Bukana ea mosebelisi bakeng sa
EV200 letoto la Variable Frequency Drive
Outsize
| Moqtage | Mofuta oa mohlala | Matla(kW) | Kenya boholo(mm) | boholo (mm) | Kenya lesoba | |||
| A | B | W | H | D | ||||
| Karolo e le 'ngoe ea 220V | EV200-0400G-S2 | 0. 4 |
60 |
129 |
73 |
143 |
112. 6 |
Ф4.4 |
| EV200-0750G-S2 | 0. 75 | |||||||
| EV200-1500G-S2 | 1. 5 | |||||||
| EV200-2200G-S2 | 2. 2 | |||||||
|
Karolo e meraro ea 380V |
EV200-0750G-T3 | 0. 75 | ||||||
| EV200-1500G-T3 | 1. 5 | |||||||
| EV200-2200G-T3 | 2. 2 | |||||||
| EV200-3700G-T3 | 3. 7 | 73 | 168 | 85. 5 | 180 | 116. 4 | Ф4.4 | |
| EV200-5500G-T3 | 5. 5 | |||||||
Setšoantšo se tloaelehileng sa Wiring
Lisebelisoa tsa lithapo
| Letšoao la terminal | Tlhaloso ea mosebetsi |
| E | Setsi sa boema-fofane |
| L1, L3 | Hokela ho grid ea motlakase mohatong o le mong (220Vac) phepelo ea motlakase ea AC |
| L1, L2, L3 | E hoketsoe keriting ea mekhahlelo e meraro (380Vac) phepelo ea motlakase ea AC |
| U, V,W | Hokela motlakase oa AC oa mekhahlelo e meraro |
| B1 | Sefa capacitor DC lehlakore voltage positive terminal |
| B2 | Mohanyetsi oa braking oa DC o ka hokahanngoa ka kotloloho ho B1 |
Lintlha tsa tekheniki
| Ntho | Tlhaloso | |
| Maqhubu a phahameng ka ho fetisisa | Taolo ea Vector: 0～500Hz; Taolo ea V/F: 0～500Hz | |
| Khafetsa ea mopalami | 0.8kHz ～ 12kHz Maqhubu a Carrier a ka fetoloa ka bohona
ho latela litšobotsi tsa mocheso |
|
| Qeto ea ho kenya | Boemo ba dijithale: 0.01Hz Boemo ba Analog: makhetlo a mangata × 0.025% | |
| mokhoa oa ho laola | ntle le PG Vector(SVC), Feedback vector(FVC) le V/F control | |
| Qala torque | Mofuta oa G: 0.5Hz/150% (SVC);0Hz/180% (FVC) mofuta oa P: 0.5Hz/100% | |
| Lebelo la lebelo | 1:100 (SVC) | 1:1000 (FVC) |
| Ho nepahala ha taolo ea lebelo | ±0.5% (SVC) | ±0.02% (FVC) |
| Ho nepahala ha taolo ea torque | ±5% (FVC) | |
| Bokhoni ba ho tlala | Mofuta oa G: 150% e lekantsoe hona joale 60sec; 180% e lekantsoe 3sec ea hajoale | |
Funcon Parameters Tafole
Ha PP-00 e behiloe e le boleng boo e seng ba zero, ke hore, password ea protecon ea parameter e behiloe. Ho parameter ea funcon mme mosebelisi o fetola mokhoa oa paramente, menyu ea paramente e tlameha ho kenya phasewete ka nepo. E ka hlakola password ea protecon funcon ka seng PP-00 joalo ka 0.
Menu ea paramethara ka har'a mokhoa o hlalositsoeng ke mosebelisi ha e sirelelitsoe ka password.
Sehlopha sa P le A li kenyelletsa liparamente tsa motheo tsa funcon, sehlopha sa d se kenyelletsa liparamente tsa funcon tsa ho beha leihlo. Matšoao a tafoleng ea khoutu ea funcon a hlalosoa ka tsela e latelang:
"☆" : hoa khoneha ho fetola parameter ha koloi e eme kapa e le boemong ba ho matha;
“★”: ha ho kgonehe;
“●”:paramethara ke boleng bo lekantsweng ba nnete mme e ka se fetoswe.
"*" : parameter ke "parameter ea fektheri", e ka behoa feela ke moetsi, e thibela mosebedisi ho sebetsa.
| Khoutu ea Mosebetsi | Lebitso | Setting Range | Ea kamehla | Fetola |
| Sehlopha sa P0: Mosebetsi oa Motheo | ||||
| P0-01 | Motor 1 mokhoa oa ho laola | 0: Ha ho taolo ea vector ea sensor ea lebelo (SVC) 1: Taolo ea vector ea sensor ea lebelo (FVC) 2: taolo ea V/F | 2 | ★ |
| P0-02 | Khetho ea mohloli oa taelo | 0: Lekanale la litaelo tsa phanele ea ts'ebetso 1: Seteishene sa taelo ea terminal 2: mocha oa taelo ea puisano | 0 | ☆ |
|
P0-03 |
Tlhophiso e kholo ea litšupiso tsa maqhubu Kgetho ya kanale |
0: tlhophiso ea dijithale (maqhubu a preset P0-08, UP / TLASE a ka fetoloa, matla ha se mohopolo) 1: boemo ba dijithale (maqhubu a preset P0-08, UP / TLASE a ka fetoloa, mohopolo oa ho theola matla 2: AI1 (Hlokomela : J4 jumper ka PANEL le AI1 e hoketsoeng ho keyboard potentiometer input, PORT le AI1 tse hokahaneng le theminale ea kantle ea AI1 input) 3: Ai2 4: Ai3
5:High-speed pulse Inputsetting (S5) 6: ditaelo tsa dikarolo tse ngata 7: E Bonolo PLC 8: PID 9: puisano e fuwe 10: E boloketswe |
2 |
★ |
|
P0-04 |
Mohloli o thusang oa maqhubu B khetho ea ho kenya taelo | Ka P0-03 (mohloli o moholo oa maqhubu A khetho ea taelo) |
0 |
★ |
| P0-05 | Auxiliay frequency source B Kgetho ya ntho ya tšupiso | 0: e amanang le maqhubu a phahameng a 1: e amanang le mohloli oa khafetsa A | 0 | ☆ |
| P0-06 | Mohloli o thusang oa maqhubu B lethathamo la litaelo | 0%~150% | 100% | ☆ |
|
P0-07 |
Khetho ea mokhoa oa ho kopanya mohloli oa khafetsa |
Bit: khetho ea mohloli oa maqhubu 0: Mohloli o moholo oa maqhubu A 1: liphetho tsa ts'ebetso tse ka sehloohong le tse thusang (kamano ea ts'ebetso e khethiloeng ke leshome) 2: Mohloli o moholo oa maqhubu A le mohloli oa maqhubu a thusang B switjha 3: Mohloli o moholo oa maqhubu A le ho fetola sephetho sa ts'ebetso ea master le lekhoba 4: Mohloli o thusang oa maqhubu a B le sephetho sa ts'ebetso ea master le ea makhoba ho fetoha Leshome: kamano ea mantlha ea mohloli le ts'ebetso e thusang
0: ea mantlha + e thusang 1: ea mantlha - e thusang 2: boholo ba bobeli ke 3: bonyane tse peli |
00 |
☆ |
| P0-08 | Maqhubu a behiloeng esale pele | 0.00Hz ~ max(P0-10) maqhubu | 50.00Hz | ☆ |
| P0-09 | Tsela ea ho matha | 0: tsela e tšoanang 1: tsela e fapaneng | 0 | ☆ |
| P0-10 | Max.output frequency | 50.00Hz ~ 500.00Hz | 50.00Hz | ★ |
| P0-11 | Ho beha mocha oa moeli o ka holimo oa maqhubu | 0: P0-12 e behiloe 1:AI1(Hlokomela:J6jump) 2: AI2 3: AI3 4: Boemo ba lebelo le phahameng la sekhahla (S5)
5: puisano e fanoeng |
0 | ★ |
| P0-12 | Moeli oa litšupiso tsa khafetsa | Moeli o ka holimo P0-10 P0-14 ~ max frequency | 50.00Hz | ☆ |
| P0-13 | Maqhubu a litšupiso tse ka holimo-limo | 0.00Hz ~ maqhubu a mangata. P0-10 | 0.00Hz | ☆ |
| P0-14 | Moeli o tlase oa Reference | 0.00Hz ~ maqhubu a holimo moeling oa P0-12 | 0.00Hz | ☆ |
| P0-15 | Khafetsa ea mopalami | 0.8KHz ~ 12.0KHz | E itšetlehileng ka mohlala | ☆ |
| P0-16 | Maqhubu a mochini a tsamaisanang le mocheso | 0: E holofalitsoe 1: E lumelletsoe | 1 | ☆ |
| P0-17 | Nako ea ho potlakisa 1 | 0.00s ~ bo65000 | E itšetlehileng ka mohlala | ☆ |
| P0-18 | Nako ea ho phomola 1 | 0.00s ~ bo65000 | E itšetlehileng ka mohlala | ☆ |
| P0-19 | Setsi sa ho potlakisa/ Ho fokotsa nako | 0: 1s 1: 0.1s 2: 0.01s | 1 | ★ |
|
P0-21 |
Khafetsa ea ho fokotseha ha mocha oa litlhophiso tsa maqhubu a thusang bakeng sa lipalo tse kholo le tse thusang |
0.00Hz~ max.frequency P0-10 |
0.00Hz |
☆ |
| P0-22 | Qeto ea litšupiso tsa khafetsa | 2:0.01Hz | 2 | ★ |
| P0-23 | E boloka maqhubu a dijithale ha o emisa | 0: se hopole 1: mohopolo | 1 | ☆ |
| P0-24 | Khetho ea sehlopha sa paramethara ea likoloi | 0: Paramethara ea pele ea 1: paramente ea 1 ea koloi | 0 | ★ |
| P0-25 | Acceleration/ Ho fokotsa lebelo la motheo la nako | 0: boholo (P0-10) 1: Seta maqhubu a 2: 100Hz maqhubu | 0 | ★ |
