Nice Roll-Control2 Z Wave Blind and Awning Controller
Tlhaloso ea Sehlahisoa le Likarolo
Roll-Control2 e lumella taolo e hole ea li-roller blinds, li-blind blinds, li-pergolas, likharetene, li-awnings le li-motors tse foufetseng tse nang le li-switch tsa elektroniki kapa tsa mochini.
Ho kenya
Pele ho Tlhophiso
Ho hokahanya sesebelisoa ka mokhoa o sa lumellaneng le bukana ho ka baka likotsi. Latela litataiso tsa lithapo tse fanoeng.
Mehato ea ho Kenya
- Tlosa lisebelisoa tsa motlakase voltage.
- Bula lebota la switjha lebokose.
- Hokela ho latela setšoantšo sa wiring se fanoeng.
- Netefatsa khokahano e nepahetseng.
- Lokisetsa sesebelisoa ka lebokoseng la ho fetola lebota.
- Koala lebota la switjha lebokose.
- Fetolela li-mains voltage.
Hlokomela: Sebelisa likhoele tse loketseng tsa ho kenya le likhokahano joalo ka ha ho boletsoe bukeng ea tataiso.
E eketsa ho Z-Wave Network
Ho kenya sesebelisoa ho netweke ea Z-Wave:
- Fumana konopo e khethehileng ea sesebelisoa (DSK) lebokoseng.
- Latela litaelo tse fanoeng ho qala ho para.
Ho tlosa ho tloha ho Z-Wave Network
Ho tlosa sesebelisoa ho netweke ea Z-Wave, latela mehato e boletsoeng bukeng ea tataiso.
Tekanyetso
- Eketsa kapa fokotsa boleng ba parametha joalo ka ha ho khothalelitsoe bukeng ea tataiso ho lekanya sesebelisoa.
- Haeba tlhahlobo e hloleha, sebelisa litlhophiso tsa paramethara bakeng sa ho fetola nako ea motsamao.
LBH
- Q: hole kae ke mefuta e fapaneng ya sesebediswa Roll-Control2?
A: Sesebelisoa se na le sebaka sa ho fihla ho limithara tse 100 ka ntle le ho fihla ho limithara tse 30 ka tlung, ho itšetlehile ka sebaka le mohaho oa mohaho. - P: Ke eng e khothalletsoang phepelo ea motlakase bakeng sa Roll-Control2?
A: The kgothaletswa phepelo ea matla ke 100-240 V ~ ho 50/60 Hz.
BOHLOKOA TŠIRELETSO
TLHOKOMELO! - Bala bukana ena pele u leka ho kenya sesebelisoa! Ho hloleha ho ela hloko likhothaletso tse kenyellelitsoeng bukaneng ena ho ka ba kotsi kapa ha baka tlolo ea molao. Moetsi, NICE SpA Oderzo TV Italia e ke ke ea jara boikarabello bakeng sa tahlehelo kapa tšenyo e bakoang ke ho se latele litaelo tsa buka ea ts'ebetso.
KOTSI EA MOTLATSI!
- Sesebelisoa se etselitsoe ho sebetsa ho kenya motlakase lapeng. Khokelo e fosahetseng kapa ts'ebeliso e ka baka mollo kapa ts'okelo ea motlakase.
- Le ha sesebelisoa se koetsoe, voltage ka ba teng liteisheneng tsa eona. Tlhokomelo efe kapa efe e hlahisang liphetoho ho tlhophiso ea likhokahano kapa mojaro o tlameha ho lula o etsoa ka fuse e holofetseng.
- Ho qoba kotsi ea ho tsukutloa ke motlakase, se ke oa sebelisa sesebelisoa ka matsoho a metsi kapa a mongobo.
- Mesebetsi eohle ea sesebelisoa e ka etsoa feela ke setsebi sa motlakase se tšoanelehang le se nang le tumello. Ela hloko melao ea naha.
TLHOKOMELO!
- Se ke oa fetola! - Se ke oa fetola sesebelisoa sena ka tsela efe kapa efe e sa kenyelletsoeng bukaneng ena.
- Lisebelisoa tse ling - Moetsi, NICE SpA Oderzo TV Italia e ke ke ea jara boikarabello bakeng sa tšenyo leha e le efe kapa tahlehelo ea litokelo tsa waranti bakeng sa lisebelisoa tse ling tse hokahaneng haeba khokahano e sa tsamaisane le libuka tsa bona.
- Sehlahisoa sena se reretsoe ho sebelisoa ka tlung feela libakeng tse omeletseng. – Se ke oa sebelisa ho damp kapa libaka tse metsi, haufi le bate, sinki, shaoara, letangoana la ho sesa, kapa kae kapa kae moo metsi kapa mongobo o leng teng.
- Ha ho khothalletsoe ho sebelisa li-roller blinds ka nako e le 'ngoe. Bakeng sa mabaka a tšireletso, bonyane sefofu se le seng sa roller se lokela ho laoloa ka boikemelo, ho fana ka tsela e sireletsehileng ea ho baleha maemong a tšohanyetso.
- Eseng ntho ea ho bapala! – Sehlahisoa sena ha se ntho ea ho bapala. Ipoloke hole le bana le diphoofolo!
TLHALOSO LE LITŠOANTŠISO
NICE Roll-Control2 ke sesebelisoa se etselitsoeng ho laola li-roller blinds, awnings, blinds tsa venetian, likharetene le li-pergolas.
NICE Roll-Control2 e thusa ho beha lifofu tse foufetseng kapa li-slats tsa venetian tse nepahetseng hantle. E u nolofalletsa ho laola lisebelisoa tse hokahaneng ebang ke ka marang-rang a Z-Wave® kapa ka sesebelisoa se hokahaneng ka kotloloho ho eona. Sesebelisoa se na le lisebelisoa tsa ho hlahloba matla.
