Akwụkwọ ntuziaka onye ọrụ STEPPERONLINE EV200 Series Variable Frequency Drive

Akwụkwọ ntuziaka onye ọrụ maka
EV200 usoro mgbanwe ugboro mbanye

ọdịnaya zoo

1 Wepụta oke

2 Eserese Wiring ọkọlọtọ

3 Nkọwa nka na ụzụ

4 Okpokoro Funcon Parameters

5 Usoro nlekota oru

6 Ngosipụta mmejọ

7 Akwụkwọ / akụrụngwa

7.1 Ntụaka

8 Ozi ndị metụtara

Wepụta oke

Voltage	Ụdị ụdị	Ike (kW)	Ntinye nha(mm)		karịa (mm)			Wụnye oghere
			A	B	W	H	D
Otu nkeji 220V	EV200-0400G-S2	0	60	129	73	143	112	Ф4.4
	EV200-0750G-S2	0
	EV200-1500G-S2	1
	EV200-2200G-S2	2
Akụkụ atọ 380V	EV200-0750G-T3	0
	EV200-1500G-T3	1
	EV200-2200G-T3	2
	EV200-3700G-T3	3	73	168	85	180	116	Ф4.4
	EV200-5500G-T3	5

Eserese Wiring ọkọlọtọ

Ntuziaka wiring

Akara njedebe	Nkọwa ọrụ
E	ọdụ ụgbọ ala
L1, L3	Jikọọ na ọkụ grid otu-phase (220Vac) AC ike ọkọnọ
L1, L2, L3	Ejikọrọ na grid AC ike nke nkeji atọ (380Vac).
U,V,W	Jikọọ moto AC nke nwere agba atọ
B1	Filter capacitor DC akụkụ voltage nti ọnụ
B2	Enwere ike ijikọ resistor DC braking ozugbo na B1

Nkọwa nka na ụzụ

Ihe	Nkọwapụta
Ugboro kachasị	Njikwa vector: 0～500Hz; Njikwa V/F: 0 ~ 500Hz
Ugboro ugboro	0.8kHz ~ 12kHz ụgbọelu nwere ike gbanwee na-akpaghị aka dị ka okpomọkụ àgwà
Mkpebi ugboro ntinye	Ntọala dijitalụ: Ntọala Analog 0.01Hz: ugboro kachasị × 0.025%
njikwa ọnọdụ	na-enweghị PG Vector (SVC), vector nzaghachi (FVC) na njikwa V/F
Malite torque	Ụdị G: 0.5Hz/150% (SVC) ;0Hz/180% (FVC) Ụdị P: 0.5Hz/100%
Oke ọsọ	1: 100 (SVC)	1: 1000 (FVC)
izi ezi njikwa ọsọ	± 0.5% (SVC)	± 0.02% (FVC)
Izi ezi njikwa Torque	± 5% (FVC)
Ibufe ikike	Ụdị G: 150% kwadoro ugbu a 60sec; 180% kwadoro ugbu a 3 sk

Okpokoro Funcon Parameters

Mgbe edobere PP-00 ka uru na-abụghị efu, ya bụ, edobere paswọọdụ protecon parameter. Na paramita funcon na onye ọrụ na-agbanwe ọnọdụ paramita, menu paramita ga-abanyerịrị paswọọdụ ziri ezi. Ọ nwere ike ịkagbu paswọọdụ protecon funcon site na izipu PP-00 dị ka 0.
Menu nhọrọ n'ụdị paramita akọwapụtara onye ọrụ anaghị echekwa okwuntughe.
Otu P na A gụnyere paramita funcon ndị bụ isi, otu d gụnyere paramita funcon nlekota. A kọwara akara ndị dị na tebụl koodu funcon dị ka ndị a:
"☆" : ọ ga-ekwe omume gbanwee paramita mgbe ụgbọala na nkwụsị ma ọ bụ na-agba ọsọ ọnọdụ;
“★”: agaghị ekwe omume;
“●”: oke bụ uru a tụrụ n'ezie na enweghị ike ịgbanwe ya.
"*" : paramita bụ "parameter ụlọ ọrụ", naanị onye nrụpụta nwere ike ịtọ ya, machibido onye ọrụ ka ọ rụọ ọrụ.

Koodu ọrụ	Aha	Ntọala nso	Ọdabara	Gbanwee
Otu P0: Ọrụ bụ isi
P0-01	Ụdị njikwa moto 1	0: Enweghị njikwa vector vector (SVC) 1: Njikwa ihe mmetụta ọsọ ọsọ (FVC) 2: njikwa V/F	2	★
P0-02	Nhọrọ isi iyi iwu	0: Ọwa ntuziaka panel ọrụ 1: Ọwa iwu njedebe 2: ọwa iwu nkwukọrịta	0	☆
P0-03	Ntọala ntụaka ugboro ugboro Nhọrọ ọwa	0: dijitalụ ntọala (preset ugboro P0-08, UP/DOWN nwere ike gbanwee, ike abụghị ebe nchekwa) 1: dijitalụ ntọala (preset ugboro P0-08, UP/DOWN nwere ike gbanwee, ike-ala ebe nchekwa 2: AI1 (Rịba ama : J4 jumper na PANEL na AI1 ejikọrọ na kiiboodu ntinye potentiometer, PORT na AI1 ejikọrọ na mpụta AI1 ntinye) 3: Ai2 4: Ai3 5: Ntinye ngwa ngwa dị elu (S5) 6: ntuziaka ọtụtụ akụkụ 7: PLC dị mfe 8: PID 9: nzikọrịta ozi enyere 10: echekwara	2	★
P0-04	Nhọrọ ntinye iwu isi iyi ugboro inyeaka	Site na P0-03 (nhọrọ ntinye ntụziaka ugboro ugboro)	0	★
P0-05	Auxiliay ugboro isi iyi B ntụaka ihe nhọrọ	0: n'ihe gbasara ugboro kachasị 1: n'ihe gbasara isi iyi ugboro A	0	☆
P0-06	Usoro inyeaka ugboro B iwu nso	0% ~ 150%	100%	☆
P0-07	Nhọrọ ụdị nchikota isi mmalite ugboro ugboro	Bit: nhọrọ ugboro ugboro 0: Isi ugboro ugboro A 1: isi na ihe inyeaka ọrụ (mmekọrịta ọrụ kpebisiri ike site na iri) 2: Isi ugboro ugboro A na ihe enyemaka ugboro B mgba ọkụ 3: Isi ugboro ugboro A na nna ukwu na ọrụ ohu na-arụpụta mgbanwe. 4: isi iyi inyeaka B na nna ukwu na ọrụ ohu rụpụtara ngbanwe iri: isi iyi ugboro ugboro na mmekọrịta inyeaka 0: isi + inyeaka 1: isi – inyeaka 2: nke kacha 3: nke kacha nta	00	☆
P0-08	Ugboro atọ atọrọ	0.00Hz~ kacha (P0-10) ugboro	50.00Hz	☆
P0-09	Ntuziaka na-agba ọsọ	0: otu uzo 1: uzo ozo	0	☆
P0-10	Ugboro mmepụta kacha	50.00Hz ~ 500.00Hz	50.00Hz	★
P0-11	Ịtọ ọwa nke ugboro elu oke	0: P0-12 ka edobere 1:AI1 (Mbama:J6jump) 2: AI2 3: AI3 4: Ntọala ụda ọsịsọ dị elu (S5) 5: nzikọrịta ozi	0	★
P0-12	Ntụaka ugboro ugboro elu oke	Oke oke P0-10 P0-14~ ugboro kacha	50.00Hz	☆
P0-13	Ntụaka ugboro ugboro n'elu oke	0.00Hz~ ugboro kacha. P0-10	0.00Hz	☆
P0-14	Ntụtụ aka ugboro dị ala	0.00Hz ~ Ugboro elu oke P0-12	0.00Hz	☆
P0-15	Ugboro ugboro	0.8KHz ~ 12.0KHz	Ụdị dabere	☆
P0-16	Ejiri ọnọdụ okpomọkụ gbanwee ugboro ole onye na-ebu ya	0: Agbanyụrụ 1: Agbanyere	1	☆
P0-17	Oge osooso 1	0.00s ~ 65000s	Ụdị dabere	☆
P0-18	Oge mbelata 1	0.00s ~ 65000s	Ụdị dabere	☆
P0-19	Ngwa ngwa ngwa/Mbelata oge nkeji	0: 1s 1: 0.1s 2: 0.01	1	★
P0-21	Ọwa ntọala ugboro ugboro maka mgbako isi na inyeaka	0.00Hz~ max. ugboro ugboro P0-10	0.00Hz	☆
P0-22	Mkpebi ntụaka ugboro ugboro	2: 0.01Hz	2	★
P0-23	Ndokwa nke ugboro ntọala dijitalụ na nkwụsị	0: echefula 1: ebe nchekwa	1	☆
P0-24	Nhọrọ otu oke moto	0: Oke moto nke mbụ 1: oke moto nke abụọ	0	★
P0-25	Osooso/ Mbelata oge ntọala ugboro	0: kacha (P0-10) 1: Tọọ ugboro 2: ugboro 100Hz	0	★
P0-26	Ugboro ala maka mgbanwe UP/DOW n'oge ịgba ọsọ	0: Gbaa ugboro 1: Tọọ ugboro	0	★
P0-27	Ejikọtara iwu ọsọ na isi ugboro ugboro Nhọrọ iwu	Bit: Ogwe ọrụ iwu Jikọọ ugboro isi nhọrọ 0: enweghị njide 1: Digital ntọala ugboro 2: AI1 (Cheta: J6 jumper) 3: AI2 4: AI3 5: High-speed pulse ntọala ntọala (S5) 6: multi-speed 7 : PLC dị mfe 8: PID 9: nkwukọrịta nyere Iri: Terminal Command Binding Frequency Source Nhọrọ narị narị: iwu nkwurịta okwu na-ejikọta ugboro ugboro nhọrọ isi iyi.	0	☆
P0-28	Usoro nzikọrịta ozi ọdụ ụgbọ mmiri Serial	0: Modbus nkwukọrịta	0	☆
Otu P1: moto 1 Parameters
P1-00	Nhọrọ ụdị moto	0: moto asynchronous nkịtị 1: moto asynchronous ugboro dị iche iche	0	★
P1-01	Enyere ike moto	0.1KW ~ 1000.0KW	Ụdị dabere	★
P1-02	Enyere moto voltage	1V~2000V	Ụdị dabere	★
P1-03	Enyere ogo moto ugbu a	0.01 ruo 655.35A (AC mbanye ike ≤ 55 KW) 0.1 ruo 6553.5A (ike mbanye AC> 55 KW)	Ụdị dabere	★
P1-04	Enyere ugboro moto	0.01Hz~ kacha. ugboro ugboro	Ụdị dabere	★
P1-05	Enyere ọsọ moto	1rpm ~ 65535rpm	Ụdị dabere	★
P1-06	Nguzogide Stator	0.001Ω ~ 65.535Ω(AC mbanye ike≤55KW) 0.0001Ω ~ 6.5535Ω(AC mbanye ike>55KW)	Ndozi akpaaka dabere	★