| P0-26 | Base frequency bakeng sa phetoho ea UP/DOW nakong ea ho sebetsa | 0: Matha frequency 1: Beha maqhubu | 0 | ★ |
|
P0-27 |
Taelo ea ho matha e tlameletsoe mohloling o ka sehloohong oa maqhubu A khetho ea taelo |
Bit: Taelo ea phanele ea ts'ebetso Tlama khetho ea mohloli oa maqhubu 0: ha ho tlamo 1: Nako ea ho seta dijithale 2: AI1 (Hlokomela: J6 jumper) 3: AI2 4: AI3 5: Setting ea ho kenya letsoho ka lebelo le phahameng (S5) 6: lebelo le fapaneng 7 : E bonolo PLC 8: PID 9: puisano e fanoeng Leshome: Terminal Command Binding Frequency Frequency Selection Makholo-kholo: taelo ea puisano e tlamang khafetsa khetho ea mohloli |
0 |
☆ |
| P0-28 | serial port communication protocol | 0: Puisano ea Modbus | 0 | ☆ |
| Sehlopha sa P1: Motor 1 Parameters | ||||
| P1-00 | Khetho ea mofuta oa koloi | 0: Enjene e tloaelehileng ea asynchronous 1: Enjene e feto-fetohang ea asynchronous motor | 0 | ★ |
| P1-01 | Matla a motlakase a lekantsoeng | 0.1KW ~ 1000.0KW | E itšetlehileng ka mohlala | ★ |
| P1-02 | Rated motor voltage | 1V ~ 2000V | E itšetlehileng ka mohlala | ★ |
| P1-03 | E lekantsoe motlakase oa motlakase | 0.01 ho 655.35A (AC drive matla ≤ 55 KW)
0.1 ho isa ho 6553.5A (matla a koloi ea AC> 55 KW) |
E itšetlehileng ka mohlala | ★ |
| P1-04 | Rated motor frequency | 0.01Hz ~ boholo. makhetlo a mangata | E itšetlehileng ka mohlala | ★ |
| P1-05 | E lekanyelitsoe lebelo la koloi | 1rpm ~ 65535rpm | E itšetlehileng ka mohlala | ★ |
| P1-06 | Ho hanyetsa stator | 0.001Ω~65.535Ω(AC drive power≤55KW) 0.0001Ω~6.5535Ω(AC drive power>55KW) | Ho ipapisitse le tokiso ea othomathike | ★ |
| P1-07 | Ho hanyetsa ha rotor | 0.001Ω~65.535Ω(AC drive power≤55KW) 0.0001Ω~6.5535Ω(AC drive power>55KW) | Ho ipapisitse le tokiso ea othomathike | ★ |
| P1-08 | Leakage inductive reactance | 0.01mH~655.35mH(AC drive power≤55KW) 0.001mH~65.535mH
(Matla a koloi ea AC> 55KW) |
Ho ipapisitse le tokiso ea othomathike | ★ |
| P1-09 | Boiketlo ba ho kopanya | 0.1mH~6553.5mH(AC drive power≤55KW) 0.01mH~655.35mH(AC drive power>55KW) | Ho ipapisitse le tokiso ea othomathike | ★ |
| P1-10 | Ha ho mojaro oa hajoale | 0.01A~P1-03(AC drive power≤55KW) 0.1A~P1-03(AC drive power>55KW) 0.1A~P1-03(AC drive power>55KW) | Ho ipapisitse le tokiso ea othomathike | ★ |
| P1-27 | Encoder pulses per revolution | 1-65535 | 1024 | ★ |
| P1-28 | Mofuta oa encoder | 0: ABZ keketso ea khouto 2: Tharollo | 0 | ★ |
| P1-30 | Tatelano ea mohato oa A/B oa ABZ e khouto e ntseng e eketseha | 0: Pele 1: Boloka | 0 | ★ |
| P1-34 | Palo ea lipara tsa lipalo tsa sehlahisoa | 1-65535 | 1 | ★ |
| P1-36 | Nako ea ho lemoha phoso ea Encoder wire-break | 0.0: ha ho ts'ebetso 0.1s ~ 10.0s | 0.0s | ★ |
|
P1-37 |
Khetho ea mokhoa oa ho lokisa likoloi |
0: ha ho ts'ebetso ea 1: Mochini oa Asynchronous static karolo ea liparamente tsa ho ithuta 2: Mochini oa asynchronous o matla oa ho ithuta ka botlalo |
0 |
★ |
| Sehlopha sa P2: Mekhahlelo ea Taolo ea Vector | ||||
| P2-00 | Speed loop portional gain 1 | 1-100 | 30 | ☆ |
| P2-01 | Nako ea bohlokoa ea loop 1 | 0.01s ~ bo10.00 | 0.50s | ☆ |
| P2-02 | Switchover frequency 1 | 0.00~P2-05 | 5.00Hz | ☆ |
| P2-03 | Speed loop portional gain 2 | 1-100 | 20 | ☆ |
| P2-04 | Nako ea bohlokoa ea loop 2 | 0.01s ~ bo10.00 | 1.01.00s0s | ☆ |
| P2-05 | Switchover frequency 2 | P2-02~ max frequency (P0-10) | 10.00Hz | ☆ |
| P2-06 | Phaello ea matšeliso a SVC/FVC | 50%~200% | 100% | ☆ |
| P2-07 | Sesefa sa maikutlo a SVC Speed nako e sa fetohe | 0.000s ~ bo0.100 | 0.015s | ☆ |
|
P2-09 |
Torque e holimo moeli oa khetho ea mocha tlas'a taolo ea lebelo |
0: khoutu ea ts'ebetso P2-10 tlhophiso ea 1: AI1 2: AI2 3: AI3
4: lebelo le phahameng la pulse input setting (S5) 5: puisano e fanoeng 6: MIN (AI1, AI2) 7: MAX (AI1, AI2) 1-7 kgetho tekanyo e feletseng e lumellana le P2-10 |
0 |
☆ |
| P2-10 | Litlhophiso tsa dijithale tsa moeli oa torque taolong ea lebelo | 0.0%~200.0% | 150.0% | ☆ |
|
P2-11 |
Mohloli oa moeli oa torque taolong ea lebelo (e boemong bo bocha) |
0: Tlhophiso ea khoutu ea ts'ebetso P2-12 (ha ho na phapang pakeng tsa motlakase le motlakase) 1: AI1 2: AI2 3: AI3 4: Kemiso ea ho kenya letsoho ka lebelo le phahameng 5: puisano e fanoeng 6: MIN (AI1, Ai2) 7: MAX ( AI1, AI2)
8: Mokhoa oa ho sebetsa oa P2-12 1-7 Tekanyo e feletseng ea khetho e lumellana le P2-12 |
0 |
☆ |
| P2-12 | Litlhophiso tsa dijithale tsa moeli oa torque taolong ea lebelo (maemong a ntlafatso) | 0.0%~200.0% | 150.0% | ☆ |
| P2-13 | Phetoho ya boithatelo phaello e lekanang | 0-60000 | 2000 | ☆ |
| P2-14 | Phaello ea bohlokoa ea phetoho ea excitation | 0-60000 | 1300 | ☆ |
| P2-15 | Torque torque phaello e lekanang | 0-60000 | 2000 | ☆ |
| P2-16 | Torque phetoho ea bohlokoa phaello | 0-60000 | 1300 | ☆ |
| P2-17 | Khetho ea karohano ea lebelo la loop | 0: E holofalitsoe 1: E lumelletsoe | 0 | ☆ |
| P2-20 | Boholo ba tlhahiso ea matlatage | – | – | – |
| P2-21 | Max. torque coefficient ea sebaka se fokolang sa tšimo | 50~200% | 100% | ☆ |
| P2-22 | Khetho ea moeli oa matla a tsosolosang | 0: E holofalitsoe 1: E lumelletsoe | 0 | ☆ |
| P2-23 | Moeli oa ho tsosolosa matla | 0~200% | E itšetlehileng ka mohlala | ☆ |
| Sehlopha sa P3: V / F Control Parameters | ||||
|
P3-00 |
V/F curve setting |
0: Mohala o otlolohileng V/F 1: multipoint V/F 2: square V/F 3: 1.2 Matla V/F 4: 1.4 Matla V/F 6: 1.6 Matla a V/F 8: 1.8 matla V/F 9: A bolokiloe 10: VF e feletseng ea karohano mokhoa 11: VF semi-separation mode |
0 |
★ |
| P3-01 | Matlafatso ea torque | 0.0%: (Ha e sebetse) 0.1%~30.0% | E itšetlehileng ka mohlala | |
| P3-02 | Ho fokotseha ha maqhubu a torque e matlafatsang | 0.00Hz ~ boholo. makhetlo a mangata | 50.00Hz | ★ |
| P3-03 | Multi-point V/F frequency1 | 0.00Hz~P3-05 | 0.00Hz | ★ |
| P3-04 | Multi-point V/F voltage 1 | 0.0%~100.0% | 0.0% | ★ |
| P3-05 | Multi-point V/F frequency 2 | P3-03~P3-07 | 0.00Hz | ★ |
| P3-06 | Multi-point V/F voltage 2 | 0.0%~100.0% | 0.0% | ★ |
| P3-07 | Multi-point V/F frequency 3 | P3-05 ~ rated motor frequency (P1-04) | 0.00Hz | ★ |
| P3-08 | Multi-point V/F voltage 3 | 0.0%~100.0% | 0.0% | ★ |
| P3-09 | Phaello ea matšeliso a thellang | – | – | – |
| P3-10 | Katleho e feteletseng ea V/F | 0-200 | 64 | ☆ |
| P3-11 | Phaello ea khatello ea V / F oscillation | 0-100 | 40 | ☆ |
|
P3-13 |
Moqtage mohloli oa karohano ea V / F |
0: boemo ba dijithale (P3-14) 1: AI1 (Hlokomela: J6 jumper) 2: AI2 3: AI3
4: Boemo ba ho kenya letsoho ka lebelo le phahameng (S5) 5: litaelo tsa likarolo tse ngata 6: PLC e bonolo ea 7: PID 8: puisano e fanoeng Tlhokomeliso: 100.0% e lumellana le motlakase e lekantsoeng voltage |
0 |
☆ |