Lintlha tse ka sehloohong
- E ka sebelisoa le:
- Li-roller blinds
- Lifofu tsa Venetian
- Pergolas
- Likharetene
- Awnings
- Li-motor tse foufetseng tse nang le li-switches tsa moeli oa elektroniki kapa oa mochini
- E na le metering ea matla
- E ts'ehetsa mekhoa ea ts'ireletso ea marang-rang ea Z-Wave®: S0 e nang le encryption ea AES-128 le mokhoa o netefalitsoeng oa S2 ka encryption e thehiloeng ho PRNG.
- E sebetsa joalo ka sesebelisoa sa Z-Wave® se pheta-phetoang (lisebelisoa tsohle tse sa sebetseng ka betri ka har'a marang-rang li sebetsa joalo ka li pheta-pheta ho eketsa ts'epo ea marang-rang)
- E ka sebelisoa le lisebelisoa tsohle tse netefalitsoeng ka setifikeiti sa Z-Wave Plus® mme e lumellana le lisebelisoa tse joalo tse hlahisoang ke bahlahisi ba bang.
- E sebetsa ka mefuta e fapaneng ea li-switches. Bakeng sa boiketlo ba ts'ebeliso, ho khothaletsoa ho sebelisa li-switches tse inehetseng ts'ebetsong ea shutter ea roller (monostable, roller shutter switch)
Sesebelisoa ke sehlahisoa sa Security Enabled Z-Wave Plus® 'me Setsi sa Ts'ireletso sa Z-Wave® Controller se hloka ho sebelisoa ho sebelisa sehlahisoa ka botlalo.
LIEKETSENG TS'OANELO
| Letlapa la A1 - Roll-Control2 - Litlhaloso | |
| Phepelo ea motlakase | 100-240 V ~ 50/60 Hz |
| E lekantsoe mojaro oa hona joale | 2 A bakeng sa li-motors tse nang le matla a lefelloang (meroalo e matla) |
| Mefuta e lumellanang ea mojaro |  li-motor tsa AC tsa mohato o le mong |
| Li-switches tse hlokahalang tsa moeli | Elektronike kapa mochine |
| Tšireletso e khothalletsoang ka ntle ea overcurrent | 10 A mofuta oa B circuit breaker (EU) 13 Mofuta oa B oa potoloho ea potoloho (Sweden) |
| Bakeng sa ho kenya mabokoseng | Ø = 60 mm, botebo ≥ 60 mm |
| Lithapo tse khothalelitsoeng | Sebaka se pakeng tsa 0.75-1.5 mm2 se hlobotse 8 - 9 mm ea ho pata |
| Mocheso oa ho sebetsa | 0 – 35°C |
| Mongobo wa tikoloho | 10 - 95% RH ntle le condensation |
| Radio protocol | Z-Wave (800 series chip) |
| Sehlopha sa maqhubu a seea-le-moea | EU: 868.4 MHz, 869.85 MHz AH: 919.8 MHz, 921.4 MHz |
| Boholo. matla a fetisang | +6dBm |
| Range | ho fihla ho 100 m ka ntle ho fihla ho 30 m ka tlung (ho ipapisitse le sebaka le sebopeho sa moaho) |
| Litekanyo (bolelele x bophara x botebo) | 46 × 36 × 19.9 limilimithara |
| Ho latela litaelo tsa EU | RoHS 2011/65 / EU RED 2014/53 / EU |
Hlokomela
Maqhubu a seea-le-moea a sesebelisoa ka bomong a hloka ho tšoana le molaoli oa hau oa Z-Wave. Sheba lintlha tse lebokoseng kapa u botse morekisi oa hau haeba o sa tiisehe.
KEKETSO
Pele ho instola
Ho kopanya sesebelisoa ka mokhoa o sa lumellaneng le bukana ena ho ka baka kotsi ho bophelo bo botle, bophelo kapa tšenyo ea thepa.
- Se ke oa matlafatsa sesebelisoa pele u se kopanya ka botlalo ka lebokoseng la ho kenya.
- Hokela feela ho latela litšoantšo tse ka tlase.
- Kenya feela ka har'a mabokose a phahamisoang a tsamaisanang le litekanyetso tse amehang tsa polokeho ea naha le botebo bo seng ka tlase ho 60 mm.
- Se ke oa hokela lisebelisoa tse sa tsamaellaneng le lintlha kapa maemo a ts'ireletso a amehang.
- Se ke oa hokela lisebelisoa tsa ho futhumatsa.
- Se ke oa hokela li-circuits tsa SELV kapa tsa PELV.
- Etsa bonnete ba hore li-switches tsa motlakase tse sebelisoang ha ho kengoa li lumellana le litekanyetso tse nepahetseng tsa polokeho.
- Etsa bonnete ba hore bolelele ba lithapo tse sebelisoang ho hokahanya sesebelisoa sa taolo ha boa lokela ho feta 20 m.
- Hokela li-roller blind AC motors tse nang le li-switch tsa elektroniki kapa tsa mochini feela.
Lintlha tsa Setšoantšo sa 1:
- O1 - setsi sa pele sa tlhahiso bakeng sa enjene ea shutter
- O2 - terminal ea 2nd ea tlhahiso bakeng sa enjene ea shutter
- S1 - terminal bakeng sa switch ea pele (e boetse e sebelisetsoa ho eketsa / ho tlosa sesebelisoa)
- S2 - terminal bakeng sa switch ea 2nd (e boetse e sebelisetsoa ho eketsa / ho tlosa sesebelisoa)
- N - li-terminals tsa lead lead (tse hokahaneng ka hare)
- L - li-terminals bakeng sa lead lead (e hokahane ka hare)
- PROG - konopo ea ts'ebeletso (e sebelisetsoang ho eketsa / ho tlosa sesebelisoa le ho tsamaisa menu)
Tlhokomeliso!
Litaelo tse nepahetseng tsa lithapo le litataiso tsa ho tlosa likhoele
Kenya lithapo FEELA sekoting sa theminale sa sesebelisoa. Ho tlosa lithapo life kapa life, tobetsa konopo ea tokollo, e holim'a sekotjana.