P1-07	Nguzogide rotor	0.001Ω ~ 65.535Ω(AC mbanye ike≤55KW) 0.0001Ω ~ 6.5535Ω(AC mbanye ike>55KW)	Ndozi akpaaka dabere	★
P1-08	Nhapu inductive reactance	0.01mH ~ 655.35mH (AC mbanye ike≤55KW) 0.001mH ~ 65.535mH (Ac mbanye ike>55KW)	Ndozi akpaaka dabere	★
P1-09	Mmeghachi omume inductive ibe	0.1mH ~ 6553.5mH (AC mbanye ike≤55KW) 0.01mH ~ 655.35mH(AC mbanye ike>55KW)	Ndozi akpaaka dabere	★
P1-10	Enweghị ibu ugbu a	0.01A ~ P1-03(AC mbanye ike≤55KW) 0.1A ~ P1-03(AC mbanye ike>55KW) 0.1A ~ P1-03(AC mbanye ike>55KW)	Ndozi akpaaka dabere	★
P1-27	Encoder pulses kwa mgbanwe	1-65535	1024	★
P1-28	Ụdị koodu	0: ABZ ntinye koodu ntinye 2: Mkpebi	0	★
P1-30	Usoro A/B nke ntinye ntinye ntinye ABZ	0: Gaba 1: Ndokwa	0	★
P1-34	Ọnụọgụ ụzọ abụọ nke onye na-edozi ihe	1-65535	1	★
P1-36	Oge nchọta mperi nbibi waya	0.0: enweghị ọrụ 0.1s ~ 10.0s	0.0s	★
P1-37	Nhọrọ usoro nlegharị anya moto	0: Enweghị ọrụ 1: Igwe anaghị agba nchara 2 akụkụ nke parampat nke mmụta onwe onye 3: igwe asynchronous na-emegharị onwe ya zuru oke XNUMX: igwe asynchronous static static zuru oke mmụta onwe ya.	0	★
Otu P2: Usoro njikwa vector
P2-00	Uru nha nha ọsọ ọsọ 1	1-100	30	☆
P2-01	Oge ngwa ngwa loop 1	0.01s ~ 10.00s	0.50s	☆
P2-02	Ugboro ngbanwe 1	0.00-P2-05	5.00Hz	☆
P2-03	Uru nha nha ọsọ ọsọ 2	1-100	20	☆
P2-04	Oge ngwa ngwa loop 2	0.01s ~ 10.00s	1.01.00s0s	☆
P2-05	Ugboro ngbanwe 2	P2-02~ kacha ugboro (P0-10)	10.00Hz	☆
P2-06	Nweta ụgwọ ọrụ SVC/FVC	50% ~ 200%	100%	☆
P2-07	SVC Speed nzaghachi nzacha oge niile	0.000s ~ 0.100s	0.015s	☆
P2-09	Nhọrọ ọwa iwu oke oke n'okpuru njikwa ọsọ	0: koodu ọrụ P2-10 ntọala 1: AI1 2: AI2 3: AI3 4: ntọala ntinye usu dị elu (S5) 5: nzikọrịta ozi enyere 6: MIN (AI1, AI2) 7: MAX (AI1, AI2) 1-7 nhọrọ zuru oke kwekọrọ na P2-10	0	☆
P2-10	Ntọala dijitalụ nke oke torque na njikwa ọsọ	0.0% ~ 200.0%	150.0%	☆
P2-11	Isi iyi oke oke na njikwa ọsọ (na steeti mmeghari)	0: koodu ọrụ P2-12 ntọala (enweghị ihe dị iche n'etiti eletriki na ike ike) 1: AI1 2: AI2 3: AI3 4: High-speed pulse input settings 5: nkwurịta okwu nyere 6: MIN (AI1, Ai2) 7: MAX ( AI1, AI2) 8: koodu ọrụ P2-12 ntọala 1-7 Ọnụ ọgụgụ zuru ezu nke nhọrọ ahụ kwekọrọ na P2-12	0	☆
P2-12	Ntọala dijitalụ nke oke torque na njikwa ọsọ (na steeti mmeghari)	0.0% ~ 200.0%	150.0%	☆
P2-13	Ntụzigharị mkpali oke uru	0-60000	2000	☆
P2-14	Mgbanwe mkpali uru	0-60000	1300	☆
P2-15	uru nha nha mgbanwe Torque	0-60000	2000	☆
P2-16	Torque mmezi uru uru	0-60000	1300	☆
P2-17	Nhọrọ nkewa ngwa ngwa	0: Agbanyụrụ 1: Agbanyere	0	☆
P2-20	Max mmepụta voltage	–	–	–
P2-21	Oke. torque ọnụọgụ nke ubi ebelatawo ebe	50 ~ 200%	100%	☆
P2-22	Nhọrọ oke ike nrụpụta	0: Agbanyụrụ 1: Agbanyere	0	☆
P2-23	Oke ike nrụpụta	0 ~ 200%	Ụdị dabere	☆
Otu P3: Ihe njikwa V/F
P3-00	Ntọala okirikiri V/F	0: Ahịrị kwụ ọtọ V/F 1: multipoint V/F 2: square V/F 3: 1.2 Ike V/F 4: 1.4 Ike V/F 6: 1.6 Ike V/F 8: 1.8 ike V/F 9: echekwara 10: VF zuru oke ụdị nkewa 11: VF ọkara nkewa mode	0	★
P3-01	Ihe nkwalite Torque	0.0%: (adịghị arụ ọrụ) 0.1% ~ 30.0%	Ụdị dabere
P3-02	Mbelata ugboro ugboro nke mbuli torque	0.00Hz~ kacha. ugboro ugboro	50.00Hz	★
P3-03	Ọtụtụ ntụpọ V/F ugboro1	0.00Hz ~ P3-05	0.00Hz	★
P3-04	Multi-point V/F voltage 1	0.0% ~ 100.0%	0.0%	★
P3-05	Ugboro V/F ọtụtụ 2	P3-03~P3-07	0.00Hz	★
P3-06	Multi-point V/F voltage 2	0.0% ~ 100.0%	0.0%	★
P3-07	Ugboro V/F ọtụtụ 3	Ugboro moto nke P3-05 (P1-04)	0.00Hz	★
P3-08	Multi-point V/F voltage 3	0.0% ~ 100.0%	0.0%	★
P3-09	Nkwụghachi ụgwọ akwụ ụgwọ	–	–	–
P3-10	V/F uru oke mkpali	0-200	64	☆
P3-11	V/F uru nkwụsị oscillation	0-100	40	☆
P3-13	Voltage isi iyi maka V/F nkewa	0: ntọala dijitalụ (P3-14) 1: AI1 (Mbatara: J6 jumper) 2: AI2 3: AI3 4: Ntọala ntinye ngwa ngwa dị elu (S5) 5: ntụziaka nke ọtụtụ akụkụ 6: PLC dị mfe 7: PID 8: nkwurịta okwu nyere Cheta: 100.0% kwekọrọ na moto. gosiri voltage	0	☆
P3-14	Ntọala dijitalụ nke voltage maka V/F nkewa	0V~ moto gbara voltage	0V	☆
P3-15	Voltage ịrị elu oge nke V/F nkewa	0.0s ~ 1000.0s Cheta na: 0V ka moto voltage	0.0s	☆
P3-16	Voltage ọdịda oge nke V/F nkewa	0.0s ~ 1000.0s Cheta na: oge nke 0V ka moto voltage	0.0s	☆
P3-17	Kwụsị nhọrọ ọnọdụ maka nkewa V/F	0: Ugboro na voltage na-agbada 0 n'adabereghị 1: ugboro ole na-agbada mgbe voltage gbadara 0	0	☆
P3-18	Ọkwa oke dị ugbu a	50 ~ 200%	150%	★
P3-19	Nhọrọ oke dị ugbu a	0: enweghị isi 1: bara uru	1	★
P3-20	Uru oke dị ugbu a	0-100	20	☆
P3-21	Ihe nkwụghachi nke ọsọ na-abawanye ọkwa oke ugbu a	50 ~ 200%	50%	★
P3-22	Voltage ịgba	650V~800.0V	770V	★