| P3-14 | Digital setting of voltage bakeng sa karohano ea V/F | 0V ~ rated motor voltage | 0V | ☆ |
| P3-15 | Moqtage tsoha nako ea V/F karohano | 0.0s ~ bo1000.0
Tlhokomeliso: 0V ho rated motor voltage |
0.0s | ☆ |
| P3-16 | Moqtage fokotseha nako ea V/F karohano | 0.0s ~ bo1000.0
Tlhokomeliso: nako ea 0V ho rated motor voltage |
0.0s | ☆ |
| P3-17 | Khetho ea mokhoa oa ho emisa bakeng sa karohano ea V/F | 0: Khafetsa le voltage ho theoha ho 0 ka boikemelo 1: Ho fokotseha ha makhetlo ka mor'a voltage fokotseha ho 0 | 0 | ☆ |
| P3-18 | Boemo ba hona joale ba moeli | 50~200% | 150% | ★ |
| P3-19 | Khetho ea hona joale ea moeli | 0: ha e na thuso 1: e na le thuso | 1 | ★ |
| P3-20 | Moeli oa hona joale oa phaello | 0-100 | 20 | ☆ |
| P3-21 | Matšeliso a lebaka la lebelo le atisang moeli oa boemo ba hajoale | 50~200% | 50% | ★ |
| P3-22 | Moqtagmoeli | 650V ~ 800.0V | 770V | ★ |
| P3-23 | Moqtagkhetho ea moeli | 0: ha e na thuso 1: e na le thuso | 1 | ★ |
| P3-24 | Khafetsa phaello bakeng sa voltagmoeli | 0-100 | 30 | ☆ |
| P3-25 | Moqtage fumana bakeng sa voltagmoeli | 0-100 | 30 | ☆ |
| P3-26 | Maqhubu a ho phahama ha sekhahla nakong ea voltagmoeli | 0-50Hz | 5Hz | ★ |
| Sehlopha sa P4: Li-terminals tsa ho kenya | ||||
|
P4-00 |
Khetho ea ts'ebetso ea S1 |
0: ha ho na ts'ebetso ea 1: Forward run (FWD) kapa tsamaisa taelo ea 2: reverse run (REV) kapa tataiso e nepahetseng le e mpe (Hlokomela: beha 1, 2 e tla sebelisoa le P4-11)
3:taolo ea ts'ebetso ea lithapo tse tharo 4: jog e eang pele (FJOG) 5: reverse jog (RJOG) 6: Terminal UP 7: Terminal TLAS'A 8: sebaka sa ho paka mahala 9: Phoso ea botjha (RESET) 10: matha khefutsa 11: Phoso ea kantle e atisa ho buleha kenya letsoho 12:Boemo ba litaelo tsa mehato e mengata 1 13:Boemo ba litaelo tsa mehato e mengata 2 14:Boemo ba litaelo tsa mehato e mengata 3 15:Teminale ea litaelo tse ngata 4 16: Theminale ea ho potlakisa/Ho theola lebelo la khetho ea nako 1 17:Boemo ba ho khetha nako ea ho potlakisa/ho fokotsa lebelo 2 18: Ho fetola taelo ea khafetsa 19: UP / TLASE ho beha ho hlakile (terminal, keyboard) 20: taelo ea taolo ea ho fetola terminal 1 21: Ho potlakisa / ho fokotsa lebelo ho thibetsoe 22: PID khefutsa 23: Easy PLC boemo bo tsosolositsoeng 24: Wobble e emisitsoe 25: Counter input 26: Counter reset 27: Kenyeletso ya palo ya bolelele 28: Seta botjha bo bolelele 29: Taolo ya torque e holotswe 30: Kenyelletso ea lebelo le phahameng (e sebetsang feela bakeng sa S5) 31: E bolokiloe 32: Haufinyane DC Braking 33: Phoso ea ka ntle e tloaelehileng e koetsoe 34: Phetoho ea maqhubu e nolofalitsoe 35: Tataiso ea PID e khutlisetsoa morao 36: Boemelo ba ho paka ka ntle 1 37:taelo ea ho chencha terminal 2 38: PID integral e emisitsoe 39: Mohloli oa maqhubu A le ho fetola maqhubu a seng a setiloe 40: Mohloli oa maqhubu a B le ho fetola maqhubu a seng a setiloe 41: Ts'ebetso ea khetho ea likoloi 42: E bolokiloe 43: PID parameter switch 44: Mosebelisi o hlalositse phoso 1 45: phoso e hlalositsoeng ke mosebelisi 2 46: Taolo ea lebelo / taolo ea torque 47: Emergency stop 48: Sebaka sa ho paka ka ntle 2 49:Ho theola lebelo la braking ea DC 50: Nako ena ea ho matha e hlakotsoe 51: switch ea lithapo tse peli / tse tharo 52: Reverse frequency e holofetse 53-59: E bolokiloe |
1 |
★ |
|
P4-01 |
Khetho ea ts'ebetso ea S2 |
4 |
★ |
|
|
P4-02 |
Khetho ea ts'ebetso ea S3 |
9 |
★ |
|
|
P4-03 |
Khetho ea ts'ebetso ea S4 |
12 |
★ |
|
|
P4-04 |
Khetho ea ts'ebetso ea S5 |
13 |
★ |
|
|
P4-05 |
Khetho ea ts'ebetso ea S6 |
0 |
★ |
|
|
P4-06 |
Khetho ea ts'ebetso ea S7 |
0 |
★ |
|
|
P4-07 |
Khetho ea ts'ebetso ea S8 |
– |
★ |
|
|
P4-08 |
Reserved |
– |
★ |
|
|
P4-09 |
Reserved |
– |
★ |
|
| P4-10 | S1~S4 nako ea ho sefa | 0.000s ~ bo1.000 | 0.010s | ☆ |
| P4-11 | Mokhoa oa ho laola terminal | 0: mela e 'meli 1 1: mela e 'meli 2 2: mela e meraro 1 3: mela e meraro 2 | – | ★ |
| P4-12 | Seteishene UP/DOWN N sekhahla | 0.001Hz/s~65.535Hz/s | 1.00Hz/s | ☆ |
| P4-13 | AI curve 1 min. kenya letsoho | 0.00V~P4-15 | 0.00V | ☆ |
| P4-14 | Liphesente tse tsamaellanangtage ea AI curve 1 min. kenya letsoho | - 100.0%~+100.0% | 0.0% | ☆ |
| P4-15 | AI curve 1 max. kenya letsoho | P4-13~+10.00V | 10.00V | ☆ |
| P4-16 | Liphesente tse tsamaellanangtage ea AI curve 1 max. kenya letsoho | - 100.0%~+100.0% | 100.0% | ☆ |
| P4-17 | AI1 nako ea ho sefa | 0.00s ~ bo10.00 | 0.10s | ☆ |
| P4-18 | AI curve 2 min. kenya letsoho | 0.00V~P4-20 | 0.00V | ☆ |
| P4-19 | Liphesente tse tsamaellanangtage ea AI curve 2 min. kenya letsoho | - 100.0%~+100.0% | 0.0% | ☆ |
| P4-20 | AI curve 2 max. kenya letsoho | P4-18~+10.00V | 10.00V | ☆ |
| P4-21 | Liphesente tse tsamaellanangtage ea AI curve 2 max. kenya letsoho | - 100.0%~+100.0% | 100.0% | ☆ |
| P4-22 | AI2 nako ea ho sefa | 0.00s ~ bo10.00 | 0.10s | ☆ |
| P4-23 | AI3 curve min. kenya letsoho | – 10.00V~P4-25 | - 10.0V | ☆ |
| P4-24 | Liphesente tse tsamaellanangtage ea AI curve 3 min. kenya letsoho | - 100.0%~+100.0% | - 100.0% | ☆ |
| P4-25 | AI curve 3 max. kenya letsoho | P4-23~+10.00V | 10.00V | ☆ |
| P4-26 | Liphesente tse tsamaellanangtage ea AI curve 3 max. kenya letsoho | - 100.0%~+100.0% | 100.0% | ☆ |
| P4-27 | AI3 nako ea ho sefa | 0.00s ~ bo10.00 | 0.10s | ☆ |
| P4-28 | Pulse min. kenya letsoho | 0.00kHz~P4-30 | 0.00KHz | ☆ |
| P4-29 | Liphesente tse tsamaellanangtage ea pulse min. kenya letsoho | - 100.0% ~ 100.0% | 0.0% | ☆ |
| P4-30 | Pulse max. kenya letsoho | P4-28 ~ 100.00kHz | 50.00KHz | ☆ |
| P4-31 | Liphesente tse tsamaellanangtagE of pulse max. kenya letsoho | - 100.0% ~ 100.0% | 100.0% | ☆ |
| P4-32 | Nako ea sesefa sa Pulse | 0.00s ~ bo10.00 | 0.10s | ☆ |
|
P4-33 |
Khetho ea li-curve tsa AI |
Bit: AI1 khetho ea curve 1: curve 1 (2 lintlha, bona P4-13~P4-16) 2: Curve 2 (2 lintlha, bona P4-18~P4-21) 3: curve 3 (2 lintlha, bona P4- 23~P4-26) 4: curve 4 (4 lintlha, bona A6-00~A6-07) 5: curve 5 (4 lintlha, bona A6-08~A6-15) Leshome: AI2 khetho ea curve, ibid Hundreds:AI3 khetho ea curve, ibid |
321 |
☆ |
|
P4-34 |
Ho khetha khetho ha AI e ka tlase ho min. kenya letsoho |
Bit: AI1 e tlase ho feta bonyane ba ho kenya 0: e lumellana le bonyane ba ho kenya 1: 0.0% Leshome: AI2 e tlase ho feta bonyane ba ho kenya, ibid Makholo: AI3 e tlase ho feta bonyane ba ho kenya, ibid |
000 |
☆ |
| P4-35 | S1 tieho | 0.0s ~ bo3600.0 | 0.0s | ★ |
| P4-36 | S2 tieho | 0.0s ~ bo3600.0 | 0.0s | ★ |
| P4-37 | S3 tieho | 0.0s ~ bo3600.0 | 0.0s | ★ |
| P4-38 | S1~S5 khetho ea mokhoa o sebetsang 1 | 0: e sebetsang holimo 1: e sebetsang tlase Bit: S1 Leshome: S2 Libaka tse lekholo: S3 Likotoana tse likete: S4 Million: S5 | 00000 | ★ |
| Sehlopha sa P5: Li-terminals tsa Output | ||||
|
P5-02 |
Relay 1 khetho ea mosebetsi (TA-TC) |
