WM Systems M2M Easy 2S Security Communicator

LIEKETSENG LEKHOTLA

1. SIM card slot (mofuta oa 2FF, push-insert)
2. Sehokelo sa Antenna (SMA-50 Ohm, mosali)
3. PWR -/+: Sehokelo sa thapo ea matla (8-24VDC, 1A), khokahano ea betri 4 – IN1, IN2 -/+: lihokelo tsa thapo tsa motlakase (bakeng sa li-sensor, sabotagho lemoha) 5 - Li-Jumpers bakeng sa ho khetha mekhoa ea line ea ho kenya (bakeng sa IN1, IN2):
   • galvanically indepentent voltage inputs
   • lintlha tsa ho ikopanya (ho lemoha terata e khaotsoeng (ka ho sebelisa 10kΩ EOL resistor), kapa e khutšoanyane)
4. Maemo a li-LED
5. HO TSOA: tlhahiso ea relay (bakeng sa taolo: ho bula heke kapa siren / makhapetla)
6. ALR: Alamo (TIP RING) mohala oa ho hokela setsi sa alamo (mohala oa mohala oa analog o etsisitsoeng)
7. PROG: Sehokelo sa RJ11 (bakeng sa tlhophiso, nchafatso ea software)
8. Likoti tsa ho tiisa boto ea PCB (ka lebokoseng la tšireletso la alamo, joalo-joalo)
9. Sehokelo sa boto ea katoloso (bakeng sa IO-expander)
   Khetho ea mokhoa oa ho kenya letsoho (ka li-jumpers [5]):

Mokhoa oa ho kenya lebitso (bakeng sa ho khaola ha cable / ho lemoha nako e khutšoanyane kapa li-sensor)

• Li-jumpers tse amanang le tsona (haufi le 2-pins, haufi le sehokelo sa ho kenya)
• Ntlha ea motheo ea mela e kenyang (-) e tloaelehile
• Khokahano ea mela e kenang (polarity e ikemetseng)

Moqtage

• Li-jumpers tse amanang le tsona (haufi le li-2-pins ho li-LED tsa ho kenya)
• Galvanical e ikemetseng, mela e kenang ka bomong
• Ela hloko polarity ha wiring!

KABELO EA MATLA LE MAEMO A TIKOLOHO 

• Phepelo ea motlakase: 8-24 VDC
• Letšoao la ho kenya: boemo bo phahameng 2-24V (IO-expander: 2-32V), boemo bo tlaase: 0-1V
• Boemong ba hona joale: 0.33mA
• Switchable voltage ka tlhahiso: 2A / 120VAC; 1A / 24VDC
• Tshireletso: IP21
• Mocheso oa ts'ebetso o pakeng tsa -40°C le+70°C, polokelo e pakeng tsa -40°C le+80°C, ka mongobo oa 0-95%
• Boholo: 96 x 77 x 22mm, boima: 160 gr
• Ho tiisa / ho phahamisa: e kanna ea ts'oaroa ke li-screw tse 4 / li-spacers tsa polasetiki ka masoba a 4 ho PCB