Ho kenya
- Tlosa lisebelisoa tsa motlakase voltage (thibela fuse).
- Bula lebota la switjha lebokose.
- Hokela ho latela Setšoantšo sa 2 ka ho le letona.
- Netefatsa haeba sesebelisoa se hokahane ka nepo.
- Lokisetsa sesebelisoa ka lebokoseng la ho fetola lebota.
- Koala lebota la switjha lebokose.
- Fetolela li-mains voltage.
Lintlha
- Ho hokahanya li-switches tsa lebota la kantle sebelisa lithapo tsa jumper tse fanoeng ha ho hlokahala.
- Haeba u sebelisa sesebelisoa sa Yubii Home, ha ua tlameha ho tšoenyeha ka ho hokahanya litsela ka nepo. U ka fetola litsela ho li-setting tsa wizate le sesebelisoa ho app mobile.
Tlhokomeliso
Lithapo tsa jumper tse fanoeng li ka sebelisoa feela ho hokahanya li-switches tsa lebota. Sebelisa thapo e loketseng ea ho kenya ho tsamaisa motlakase oa sesebelisoa. Likarolo tse ling tsa ho kenya (borokho) le tsona li hloka ho hokeloa ka thapo e loketseng ea ho kenya. Haeba ho hlokahala, sebelisa sehokelo se loketseng sa lithapo tsa motlakase.
KEKELETSO NETEBELETSO EA Z-WAVE
Ho eketsa (Kenyelletso) - mokhoa oa ho ithuta oa sesebelisoa sa Z-Wave o u nolofalletsang ho eketsa sesebelisoa ho marang-rang a teng a Z-Wave.
Ho eketsa ka letsoho
Ho eketsa sesebelisoa ho netweke ea Z-Wave ka letsoho:
- Matla sesebelisoa. Haeba sesebelisoa se sa kengoa marang-rang a Z-Wave, sesebelisoa sa LED se benya bofubelu.
- Beha molaoli ea ka sehloohong ho (Tshireletso / e seng Tšireletseho) mokhoa oa ho eketsa (bakeng sa boitsebiso bo eketsehileng, bona buka ea molaoli).
- Ka potlako, tobetsa konopo ea PROG sesebelisoa ka makhetlo a mararo. Ntle le moo, tobetsa kapele S1 kapa S2 makhetlo a mararo.
- Haeba o eketsa sesebelisoa ka mokhoa o netefalitsoeng oa S2, kenya PIN Code, e ngotsoeng ho sesebelisoa. PIN Code hape ke karolo e thathamisitsoeng ea konopo e khethehileng ea sesebelisoa (DSK) e ngotsoeng botlaaseng ba lebokose.
- Emela hore letšoao la LED le benyebe ka mosehla.
- Keketso e atlehileng e netefatsoa ke molaetsa oa molaoli oa Z-Wave le sesebelisoa sa LED:
Botala - e atlehileng (e sa sireletsehang, S0, S2 e sa netefatsoa)
Magenta - e atlehile (Security S2 E netefalitsoe)
Khubedu – ha e atlehe
Ho eketsa ka ho sebelisa SmartStart
Tharollo ea SmartStart e nolofalletsa lihlahisoa ho eketsoa marang-rang a Z-Wave ka ho skena Khoutu ea Z-Wave QR e teng sehlahisoa ka molaoli ea fanang ka kenyelletso ea SmartStart. Sehlahisoa sa SmartStart se eketsoa ka bohona nakong ea metsotso e 10 ka mor'a ho bulela marang-rang.
Ho eketsa sesebelisoa ho netweke ea Z-Wave u sebelisa SmartStart:
- Ho sebelisa tharollo ea SmartStart molaoli oa hau o hloka ho ts'ehetsa mokhoa oa Security S2 (bakeng sa tlhaiso-leseling e batsi, sheba bukana ea taolo).
- Kenya khoele e felletseng ea DSK ho molaoli oa hau. Haeba molaoli oa hau a khona ho hlahloba QR, hlahloba khoutu ea QR e behiloeng leiboleng.
- Matlafatsa sesebediswa (bulela mains voltagle).
- Letšoao la LED le qala ho benya mosehla, emela hore ts'ebetso ea ho eketsa e fele.
- Keketso e atlehileng e netefatsoa ke molaetsa oa molaoli oa Z-Wave le sesebelisoa sa LED:
Botala - e atlehileng (e sa sireletsehang, S0, S2 mokhoa o sa netefatsoang),
Magenta - e atlehile (Mokhoa o netefalitsoeng oa S2),
Khubedu – ha e atlehe
Hlokomela
Haeba ho na le mathata ka ho eketsa sesebelisoa, ka kopo, seta sesebelisoa hape 'me u phete mokhoa oa ho eketsa.
HO TLOSA NETEKENG EA Z-WAVE
Ho tlosa (Ho qheleloa ka thoko) - Mokhoa oa ho ithuta oa sesebelisoa sa Z-Wave o u nolofalletsang ho tlosa sesebelisoa ho netweke e teng ea Z-Wave.
Ho tlosa sesebelisoa marangrang a Z-Wave:
- Etsa bonnete ba hore sesebelisoa se sebelisoa.
- Beha molaoli ea ka sehloohong ka mokhoa oa ho tlosa (bakeng sa boitsebiso bo eketsehileng, bona buka ea molaoli).
- Ka potlako, tobetsa konopo ea PROG ka makhetlo a mararo. Ntle le moo, tobetsa kapele S1 kapa S2 makhetlo a mararo nakong ea metsotso e 10 ka mor'a ho matlafatsa sesebelisoa.
- Emela hore ts'ebetso e tlosoe.
- Ho tlosa ka katleho ho netefatsoa ke molaetsa oa molaoli oa Z-Wave.
- Letšoao la LED la sesebelisoa le khanya bofubelu.
Hlokomela
Ho tlosa sesebelisoa marang-rang a Z-Wave ha ho etse hore fektheri e qale ho tsosolosa.