0: pulse output (HDP) 1: Switching output (HDY) |
2 |
☆ |
| 0: Ha ho tlhahiso ea 1: Inverter e sebetsa 2: tlhahiso ea phoso (phoso ea ho emisa) 3: Ho lemoha boemo ba maqhubu a FDT1 tlhahiso ea 4: maqhubu a fihla 5: Ts'ebetso ea lebelo la Zero (ha ho na tlhahiso ha ho koaloa) 6: motor overload pre-alarm 7: Inverter overload pre-alarm 8: Beha palo ea palo ho fihla ho 9: E bolela hore palo ea palo e fihla 10: bolelele ho fihla ho 11: Potoloho ea PLC e felile 12: Nako ea ho matha e fihla 13: Moeli oa makhetlo a 14: Moeli oa torque 15: O itokiselitse ho matha 16: AI1> AI2 17: moeli o ka holimo oa ho fihla khafetsa 18: Ho fihla ha maqhubu a tlase (ho amana le ts'ebetso) 19:Undervoltage boemo ba tlhahiso ea 20: litlhophiso tsa puisano 21:Boemo bo phethiloe (bo boloketsoe) 22:maemo a koaletsoeng (e bolokiloe) 23: lebelo la zero le matha 2 (le tlhahiso ha e emisitsoe) 24: Nako eohle ea ho matlafatsa matla e fihla 25: Boemo ba makhetlo a 26: Hangata 1 E fihla tlhahiso ea 27: Frequency 2 e fihla tlhahiso ea 28: ea hajoale 1 e fihla tlhahiso 29: 2 ea hajoale e fihlella tlhahiso 30: Nako ea ho fihla ha nako
31: AI1 input ke overrun 32: Underload 33: reverse matha 34: zero boemo ba hona joale 35:Module mocheso fihla 36: Output hona joale e feta 37: Lower frequency fihla (shutdown le output) 38: Alarm output (tswela pele) 39:Motor over temoso ea mocheso 40: Nako ena ea ho matha e fihla 41: tlhahiso ea phoso (bakeng sa phoso ea mahala ea ho emisa), le ka tlase voltage ha se tlhahiso |
||||
|
P5-07 |
Khetho ea mosebetsi oa A01 |
0:Makhetlo a ho sebetsa 1:Peakanyo ea khafetsa 2:Output current 3:Output torque 4:Output power 5:Output voltage
6:Ho kenya letsoho ka lebelo le phahameng (100% e tsamaellana le 100.0khz) 7:AI1 8:AI2 9:AI3 10:bolelele 11:Boleng ba palo 12:Litlhophiso tsa puisano 13:Lebelo la koloi 14:Output current:(100% e tsamaellanang 1000.0A) 15:Output voltage(100% e Tšoanang le 1000.0V) 16: Torque ea motlakase (Boleng ba sebele, Peresentetage amana le enjene) |
0 |
☆ |
| P5-10 | A01 Zero bias coefficient | - 100.0%~+100.0% | 0.0% | ☆ |
| P5-11 | A01 phaello | – 10.00 ~+10.00 | 1.00 | ☆ |
| Sehlopha sa P6: Qala / Emisa Taolo | ||||
| P6-00 | Mokhoa oa ho qala | 0: Qalo e otlolohileng 1: Ho ts'oara enjene e bilikang 2: Qalo e thabisang pele 3: SVC e qala ka potlako | 0 | ☆ |
| P6-01 | Mokhoa oa ho ts'oara mochini o ohiang | 0: Ho tloha ho emisa khafetsa 1: Ho tloha ho 50Hz 2: Ho tloha ho max. makhetlo a mangata | 0 | ★ |
| P6-02 | Lebelo la ho ts'oara mochini o ohiang | 1-100 | 20 | ☆ |
| P6-03 | Leqhubu la ho qala | 0.00Hz ~ 10.00Hz | 0.00Hz | ☆ |
| P6-04 | Qala ho tšoara nako ea maqhubu | 0.0s ~ bo100.0 | 0.0s | ★ |
| P6-05 | DC ente braking 1 level/ boemo ba pele ho excitation | 0%~100% | 50% | ★ |
| P6-06 | DC ente braking 1 nako e sebetsang/
nako e ts'ebetsong pele ho tshusumetso |
0.0s ~ bo100.0 | 0.0s | ★ |
| P6-07 | Potlakiso/ Mokgoa wa ho thethefatsa | 0:Ho potlakisa ha mola/ho theoha 1:S-curve acceleration/ deceleration A (static)
2: S curve acceleration/ deceleration B (matla) |
0 | ★ |
| P6-08 | Karolo ea nako ea karolo ea ho qala ea S-curve | 0.0%~(100.0%-P6-09) | 30.0% | ★ |
| P6-09 | Karolo ea nako ea karolo ea ho qetela ea S-curve | 0.0%~(100.0%-P6-08) | 30.0% | ★ |
| P6-10 | Emisa mokhoa | 0: Fokotsa ho emisa 1 : Lebōpo ho emisa | 0 | ☆ |
| P6-11 | DC injection braking 2 qala maqhubu | 0.00Hz~ max.khafetsa
( P0-10 ) |
0.00Hz | ☆ |
| P6-12 | DC injection braking 2 nako ea ho lieha | 0.0s ~ bo100.0 | 0.0s | ☆ |
| P6-13 | DC ente braking 2 level | 0%~100% | 50% | ☆ |
| P6-14 | DC injection braking 2 nako e sebetsang | 0.0s ~ bo100.0 | 0.0s | ☆ |
| P6-15 | Karolelano ea tšebeliso ea braking | 0%~100% | 100% | ☆ |
| P6-18 | Ho ts'oara moeli oa motlakase oa spinning | 30%~200% | E itšetlehileng ka mohlala | ☆ |
| P6-21 | Nako ea demagnetization (e sebetsa bakeng sa SVC) | 0.00-5.00s | E itšetlehileng ka mohlala | ☆ |
| Sehlopha sa P7: Ts'ebetso ea Keypad le Pontšo ea LED | ||||
|
P7-02 |
STOP/RESET tshebetso ya senotlolo |
0: Ts'ebetso ea ho emisa konopo ea STOP/RES e sebetsa feela nakong ea ts'ebetso ea keyboard
1: STOP/RES key shutdown e sebetsa ka mokgwa ofe kapa ofe wa ts'ebetso |
1 |
☆ |
|
P7-03 |
Setšoantšo sa LED se sebetsang parameter 1 |
0000~FFFF Bit00: Nako ea ho sebetsa 1 (Hz) Bit01: Seta maqhubu (Hz) Bit02: Bus voltage (V) Bit03: Output voltage (V) Bit04: Output current (A) Bit05: Output power (kW) Bit06: Output torque (%) Bit07: S terminal input status Bit08: HDO output status Bit09: AI1 voltage (V) Bit10: AI2 Moqtage (V) Bit11: AI3 Moqtage (V) Bit12: Bala boleng Bit13: Boleng ba boleng Bit14: Pontšo ea lebelo la mojaro Bit15: Setlhophiso sa PID |
1F |
☆ |
|
P7-04 |
Setšoantšo sa LED se sebetsang parameter 2 |
0000~FFFF Bit00: Maikutlo a PID Bit01: PLC stage Bit02: High-speed pulse input frequency (kHz) Bit03: Operating frequency 2 (Hz) Bit04: Nako e setseng Bit05: AI1 pele ho ntlafatso ea vol.tage (V) Bit06: AI2 pele ho khalemelo voltage (V) Bit07: AI3 Tokiso pele ho voltage (V) Bit08: Lebelo la mola
Bit09: Nako ea hona joale ea matla (Hora) Bit10: Nako ea hona joale ea ho sebetsa (Min) Bit11: Lebelo le phahameng la lebelo la pulse (Hz) Bit12: Puisano set point Bit13: Encoderfeedback speed (Hz) Bit14: Main frequency A display (Hz) Bit15: Pontšo ea bobeli ea maqhubu a B (Hz) |
0 |
☆ |
|
P7-05 |
Li-parameter tse emisang ponts'o ea LED |
0000~FFFF
Bit00: Seta maqhubu (Hz) Bit01: Bus voltage (V) Bit02: S boemo ba ho kenya Bit03: Boemo ba tlhahiso ea HDO Bit04: AI1 voltage (V) Bit05: AI2 voltage (V) Bit06: AI3 voltage (V) Bit07: Bala boleng Bit08: Boleng ba boleng Bit09: PLC stage Bit10: Lebelo la mojaro Bit11: PID setting Bit12: High-speed pulse input frequency (kHz) |
33 |
☆ |
| P7-06 | Laola lebelo la pontsho ya coefficient | 0.0001-6.5000 | 1.0000 | ☆ |
| P7-07 | Mocheso oa Heatsink oa AC Drive IGBT | -20.0℃~ 120.0℃ | – | ● |
| P7-09 | Accumulative matha nako | 0h ~ 65535h | – | ● |
|
P7-12 |
Nomoro ea libaka tsa decimal bakeng sa pontšo ea lebelo la mojaro |
Bit: d0-14 palo ea libaka tse decimal 0: 0 libaka decimal 1: 1 decimal place 2: 2 decimal libaka 3: 3 libaka tse leshome: d0-19/d0-29 palo ea libaka decimal 1: 1 decimal place 2 : Libaka tse 2 tsa decimal |
21 |
☆ |
| P7-13 | Pokello ya matla-ka nako | 0h ~ 65535h | – | ● |
| P7-14 | Tšebeliso e matla ea matla | 0kW~65535kwh | – | ● |
| Sehlopha sa P8: Mesebetsi ea Thuso | ||||
| P8-04 | Nako ea ho phomola 2 | 0.0s ho 6500.0s | E itšetlehileng ka mohlala | ☆ |
| P8-05 | Nako ea ho potlakisa 3 | 0.0s ho 6500.0s | E itšetlehileng ka mohlala | ☆ |
| P8-06 | Nako ea ho phomola 3 | 0.0s ho 6500.0s | E itšetlehileng ka mohlala | ☆ |