P3-23	Voltage oke nhọrọ	0: enweghị isi 1: bara uru	1	★
P3-24	Uru ugboro ugboro maka voltage ịgba	0-100	30	☆
P3-25	Voltage uru maka voltage ịgba	0-100	30	☆
P3-26	Ọnụ ụzọ ịrị elu ugboro ugboro n'oge voltage ịgba	0 ~ 50Hz	5Hz	★
Otu P4: Ọnụ ntinye
P4-00	Nhọrọ ọrụ S1	0: enweghị ọrụ 1: Na-aga n'ihu (FWD) ma ọ bụ na-agba ọsọ iwu 2: reverse run (REV) ma ọ bụ ntụziaka na-agba ọsọ dị mma na nke na-adịghị mma (Cheta: setịpụ 1, 2 ka a ga-eji P4-11) 3: njikwa ọrụ nwere waya atọ 4: jog na-aga n'ihu (FJOG) 5: reverse jog (RJOG) 6: Terminal UP 7: Terminal DOWN 8: Ebe a na-adọba ụgbọala n'efu 9: Ntọgharị mmejọ (Tụgharịa) 10: kwụsịtụ 11: Mmejọ mpụga na-emeghekarị. ntinye 12:Multi-step Command Terminal 1 13:Multi-step Command Terminal 2 14:Multi-step Command Terminal 3 15:Multi-step Command Terminal 4 16: Osooso/Ndabere oge nhọrọ ọnụ 1 17: Osooso/Ndabere oge nhọrọ ọnụ 2 18: Ịgbanwe iwu ugboro ugboro 19: UP/down settings doro anya(terminal, kiiboodu) 20: iwu njikwa ka ịgbanwee ọnụ 1 21: Acceleration/Deceleration ka amachibidoro 22: PID kwụsịtụ 23: Mfe PLC ọnọdụ nrụpụta 24: Wobble kwụsịtụrụ 25: Counter input 26: Counter reset 27: Ntinye ngụ ogologo 28: Ntọgharị ogologo 29: Agbanyụrụ njikwa ike 30: Ntinye usu na-agba ọsọ dị elu (dị naanị maka S5) 31: Echebere 32: Ngwa ngwa DC breeki 33: Mmejọ mpụga na-emechikarị ihe ntinye 34: Ngbanwe ugboro ugboro 35: A na-atụgharị ụzọ PID. 36: Ebe a na-adọba ụgbọala na mpụga 1 37:iwu njikwa ka ịgbanwee ọnụ 2 38: PID integral kwụsịrị 39: Frequency source A na preset ugboro ịgbanwe 40: Ugboro ugboro B na preset ugboro ịgbanwe 41: Ọrụ nhọrọ ọnụ moto 42: Echekwara 43: PID parameter mgba ọkụ 44: akọwara mmejọ onye ọrụ 1 45: nkọwa njirimara onye ọrụ 2 46: Njikwa ọsọ / njikwa ike ịgbanye 47: Nkwụsị mberede 48: Ebe a na-adọba ụgbọala na mpụga 2 49:Ndalata nke DC breeki 50: A na-ekpochapụ oge ịgba ọsọ a 51: waya abụọ / waya mgba ọkụ 52: Agbarụrụ ugboro ugboro 53-59: echekwara	1	★
P4-01	Nhọrọ ọrụ S2		4	★
P4-02	Nhọrọ ọrụ S3		9	★
P4-03	Nhọrọ ọrụ S4		12	★
P4-04	Nhọrọ ọrụ S5		13	★
P4-05	Nhọrọ ọrụ S6		0	★
P4-06	Nhọrọ ọrụ S7		0	★
P4-07	Nhọrọ ọrụ S8		–	★
P4-08	Echekwara		–	★
P4-09	Echekwara		–	★
P4-10	S1 ~ S4 oge nzacha	0.000s ~ 1.000s	0.010s	☆
P4-11	Ụdị njikwa njedebe	0: ahịrị abụọ 1 1: ahịrị abụọ 2 2: ahịrị atọ 1 3: ahịrị atọ 2	–	★
P4-12	Ọnụọgụ UP/DOWN N	0.001Hz/s ~ 65.535Hz/s	1.00Hz / s	☆
P4-13	Usoro AI 1 min. ntinye	0.00V~P4-15	0.00V	☆
P4-14	Pasent kwekọrọtage nke AI curve 1 min. ntinye	- 100.0% ~ + 100.0%	0.0%	☆
P4-15	AI curve 1 max. ntinye	P4-13~+10.00V	10.00V	☆
P4-16	Pasent kwekọrọtage nke AI curve 1 max. ntinye	- 100.0% ~ + 100.0%	100.0%	☆
P4-17	Oge nzacha AI1	0.00s ~ 10.00s	0.10s	☆
P4-18	Usoro AI 2 min. ntinye	0.00V~P4-20	0.00V	☆
P4-19	Pasent kwekọrọtage nke AI curve 2 min. ntinye	- 100.0% ~ + 100.0%	0.0%	☆
P4-20	AI curve 2 max. ntinye	P4-18~+10.00V	10.00V	☆
P4-21	Pasent kwekọrọtage nke AI curve 2 max. ntinye	- 100.0% ~ + 100.0%	100.0%	☆
P4-22	Oge nzacha AI2	0.00s ~ 10.00s	0.10s	☆
P4-23	AI3 okirikiri min. ntinye	- 10.00V ~ P4-25	- 10.0V	☆
P4-24	Pasent kwekọrọtage nke AI curve 3 min. ntinye	- 100.0% ~ + 100.0%	- 100.0%	☆
P4-25	AI curve 3 max. ntinye	P4-23~+10.00V	10.00V	☆
P4-26	Pasent kwekọrọtage nke AI curve 3 max. ntinye	- 100.0% ~ + 100.0%	100.0%	☆
P4-27	Oge nzacha AI3	0.00s ~ 10.00s	0.10s	☆
P4-28	Pulse min. ntinye	0.00kHz ~ P4-30	0.00 kHz	☆
P4-29	Pasent kwekọrọtage nke pulse min. ntinye	- 100.0% ~ 100.0%	0.0%	☆
P4-30	Pulse max. ntinye	P4-28 ~ 100.00kHz	50.00 kHz	☆
P4-31	Pasent kwekọrọtage nke pulse max. ntinye	- 100.0% ~ 100.0%	100.0%	☆
P4-32	Oge nzacha usu	0.00s ~ 10.00s	0.10s	☆
P4-33	Nhọrọ okirikiri AI	Bit: AI1 curve nhọrọ 1: mgbanaka 1 (2 isi, lee P4-13~P4-16) 2: Mpịakọta 2 (2 isi, lee P4-18~P4-21) 3: akụkụ 3 (2 isi, lee P4-). 23~P4-26) 4: uzo 4 (isi 4, lee A6-00~A6-07) 5: uzo 5 (isi 4, lee A6-08~A6-15) Iri: Nhọrọ uzo AI2, ibid narị otu narị:AI3 nhọrọ okirikiri, ibid	321	☆
P4-34	Ịtọ ntọala mgbe AI na-erughị nkeji. ntinye	Bit: AI1 dị ala karịa ntọala ntinye kacha nta 0: kwekọrọ na ntọala ntinye kacha nta 1: 0.0% Iri: AI2 dị ala karịa ntọala ntinye kacha nta, ibid narị otu narị: AI3 dị ala karịa ntọala ntinye kacha nta, ibid	000	☆
P4-35	S1 igbu oge	0.0s ~ 3600.0s	0.0s	★
P4-36	S2 igbu oge	0.0s ~ 3600.0s	0.0s	★
P4-37	S3 igbu oge	0.0s ~ 3600.0s	0.0s	★
P4-38	Nhọrọ ụdị ọrụ S1 ~ S5 1	0: elu arụ ọrụ 1: arụ ọrụ obere Bit: S1 Iri: S2 Ebe narị: S3 Ọtụtụ puku ibe n'ibe: S4 Nde: S5	00000	★