TS'IRELETSO
Calibration ke ts'ebetso eo ka eona sesebelisoa se ithutang boemo ba li-switches tsa moeli le tšobotsi ea motlakase. Calibration ke ntho e tlamang hore sesebelisoa se tsebe hantle boemo ba bofofu ba rolara. Ts'ebetso e na le motsamao o felletseng oa othomathike, lipakeng tsa li-switches tsa moeli (metsamao e 'maloa ea ho ea holimo/tlase).
Calibration ka othomathiki ka ho sebelisa menu
- Tobetsa 'me u tšoare konopo ea PROG ho kenya menu.
- Konopo ea ho lokolla ha sesebelisoa se khanya seputsoa (boemo ba pele).
- Tobetsa konopo kapele ho netefatsa.
- Sesebelisoa se etsa ts'ebetso ea ho lekanya, ho phethela potoloho e felletseng - metsamao e 'maloa ea holimo le tlase. Nakong ea ho lekanya LED e benya boputsoa.
- Haeba calibration e atlehile, letšoao la LED le khanyetsa botala. Haeba calibration e hloleha, letšoao la LED le khanya bofubelu.
- Lekola hore na boemo bo sebetsa hantle.
Calibration e iketsang e sebelisa paramethara
- Beha parameter ea 150 ho isa ho 3.
- Sesebelisoa se etsa ts'ebetso ea ho lekanya, ho phethela potoloho e felletseng - metsamao e 'maloa ea holimo le tlase. Nakong ea ho lekanya letšoao la LED le benya boputsoa.
- Haeba calibration e atlehile, letšoao la LED le khanyetsa botala. Haeba calibration e hloleha, letšoao la LED le khanya bofubelu.
- Lekola hore na boemo bo sebetsa hantle.
Lintlha:
- Haeba u sebelisa Yubii Home App, u ka khona ho lekanya ho tsoa ho wizate kapa ho li-setting tsa sesebelisoa.
- Mokhoa oa ho lekanya o ka sebetsa betere ha o beha sefofu sebakeng se bulehileng se bohareng pele o qala.
- O ka emisa ts'ebetso ea ho lekanya nako efe kapa efe ka ho tobetsa konopo ea PROG kapa linotlolo tsa kantle.
- Litšobotsi tsa motlakase tsa li-motors li ka fapana, tse ka bakang ho hloleha ha calibration. Ho lokisa bothata boo u ka:
- Eketsa boleng ba paramethara 154, mohlala ho isa ho metsotsoana e 5 pele u leka ho etsa calibration hape.
- Haeba tlhahlobo e ntse e sa atlehe, fokotsa boleng ba paramethara ho tloha ho 155 ho isa ho 1 W pele u leka ho lekanya hape.
- Haeba mehato ea 1 le ea 2 e hlolehile, beha paramethara 155 ho isa ho 0 'me u sebelise liparamente 156 le 157 ho ipehela nako ea motsamao ka letsoho. Ka mor'a ho beha nako ka letsoho ho hlokahala hore u tsamaise shutter ea rolara libakeng tse peli tsa ho qetela (tse bulehileng ka ho feletseng le tse koetsoeng ka ho feletseng) e le hore mojule o ka sebelisa nako e hlalositsoeng ea ho sisinyeha.
Ho beha li-slats ka letsoho ka mokhoa oa lifofu tsa venetian
- Beha parameter 151 ho 1 (0-90 °) kapa 2 (0-180 °), ho itšetlehile ka bokhoni ba ho potoloha ha li-slats.
- Ka ho feletseng, parameter 152 e behiloe ho 15, e bolelang hore nako ea phetoho pakeng tsa maemo a ho qetela e lekana le metsotsoana e 1.5.
- Fetola li-slats pakeng tsa maemo a ho qetela ka ho tšoara
konopo:
- Haeba ka mor'a potoloho e feletseng sefofu se qala ho ea holimo kapa tlaase - fokotsa boleng ba parameter 152.
- Haeba kamora potoloho e felletseng li-slats li sa fihle maemong a ho qetela - eketsa boleng ba paramente 152.
- Pheta mohato o fetileng ho fihlela boemo bo khotsofatsang bo finyelloa.
- Lekola hore na boemo bo sebetsa hantle. Li-slats tse hlophisitsoeng hantle ha lia lokela ho qobella lifofu ho ea holimo kapa tlase.
TS'EBELETSO SETS'OANE
Sesebelisoa se nolofalletsa ho hokahanya ha li-terminals tsa S1 le S2. Tsena e ka ba li-switches tse monostable kapa bistable. Likonopo tsa switjha li na le boikarabello ba ho laola motsamao o foufetseng.
Tlhaloso:
- Fetolela hokahane le terminal ea S1
- Fetolela hokahane le terminal ea S2
Malebela a akaretsang:
- O ka qala, oa emisa, kapa oa fetola tsela eo u tsamaeang ka eona u sebelisa switch kapa switch
- Haeba u beha khetho ea ts'ireletso ea lipitsa tsa lipalesa, ts'ebetso ea ho theola e etsoa feela ka mokhoa o hlalositsoeng.
- Haeba u laola feela sebaka se foufetseng sa venetian (eseng slats rotation) li-slats li khutlela sebakeng sa tsona sa pele (ka tekanyo ea ho bula 0 - 95%).