LIEKETSENG MOHATO

• Mohato oa 1: Beha SIM ka har'a terei ea SIM [1] (lehlakore la chip le shebile fatše 'me moeli o sehiloeng oa SIM o shebile lehlakoreng la PCB).
• Mohato oa 2: Sututsa SIM ho fihlela e tla lokisoa.
• Mohato oa 3: Wila le ho hokela mela (s) ea ho kenya (li sebelise bakeng sa lisensara kapa sabotage discover) ka voltage/contact mode - ka ho kenya likhoele ho IN1, IN2 [4]. Khetha mokhoa oa ts'ebetso oa mohala oa ho kenya, khetha boemo ba jumper [5] (voltage/kopana). Hokela tlhahiso (bakeng sa ho chencha sesebelisoa sa kantle / sistimi ea ho bula heke) ho OUT [7].
• Mohato oa 4: Haeba u batla ho hokela setsi sa alamo ho transmitter ea rona ea polokeho, hokela TIP RING ea setsi sa alamo ho boema-kepe ba ALR [8].
• Mohato oa 5: Hokela lenakana ho sehokelo sa SMA [2].
• Mohato oa 5: Lenaneng la puisano la setsi sa alamo, kenya bonyane nomoro e le 'ngoe ho nomoro ea mohala ea leihlo e hole. Haeba u lakatsa ho sebelisa M1M Easy 2 ka mokhoa oa GSM hape (e le tsela ea mantlha kapa ea bobeli), kenya nomoro ea mohala ea GSM. ea tšebeletso ea dispatcher ho kena setsing sa alamo.
• Mohato oa 6: Hokela lehlakore la RJ11 la cable ea RJ232-RS11 ho PROG e nang le sehlooho se reng [9], hokela ka lehlakoreng le leng la thapo (RS232 coonector) ho thapo ea adaptara ea RS232-USB ho khona ho hokela komporong. Etsa tlhophiso ka sesebelisoa sa EasyTerm ho latela karolo e amanang le Bukana ea Mosebelisi.
• Mohato oa 7: Khoasolla software ea EasyTerm ka sehokelo sena (Windows® 7/8/10 ea sebetsa):
  https://www.m2mserver.com/m2m-downloads/EasyTerm_v1_3_5__EN.zip
• Mohato oa 8: Khoasolla firmware ea morao-rao bakeng sa ho nchafatsa software: https://www.m2mserver.com/m2m-downloads/EASY2S_V21R08C02.bin
• Mohato oa 9: Ntša EasyTerm .ZIP file 'me u phethe EasyTerm_v1_3_5.exe file. Latela mehato ea bukana ea ho kenya Khaolo ea 4, 5.
• Mohato oa 10: Hokela thapo ea motlakase ea 12V/24V DC ea lithapo tsa motlakase tsa setsi sa alamo ho boema-kepe bo nang le sehlooho se reng PWR [3]. (Ela hloko haholo polarity ea terata! Mohala o ka letsohong le letšehali oa PWR ke positi (+), ka ho le letona ke negative (-). U ka sebelisa adaptara ea motlakase ea 124V DC 1A hape.)
• Mohato oa 11: Joale sesebelisoa se tla ba tlas'a voltage, 'me e tla be e bulela le ho qala ts'ebetso ea eona. PWR LED e tala e tla lula e khantša. Boemo bofe kapa bofe bo bong ba ts'ebetso ea LED bo thathamisitsoe mona.

BOHLOKOA! Haeba ho se na PC e fumanehang, o ka seta liparamente tsa sesebelisoa ka melaetsa ea mongolo ea SMS (ka ho sebelisa litaelo tse lumellanang).

MAEMO LED LITŠOANTŠISO

LED	Mosebetsi	Tlhaloso	Mmala oa LED	Boitšoaro
GSM	Matla a leqhubu la marang-rang a cellular	Ho saena matla a lets'oao a teng - ho benya ho feta = matla a mats'oao a betere	khubelu	tse benyang
STA	Boemo ba modem	Tabeng ea ts'ebetso e tloaelehileng e saena boemo ba puisano ea marang-rang a selefouno	mosehla	tse benyang/mabone
IN1	Kenyelletso nr.1	E tšoaea boemo ba mohala oa #1 oa ho kenya (I1INV kapa IDELAY ho sebelisoa paramente) The LEDislightingiftheinputwiresareclosed(active)	botala	mabone
IN2	Kenyelletso nr.2	E tšoaea boemo ba mohala oa #2 oa ho kenya (I2INV kapa IDELAY ho sebelisoa paramente) The LEDislightingiftheinputwiresareclosed(active)	botala	mabone
TSOA	Phatlalatso ea tlhahiso	Lebone la LED ha lerelay le koetsoe, eseng mabone: ha relay e buloa	mosehla	mabone
MDM RDY	Ts'ebetso ea modem	Boemo ba modem. E benya ka linako tse ling haeba e sebetsa ka mokhoa o bonolo, e fumanehang habonolo.	khubelu	tse benyang
ALR	Setsi sa alamo	Boemo ba mohala oa setsi sa alamo (Tip-Ring) Sebuela-pele se khanngoe: ha se khantšitsoe, Sebui se tima: ha ho setsi sa alamo	botala	tse benyang
PWR	Matla	E bontša boteng ba phepelo ea motlakase ea processor	botala	mabone