| P8-07 | Nako ea ho potlakisa 4 | 0.0s ho 6500.0s | E itšetlehileng ka mohlala | ☆ |
| P8-08 | Nako ea ho phomola 4 | 0.0s ho 6500.0s | E itšetlehileng ka mohlala | ☆ |
| P8-09 | Ho tlola khafetsa 1 | 0.00Hz ho ea ho max. makhetlo a mangata | 0.00Hz | ☆ |
| P8-10 | Ho tlola khafetsa 2 | 0.00Hz ho ea ho max. makhetlo a mangata | 0.00Hz | ☆ |
| P8-11 | Sehlopha sa ho tlola khafetsa | 0.00Hz ho ea ho max. makhetlo a mangata | 0.00Hz | ☆ |
| P8-12 | Forward/Reverse run switch over the dead-zone time | 0.0s ho 3000.0s | 0.0s | ☆ |
| P8-13 | Khutlisetsa khetho ea RUN | 0: e fosahetse, 1: e sebetsa | 0 | ☆ |
| P8-14 | Mokhoa oa ho matha ha referense ea maqhubu e le tlase ho feta moeli o fokolang oa maqhubu | 0 ho ea ho 2 | 0 | ☆ |
| P8-15 | Sekhahla sa ho theoha | 0.00% ho isa ho 100.00% | 0.00% | ☆ |
| P8-16 | Pokello ea matla-ka nako ea nako | 0 ho isa ho 65000h | 0h | ☆ |
| P8-17 | Accumulative matha nako moeko | 0 ho isa ho 65000h | 0h | ☆ |
| P8-18 | Khetho ea ts'ireletso ea ho qala | 0: Ha ea lokela ho sireletsoa, 1: sireletsa | 0 | ☆ |
| P8-19 | Boleng ba ho lemoha khafetsa 1 | 0.00Hz ho ea ho max. makhetlo a mangata | 50.00Hz | ☆ |
| P8-20 | Maqhubu a ho lemoha hysteresis 1 | 0.0% ho isa ho 100.0% | 5.0% | ☆ |
| P8-21 | Bophara ba ho lemoha ha nako e reriloeng e fihletsoe | 0.0% ho isa ho 100.0% | 0.0% | ☆ |
| P8-22 | Ts'ebetso ea ho qhomela khafetsa | 0: e fosahetse, 1: e sebetsa | 0 | ☆ |
| P8-25 | Switchover frequency ea accel time 1 le accel time 2 | 0.00Hz ho ea ho max. makhetlo a mangata | 0.00Hz | ☆ |
| P8-26 | Switchover frequency ea decel time 1 le decel time 2 | 0.00Hz ho ea ho max. makhetlo a mangata | 0.00Hz | ☆ |
| P8-27 | Beha ntho e tlang pele ho ts'ebetso ea terminal ea JOG | 0: ha e sebetse , 1:e sebetsa hantle | 0 | ☆ |
| P8-28 | Boleng ba ho lemoha khafetsa 2 | 0.00Hz ho ea ho max. makhetlo a mangata | 50.00Hz | ☆ |
| P8-29 | Li-hysteries tsa ho lemoha khafetsa ke 2 | 0.0% ho isa ho 100.0% | 5.0% | ☆ |
| P8-30 | Ho fumaneha ha maqhubu 1 | 0.00Hz ho ea ho max. makhetlo a mangata | 50.00Hz | ☆ |
| P8-31 | Ho lemoha bophara ba maqhubu 1 | 0.0% ho isa ho 100.0%
(max.frequency) |
0.0% | ☆ |
| P8-32 | Ho fumaneha ha maqhubu 2 | 0.00Hz ho ea ho max. makhetlo a mangata | 50.00Hz | ☆ |
| P8-33 | Ho lemoha bophara ba maqhubu 2 | 0.0% ho isa ho 100.0% (max frequency) | 0.0% | ☆ |
| P8-34 | Boemo ba hona joale ba ho tseba | 0.0% ho isa ho 300.0% (e lekantsoe motlakase oa hajoale) | 5.0% | ☆ |
| P8-35 | Ho lieha ho fumana ha hona joale | 0.01s ho 600.00s | 0.10s | ☆ |
| P8-36 | Sephetho ho feta moeli oa hajoale | 1.1% (ha e fumanehe) 1.2% ho isa ho 300.0% (e lekanyelitsoe motlakase oa hona joale) | 200.0% | ☆ |
| P8-37 | E hlahisoa ka lebaka la tieho ea hona joale ea ho fumana | 0.00s ho 600.00s | 0.00s | ☆ |
| P8-38 | Boemo ba ho sibolloa ha hajoale 1 | 0.0% ho isa ho 300.0% (e lekantsoe motlakase oa hajoale) | 100.0% | ☆ |
| P8-39 | Bophara ba ho lemoha ha hajoale 1 | 0.0% ho isa ho 300.0% (e lekantsoe motlakase oa hajoale) | 0.0% | ☆ |
| P8-40 | Boemo ba ho sibolloa ha hajoale 2 | 0.0% ho isa ho 300.0% (e lekantsoe motlakase oa hajoale) | 100.0% | ☆ |
| P8-41 | Bophara ba ho lemoha ha hajoale 2 | 0.0% ho isa ho 300.0% (e lekantsoe motlakase oa hajoale) | 0.0% | ☆ |
| P8-42 | Mosebetsi oa nako | 0: e fosahetse 1: e sebetsa | 0.0% | ★ |
| P8-43 | Nako e sebetsang ea ho hlophisa kanale | 0 ho ea ho 3 | 0 | ★ |
| P8-44 | Nako ea ho matha | 0.0 ho isa ho 6500.0 mots | 0.0 mets | ★ |
| P8-45 | AI1 tlhahiso ea voltage tlase moeli | 0.00V ho F8-46 | 3.10V | ☆ |
| P8-46 | AI1 tlhahiso ea voltage holimo moeli | F8-45 ho 10.00V | 6.80V | ☆ |
| P8-47 | Mocheso oa mocheso oa IGBT | 0 ℃ ho isa ho 100 ℃ | 75 ℃ | ☆ |
| P8-48 | Mokhoa o pholileng oa ho sebetsa oa fan | 0: Fan e matha nakong ea ts'ebetso 1: fan e lula e matha | 0 | ☆ |
| P8-49 | Maqhubu a ho tsoha | F8-51 ho ea ho max. Hangata (F0-10) | 0.00Hz | ☆ |
| P8-50 | Nako ea ho lieha ho tsoha | 0.0s ~ bo6500.0 | 0.0s | ☆ |
| P8-51 | Hibernating frequency | 0.00Hz ho tsoha khafetsa (P8-49) | 0.00Hz | ☆ |
| P8-52 | Hibernating nako ea ho lieha | 0.0s ~ bo6500.0 | 0.0s | ☆ |
| P8-53 | Nako ea nako ea ho sebetsa nakong ena | 0.0~6500.0 mets | 0.0 mets | ☆ |
| P8-54 | Coefficient ea ho lokisa matla a tsoang | 0.0% ho isa ho 200.0% | 100.0% | ☆ |
| Sehlopha sa P9: Phoso le Tšireletso | ||||
| P9-00 | Tšireletso ea boima ba motlakase | 0: E thibetsoe 1: E lumelletsoe | 1 | ☆ |
| P9-01 | Phaello ea ts'ireletso ea boima ba 'mele | 0.20 ho ea ho 10.00 | 1.00 | ☆ |
| P9-02 | Enjene e ngata haholo coefficient pele ho temoso | 50% ho isa ho 100% | 80% | ☆ |
| P9-03 | Ho tlolatage fumana tšireletso | 0-100 | 30 | ☆ |
| P9-04 | Ho tlolatage tshireletso voltage | 650 ho 800V | 770V | ☆ |
|
P9-07 |
Ho sibolloa ha
short-circuit to ground upon power on |
Diyuniti: Khetho ea ts'ireletso ea potoloho e khuts'oane ea Power-to-ground 0: E fosahetse 1: Sebaka sa Mashome se nepahetseng: Khetho ea ts'ireletso ea nako e khuts'oane pele e matha 0: E fosahetse |
01 |
☆ |
| P9-08 | Braking unit e sebelisitsoeng voltage | 650 ho 800V | 720V | ☆ |
| P9-09 | Linako tsa ho seta bocha | 0 ho ea ho 20 | 0 | ☆ | |||
| P9-10 | Khetho ea ketso ea DO nakong ea ho seta bocha | 0: Ha ho ketso ea 1: Ketso | 0 | ☆ | |||
| P9-11 | Ho lieha ha auto reset | 0.1s ho 100.0s | 1.0s | ☆ | |||
| P9-12 | Input phase loss/ Tshireletso ya relay pele ho tefo | Nomoro ea yuniti: khetho ea tšireletso ea tahlehelo ea karolo ea ho kenya Sebaka sa leshome: Khetho ea tšireletso ea ho ikopanya kapa ea ho hula 0: E thibetsoe 1: E lumelloe |
– |
– | |||
|
P9-13 |
Tšireletso ea tahlehelo ea mohato oa tlhahiso |
Linomoro tsa yuniti: khetho ea ts'ireletso ea tahlehelo ea karolo ea tlhahiso 0: E thibetsoe 1: E lumelletsoe Sebaka sa Mashome: khetho ea ts'ireletso ea tahlehelo ea karolo ea tlhahiso pele e sebetsa
0: E thibetsoe 1: E lumelletsoe |
01 |
☆ |
|||
| P9-14 | Mofuta oa 1 oa phoso |
00-55 |
– | ● | |||
| P9-15 | Mofuta oa 2 oa phoso | – | ● | ||||
| P9-16 | Mofuta oa 3 (oa morao-rao) oa phoso | – | ● | ||||
| P9-17 | Khafetsa holim'a phoso ea 3 | – | – | ● | |||
| P9-18 | Hajoale holim'a phoso ea 3 | – | – | ● | |||
| P9-19 | Bese voltage holim'a phoso ea 3 | – | – | ● | |||
| P9-20 | Boemo ba DI holim'a phoso ea 3 | – | – | ● | |||
| P9-21 | Etsa qeto holim'a phoso ea 3 | – | – | ● | |||
| P9-22 | Boemo ba koloi ea AC holim'a phoso ea 3 | – | – | ● | |||
| P9-23 | Nako ea ho sebetsa holim'a phoso ea 3 | – | – | ● | |||
| P9-24 | Nako ea ho matha holim'a phoso ea 3 | – | – | ● | |||
| P9-27 | Khafetsa holim'a phoso ea 2nd | – | – | ● | |||
| P9-28 | Hajoale holim'a phoso ea 2 | – | – | ● | |||
| P9-29 | Bese voltage holim'a phoso ea bobeli | – | – | ● | |||