Li-switches tsa monostable - tobetsa ho tsamaisa
Exampsebopeho sa switch:
| Letlapa la A2 - Roll-Control2 - Li-switches tse bonolo - tobetsa ho tsamaisa | |
| Paramethara: | 20. Mofuta oa phetoho |
| Tlhaloso: | Paramethara ena e etsa qeto ea hore na ke mefuta efe ea li-switches le mekhoa ea S1 le S2 e sebetsang ka eona. |
| Beha boleng: | 0 - Li-switches tse monostable - tobetsa ho tsamaisa |
| Paramethara: | 151. Roller blind, Awning, Pergola kapa Curtain |
| Tlhaloso: | 1× tlanya switjha – Ho qala ho sisinyeha ho ya sebakeng se lekanyeditsweng Tlanya e latelang - emisa 1× tlanya switjha – Ho qala motsamao o theohang ho ya sebakeng se lekanyeditsweng2× tlanya switjha – Sebaka seo o se ratangTšoara - Phahamisa ho fihlela ho lokolloaTšoara - Ho theosa ho fihlela ho lokolloa |
| E fumaneha boleng: | 0 |
| Paramethara: | 151. Sefofu sa Venetian |
| Tlhaloso: | 1× tlanya switjha – Ho qala ho sisinyeha ho ya sebakeng se lekanyeditsweng Tlanya e latelang - fallela sebakeng se nepahetseng 1× tlanya switjha – Ho qala motsamao o theohang ho ya sebakeng se lekanyeditsweng2× tlanya switjha – Sebaka seo o se ratangTšoara - Ho phahamisa li-slats ho fihlela ho lokolloaTšoara - Ho theola li-slats ho fihlela ho lokolloa |
| E fumaneha boleng: | 1 kapa 2 |
Sebaka seo u se ratang - se teng
Li-switches tsa monostable - tšoara ho tsamaea
Exampsebopeho sa switch:
| Letlapa la A3 - Roll-Control2 - Li-switches tse tšoarellang - tšoara ho sisinyeha | |
| Paramethara: | 20. Mofuta oa phetoho |
| Tlhaloso: | Paramethara ena e etsa qeto ea hore na ke mefuta efe ea li-switches le mekhoa ea S1 le S2 e sebetsang ka eona. |
| Beha boleng: | 1 - Li-switches tse monostable - tšoara ho tsamaea |
| Paramethara: | 151. Roller blind, Awning, Pergola kapa Curtain |
| Tlhaloso: | 1× tlanya switjha - 10% ho nyoloha motsamao 1× tlanya switjha - 10% ho theosa le motsamao2× tlanya switjha – Sebaka seo o se ratangTšoara - Phahamisa ho fihlela ho lokolloaTšoara - Ho theosa ho fihlela ho lokolloa |
| E fumaneha boleng: | 0 |
| Paramethara: | 151. Sefofu sa Venetian |
| Tlhaloso: | 1× tlanya switjha - Li-slats li potoloha holimo ka mohato o boletsoeng esale pele 1× tlanya switjha - Slats e potoloha ho ea tlase ka mohato o boletsoeng esale pele2× tlanya switjha – Sebaka seo o se ratangTšoara - Phahamisa ho fihlela ho lokolloaTšoara - Ho theosa ho fihlela ho lokolloa |
| E fumaneha boleng: | 1 kapa 2 |
Sebaka seo u se ratang - se teng
Haeba u tšoara switch nako e telele ho feta nako ea ho sisinyeha ha li-slats + metsotsoana e meng ea 4 (kamehla 1,5s + 4s = 5,5s) sesebelisoa se tla ea sebakeng se lekanyelitsoeng. Tabeng eo ho lokolla switjha ho ke ke ha etsa letho.
Phetoho e le 'ngoe ea monostable
Exampsebopeho sa switch:
| Letlapa la A4 - Roll-Control2 - switch e le 'ngoe e le 'ngoe | |
| Paramethara: | 20. Mofuta oa phetoho |
| Tlhaloso: | Paramethara ena e etsa qeto ea hore na ke mefuta efe ea li-switches le mekhoa ea S1 le S2 e sebetsang ka eona. |
| Beha boleng: | 2 - Sesebelisoa se le seng se le seng |
| Paramethara: | 151. Roller blind, Awning, Pergola kapa Curtain |
| Tlhaloso: | 1× tobetsa - Qala motsamao ho ea sebakeng se lekanyelitsoeng Tlanya e latelang - emisa Tlanya hape - Qala ho sisinyeha ho ea sebakeng se fapaneng sa moeli 2× tobetsa - Sebaka seo u se ratang Tšoara - Qala motsamao ho fihlela o lokolloa |
| E fumaneha boleng: | 0 |
| Paramethara: | 151. Sefofu sa Venetian |
| Tlhaloso: | 1× tobetsa - Qala motsamao ho ea sebakeng se lekanyelitsoeng Tlanya e latelang - emisa Tlanya hape - Qala ho sisinyeha ho ea sebakeng se fapaneng sa moeli 2× tobetsa - Sebaka seo u se ratang Tšoara - Qala motsamao ho fihlela o lokolloa |
| E fumaneha boleng: | 1 kapa 2 |
Sebaka seo u se ratang - se teng
Li-switches tsa Bistabile
Exampsebopeho sa switch:
| Letlapa la A5 - Roll-Control2 - Li-switches tsa Bistabile | |
| Paramethara: | 20. Mofuta oa phetoho |
| Tlhaloso: | Paramethara ena e etsa qeto ea hore na ke mefuta efe ea li-switches le mekhoa ea S1 le S2 e sebetsang ka eona. |
| Beha boleng: | 3 - Li-switches tsa Bistable |
| Paramethara: | 151. Roller blind, Awning, Pergola kapa Curtain |
| Tlhaloso: | 1 × tobetsa (potoloho e koetsoe) - Qala ho sisinyeha ho ea sebakeng sa moeli E latelang tobetsa e tšoanang - Emisa switch e tšoanang (mokoloko o butsoe) |
| E fumaneha boleng: | 0 |
| Paramethara: | 151. Sefofu sa Venetian |
| Tlhaloso: | 1 × tobetsa (potoloho e koetsoe) - Qala ho sisinyeha ho ea sebakeng sa moeli E latelang tobetsa e tšoanang - Emisa switch e tšoanang (mokoloko o butsoe) |