Otu P5: Ọpụpụ Mpụta
P5-02	Nhọrọ ọrụ 1 agbagharịa (TA-TC)	0: mmepụta pulse (HDP) 1: mmepụta mgbanwe (HDY)	2	☆
P5-02	Nhọrọ ọrụ 1 agbagharịa (TA-TC)	0: Enweghị mmepụta 1: Ihe ntụgharị na-agba ọsọ 2: Mmebi mmejọ (nkwụsị mmejọ) 3: Nchọpụta ọkwa ugboro ugboro FDT1 mmepụta 4: ugboro na-abịarute 5: Ọrụ ọsọ efu (enweghị mmepụta na nkwụsị) 6: moto bufee tupu oti mkpu 7: Inverter ibu ibu tupu oti mkpu 8: Tọọ ọnụ ahịa ọnụọgụ ka iru 9: Na-akọwapụta na ọnụ ahịa ọnụọgụ ruru 10: ogologo ruo 11: okirikiri PLC zuru ezu 12: Oge ịgba ọsọ na-agbakọta abịarute 13: Oke ugboro 14: Oke ike 15: Njikere maka agba ọsọ 16: AI1>AI2 17: ọbịbịa kacha elu 18: mbata ugboro ugboro (ọrụ metụtara) 19:Undervoltage status mmepụta 20: nzikọrịta ozi 21: Nhazi nke emecha (debere) 22: ọnọdụ nso (echekwabara) 23: ọsọ ọsọ efu 2 (nakwa mmepụta mgbe a kwụsịrị) 24: ngụkọta oge ike-elu rutere 25: Frequency level 26: Frequency 1 rute ihe arụpụta 27: Ugboro 2 rute nrụpụta 28: nke ugbu a 1 ruru 29: nke ugbu a 2 ruru 30: Oge mbata. 31: Ntinye AI1 karịrị akarị 32: Ibunye 33: tụgharịa na-agba ọsọ 34: steeti efu ugbu a 35:Module okpomoku rutere 36: Ugbua ihe mmepụta gafere 37: mbata ugboro ugboro (mmechi na mmepụta) 38: Mwepụta mkpu (na-aga n'ihu) 39:Motor over Ịdọ aka ná ntị okpomọkụ 40: Oge ịgba ọsọ a rutere 41: mmejọ mmejọ (maka mmejọ nkwụsị efu), na n'okpuru voltage abụghị mmepụta	2	☆
P5-07	Nhọrọ ọrụ mmepụta A01	0:Ugboro arụ ọrụ 1: Ntọala ugboro ugboro 2: mmepụta ihe dị ugbu a 3: ikike mmepụta 4: ike mmepụta 5: mmepụta vol.tage 6: Ntinye usu dị elu (100% dakọtara 100.0khz) 7:AI1 8:AI2 9:AI3 10:ogologo 11: Ọnụ uru 12:Ntọala nkwukọrịta 13:Moto ọsọ 14:Mpụta ugbu a:(100% kwekọrọ 1000.0A) 15: mmepụta vol.tage (100% kwekọrọ na 1000.0V) 16: Mpụpụta moto (Uru n'ezie, Pụgharịatage ikwu na moto)	0	☆
P5-10	A01 Ihe nleba anya efu	- 100.0% ~ + 100.0%	0.0%	☆
P5-11	A01 nweta	- 10.00 ~ + 10.00	1.00	☆
Otu P6: njikwa mmalite/Kwụsị
P6-00	Ụdị mmalite	0: mmalite ozugbo 1: Inweta moto na-agbagharị agbagharị 2: Mmalite mbụ nwere obi ụtọ 3: mmalite ngwa ngwa SVC	0	☆
P6-01	Ụdị nke ijide moto na-agbagharị agbagharị	0: Site na nkwụsị nkwụsị 1: Site na 50Hz 2: Site na max. ugboro ugboro	0	★
P6-02	Ọsọ nke ijide moto na-agbagharị agbagharị	1-100	20	☆
P6-03	Malite ugboro ugboro	0.00Hz ~ 10.00Hz	0.00Hz	☆
P6-04	Malite oge ijide ugboro ugboro	0.0s ~ 100.0s	0.0s	★
P6-05	DC injection braking 1 larịị/ọkwa mkpali tupu	0% ~ 100%	50%	★
P6-06	DC injection braking 1 oge ọrụ/ tupu excitation n'ọrụ oge	0.0s ~ 100.0s	0.0s	★
P6-07	Ụdị osooso/Mbelata	0:Linear acceleration/ deceleration 1: S-curve acceleration/ deceleration A (static) 2: S curve acceleration/ deceleration B (ike)	0	★
P6-08	Ogologo oge nke ngalaba mmalite S-curve	0.0%~(100.0% -P6-09)	30.0%	★
P6-09	Ogologo oge nke akụkụ njedebe S-curve	0.0%~(100.0% -P6-08)	30.0%	★
P6-10	Modekpụrụ nkwụsị	0: Mee ka ọ kwụsịtụ 1: Oke mmiri ka ọ kwụsị	0	☆
P6-11	DC injection braking 2 ugboro ugboro na-amalite	0.00Hz~ kacha. ugboro (P0-10)	0.00Hz	☆
P6-12	DC injection braking 2 oge igbu oge	0.0s ~ 100.0s	0.0s	☆
P6-13	DC injection braking 2 larịị	0% ~ 100%	50%	☆
P6-14	DC injection braking 2 oge ọrụ	0.0s ~ 100.0s	0.0s	☆
P6-15	Oke ojiji breeki	0% ~ 100%	100%	☆
P6-18	Inweta oke moto na-agbagharị agbagharị ugbu a	30% ~ 200%	Ụdị dabere	☆
P6-21	Demagnetization oge (dị irè maka SVC)	0.00 ~ 5.00s	Ụdị dabere	☆
Otu P7: Ọrụ ahụ igodo na ngosipụta LED
P7-02	Kwụsị/Tọgharịa ọrụ igodo	0: Ọrụ nkwụsị igodo STOP/RES dị irè naanị n'oge ọrụ ahụigodo 1: Kwụsị / RES igodo nkwụsị na-arụ ọrụ na ụdị ọ bụla nke ọrụ	1	☆
P7-03	Ihe ngosi LED na-agba ọsọ paramita 1	0000~FFFF Bit00: Ugboro arụ ọrụ 1 (Hz) Bit01: Tọọ ugboro (Hz) Bit02: Vol.tage (V) Bit03: Mpụta voltage (V) Bit04: Mpụta dị ugbu a (A) Bit05: Ike mmepụta (kW) Bit06: torque mmepụta (%) Bit07: S ọkwa ntinye ọnụ Bit08: ọkwa mmepụta HDO Bit09: AI1 voltage (V) Bit10: AI2 Voltage (V) Bit11: AI3 Voltage (V) Bit12: Gụta uru Bit13: Uru ogologo Bit14: Ngosipụta ọsọ ibu Bit15: Ntọala PID	1F	☆
P7-04	Ihe ngosi LED na-agba ọsọ paramita 2	0000~FFFF Bit00: PID nzaghachi Bit01: PLC stage Bit02: Ugboro ntinye usu na-agba ọsọ dị elu (kHz) Bit03: Ugboro arụ ọrụ 2 (Hz) Bit04: Oge ịgba ọsọ fọdụrụ Bit05: AI1 tupu mgbazi vol.tage (V) Bit06: AI2 tupu mgbazi voltage (V) Bit07: AI3 mgbazi tupu voltage (V) Bit08: Ọsọ ahịrị Bit09: ike ugbu a n'oge (awa) Bit10: Oge na-agba ọsọ ugbu a (Min) Bit11: Oge ntinye ọsọ ọsọ dị elu (Hz) Bit12: Nkwukọrịta ntọala Bit13: Encoderfeedback ọsọ (Hz) Bit14: Isi ugboro A ngosi (Hz) Bit15: Ngosipụta ugboro abụọ nke abụọ (Hz)	0	☆