| P9-30 | DI bolela hodima phoso ya bobedi | – | – | ● | |||
| P9-31 | ETSA boemo holim'a phoso ea bobeli | – | – | ● | |||
| P9-32 | Boemo ba koloi ea AC holim'a phoso ea 2nd | – | – | ● | |||
| P9-33 | Nako ea ho sebetsa holim'a phoso ea 2nd | – | – | ● | |||
| P9-34 | Nako ea ho matha holim'a phoso ea 2nd | – | – | ● | |||
| P9-37 | Hangata ka lebaka la phoso ea pele | – | – | ● | |||
| P9-38 | Hajoale ka phoso ea pele | – | – | ● | |||
| P9-39 | Bese voltage holim'a phoso ea pele | – | – | ● | |||
| P9-40 | DI bolela hodima phoso ya pele | – | – | ● | |||
| P9-41 | ETSA ka lebaka la phoso ea pele | – | – | ● | |||
| P9-42 | Boemo ba ho khanna ba AC holim'a phoso ea 1 | – | – | ● | |||
| P9-43 | Nako ea ho sebetsa holim'a phoso ea 1 | – | – | ● | |||
| P9-44 | Nako ea ho matha holim'a phoso ea 1 | – | – | ● | |||
| P9-47 | Khetho ea ts'ireletso ea liphoso 1 | 0:mahala 1: emisa 2.tsoela pele ho matha | 00000 | ☆ | |||
| P9-48 | Khetho ea ts'ireletso ea liphoso 2 | 00000 ho ea ho 11111 | 00000 | ☆ | |||
| P9-49 | Khetho ea ts'ireletso ea liphoso 3 | 00000 ho ea ho 22222 | 00000 | ☆ | |||
| P9-50 | Khetho ea ts'ireletso ea liphoso 4 | 00000 ho ea ho 22222 | 00000 | ☆ | |||
| P9-54 | Khetho ea makhetlo bakeng sa ho tsoela pele ho sebetsa ka phoso | 0 ho ea ho 4 | 0 | ☆ | |||
| P9-55 | Backup frequency holim'a phoso | 0.0% ho isa ho 100.0% (max. FrequencyP0-10) | 100.0% | ☆ | |||
| P9-56 | Mofuta oa sensor ea mocheso oa motlakase | 0: Ha ho na sensor ea mocheso 1: Pt100 2: PT1000 | – | – | |||
| P9-59 | Khetho ea ts'ebetso ea ho qoela ka matla | 0: E fosahetse 1: leqhubu la libesetage control 2: deceleration stop | 0 | ☆ | |||
| P9-60 | Monyetla oa ho tsamaea ha matla ka har'a ts'ebetso o koetsoe | 80% ho isa ho 100% | 85% | ☆ | |||
| P9-62 | Monyetla oa ho qoelisoa ha matla ka ts'ebetso o lumelletsoe | 60% ho isa ho 100% | 80% | ☆ | |||
| P9-63 | Laela tshireletso e lahlehileng | 0: E holofalitsoe 1: E lumelletsoe | 0 | ☆ | |||
| P9-64 | Fumana boemo bo lahlehileng | 0.0% ho isa ho 100.0% | 10.0% | ☆ | |||
| P9-65 | Kenya nako ea ho tseba e lahlehileng | 0.0s ho 60.0s | 1.0s | ☆ | |||
| P9-67 | Boemo ba ho lemoha bo fetang lebelo | 0.0% ho isa ho 50.0%( max.frequency) | 20.0% | ☆ | |||
| P9-68 | Nako ea ho lemoha e fetang lebelo | 0.0s ho 60.0s | 1.0s | ☆ | |||
| P9-69 | Boemo ba ho lemoha phoso ea lebelo | 0.0% ho isa ho 50.0%( max.frequency) | 20.0% | ☆ | |||
| P9-70 | Nako ea ho lemoha phoso ea Lebelo | 0.0s ho 60.0s | 5.0s | ☆ | |||
| P9-71 | Kp | 0 ho ea ho 100 | 40 | ☆ | |||
| P9-72 | Power dip palama-ka har'a coefficient ea bohlokoa | 0 ho ea ho 100 | 30 | ☆ | |||
| P9-73 | Nako ea ho theola boima ba 'mele ea ho theoha ha motlakase | 0.0s ho 300.0s | 20.0s | ★ | |||
| Sehlopha sa PA: Mosebetsi oa PID | |||||||
|
PA-00 |
Seteishene sa litšupiso tsa PID |
0: PA-01 setting 1: AI1 (Hlokomela: J6 jumper) 2: AI2 3: AI3
4: Boemo ba ho kenya letsoho ka lebelo le phahameng (S5) 5: Puisano e fanoe 6: Ho fanoe ka litaelo tse nang le likarolo tse ngata |
0 |
☆ |
|||
| PA-01 | Litlhophiso tsa dijithale tsa PID | 0.0v% ho isa ho 100.0% | 50.0% | ☆ | |||
|
PA-02 |
Maikutlo a PID |
0: AI1 (Hlokomela: J6 jumper) 1: AI2 2: AI3 3: AI1-AI2
4: Boemo ba ho kenya letsoho ka lebelo le phahameng (S5) 5: Puisano e fanoeng 6: AI1 + AI2 7: MAX (| AI1 |, | AI2 |) 8: MIN (| AI1 |, | AI2 |) |
0 |
☆ |
|||
| PA-03 | Tataiso ea ts'ebetso ea PID | 0: Ketso e ntle 1: karabelo | 0 | ☆ | |||
| PA-04 | Tlhaloso ea PID le mefuta ea maikutlo | 0 ho ea ho 65535 | 1000 | ☆ | |||
| PA-05 | Phaello e lekanang Kp1 | 0.0 ho ea ho 1000.0 | 20.0 | ☆ | |||
| PA-06 | Nako ea bohlokoa Ti1 | 0.01s ho 10.00s | 2.00s | ☆ | |||
| PA-07 | Nako e fapaneng Td1 | 0.000s ho 10.000s | 0.000s | ☆ | |||
| PA-08 | Moeli oa tlhahiso ea PID ka lehlakoreng le ka morao | 0.00 Hz ho ea ho max. Khafetsa P0-10 | 0.00Hz | ☆ | |||
| PA-09 | Moeli oa phoso ea PID | 0.0% ho isa ho 100.0% | 0.0% | ☆ | |||
| PA-10 | Meeli e fapaneng ea PID | 0.00% ho isa ho 100.00% | 0.10% | ☆ | |||
| PA-11 | Phetoho ea nako ea PID | 0.00s ho 650.00s | 0.00s | ☆ | |||
| PA-12 | Nako ea filthara ea maikutlo a PID | 0.00s ho 60.00s | 0.00s | ☆ | |||
| PA-13 | Nako ea sefahla sa PID | 0.00s ho 60.00s | 0.00s | ☆ | |||
| PA-14 | Reserved | – | – | – | |||
| PA-15 | Phaello e lekanang Kp2 | 0.0 ho ea ho 1000.0 | 20.0 | ☆ | |||
| PA-16 | Nako ea bohlokoa Ti2 | 0.01s ho 10.00s | 2.00s | ☆ | |||
| PA-17 | Nako e fapaneng Td2 | 0.000s ho 10.000s | 0.000s | ☆ | |||
| PA-18 | PID parameter e fetola boemo | 0 ho ea ho 3 | 0 | ☆ | |||
| PA-19 | Phoso ea 1 ea PID bakeng sa phetoho ea auto | 0.0% ho PA-20 | 20.0% | ☆ | |||
| PA-20 | Phoso ea 2 ea PID bakeng sa phetoho ea auto | PA-19 ho isa ho 100.0% | 80.0% | ☆ | |||
| PA-21 | Phaello ea pele ea PID | 0.0% ho isa ho 100.0% | 0.0% | ☆ | |||
| PA-22 | Nako ea ho qala ea PID e sebetsang | 0.00s ho 650.00s | 0.00s | ☆ | |||
| PA-23 | Liphetoho tse peli tsa tlhahiso ho ea pele ho boholo | 0.0% ho isa ho 100.0% | 1.00% | ☆ |
| PA-24 | Liphetoho tse peli tsa liphetho li khutlisa boholo | 0.0% ho isa ho 100.0% | 1.00% | ☆ |
| PA-25 | Thepa ea bohlokoa ea PID | 00 ho ea ho 11 | 00 | ☆ |
| PA-26 | Boemo ba ho lemoha ha tahlehelo ea maikutlo a PID | 0.0%: Ha ho fumanoe 0.1% ho 100.0% | 0.0% | ☆ |
| PA-27 | Nako ea ho fumana tahlehelo ea maikutlo a PID | 0.0s ho 20.0s | 0.0s | ☆ |
| PA-28 | Khetho ea ts'ebetso ea PID ha u emisa | 0: Emisa ho se sebetse, 1: Ts'ebetso ea nako e tlase | 0 | ☆ |
| Sehlopha sa Pb: Mosebetsi oa Wobble, Bolelele bo Tsitsitseng le Palo | ||||
| Pb-00 | Wobble setting mode | 0: 0: e amanang le maqhubu a bohareng, 1: e amanang le maqhubu a mangata | 0 | ☆ |
| Pb-01 | Qhekella amptsebo | 0.0% ho isa ho 100.0% | 0.0% | ☆ |
| Pb-02 | Mohato o sisinyehang | 0.0% ho isa ho 50.0% | 0.0% | ☆ |
| Pb-03 | Wobble potoloho | 0.1s ho 3000.0s | 10.0s | ☆ |
| Pb-04 | Coefficient ea nako e nyolohang ea maqhubu a kgutlotharo | 0.1% ho isa ho 100.0% | 50.0% | ☆ |
| Pb-05 | Beha bolelele | 0 ho isa ho 65535m | 1000m | ☆ |
| Pb-06 | Bolelele ba 'nete | 0 ho isa ho 65535m | 0m | ☆ |
| Pb-07 | Palo ea likhahla ka mithara | 0.1 ~ 6553.5 | 100.0 | ☆ |
| Pb-08 | Beha palo ea palo | 1 ~ 65535 | 1000 | ☆ |
| Pb-09 | Hlalosa boleng ba palo | 1 ~ 65535 | 1000 | ☆ |
| Sehlopha sa PC: Litšupiso tse ngata le Mosebetsi o Bonolo oa PLC | ||||