| E fumaneha boleng: | 1 kapa 2 |
Sebaka seo u se ratang - ha se fumanehe
Phetoho e le 'ngoe ea bistabile
Exampsebopeho sa switch:
| Tafole ea A6 - Roll-Control2 - switch e le 'ngoe ea bistable | |
| Paramethara: | 20. Mofuta oa phetoho |
| Tlhaloso: | Paramethara ena e etsa qeto ea hore na ke mefuta efe ea li-switches le mekhoa ea S1 le S2 e sebetsang ka eona. |
| Beha boleng: | 4 - Switjha e le 'ngoe ea bistable |
| Paramethara: | 151. Roller blind, Awning, Pergola kapa Curtain |
| Tlhaloso: | 1× tobetsa - Qala motsamao ho ea sebakeng se lekanyelitsoeng Tlanya e latelang - emisa Tlanya hape - Qala ho sisinyeha ho ea sebakeng se fapaneng sa moeli Tlanya e latelang - emisa |
| E fumaneha boleng: | 0 |
| Paramethara: | 151. Sefofu sa Venetian |
| Tlhaloso: | 1× tobetsa - Qala motsamao ho ea sebakeng se lekanyelitsoeng Tlanya e latelang - emisa Tlanya hape - Qala ho sisinyeha ho ea sebakeng se fapaneng sa moeli Tlanya e latelang - emisa |
| E fumaneha boleng: | 1 kapa 2 |
Sebaka seo u se ratang - ha se fumanehe
Phetoho ea linaha tse tharo
Exampsebopeho sa switch:
| Letlapa la A7 - Roll-Control2 - switch ea linaha tse tharo | |
| Paramethara: | 20. Mofuta oa phetoho |
| Tlhaloso: | Paramethara ena e etsa qeto ea hore na ke mefuta efe ea li-switches le mekhoa ea S1 le S2 e sebetsang ka eona. |
| Beha boleng: | 5 |
| Paramethara: | 151. Roller blind, Awning, Pergola kapa Curtain |
| Tlhaloso: | 1× tobetsa - Qala ho sisinyeha ho ea sebakeng se lekanyelitsoeng ka tsela e khethiloeng ho fihlela sesebelisoa se khetha taelo ea ho emisa |
| E fumaneha boleng: | 0 |
| Paramethara: | 151. Sefofu sa Venetian |
| Tlhaloso: | 1× tobetsa - Qala ho sisinyeha ho ea sebakeng se lekanyelitsoeng ka tsela e khethiloeng ho fihlela sesebelisoa se khetha taelo ea ho emisa |
| E fumaneha boleng: | 1 kapa 2 |
Sebaka seo u se ratang - ha se fumanehe
Boemo bo ratileng
Sesebelisoa sa hau se na le mochini o hahelletsoeng kahare oa ho seta maemo ao u a ratang.
U ka e kenya tšebetsong ka ho tobetsa habeli ho (monostable switch(es)) e hokahantsoeng le sesebelisoa kapa ho tsoa ho mobile interface (mobile app).
Favourite roller blind position
U ka hlalosa boemo boo u bo ratang ba lifofu. E ka behoa ka parameter 159. Boleng ba kamehla bo behiloe ho 50%.
Sebaka seo u se ratang ka li-slats
U ka hlalosa boemo boo u bo ratang ba angle ea slats. E ka behoa ka parameter 160. Boleng ba kamehla bo behiloe ho 50%.
Tšireletso ea pitsa
Sesebelisoa sa hau se na le mochini o hahelletsoeng kahare ho o sireletsa, mohlalaample, lipalesa fensetereng. Sena ke se bitsoang "virtual limit switch". O ka beha boleng ba eona ho parameter 158. Ntho e sa lekanyetsoang ke 0 - sena se bolela hore sefofu sa rolara se tsamaea pakeng tsa maemo a phahameng a ho qetela.
Lipontšo tsa LED
LED e hahiloeng e bontša boemo ba hona joale ba sesebelisoa ha sesebelisoa se tsamaisoa.
| Letlapa la A8 - Roll-Control2 - mebala ea LED le moelelo oa eona | |
| Mmala | Tlhaloso |
| Botala | Sesebelisoa se kentsoe marang-rang a Z-Wave (e sa sireletsehang, S0, S2 ha e netefatsoe) |
| Magenta | Sesebelisoa se kentsoe marang-rang a Z-Wave (Security S2 E netefalitsoe) |
| Khubedu | Sesebelisoa ha se eketsoe marang-rang a Z-Wave |
| 'Cyan e panyang | Ntlafatso e ntse e tsoela pele |
U sebelisa lethathamo la lisebelisoa tse hahelletsoeng kahare, u ka khona ho lekanya sesebelisoa kapa ua etsa reset ea fektheri.
Ho sebelisa menu ea sesebelisoa se hahelletsoeng ka hare:
- Tlosa lisebelisoa tsa motlakase voltage (thibela fuse).
- Tlosa sesebelisoa lebokoseng la ho fetola lebota.
- Fetolela li-mains voltage.
- Tobetsa 'me u tšoare konopo ea PROG ho kenya menu.
- Emela letšoao la LED ho bonts'a sebaka sa menu se lakatsehang ka 'mala:
- PUTSOA - autocalibration
- YELLOW - reset ea fektheri
- E lokolle kapele ebe o tobetsa konopo ea PROG hape.
- Kamora ho tobetsa konopo ea PROG, letšoao la LED le tiisa boemo ba menyu ka ho panya.
HO SIRELETSA LITLHAKISO TSA FEKE
Ts'ebetso ea ho seta bocha e u thusa ho khutlisetsa sesebelisoa ho litlhophiso tsa feme, ho bolelang hore tlhaiso-leseling eohle e mabapi le molaoli oa Z-Wave le tlhophiso ea mosebelisi e tla hlakoloa.
Ka kopo sebelisa mokhoa ona feela ha molaoli oa mantlha oa marang-rang a le sieo kapa ho seng joalo a sa sebetse.
- Tlosa lisebelisoa tsa motlakase voltage (thibela fuse).
- Tlosa sesebelisoa lebokoseng la ho fetola lebota.
- Fetolela li-mains voltage.
- Tobetsa 'me u tšoare konopo ea PROG ho kenya menu.
- Emela hore letšoao la LED le khanye mosehla.
- E lokolle kapele ebe o tobetsa konopo ea PROG hape.