P7-05	Ihe nkwụsị ihe ngosi LED	0000~FFFF Bit00: Tọọ ugboro (Hz) Bit01: Ụgbọ ala voltage (V) Bit02: S ọkwa ntinye Bit03: HDO ọkwa mmepụta Bit04: AI1 voltage (V) Bit05: AI2 voltage (V) Bit06: AI3 voltage (V) Bit07: Ọnụ uru Bit08: Uru ogologo Bit09: PLC stage Bit10: Ọsọ ibu Bit11: Ntọala PID Bit12: ugboro ntinye ọsịsọ dị elu (kHz)	33	☆
P7-06	Ọnụego ngosipụta ọsọ nke ibu	0.0001-6.5000	1.0000	☆
P7-07	Heatsink okpomọkụ nke AC Drive IGBT	-20.0 ℃ ~ 120.0 ℃	–	●
P7-09	Oge ịgbakọ ọnụ	0h ~ 65535h	–	●
P7-12	Ọnụọgụ nke ntụpọ ntụpọ maka ngosi ọsọ ibu	Bit: d0-14 ọnụ ọgụgụ nke ntụpọ ntụpọ 0: 0 ntụpọ ntụpọ 1: 1 nkeji iri abụọ 2: 2 decimal ebe 3: 3 nkeji iri: d0-19/d0-29 ọnụọgụgụ nkeji 1: 1 nkeji iri 2 : 2 nkeji iri	21	☆
P7-13	Mkpokọta ike-na oge	0h ~ 65535h	–	●
P7-14	Mkpokọta ike oriri	0kW ~ 65535 kW	–	●
Otu P8: Ọrụ inyeaka
P8-04	Oge mbelata 2	0.0s rue 6500.0s	Ụdị dabere	☆
P8-05	Oge osooso 3	0.0s rue 6500.0s	Ụdị dabere	☆
P8-06	Oge mbelata 3	0.0s rue 6500.0s	Ụdị dabere	☆
P8-07	Oge osooso 4	0.0s rue 6500.0s	Ụdị dabere	☆
P8-08	Oge mbelata 4	0.0s rue 6500.0s	Ụdị dabere	☆
P8-09	Mwụ elu ugboro ugboro 1	0.00Hz ruo oke. ugboro ugboro	0.00Hz	☆
P8-10	Mwụ elu ugboro ugboro 2	0.00Hz ruo oke. ugboro ugboro	0.00Hz	☆
P8-11	Ugboro na-awụlikwa elu	0.00Hz ruo oke. ugboro ugboro	0.00Hz	☆
P8-12	Ngbanwe na-aga n'ihu/atụgharị ọsọ gafere oge mpaghara nwụrụ anwụ	0.0s rue 3000.0s	0.0s	☆
P8-13	Weghachite nhọrọ RUN	0: adịghị mma, 1: dị irè	0	☆
P8-14	Ọnọdụ na-agba ọsọ mgbe ntụaka ugboro dị ala karịa oke ala ugboro ole	0 ruo 2	0	☆
P8-15	Ọnụego mbelata	0.00% ruo 100.00%	0.00%	☆
P8-16	Mkpokọta ike-na ọnụ ụzọ oge	0 ruo 65000h	0h	☆
P8-17	Ogologo oge ịgba ọsọ nke mkpokọta	0 ruo 65000h	0h	☆
P8-18	Nhọrọ nchedo mmalite	0: Agaghị echekwa ya, 1: chebe	0	☆
P8-19	Uru nchọpụta ugboro ugboro 1	0.00Hz ruo oke. ugboro ugboro	50.00Hz	☆
P8-20	Nchọpụta hysteresis ugboro ugboro 1	0.0% ruo 100.0%	5.0%	☆
P8-21	Achọpụtara obosara obosara nke ebumnuche ebumnuche	0.0% ruo 100.0%	0.0%	☆
P8-22	Malite ọrụ ugboro ugboro	0: adịghị mma, 1: dị irè	0	☆
P8-25	Oge ngbanwe nke oge accel 1 na oge accel 2	0.00Hz ruo oke. ugboro ugboro	0.00Hz	☆
P8-26	Ugboro mgbanwe nke oge decel 1 na oge decel 2	0.00Hz ruo oke. ugboro ugboro	0.00Hz	☆
P8-27	Tọọ ihe kacha mkpa maka ọrụ JOG ọnụ	0: adịghị mma, 1: dị irè	0	☆
P8-28	Uru nchọpụta ugboro ugboro 2	0.00Hz ruo oke. ugboro ugboro	50.00Hz	☆
P8-29	Nchọpụta hysteres ugboro ugboro bụ 2	0.0% ruo 100.0%	5.0%	☆
P8-30	Nchọpụta ugboro 1	0.00Hz ruo oke. ugboro ugboro	50.00Hz	☆
P8-31	obosara nchọpụta nke ugboro 1	0.0% ruo 100.0% (max.frequency)	0.0%	☆
P8-32	Nchọpụta ugboro 2	0.00Hz ruo oke. ugboro ugboro	50.00Hz	☆
P8-33	obosara nchọpụta nke ugboro 2	0.0% ruo 100.0% (oke ugboro)	0.0%	☆
P8-34	Ọkwa nchọpụta efu ugbu a	0.0% ruo 300.0% (moto a na-egosi ugbu a)	5.0%	☆
P8-35	Oge nchọta efu ugbu a	0.01s rue 600.00s	0.10s	☆
P8-36	Mbupute karịrị ọnụ ụzọ dị ugbu a	1.1% (enweghị nchọpụta) 1.2% ruo 300.0% (moto a na-egosi ugbu a)	200.0%	☆
P8-37	Nsonaazụ n'ofe oge nchọpụta ugbu a	0.00s rue 600.00s	0.00s	☆
P8-38	Ọkwa nchọpụta nke ugbu a 1	0.0% ruo 300.0% (moto a na-egosi ugbu a)	100.0%	☆
P8-39	Ogologo nchọpụta nke ugbu a 1	0.0% ruo 300.0% (moto a na-egosi ugbu a)	0.0%	☆
P8-40	Ọkwa nchọpụta nke ugbu a 2	0.0% ruo 300.0% (moto a na-egosi ugbu a)	100.0%	☆
P8-41	Ogologo nchọpụta nke ugbu a 2	0.0% ruo 300.0% (moto a na-egosi ugbu a)	0.0%	☆
P8-42	Ọrụ oge	0: adịghị mma 1: dị irè	0.0%	★
P8-43	Ọwa nhazi oge na-agba ọsọ	0 ruo 3	0	★
P8-44	Oge ịgba ọsọ	0.0 ruo 6500.0 min	0.0 min	★
P8-45	Ntinye AI1 voltage ala ịgba	0.00V ka F8-46	3.10V	☆
P8-46	Ntinye AI1 voltage elu oke	F8-45 ruo 10.00V	6.80V	☆
P8-47	IGBT okpomọkụ oke	0 ℃ ruo 100 ℃	75 ℃	☆
P8-48	Fọ na-ajụ oyi na-arụ ọrụ	0: Fan na-agba ọsọ n'oge arụ ọrụ 1: onye ofufe na-aga n'ihu	0	☆
P8-49	Ugboro edemede	F8-51 ruo oke. Ugboro (F0-10)	0.00Hz	☆
P8-50	Oge igbu oge na-eteta	0.0s ~ 6500.0s	0.0s	☆
P8-51	Ugboro ole na-ehi ụra	0.00Hz iji teta ugboro ugboro (P8-49)	0.00Hz	☆
P8-52	Oge igbu oge na-ehi ụra	0.0s ~ 6500.0s	0.0s	☆
P8-53	Ogologo oge na-agba ọsọ oge a	0.0 ~ 6500.0 nkeji	0.0 min	☆
P8-54	Ọnụọgụ mgbazi ike mmepụta	0.0% ruo 200.0%	100.0%	☆
Otu P9: Mmejọ na Nchekwa
P9-00	Nchekwa oke ibu moto	0: Amachibidoro 1: ekwe	1	☆
P9-01	Uru nchebe oke ibu moto	0.20 ruo 10.00	1.00	☆
P9-02	Ọnụọgụ ịdọ aka na ntị bufee moto	50% ruo 100%	80%	☆
P9-03	Mfefetage nchebe uru	0-100	30	☆
P9-04	Mfefetage nchebe voltage	650 ruo 800V	770V	☆
P9-07	Nchọpụta nke mkpirisi okirikiri ka ala n'elu ike	Nkeji: Nhọrọ nchebe mkpirisi ike ruo n'ala 0: adịghị mma 1: Ebe iri dị irè: Nhọrọ nke nchebe dị mkpụmkpụ ruo ala tupu ịgba ọsọ 0: adịghị mma	01	☆
P9-08	Ngwa breeki etinyere voltage	650 ruo 800V	720V	☆