STA LED - e na le mekhoa e meraro:

• mabone a sa khaotse: pontšo ea ho qetela ea GPRS e atlehile,
• e timiloe: Mokhoa oa ts'ebetso oa GSM, ha ho phoso
• 'x' palo ea khanya ka nako ea metsotsoana e 3: khoutu ea phoso:
  1. flash: Ho hloleha ha module
  2. ho benya: Ho hloleha ha SIM card
  3. ho benya: E hlolehile ho netefatsa PIN
  4. ho benya: Sesebelisoa ha se khone ho kena ho netweke ea GSM
  5. ho benya: Sesebelisoa ha se khone ho kena ho netweke ea mehala
  6. ho benya: E hoketsoe ho netweke ea mehala, empa ha e khone ho kena ho seva

 

• GSM LED: Lipalo tsa khanya ea LED li saena matla a lets'oao la marang-rang a cellular (ho benya ho feta ho bolela kamohelo e ntle ea matšoao). Ho na le khefutso ea metsotsoana e 10 lipakeng tsa tatellano e 'meli e benyang. Leseli le nka 50 msec, ebe ho robeha halofo ea bobeli ho tla, joalo-joalo.
• Moelelo oa ho khanya (lipalo): 0: Phoso, 1: Ho fokola, 2-3: Karolelano, 4-5: E ntle, 6-7: E ntle haholo
• IN1, IN2 LED: Ha kenyeletso e sebetsa (haeba lithapo tse peli li koetsoe; kapa ka mokhoa oa matla ho 5-24VDC voltage teng) e amanang le INx LED e tla khantša.
• LED E TSOANG: Ho khantša ha tlhahiso e sebetsa (lithapo tsa relay li koetsoe). E bontša boemo ba "primer-side" ea relay.
• LED ea MODEM ea RDY: Mojule oa ts'ebetso ea LED, e panyang ka potlako ha ho qalisoa Easy2S (hoo e ka bang habeli ka metsotsoana). Ha modem e se e fumaneha ebile e sebetsa 'me e na le puisano e sebetsang ho marang-rang a GSM, joale e tla khantša hangata.

MEKHOA TS'EBETSO

Sesebelisoa se khona ho hlophisa le ho sebelisa mekhoa le mesebetsi e latelang:

1. GSM transmitter (e lokiselitsoeng pele ho mokhoa ona, ka ho sa feleng): sesebelisoa sa alamo se hokahane le tlhahiso ea TIP-RING, li-code tsa ID tse kenang li tla fetisetsoa le ho fetisoa ka marang-rang a GSM ho ea setsing sa ho romella se hole.
2. Ho saena ho Enigma IP receiver / SIMS Could®: sesebelisoa sa alamo se hokahane le tlhahiso ea TIP-RING, li-code tsa ID tse kenang li tla fetisetsoa le ho fetisoa ka marang-rang a cellular a 2G / 3G ka Enigma protocol ho Enigma IP receiver kapa ho kenngoa ho SIMS® software.
3. Ho fetisetsa ka marang-rang a cellular ho ea setsing sa thomello: tsamaiso ea alamo e hokahane le tlhahiso ea TIP-RING, sabotage switch e hokahane le ho kenya letsoho bakeng sa ho beha leihlo, matšoao a kenang a fetoleloa ho likhoutu tsa ID tsa Contact li tla fetisoa ka marang-rang a cellular ho aterese ea IP ea setsi sa ho romella.
4. Sistimi ea alamo e ikemetseng - e nang le tsebiso ea SMS feela: sensor kapa sabotagho lemoha. Li-sensor li hokahane le mela ea ho kenya (bakeng sa lintlha tse 2 / ka IO-expansion max. 8 inputs); siren ea alamo e ka kopanngoa le tlhahiso. Lipontšo li tla fetisoa ka marang-rang a cellular ho IP seva.
5. Ho beha leihlo, ho buloa ha heke: lisensara kapa sabotagho lemoha. Li-sensor li hokahane le 2 voltage/contact inputs (ka IO-expansion max. 8 inputs). Kenyelletso e khuts'oane / terata e sehiloeng e ka bonoa ho tse kenang. Sehlahisoa sa relay (s) se laoloa ka thōko (sehlahisoa sa nr # 1. ke sa ho bula heke, liphello tse ling (nr. 2-4) li hlahisoa bakeng sa ho fetola lisebelisoa tsa ka ntle). Lisebelisoa li sebelisa marang-rang a cellular ka mokhoa ona bakeng sa taolo e hole. Marang-rang a GSM a sebelisetsoa tsebiso le ho lla ka SMS. Letšoao ka marang-rang a cellular (ho ea atereseng ea IP) le ntse le le teng e le khetho.