- Nakong ea ho tsosolosa fektheri, letšoao la LED le benya mosehla.
- Ka mor'a metsotsoana e seng mekae sesebelisoa se tsosolosoa, se bontšitsoeng ka 'mala o mofubelu oa letšoao la LED.
MOTLATSI METIRI
Sesebelisoa se thusa ho beha leihlo tšebeliso ea matla. Roll-Control2 e tlaleha tšebeliso ea matla, empa ha e tlalehe matla a hang-hang. Lintlha li romelloa ho molaoli ea ka sehloohong oa Z-Wave.
Ho lekanya ho etsoa ke theknoloji e tsoetseng pele ka ho fetisisa ea "micro-controller", e netefatsang ho nepahala le ho nepahala ho fetisisa (+/- 5% bakeng sa meroalo e kholo ho feta 10 W).
Matla a motlakase - matla a sebelisoang ke sesebelisoa ka nako e itseng. Basebelisi ba motlakase malapeng ba lefisoa ke bafani ba thepa ho latela matla a sebetsang a sebelisoang nakong e fanoeng. Hangata e lekanngoa ka kilowatt-hora [kWh]. Kilowatt-hora e le 'ngoe e lekana le kilowatt e le' ngoe ea matla a sebelisoang nakong ea hora e le 'ngoe, 1 kWh = 1000 Wh.
Ho tsosolosa memori ea tšebeliso:
Reset ea memori ea tšebeliso e ka qalisoa ka sebopeho sa hub (BUI) kapa molaoli oa Z-Wave o sebelisa Meter CC. Ts'ebetso ea memori ea ts'ebeliso e boetse e etsoa nakong ea ts'ebetso ea ho seta feme.
TIISETSO
Mokhatlo (o hokahanya lisebelisoa) - taolo e otlolohileng ea lisebelisoa tse ling ka har'a netweke ea sistimi ea Z-Wave.
Mekhatlo e thusa:
- Ho tlaleha boemo ba sesebelisoa ho molaoli oa Z-Wave (ho sebelisa sehlopha sa Lifeline).
- Ho theha li-automation tse bonolo ka ho laola lisebelisoa tse ling ntle le ho kenya letsoho ha molaoli ea ka sehloohong (ho sebelisa lihlopha tse abetsoeng liketso ho sesebelisoa).
- Litaelo tse romelloang ho sehlopha sa 2nd li bonts'a ts'ebetso ea konopo ho latela ts'ebetso ea sesebelisoa, mohlala, ho qala motsamao oa lifofu u sebelisa konopo ho romella foreimi e ikarabellang bakeng sa ketso e tšoanang.
Sesebelisoa se fana ka mokhatlo oa lihlopha tse 2:
- Sehlopha sa 1 sa mokhatlo - "Lifeline" e tlaleha boemo ba sesebelisoa mme e lumella ho fana ka sesebelisoa se le seng feela (molaoli ea ka sehloohong ka ho sa feleng).
- Sehlopha sa 2nd association - "Window Covering" e reretsoe likharetene kapa lifofu tse lumellang mosebedisi ho laola boholo ba khanya e kenang lifensetereng.
Sesebelisoa se nolofalletsa ho laola lisebelisoa tsa 5 tse tloaelehileng kapa tse ngata ho sehlopha sa mokhatlo, ntle le sehlopha sa Lifeline se boloketsoeng feela molaoli 'me kahoo ke node ea 1 feela e ka abeloang.
Ho eketsa mokhatlo:
- Eya ho Litlhophiso
. - Eya ho Lisebelisoa.
- Khetha sesebelisoa se loketseng lethathamong.
- Khetha tab ea Mekhatlo.
- Hlalosa sehlopha le lisebelisoa tseo u ka ikamahanyang le tsona.
- Boloka liphetoho tsa hau.
| Letlapa la A9 - Roll-Control2 - Lihlopha tsa Taelo le Litaelo | |||
| Sehlopha | Profile | Sehlopha sa Taelo le Taelo | Lebitso la Sehlopha |
| 1 | Kakaretso: Lifeline (0x00: 0x01) | COMMAND_CLASS_DEVICE_RESET_LOCALLY [0x5A] | Lifeline |
| DEVICE_RESET_LOCALLY_NOTIFICATION [0x01] | |||
| COMMAND_CLASS_WINDOW_COVERING [0x6A] | |||
| WINDOW_COVERING_REPORT [0x04] | |||
| COMMAND_CLASS_SWITCH_MULTILEVEL [0x26] | |||
| SWITCH_MULTILEVEL_REPORT [0x26] | |||
| COMMAND_CLASS_METER [0x32] | |||
| METER_REPORT [0x02] | |||
| COMMAND_CLASS_NOTIFICATION [0x71] | |||
| NOTIFICATION_REPORT [0x05] | |||
| COMMAND_CLASS_CENTRAL_SCENE [0x5B] | |||
| CENTRAL_SCENE_NOTIFICATION [0x03] | |||
| COMMAND_CLASS_CONFIGURATION [0x70] | |||
| CONFIGURATION_REPORT [0x06] | |||
| 2 | Taolo: KEY01 (0x20: 0x01) | COMMAND_CLASS_WINDOW_COVERING [0x6A] | Ho koahela fensetere |
| WINDOW_COVERING_SET [0x05] | |||
| COMMAND_CLASS_WINDOW_COVERING [0x6A] | |||
| WINDOW_COVERING_START_LEVEL_CHANGE [0x06] | |||
| COMMAND_CLASS_WINDOW_COVERING [0x6A] | |||
| WINDOW_COVERING_STOP_LEVEL_CHANGE [0x07] | |||
| Letlapa la A10 - Roll-Control2 - Sehlopha sa Mokhatlo 2: Fensetere e koahelang boemo ba ho lekanya le boleng ba Id ea taelo | ||||
| Id | Boemo ba ho lekanya | Lebitso le koahelang fensetere | ID ea Sekoaelo sa Lifensetere | |