P9-09	Oge nrụpụta akpaaka		0 ruo 20			0	☆
P9-10	Nhọrọ nke omume DO n'oge nrụpụta akpaaka		0: Enweghị omume 1: Omume			0	☆
P9-11	Igbu oge nrụpụta akpaaka		0.1s rue 100.0s			1.0s	☆
P9-12	Ntinye oge mfu/nchekwa mgbanaka mbufe chaja		Ọnụọgụ nkeji: ntinye nhọpụta nchebe ọnwụ nke ngalaba nke iri: Nhọrọ nchekwa kọntaktị ma ọ bụ dọba 0: Amachibidoro 1: Hapụrụ			–	–
P9-13	Nchekwa ọnwụ nke oge mmepụta		Ọnụọgụ nkeji : nhọpụta nchedo nhụsianya nke mmepụta 0: Amachibidoro 1: Ebe a na-ahapụ ọtụtụ iri: nhọrọ nchebe ọnwụ nke mmepụta tupu ịgba ọsọ 0: Amachibidoro 1: ekwe			01	☆
P9-14	Ụdị mmejọ nke mbụ		00-55			–	●
P9-15	Ụdị mmejọ nke abụọ					–	●
P9-16	Ụdị mmejọ nke atọ (kacha ọhụrụ).					–	●
P9-17	Ugboro na mmejọ nke atọ		–			–	●
P9-18	Ugbu a n'ihi mmejọ nke atọ		–			–	●
P9-19	Ụgbọ ala voltage n'elu mmejọ nke atọ		–			–	●
P9-20	DI steeti na mmejọ nke atọ		–			–	●
P9-21	Kwupụta na mmejọ nke atọ		–			–	●
P9-22	AC mbanye steeti nwere mmejọ nke atọ		–			–	●
P9-23	Ike-oge n'elu mmejọ nke atọ		–			–	●
P9-24	Na-agba ọsọ oge na mmejọ nke 3		–			–	●
P9-27	Ugboro n'elu mmejọ nke abụọ		–			–	●
P9-28	Ugbu a n'elu mmejọ nke abụọ		–			–	●
P9-29	Ụgbọ ala voltage n'elu mmejọ nke abụọ		–			–	●
P9-30	DI steeti na mmejọ nke abụọ		–			–	●
P9-31	KWUO n'ihi mmejọ nke abụọ		–			–	●
P9-32	Ọnọdụ draịva AC na mmejọ nke abụọ		–			–	●
P9-33	Ike-na oge n'elu mmebi nke abụọ		–			–	●
P9-34	Oge na-agba ọsọ na mmejọ nke abụọ		–			–	●
P9-37	Ugboro na mmejọ nke mbụ		–			–	●
P9-38	Ugbu a n'ihi mmejọ nke mbụ		–			–	●
P9-39	Ụgbọ ala voltage n'elu mmebi nke 1st		–			–	●
P9-40	DI steeti na mmejọ nke mbụ		–			–	●
P9-41	KWUO n'ihi mmejọ nke mbụ		–			–	●
P9-42	Ọnọdụ ụgbọala AC n'ihi mmejọ nke mbụ		–			–	●
P9-43	Ike-na oge na mmejọ 1st		–			–	●
P9-44	Oge na-agba ọsọ na mmejọ 1st		–			–	●
P9-47	Nhọrọ ọrụ nchedo mmejọ 1		0: free 1: kwụsị 2. nọgide na-agba ọsọ			00000	☆
P9-48	Nhọrọ ọrụ nchedo mmejọ 2		00000 ruo 11111			00000	☆
P9-49	Nhọrọ ọrụ nchedo mmejọ 3		00000 ruo 22222			00000	☆
P9-50	Nhọrọ ọrụ nchedo mmejọ 4		00000 ruo 22222			00000	☆
P9-54	Nhọrọ ugboro ugboro maka ịga n'ihu na-agba ọsọ na mmejọ		0 ruo 4			0	☆
P9-55	Ndabere ugboro ugboro na mmejọ		0.0% ruo 100.0% (max. FrequencyP0-10)			100.0%	☆
P9-56	Ụdị ihe mmetụta okpomọkụ moto		0: Enweghị ihe mmetụta okpomọkụ 1: Pt100 2: PT1000			–	–
P9-59	Mbugharị ike-site na nhọrọ ọrụ		0: adịghị mma 1: ụgbọ ala mgbe niile voltage njikwa 2: deceleration kwụsị			0	☆
P9-60	Agbanyụrụ ọnụ ụzọ mịnye ike site na ọrụ		80% ruo 100%			85%	☆
P9-62	Agbanyere ọnụ ụzọ ịgbanye ike site na ọrụ		60% ruo 100%			80%	☆
P9-63	Ibu nchekwa furu efu		0: Agbanyụrụ 1: Agbanyere			0	☆
P9-64	Ibu ọkwa nchọpụta furu efu		0.0% ruo 100.0%			10.0%	☆
P9-65	Ibu oge nchọpụta furu efu		0.0s rue 60.0s			1.0s	☆
P9-67	Ọkwa nchọta oke ọsọ		0.0% ruo 50.0% (max.frequency)			20.0%	☆
P9-68	Oge nchọta oke ọsọ		0.0s rue 60.0s			1.0s	☆
P9-69	Ọkwa nchọpụta nke njehie ọsọ		0.0% ruo 50.0% (max.frequency)			20.0%	☆
P9-70	Oge nchọpụta ọsọ ọsọ		0.0s rue 60.0s			5.0s	☆
P9-71	Ịgbanye ike-site na uru Kp		0 ruo 100			40	☆
P9-72	Mbunye ike na-agba ọsọ-site na ọnụọgụ ọnụọgụ		0 ruo 100			30	☆
P9-73	Oge mbelata nke itinye ike n'ịnyịnya-site		0.0s rue 300.0s			20.0s	★
Otu PA: Ọrụ PID
PA-00		Ọwa ntọala ntụaka PID		0: PA-01 ntọala 1: AI1 (Mara: J6 jumper) 2: AI2 3: AI3 4: Ntọala ntinye ụda ọsịsọ dị elu (S5) 5: enyere nzikọrịta ozi 6: Multi-ngalaba ntụziaka nyere	0		☆
PA-01		Ntọala dijitalụ PID		0.0v% ruo 100.0%	50.0%		☆
PA-02		Nzaghachi PID		0: AI1 (Mara: J6 jumper) 1: AI2 2: AI3 3: AI1-AI2 4: Ntọala ntinye ụda ọsịsọ dị elu (S5) 5: Nzikọrịta ozi enyere 6: AI1 + AI2 7: MAX (\| AI1 \|, \| AI2 \|) 8: MIN (\| AI1 \|, \| AI2 \|)	0		☆
PA-03		Ntuziaka ọrụ PID		0: Omume dị mma 1: mmeghachi omume	0		☆
PA-04		Ntuziaka PID na oke nzaghachi		0 ruo 65535	1000		☆
PA-05		Uru nha nha nha Kp1		0.0 ruo 1000.0	20.0		☆
PA-06		Oge njikọta Ti1		0.01s rue 10.00s	2.00s		☆
PA-07		Oge dị iche iche Td1		0.000s rue 10.000s	0.000s		☆
PA-08		Oke mmepụta PID na ntụgharị ntụgharị		0.00 Hz ka kacha. Ugboro P0-10	0.00Hz		☆
PA-09		Oke mperi PID		0.0% ruo 100.0%	0.0%		☆
PA-10		Oke dị iche iche PID		0.00% ruo 100.00%	0.10%		☆
PA-11		Oge mgbanwe PID		0.00s rue 650.00s	0.00s		☆
PA-12		Oge nzacha PID		0.00s rue 60.00s	0.00s		☆
PA-13		Oge nzacha mmepụta PID		0.00s rue 60.00s	0.00s		☆
PA-14		Echekwara		–	–		–
PA-15		Uru nha nha nha Kp2		0.0 ruo 1000.0	20.0		☆
PA-16		Oge njikọta Ti2		0.01s rue 10.00s	2.00s		☆
PA-17		Oge dị iche iche Td2		0.000s rue 10.000s	0.000s		☆
PA-18		PID ngbanwe n'elu ọnọdụ		0 ruo 3	0		☆
PA-19		Njehie PID 1 maka ngbanwe akpaaka		0.0% ruo PA-20	20.0%		☆
PA-20		Njehie PID 2 maka ngbanwe akpaaka		PA-19 ruo 100.0%	80.0%		☆
PA-21		PID uru mbụ		0.0% ruo 100.0%	0.0%		☆
PA-22		PID uru mmalite oge ọrụ		0.00s rue 650.00s	0.00s		☆

