone.

Q: Can I use the headset while it is charging?
A: No, the headset can not be used while charging.

Q: Why the connection is not stable and cuts out intermittently?
A: Please make sure there are no objects between the headset and your Bluetooth device. Please make sure there is no radio or WIFI interference nearby.

Q: What is the range of Bluetooth headset?
A: Bluetooth headset has maximum range of 33 feet (10m). However, the actual range will depend on usage and environment. Connection is usually good within 15-25 feet with no major obstacles between.

Q: My headset will not switch on.
A: Please recharge it and make sure it has enough battery power. If it is fully charged and still nothing happens or if you are not able to charge the unit, please contact our customer support for warranty cover.

Care and Maintenance

  • Keep the headset away from heat and humidity.
  • Do not put the product under direct sunlight or hot areas.
  • High temperatures will shorten lifespan of the headset, battery and / or the internal circuit board.
  • Power off the headset when not in use and before storing.
  • Do not try to take the product apart.
  • Do not drop or knock your headset on hard surfaces.
  • Do not use chemicals or detergents to clean the product.
  • Do not scrape the surface with sharp objects.

Warranty and Support
Customer Support

If you need any assistance or support, please [email protected] with details.
We will answer your email within 24 hours. We will do our best to provide you with a viable solution.
For more information, please visitwww.soundpeatsaudio.com

Warranty
We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects. If the device fails due to a manufacturing defect, please contact seller directly to initiate return and warranty process.
The following are excluded from SoundPEATS warranty cover:

  • Device purchased as second hand, used or from unauthorized seller.
  • Damage resulted from misuse and abusive action.
  • Damage resulted from chemical, fire, radioactive
  • substance, poison, liquid.
  • Damage resulted from natural disaster.
  • Damage caused to any third party / person / object and beyond.

Statement
We can only provide after sale service for products purchased directly from SoundPEATS or SoundPEATS authorized distributor. If you have purchased from a different seller, please contact them for any exchange or refund.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Questions about your Manual ? Post in the comments!