TLHOKOMELISO KA KHOPOTSO SERIALI
Sesebelisoa se romelloa ka firmware e kentsoeng le tlhophiso ea feme. Ka nako e sa lekanyetsoang, Easy2S e sebetsa e le mochine oa GSM (lipontšo tsa tsamaiso ea alamo e hokahaneng (ho Tip-Ring) e tla fetisoa ka marang-rang a GSM - ka li-code tsa Contact ID - ho setsi sa dispatcher).
Litlhoko tse ling tsa tlhophiso li ka hlophisoa ka software ea EasyTerm®. Hokela lehlakore la RJ11 la cable ea RJ232-RS11 koung ea RJ11 ea sesebelisoa 'me u sebelise thapo ea adaptara ea RS232-USB ho e hokela komporong ea hau.

TLHOKOMELO KA MELAO EA SMS

• U ka romela litaelo tse ling ka molaetsa o tšoanang oa mongolo oa SMS. Litaelo tsa lipotso li ke ke tsa tsoakoa le litaelo tsa taolo!
• Max. Litlhaku tse 158 li ka sebelisoa molaetseng o le mong oa SMS. Melaetsa e tlameha ho ba le litlhaku tse kholo tsa Senyesemane tsa alfabeta feela kapa linomoro.
• Taelo le karohano ea litaelo lia khoneha ka lets'oao la koma ntle le tlhaku ea sebaka. Boleng ba paramethara (kamora = sebopeho) bo ka ba le letho.
• Molaetseng o mong le o mong oa SMS (!) u tlameha ho sebelisa parameter ea password (PW) sebakeng sa pele sa taelo.
• U tlameha ho sebelisa taelo ea RESET molaetseng oa ho qetela oa parameter ea SMS, qetellong boemo - joalo ka PW=ABCD,……,RESET
• Lipehelo tse ncha li qala ho sebetsa feela ka mor'a ho qala bocha. Kamorao - metsotso e mmalwa - o rometse molaetsa wa ho qetela wa paramethara o tla fumana karabo ho tswa ho sesebediswa hore na ho sebeditswe diparamente tse kae (mohlala, "Litlhophiso li lokile!" Karabelo ea molaetsa oa mongolo)
• Phasewete ea kamehla ke ABCD, e ka fetoloang (PWNEW param.) e ka bang max. Likotoana tse 16.
• Example: PW=ABCD,APN=TELEMATICS.NET,SERVER1=1.1.1.1,RESET Karabelo ya molaetsa wa mongolo: Di-setting OK!

LITS'ELISITSO TSE KHOLO	Tlhaloso
PW	Khokahano / netefatso ea password (ea kamehla: ABCD)
PWNEW	Ho fetola phasewete, ho eketsa phasewete e ncha bakeng sa netefatso ea khokahano
APN	Lebitso la netweke ya APN e hlokehang bakeng sa kgokelo ya netweke ya cellular, e fanoeng ke opareitara e fanang ka SIM card
MOSEBETSI1	Aterese ea mantlha e tsitsitseng ea IP ea leihlo le hole (setsi sa dispatcher) bakeng sa ho amohela matšoao a ho fetisa.
POTSO1	Nomoro ea boema-kepe bakeng sa aterese ea mantlha e tsitsitseng ea IP ea setsi sa dispatcher, moo matšoao a tla amoheloa (kamehla=9999)
GPRSEN	E nolofalletsa puisano ea marang-rang ea cellular. Maemo: 1=nomella, 0=thibela (kamehla=0)
SWPROTO	Ke protocol efe e sebelisetsoang ho bontša. Boleng: 2=Tlhakatsi (protocol e tloaelehileng ea ID), 1=M2M (ea kamehla=2) (M2M e bolela protocol e fetotsoeng ea Contact ID, e ka sebelisoang feela le ba amohelang IP ba latelang (joalo ka Enigma II).®, Pherekano IP2® receivers) hole software ea dispatcher (joalo ka AlarmSys® le SIMS® software)).
ACCOUNT	Khoutu ea boitsebahatso ea moreki, nomoro ea ntho e tla sebelisoa bakeng sa matšoao a hau, mats'oao (a lintho tse kenang) tse rometsoeng ke sesebelisoa (default=0001). Ho khothalletsoa ho theha nomoro ea ntho e tšoanang le e behiloeng setsing sa alamo!
MOSEBETSI	U ka khetha hore aterese ea IP ea mantlha kapa ea bobeli e tla ba ea pele ka tatellano ea lipontšo
DTMFTIME	DTMF khefutsa pakeng tsa matshwao a ID ya TIP-RING
IPPROTO	TCP kapa protocol ea puisano ea UDP ho latela litlhoko tsa ho lumellana
LFGSMREQ	Maqhubu a lets'oao la bophelo la GSM - boleng ka metsotsoana (kamehla = 60)
LFFREQ	Khafetsa ea lets'oao la bophelo ba netweke ea cellular - boleng ka metsotsoana (default=300)