PA-23	Ntugharị mmepụta abụọ na-aga n'ihu ruo kacha	0.0% ruo 100.0%	1.00%	☆
PA-24	Ntugharị mmepụta abụọ na-atụgharị kacha	0.0% ruo 100.0%	1.00%	☆
PA-25	PID ihe onwunwe	00 ruo 11	00	☆
PA-26	Ọkwa nchọpụta mfu nzaghachi PID	0.0%: Enweghị nchọpụta 0.1% ruo 100.0%	0.0%	☆
PA-27	Oge nchọpụta mfu nzaghachi PID	0.0s rue 20.0s	0.0s	☆
PA-28	Nhọrọ nke ọrụ PID na nkwụsị	0: Kwụsị enweghị ọrụ, 1: arụ ọrụ oge ala	0	☆
Otu Pb: Ọrụ Wobble, Ogologo a kapịrị ọnụ na agụta
Pb-00	Ụdị ntọala Wobble	0: 0: n'ihe gbasara ugboro etiti, 1: n'ihe gbasara ugboro kacha	0	☆
Pb-01	Bkpa ike amplitude	0.0% ruo 100.0%	0.0%	☆
Pb-02	Nzọụkwụ na-akpaghasị	0.0% ruo 50.0%	0.0%	☆
Pb-03	okirikiri mgbada	0.1s rue 3000.0s	10.0s	☆
Pb-04	Ogologo oge ebili mmiri triangular na-ebilite oge	0.1% ruo 100.0%	50.0%	☆
Pb-05	Tọọ ogologo	0 ruo 65535m	1000m	☆
Pb-06	Ogologo ogologo	0 ruo 65535m	0m	☆
Pb-07	Ọnụọgụ nke pulses kwa mita	0.1 ~ 6553.5	100.0	☆
Pb-08	Tọọ uru ọnụọgụgụ	1 ~ 65535	1000	☆
Pb-09	Ezipụta uru ọnụọgụgụ	1 ~ 65535	1000	☆
Otu PC: Multi-reference na Simple PLC Arụ
PC-07	Ntụaka 7	- 100.0% ruo 100.0%	0.0%	☆
PC-08	Ntụaka 8	- 100.0% ruo 100.0%	0.0%	☆
PC-09	Ntụaka 9	- 100.0% ruo 100.0%	0.0%	☆
PC-10	Ntụaka 10	- 100.0% ruo 100.0%	0.0%	☆
PC-11	Ntụaka 11	- 100.0% ruo 100.0%	0.0%	☆
PC-12	Ntụaka 12	- 100.0% ruo 100.0%	0.0%	☆
PC-13	Ntụaka 13	- 100.0% ruo 100.0%	0.0%	☆
PC-14	Ntụaka 14	- 100.0% ruo 100.0%	0.0%	☆
PC-15	Ntụaka 15	- 100.0% ruo 100.0%	0.0%	☆
PC-16	Mfe PLC na-agba ọsọ mode	0: Kwụsị na njedebe nke otu ịgba ọsọ 1: Debe uru ikpeazụ na njedebe nke otu ọsọ 2: nọgide na-ekesa	0	☆
PC-17	Nhọrọ njigide PLC dị mfe	Otu ọnụọgụ: nhọrọ ebe nchekwa mgbada 0: Enweghị ebe nchekwa mgbe ike gbanyụrụ 1: ebe nchekwa mgbada Ebe iri: Kwụsị nhọrọ ebe nchekwa 0: Kwụsị ebe nchekwa 1: ebe nchekwa mechie	00	☆
PC-18	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 0	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-19	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 0	0 ruo 3	0	☆
PC-20	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 1	0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-21	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 1	0 ruo 3	0	☆
PC-22	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 2	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-23	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 2	0 ruo 3	0	☆
PC-24	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 3	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-25	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 3	0 ruo 3	0	☆
PC-26	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 4	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-27	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 4	0 ruo 3	0	☆
PC-28	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 5	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-29	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 5	0 ruo 3	0	☆
PC-30	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 6	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-31	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 6	0 ruo 3	0	☆
PC-32	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 7	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-33	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 7	0 ruo 3	0	☆
PC-34	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 8	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-35	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 8	0 ruo 3	0	☆
PC-36	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 9	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-37	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 9	0 ruo 3	0	☆
PC-38	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 10	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-39	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 10	0 ruo 3	0	☆
PC-40	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 11	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-41	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 11	0 ruo 3	0	☆
PC-42	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 12	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-43	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 12	0 ruo 3	0	☆
PC-44	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 13	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-45	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 13	0 ruo 3	0	☆
PC-46	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 14	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-47	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 14	0 ruo 3	0	☆
PC-48	Oge na-agba ọsọ nke ntụnye aka PLC dị mfe 15	0.0s (h) ruo 6500.0s (h)	0.0s (h)	☆
PC-49	Oge osooso / mbelata nke ntụnye aka PLC dị mfe 15	0 ruo 3	0	☆
PC-50	Oge nkeji nke PLC dị mfe na-agba ọsọ	0:s, 1:h	0	☆