| PC-07 | Setšoantšo sa 7 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-08 | Setšoantšo sa 8 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-09 | Setšoantšo sa 9 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-10 | Setšoantšo sa 10 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-11 | Setšoantšo sa 11 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-12 | Setšoantšo sa 12 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-13 | Setšoantšo sa 13 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-14 | Setšoantšo sa 14 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-15 | Setšoantšo sa 15 | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| PC-16 | Mokhoa o bonolo oa ho sebetsa oa PLC | 0: Ema qetellong ea lebelo le le leng 1: Boloka boleng ba ho qetela qetellong ea lebelo le le leng la 2: tsoela pele ho potoloha | 0 | ☆ |
|
PC-17 |
Khetho e bonolo ea ho boloka PLC |
Nomoro e le 'ngoe: khetho ea memori ea ho theola matla 0: Ha ho na mohopolo ha motlakase o tima 1: memori ea ho theola sebaka sa leshome: Khetho ea memori ea ho emisa 0: Emisa mohopolo 1: memori e koalang |
00 |
☆ |
| PC-18 | Nako ea ho sebetsa ea referense e bonolo ea PLC 0 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-19 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 0 | 0 ho ea ho 3 | 0 | ☆ |
| PC-20 | Nako ea ho sebetsa ea referense e bonolo ea PLC 1 | 0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-21 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 1 | 0 ho ea ho 3 | 0 | ☆ |
| PC-22 | Nako ea ho sebetsa ea referense e bonolo ea PLC 2 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-23 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 2 | 0 ho ea ho 3 | 0 | ☆ |
| PC-24 | Nako ea ho sebetsa ea referense e bonolo ea PLC 3 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-25 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 3 | 0 ho ea ho 3 | 0 | ☆ |
| PC-26 | Nako ea ho sebetsa ea referense e bonolo ea PLC 4 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-27 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 4 | 0 ho ea ho 3 | 0 | ☆ |
| PC-28 | Nako ea ho sebetsa ea referense e bonolo ea PLC 5 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-29 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 5 | 0 ho ea ho 3 | 0 | ☆ |
| PC-30 | Nako ea ho sebetsa ea referense e bonolo ea PLC 6 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-31 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 6 | 0 ho ea ho 3 | 0 | ☆ |
| PC-32 | Nako ea ho sebetsa ea referense e bonolo ea PLC 7 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-33 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 7 | 0 ho ea ho 3 | 0 | ☆ |
| PC-34 | Nako ea ho sebetsa ea referense e bonolo ea PLC 8 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-35 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 8 | 0 ho ea ho 3 | 0 | ☆ |
| PC-36 | Nako ea ho sebetsa ea referense e bonolo ea PLC 9 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-37 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 9 | 0 ho ea ho 3 | 0 | ☆ |
| PC-38 | Nako ea ho sebetsa ea referense e bonolo ea PLC 10 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-39 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 10 | 0 ho ea ho 3 | 0 | ☆ |
| PC-40 | Nako ea ho sebetsa ea referense e bonolo ea PLC 11 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-41 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 11 | 0 ho ea ho 3 | 0 | ☆ |
| PC-42 | Nako ea ho sebetsa ea referense e bonolo ea PLC 12 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-43 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 12 | 0 ho ea ho 3 | 0 | ☆ |
| PC-44 | Nako ea ho sebetsa ea referense e bonolo ea PLC 13 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-45 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 13 | 0 ho ea ho 3 | 0 | ☆ |
| PC-46 | Nako ea ho sebetsa ea referense e bonolo ea PLC 14 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-47 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 14 | 0 ho ea ho 3 | 0 | ☆ |
| PC-48 | Nako ea ho sebetsa ea referense e bonolo ea PLC 15 | 0.0s (h) ho isa ho 6500.0s (h) | 0.0s (h) | ☆ |
| PC-49 | Ho potlakisa / ho theola nako ea referense e bonolo ea PLC 15 | 0 ho ea ho 3 | 0 | ☆ |
| PC-50 | Nako ea nako ea PLC e bonolo e sebetsang | 0:s, 1:h | 0 | ☆ |
|
PC-51 |
Reference 0 mohloli |
0: Khoutu ea tšebetso PC-00 e fuoa 1: AI1 2: AI2 3: AI3
4: Kenyelletso ea lebelo le phahameng la 5: PID 6: Nako e behiloeng esale pele (P0-08) e fanoeng, UP / TLASE e ka fetoloa |
0 |
☆ |
| Sehlopha sa Pd: Puisano | ||||
|
Pd-00 |
Sekhahla sa Baud |
Bit: MODBUS 0: 300BPS 1: 600BPS 2: 1200BPS 3: 2400BPS 4: 4800BPS
5: 9600BPS 6: 19200BPS 7: 38400BPS 8: 57600BP 9: 115200BPS Leshome: boloka Lekholo: beetsoeng |
005 |
☆ |
| Pd-01 | Letšoao la sebopeho sa data | 0: ha ho tekano (8-N-2) 1: Esita le ho hlahloba (8-E-1) 2: Odd parity (8-O-1) 3: Ha ho tekano ( 8-N-1) | 0 | ☆ |
| Pd-02 | Aterese ea lehae | 0: Aterese ea phatlalatso; 1 ho 247 | 1 | ☆ |
| Pd-03 | Ho lieha ho arabela | 0 ho isa ho 20 ms | 2 | ☆ |
| Pd-04 | Nako ea puisano e felile | 1.1: 1.2:s ho isa ho 60.0s e fosahetseng | 0.0 | ☆ |
| Pd-05 | Khetho ea protocol ea Modbus le moralo oa data oa PROFIBUS-DP | Nyenyane: MODBUS
0: protocol e sa tloaelehang ea MODBUS 1: protocol e tloaelehileng ea MODBUS |
30 | ☆ |
| Pd-06 | Qeto ea hajoale e baloa ke puisano | 0: 0.01
1: 0.1 |
0 | ☆ |
| Sehlopha sa PE: Li-Parameters tse hlalositsoeng ke basebelisi | ||||
| PE-00 | Paramethara e hlalositsoeng ke mosebelisi 0 |
P0-00 ~ PP-xx A0-00 ~ Ax-xx d0-00 ~ d0-xx d3-00 ~ d3-xx |
d3-17 | ☆ |
| PE-01 | Paramete e hlalositsoeng ke mosebelisi1 | d3-18 | ☆ | |
| PE-02 | Paramethara e hlalositsoeng ke mosebelisi 2 | P0.00 | ☆ | |
| ………… | ……. | P0.00 | ☆ | |
| PE-29 | Paramethara e hlalositsoeng ke mosebelisi 29 | P0.00 | ☆ | |
| Sehlopha sa PP: Tsamaiso ea Parameter ea Mosebetsi | ||||
| PP-00 | Senotlolo sa mosebelisi | 0 ho ea ho 65535 | 0 | ☆ |
|
PP-01 |
Ho qala parameter |
0: Ha ho ts'ebetso ea 1: Khutlisa fektheri 0: Ha ho ts'ebetso
1: Khutlisa liparamente tsa feme ntle le paramente ea 2: Hlakola lirekoto 4: Boloka liparamente tsa hajoale tsa mosebelisi 501: Khutlisa paramethara ea "backup" |
0 |
☆ |
|
PP-02 |
Paramethara e bonts'a thepa |
Bit: d khetho ea pontšo ea sehlopha 0: ha e bontšoe 1: ponts'o Leshome: Sehlopha sa A se bonts'a khetho 0: ha se bontšoe 1: ponts'o |
11 |
★ |
|
PP-03 |
Khetho ea ponts'o ea parameter e ikhethileng |
Bit: khetho ea pontšo ea sehlopha sa mosebelisi
0: ha e bontšoe 1: bonts'a Leshome: Khetho ea Phetoho ea Basebelisi Sehlopha sa Pontšo 0: ha e bontšoe 1: ponts'o |
00 |
☆ |
| PP-04 | Khetho ea ho fetola parameter | 0: e ka fetoloa 1: e ke ke ea fetoloa | 0 | ☆ |
| Sehlopha sa A0: Taolo ea Torque le Moeli | ||||
| A0-00 | Khetho ea taolo ea lebelo / Torque | 0: taolo ea lebelo 1: taolo ea torque | 0 | ★ |
|
A0-01 |