POTSO MELAO	Likahare tsa karabo
INFDEV (kapa) DEVSTAT	E tla arabela tlaleho ea SMS e nang le boemo ba hajoale ba Ho bonolo 2: akhaonto nr. (ID ea moreki), matla a lets'oao, mofuta oa software, ID ea sesebelisoa, IMEI ea sesebelisoa, SIM ICC, boemo ba betri, aterese ea IP (ACCOUNT, SQ, SWVER, HWID, IMEI, SIMICC, VBATT, IP)
INFIO	Boemo ba hona joale ba mela ea ho kenya le mola oa tlhahiso. E na le: ACCOUNT, SQ, boemo ba hajoale ba mela e kenang / e hlahisoang
INFLEL	Litlhophiso tse hlophisitsoeng tsa tsebiso ea lentsoe/SMS, linomoro tsa mohala le tsebiso (molaetsa oa mongolo oa SMS) tatelano ea tatellano ea tatellano ea mohala oa lentsoe (ho lla) tatellano e tla ba karabo. E na le: ACCOUNT, SQ, TEL1, TEL2, TEL3, TEL4, I1S, I2S, I1V, I2V
INFSMS	Kenya litlhophiso tsa tsebiso ea SMS. E na le: ACCOUNT, SQ, I1ON, I1OFF, I2ON, I2OFF
INFIP	Litlhophiso tsa khokahano ea seva. E na le: ACCOUNT, SQ, IMEI, IP, SERVER1, PORT1, SWPROTO

MOLAETSA WA SMS (TAELO TSA TAELO) EXAMPLES: 

• Phatlalatso ea GSM / phetiso: PW=ABCD,GPRSEN=0,SYS1=1,ACCOUNT=1130,LFGSMFREQ=60,DTMFTIME=60,RESET
• Ho tuma ka marang-rang a cellular ho IP-receiver: PW=ABCD,GPRSEN=1,SFUNCT=1,ACCOUNT=1130,LFFREQ=300,APN=NET,SERVER1=89.133.189.139, PORT1=9999,IPPROTO=UDP,RESET

Bakeng sa litekanyo tse ling tse fumanehang, bala Tataiso ea ho Kenya e ka khoasolloang ka software e hlokahalang le firmware ho tsoa ho rona websebaka: https://m2mserver.com/en/product/wireless-safety-transmitter/

Sehlahisoa sena se tšoailoe ka letšoao la CE ho latela melaoana ea Europe.

Litokomane / Lisebelisoa

	WM Systems M2M Easy 2S Security Communicator [pdf] Tlhophiso Tataiso M2M Easy 2S Security Communicator, M2M, Easy 2S Security Communicator, 2S Security Communicator, Security Communicator, Communicator
	WM Systems M2M Easy 2S Security Communicator [pdf] Tlhophiso Tataiso M2M Easy 2S Security Communicator, M2M, Easy 2S Security Communicator, 2S Security Communicator, Security Communicator, Communicator

Litšupiso

• Bukana ea Mosebelisi