PC-51	Ntuziaka 0 isi iyi	0: Koodu ọrụ PC-00 ka enyere 1: AI1 2: AI2 3: AI3 4: Ntinye usu dị elu 5: PID 6: Preset ugboro (P0-08) nyere, elu/ala nwere ike gbanwee	0	☆
Otu Pd: Nkwukọrịta
Pd-00	Ọnụ ego baud	Bit: MODBUS 0: 300BPS 1: 600BPS 2: 1200BPS 3: 2400BPS 4: 4800BPS 5: 9600BPS 6: 19200BPS 7: 38400BPS 8: 57600BP 9: 115200BPS Iri: debe Narị: echekwabara	005	☆
Pd-01	Akara usoro data	0: enweghị parity (8-N-2) 1: Ọbụla nlele (8-E-1) 2: Odd parity (8-O-1) 3: Ọnweghị oke (8-N-1)	0	☆
Pd-02	Adreesị mpaghara	0: adreesị mgbasa ozi; 1 ruo 247	1	☆
Pd-03	Oge ịzaghachi	0 ruo 20 ms	2	☆
Pd-04	Oge ngwụcha nke nkwukọrịta	1.1: 1.2:s ruo 60.0s adịghị mma	0.0	☆
Pd-05	Nhọrọ protocol Modbus yana etiti data PROFIBUS-DP	Bit: MODBUS 0: Usoro MODBUS na-abụghị ọkọlọtọ 1: ọkọlọtọ MODBUS protocol	30	☆
Pd-06	Mkpebi dị ugbu a na-agụ site na nzikọrịta ozi	0: 0.01 1: 0.1	0	☆
Otu PE: Oke-akọwapụtara onye ọrụ
PE-00	Oke akọwapụtara onye ọrụ 0	P0-00 ~ PP-xx A0-00 ~ Ax-xx d0-00 ~ d0-xx d3-00 ~ d3-xx	d3-17	☆
PE-01	Parametị akọwapụtara onye ọrụ1		d3-18	☆
PE-02	Oke akọwapụtara onye ọrụ 2		P0.00	☆
…………	…….		P0.00	☆
PE-29	Oke akọwapụtara onye ọrụ 29		P0.00	☆
Otu PP: Ọrụ Parameter Management
PP-00	Oru paswọọdụ	0 ruo 65535	0	☆
PP-01	Mmalite oke	0: Enweghị ọrụ 1: Weghachite ụlọ ọrụ 0: Enweghị ọrụ 1: Weghachite paramita ụlọ ọrụ ma e wezụga paramita moto 2: Kpochapụ ndekọ 4: Kwado paramita onye ọrụ ugbu a 501: Weghachite oke ndabere onye ọrụ.	0	☆
PP-02	Ngosipụta akụrụngwa	Bit: d otu ngosi nhọrọ 0: egosighi 1: ngosi iri: Otu A na-egosi nhọrọ 0: egosighi 1: ngosi	11	★
PP-03	Nhọrọ nke ngosipụta oke n'otu n'otu	Bit: nhọrọ ngosipụta oke otu onye ọrụ 0: egosighi 1: ngosi iri: Onye ọrụ Change Parameter Group Ngosipụta Nhọrọ 0: egosighi 1: ngosi	00	☆
PP-04	Nhọrọ nke mgbanwe parameter	0: nwere ike gbanwee 1: enweghị ike gbanwee	0	☆
Otu A0: Njikwa Torque na oke
A0-00	Nhọrọ njikwa ọsọ/Torque	0: njikwa ọsọ 1: njikwa torque	0	★
A0-01	Isi iyi ntụaka torque na njikwa torque	0: Ntọala dijitalụ 1 (A0-03) 1: AI1 (Mara: J6 jumper) 2: AI2 3: AI3 4: Ntinye ngwa ngwa ngwa ngwa (S5) 5: Nkwukọrịta nyere 6: MIN (AI1, AI2) 7: MAX (AI1, AI2) (1-7 nhọrọ zuru oke, kwekọrọ na ntọala A0-03 dijitalụ)	0	★
A0-03	Ntọala dijitalụ torque na njikwa torque	- 200.0% ruo 200.0%	150.0%	☆
A0-05	N'ihu max. ugboro ugboro na torque akara	0.00Hz ruo oke ugboro:z(P0-10)	ka	ma x.
A0-06	tụgharịa max. ugboro ugboro na torque akara	0.00Hz (P0-10)	ka	ma x.
A0-07	Oge osooso na njikwa torque	0.00s rue 65000s	0.00s	☆
A0-08	Oge mbelata na njikwa torque	0.00s rue 65000s	0.00s	☆
A2-47	Isi iyi oke torque na njikwa ọsọ	0: A2-48 ntọala 1: AI1 (Rịbama: J6 jumper) 2: AI2 3: AI3 4: Ntinye ngwa ngwa ngwa ngwa (S5) 5: nzikọrịta ozi nyere 6: MIN (AI1, AI2) 7: MAX (AI1, AI2) ) 1-7 nhọrọ zuru oke, kwekọrọ na ntọala dijitalụ A2-48	0	☆
A2-48	Ntọala dijitalụ nke oke torque na njikwa ọsọ	0.0% ruo 200.0%	150.0%	☆
A2-49	Isi iyi oke oke na njikwa ọsọ (mmeghari)	0: Koodu ọrụ P2-10 ntọala 1: AI1 (Cheta: J6 jumper)	0	☆
Otu A5: njikwa njikwa
A5-00	DPWM ngbanwe karịa oke oke ugboro ole	5.00Hz ruo oke. ugboro ugboro	8.00Hz	☆
A5-01	Ụkpụrụ mgbanwe PWM	0: Asynchronous modulation, 1: Mmekọrịta mmekọrịta	0	☆
A5-02	Nhọrọ ụdị akwụ ụgwọ mpaghara nwụrụ anwụ	0: Enweghị akwụ ụgwọ, 1: Ụdị nkwụghachi ụgwọ 1	1	☆
A5-03	omimi PWM random	0 :PWM adịghị mma 1:PWM nwere ike họrọ	0	☆
A5-04	N'elu mgbochi ngwa ngwa ugbu a	0:kwa 1: enweghị ike	1	☆
A5-05	Voltage n'elu modulation ọnụọgụ	100% ruo 110%	105%	★
A5-06	N'okpuru voltage ụzọ	150 ruo 420V	350V	☆
A5-08	Ndozi oge mpaghara nwụrụ anwụ	0.0% ruo 8.0%	0.0%	★
A5-09	N'elu voltage ụzọ	650 ruo 820V	Ụdị dabere	★
Otu A6: AI CA6 Otu: AI Curve Settingurve Setting
A6-00	Usoro AI 4 min. ntinye	- 10.00V ruo A6-02	0.00V	☆
A6-01	Pasent kwekọrọtage nke AI curve 4 min. ntinye	- 100.0% ruo 100.0%	0.0%	☆
A6-02	AI curve 4 na ntinye flexion 1	A6-00 ruo A6-04	3.00V	☆
A6-15	Pasent kwekọrọtage nke AI curve 5 max. ntinye	- 100.0% ruo 100.0%	30.0%	☆
A6-24	Mwụli elu nke ntọala ntinye kwekọrọ AI1	- 100.0% ruo 100.0%	0.0%	☆

Otu AC: AIAO mmezi
AC-00	AI1 tụrụ voltage 1	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆
AC-01	AI1 gosipụtara voltage 1	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆
AC-02	AI1 tụrụ voltage 2	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆
AC-03	AI1 gosipụtara voltage 2	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆
AC-12	Ao1 Target voltage1	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆
AC-13	Ao1 tụrụ voltage 1	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆
AC-14	AO1Target voltage 2	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆
AC-15	Ao1 tụrụ voltage 2	- 10.00 ruo 10.000V	ụlọ ọrụ emeziri	☆

Usoro nlekota oru

Koodu ọrụ	Aha	Ngosipụta nso	Adreesị Nkwurịta Okwu
Otu d0: Nleba anya
d0-00	Ugboro ugboro	0.01Hz	7000H
d0-01	Ntuziaka ugboro ugboro	0.01Hz	7001H
d0-02	Ụgbọ ala voltage	0.1V	7002H
d0-03	Mmepụta voltage	1V	7003H
d0-04	Mpụta ugbu a	0.01A	7004H
d0-05	Ike mmepụta	0.1kW	7005H
d0-06	Mpụpụ torque	0.1%	7006H
d0-07	S ndenye steeti	1	7007H
d0-08	Ọnọdụ mmepụta HDO	1	7008H
d0-09	AI1 voltage	0.01V	7009H
d0-10	AI2 voltage/ugbu a	0.01V/0.01mA	700 AH
d0-11	AI3 voltage	0.01V	700 BH
d0-12	Gụọ uru	1	700CH
d0-13	uru ogologo	1	700DH
d0-14	Ngosipụta ọsọ ọsọ	1	700EH
d0-15	Ntuziaka PID	1	700FH
d0-16	Nzaghachi PID	1	7010H
d0-17	PLC stage	1	7011H
d0-18	Nrụtụ aka Pulse	0.01kHz	7012H
d0-19	ọsọ nzaghachi	0.01Hz	7013H
d0-20	Oge ịgba ọsọ fọdụrụnụ	0.1Nkeji	7014H
d0-21	AI1 voltage tupu mgbazi	0.001V	7015H
d0-22	AI2 voltage (V)/ ugbu a (MA) tupu mgbazi	0.001V/0.01mA	7016H
d0-23	AI3 voltage tupu	0.001V	7017H
d0-24	Ọsọ moto	1m/Nkeji	7018H
d0-25	Mkpokọta ike-na oge	1Nkeji	7019H
d0-26	Oge ịgbakọ ọnụ	0.1Nkeji	701 AH

Ngosipụta mmejọ

Koodu mmejọ	Mmejọ
FU02	Kafe ugbu a n'oge osooso
FU03	Karịrị ugbu a n'oge deceleration
FU04	N'ofe ugbu a na ọsọ mgbe niile
FU05	N'elu voltage n'oge osooso
FU06	N'elu voltage n'oge deceleration
FU07	N'elu voltage na ọsọ ọsọ
FU08	Mmejọ resistor tupu chaja
FU09	N'okpuru voltage
FU10	bufee AC mbanye
FU11	Ibufe moto
FU13	Ọpụpụ oge mmepụta
FU14	ikpo oke ọkụ
FU15	Ọpụpụ mmejọ ọrụ
FU16	Mmejọ nzikọrịta ozi
FU17	Kpọtụrụ ma ọ bụ mmejọ

Koodu mmejọ	Mmejọ
FU18	ọdịda nchọpụta ugbu a
FU19	Ịmụta moto onwe ya adịghị arụ ọrụ
FU20	Mmejọ koodu
FU21	EEPROM agụ-dee
FU23	Obere sekit ruo n'ala
FU26	Oge ịgbakọ ọnụ
FU27	Mmejọ akọwapụtara nke onye ọrụ 1
FU28	Mmejọ akọwapụtara nke onye ọrụ 2
FU29	Mkpokọta ike ruru njehie
FU30	Nfufu ibu
FU31	Nzaghachi PID furu efu mgbe a na-agba ọsọ
FU40	Pulse-by-pulse mperi mperi ugbu a
FU41	Mmejọ ngbanwe moto mgbe ọ na-agba ọsọ
Fu42	Ọsọ ọsọ karịrị oke
FU43	Moto karịrị ọsọ

Akwụkwọ / akụrụngwa

STEPPERONLINE EV200 Series Variable Frequency Drive [pdf] Akwụkwọ ntuziaka onye ọrụ
EV200-0400G-S2, EV200-0750G-S2, EV200-1500G-S2, EV200-2200G-S2, EV200-0750G-T3, EV200-1500G-T3, EV200G-2200 3- 200G-T3700, EV3, EV200 Series Variable Frequency Drive, Variable Frequency Drive, Frequency Drive

Ntụaka

Akwụkwọ ntuziaka onye ọrụ