Mohloli oa litšupiso tsa torque taolong ea torque |
0: Boemo ba dijithale 1 (A0-03) 1: AI1 (Hlokomela: J6 jumper) 2: AI2
3: AI3 4: Lebelo le phahameng la pulse (S5) 5: Puisano e fanoeng 6: MIN (AI1, AI2) 7: MAX (AI1, AI2) (1-7 dikgetho Sekala se feletseng, se lumellanang le A0-03 setting ea digital) |
0 |
★ |
| A0-03 | Torque boemo ba dijithale taolong ea torque | - 200.0% ho isa ho 200.0% | 150.0% | ☆ |
| A0-05 | Tsoela pele max. maqhubu a taolong ea torque | 0.00Hz ho ea ho max Frequency:z(P0-10) | ho | 'ma x. |
| A0-06 | Reverse max. maqhubu a taolong ea torque | 0.00Hz (P0-10) | ho | 'ma x. |
| A0-07 | Nako ea ho potlakisa taolong ea torque | 0.00s ho 65000s | 0.00s | ☆ |
| A0-08 | Nako ea ho fokotseha ha taolo ea torque | 0.00s ho 65000s | 0.00s | ☆ |
|
A2-47 |
Mohloli oa moeli oa torque taolong ea lebelo |
0: A2-48 setting 1: AI1 (Hlokomela: J6 jumper) 2: AI2 3: AI3 4: Ho kenya letsoho ka lebelo le phahameng (S5) 5: puisano e fanoeng 6: MIN (AI1, AI2) 7: MAX (AI1, AI2 )
Khetho ea 1-7 e felletseng, e tsamaellanang le litlhophiso tsa dijithale tsa A2- 48 |
0 |
☆ |
| A2-48 | Litlhophiso tsa dijithale tsa moeli oa torque taolong ea lebelo | 0.0% ho isa ho 200.0% | 150.0% | ☆ |
| A2-49 | Mohloli oa moeli oa torque taolong ea lebelo (e nchafatsang) | 0: Khoutu ea tšebetso P2-10 tlhophiso ea 1: AI1 (Hlokomela: J6 jumper) | 0 | ☆ |
| Sehlopha sa A5: Tsela ea ho Laola | ||||
| A5-00 | DPWM e fetola moeli o ka holimo oa maqhubu | 5.00Hz ho ea ho max. makhetlo a mangata | 8.00Hz | ☆ |
| A5-01 | Mokhoa oa ho feto-fetoha oa PWM | 0: Asynchronous modulation, 1: Synchronous modulation | 0 | ☆ |
| A5-02 | Khetho ea mokhoa oa matšeliso ea libaka tse shoeleng | 0: Ha ho matšeliso, 1: Mokhoa oa Matšeliso 1 | 1 | ☆ |
| A5-03 | Botebo ba PWM bo sa reroang | 0 :PWM e fosahetse 1:PWM e ka khetha | 0 | ☆ |
| A5-04 | Ho feta thibelo e potlakileng ea hona joale | 0: nolofalletsa 1:ha e khonehe | 1 | ☆ |
| A5-05 | Moqtage over modulation coefficient | 100% ho isa ho 110% | 105% | ★ |
| A5-06 | Tlas'a voltagmonyako | 150 ho 420V | 350V | ☆ |
| A5-08 | Tokiso ea nako ea Dead-zone | 0.0% ho isa ho 8.0% | 0.0% | ★ |
| A5-09 | Ho feta voltagmonyako | 650 ho 820V | E itšetlehileng ka mohlala | ★ |
| Sehlopha sa A6: Sehlopha sa AI CA6: AI Curve Settingurve Setting | ||||
| A6-00 | AI curve 4 min. kenya letsoho | - 10.00V ho A6-02 | 0.00V | ☆ |
| A6-01 | Liphesente tse tsamaellanangtage ea AI curve 4 min. kenya letsoho | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| A6-02 | AI curve 4 in exion 1 input | A6-00 ho A6-04 | 3.00V | ☆ |
| A6-15 | Liphesente tse tsamaellanangtage ea AI curve 5 max. kenya letsoho | - 100.0% ho isa ho 100.0% | 30.0% | ☆ |
| A6-24 | Sebaka sa ho qhomela sa AI1 kemiso e tsamaellanang | - 100.0% ho isa ho 100.0% | 0.0% | ☆ |
| Sehlopha sa AC: Tokiso ea AIAO | ||||
| AC-00 | AI1 e lekantsoe voltage 1 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
| AC-01 | AI1 e bonts'itsoeng voltage 1 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
| AC-02 | AI1 e lekantsoe voltage 2 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
| AC-03 | AI1 e bonts'itsoeng voltage 2 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
| AC-12 | Ao1 Sepheo sa voltage1 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
| AC-13 | Ao1 e lekantsoeng voltage 1 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
| AC-14 | AO1Target voltage 2 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
| AC-15 | Ao1 e lekantsoeng voltage 2 | - 10.00 ho 10.000V | feme e lokisitsoe | ☆ |
Monitoring Parameters
| Khoutu ea Mosebetsi | Lebitso | Pontšo Range | Aterese ea Puisano |
| Sehlopha sa d0: Mekhahlelo ea ho shebella | |||
| d0-00 | Leqhubu la ho matha | 0.01Hz | 7000H |
| d0-01 | Referense referense | 0.01Hz | 7001H |
| d0-02 | Bese voltage | 0.1V | 7002H |
| d0-03 | Sephetho voltage | 1V | 7003H |
| d0-04 | Sephetho sa hajoale | 0.01A | 7004H |
| d0-05 | Matla a hlahisang | 0.1kW | 7005H |
| d0-06 | Torque ea tlhahiso | 0.1% | 7006H |
| d0-07 | S boemo ba ho kenya | 1 | 7007H |
| d0-08 | Boemo ba tlhahiso ea HDO | 1 | 7008H |
| d0-09 | AI1 voltage | 0.01V | 7009H |
| d0-10 | AI2 voltage/hona joale | 0.01V/0.01mA | 700AH |
| d0-11 | AI3 voltage | 0.01V | EA-700BH |
| d0-12 | Bala boleng | 1 | 700CH |
| d0-13 | boleng ba bolelele | 1 | 700DH |
| d0-14 | Pontšo ea lebelo la mojaro | 1 | 700EH |
| d0-15 | Tlhaloso ea PID | 1 | 700FH |
| d0-16 | Maikutlo a PID | 1 | 7010H |
| d0-17 | PLC stage | 1 | 7011H |
| d0-18 | Pulse reference | 0.01kHz | 7012H |
| d0-19 | lebelo la maikutlo | 0.01Hz | 7013H |
| d0-20 | Nako e setseng ea ho matha | 0.1Mets | 7014H |
| d0-21 | AI1 voltage pele ho khalemelo | 0.001V | 7015H |
| d0-22 | AI2 voltage (V)/ current (MA) pele ho tokiso | 0.001V/0.01mA | 7016H |
| d0-23 | AI3 voltage pele | 0.001V | 7017H |
| d0-24 | Lebelo la koloi | 1m/Mots | 7018H |
| d0-25 | Pokello ya matla-ka nako | 1Mets | 7019H |
| d0-26 | Accumulative matha nako | 0.1Mets | 701AH |
Pontšo ea Phoso
| Khoutu ea phoso | Phoso |
| FU02 | Haholo-holo nakong ea ho potlakisa |
| FU03 | Haholo-holo nakong ea ho fokotseha |
| FU04 | Ho feta hona joale ka lebelo le sa feleng |
| FU05 | Ho feta voltage nakong ea ho potlakisa |
| FU06 | Ho feta voltage nakong ea ho fokotseha |
| FU07 | Ho feta voltage ka lebelo le sa feleng |
| FU08 | Phoso ea ho hanyetsa pele ho tefiso |
| FU09 | Tlas'a voltage |
| FU10 | AC drive e tletse |
| FU11 | Keketseho ea makoloi |
| FU13 | Ho lahleheloa ke karolo ea tlhahiso |
| FU14 | ho chesa haholo |
| FU15 | Ho tsoa phoso ea morero |
| FU16 | Phoso ea puisano |
| FU17 | Kopana kapa phoso |
| Khoutu ea phoso | Phoso |
| FU18 | Ho hloleha ha hona joale ho lemoha |
| FU19 | Ho se sebetse hantle ha motlakase |
| FU20 | Phoso ea encoder |
| FU21 | EEPROM bala-ngola |
| FU23 | Potoloho e khutšoanyane ho ea fatše |
| FU26 | Accumulative matha nako |
| FU27 | Phoso e hlalositsoeng ke mosebelisi 1 |
| FU28 | Phoso e hlalositsoeng ke mosebelisi 2 |
| FU29 | Phoso ea ho fihla ha matla a bokellaneng |
| FU30 | Ho lahleheloa ke mojaro |
| FU31 | Maikutlo a PID a lahlehile nakong ea ho sebetsa |
| FU40 | Phoso ea moeli oa hona joale oa Pulse-by-pulse |
| FU41 | Phoso ea ho fetoha ha motlakase nakong ea ho sebetsa |
| Fu42 | Ho kgeloha ka lebelo le feteletseng |
| FU43 | Enjene ho feta lebelo |
Litokomane / Lisebelisoa
 |
STEPPERONLINE EV200 Series Variable Frequency Drive [pdf] Bukana ea Mosebelisi EV200-0400G-S2, EV200-0750G-S2, EV200-1500G-S2, EV200-2200G-S2, EV200-0750G-T3, EV200-1500G-T3, EV200G2200-EV3-EV200-T3700, EV3G200-5500-T 3- 200G-T200, EVXNUMX, EVXNUMX Series Variable Frequency Drive, Variable Frequency Drive, Frequency Drive |