| Id_Roller | 0 | Sesebelisoa ha sea lokisoa | HO TSOA_TLASE_1 | EA-12 (0x0C) |
| 1 | Autocalibration e atlehile | HO TSOA_ TLAS'A _2 | 13 (0x0D) | |
| 2 | Autocalibration e hlolehile | HO TSOA_TLASE_1 | EA-12 (0x0C) | |
| 4 | Tekanyetso ka letsoho | HO TSOA_ TLAS'A _2 | 13 (0x0D) | |
| Id_Slats | 0 | Sesebelisoa ha sea lokisoa | HORIZONTAL_SLATS_ANGLE_1 | EA-22 (0x16) |
| 1 | Autocalibration e atlehile | HORIZONTAL_SLATS_ANGLE_2 | EA-23 (0x17) | |
| 2 | Autocalibration e hlolehile | HORIZONTAL_SLATS_ANGLE_1 | EA-22 (0x16) | |
| 4 | Tekanyetso ka letsoho | HORIZONTAL_SLATS_ANGLE_2 | EA-23 (0x17) | |
| Letlapa la A11 - Roll-Control2 - Mokhoa oa ho sebetsa: Roller blind, Awning, Pergola, Curtain; Sefofu sa Venetian 90 °; Sefofu sa Venetian 180 ° | |||||||
| Parametr 20 - Mofuta oa phetoho | Fetoha | Tobetsa ha 'ngoe | Penya Habeli | ||||
| Boleng | Lebitso | S1 kapa S2 | Taelo | ID | Taelo | ID | |
| 0 | Li-switches tsa monostable - tobetsa ho tsamaisa | Fesetere e Koahelang Phetoho ea Boemo ba ho Qala Fesetere e Koahelang Stop Stop Level Phetoho |
Id_Roller | Fesetere Covering Set Level | Id_Roller Id_Slats | ||
| 1 | Li-switches tsa monostable - tšoara ho tsamaea | Fesetere e Koahelang Fesetere Seta Phetoho ea Boemo | Id_Roller Id_Slats |
||||
| 2 | Phetoho e le 'ngoe ea monostable | Fesetere e Koahelang Phetoho ea Boemo ba ho Qala Fesetere e Koahelang Stop Stop Level Phetoho |
Id_Roller | ||||
| 3 | Li-switches tsa Bistable | Id_Roller | – | – | |||
| 5 | Phetoho ea linaha tse tharo | Id_Roller | – | – | |||
| Parametr 20 - Mofuta oa phetoho | Fetoha | Tšoara | Lokolla | ||||
| Boleng | Lebitso | S1 kapa S2 | Taelo | ID | Taelo | ID | |
| 0 | Li-switches tsa monostable - tobetsa ho tsamaisa | Fesetere e Koahelang Phetoho ea Boemo ba ho Qala Fesetere e Koahelang Stop Stop Level Phetoho |
Id_Slats | Fesetere e Koahelang Stop Stop Level Phetoho | Id_Slats | ||
| 1 | Li-switches tsa monostable - tšoara ho tsamaea | Id_Roller | Id_Roller | ||||
| 2 | Phetoho e le 'ngoe ea monostable | Id_Slats | Id_Slats | ||||
| 3 | Li-switches tsa Bistable | – | – | – | – | ||
| 5 | Phetoho ea linaha tse tharo | – | – | – | – | ||
| Parameter 20 - Mofuta oa phetoho | Fetoha | Fetola boemo ha rolara e sa sisinyehe | Fetola boemo ha rolara e ntse e tsamaea | ||||
| Boleng | Lebitso |
S1 kapa S2 |
Taelo | ID | Taelo | ID | |
| 4 | Phetoho e le 'ngoe ea bistable | Fesetere e Koahelang Phetoho ea Boemo ba ho Qala | Id_Roller | Fesetere e Koahelang Stop Stop Level Phetoho | Id_Roller | ||
Hlokomela
Id_Slats e amana feela le parameter 151 e behiloeng ho boleng ba 1 kapa 2.
TS'OANELO MPHATO
Sesebediswa se nolofalletsa ho etsa tshebetso ya sona ho ya ka ditlhoko tsa mosebedisi ho sebedisa diparamente tse ka lokisehang. Litlhophiso li ka fetoloa ho sebelisoa molaoli oa Z-Wave eo sesebelisoa se eketsoang ho eona. Mokhoa oa ho li lokisa o ka fapana ho ea ka molaoli. Sebopeho sa sesebelisoa sa sebopeho sa NICE se fumaneha e le sete e bonolo ea likhetho karolong ea Advanced Settings. Haeba u sebelisa sesebelisoa sa Yubii Home, litlhophiso tse ngata tse latelang li ka fetoloa karolong ea litlhophiso tsa sesebelisoa.
Ho lokisa sesebelisoa:
- Eya ho Litlhophiso .
- Eya ho Lisebelisoa.
- Khetha sesebelisoa se loketseng lethathamong.
- Khetha tab ea Parameters.
- Fetola litlhophiso tse nepahetseng kapa boleng.
- Boloka liphetoho tsa hau.
| Letlapa la A12 - Roll-Control2 - Litekanyetso tse tsoetseng pele | ||||
| Paramethara | Tlhaloso | Boholo | Boleng ba kamehla | E fumaneha Litekanyetso |
| 20 - Mofuta oa phetoho | Paramethara ena e etsa qeto ea hore na ke mefuta efe ea li-switches le mekhoa ea S1 le S2 e sebetsang ka eona. | 1 [byte] | 0 (boleng ba kamehla) | 0 - Li-switches tse monostable - tobetsa ho tsamaisa 1 - Li-switches tse monostable - tšoara ho tsamaea 2 - Sesebelisoa se le seng se le seng 3 - Li-switches tsa Bistable 4 - Switjha e le 'ngoe ea bistable 5 - Phetoho ea linaha tse tharo |
| 24 - Likonopo tse mabapi | Paramethara ena e thusa ho khutlisa ts'ebetso ea likonopo. | 1 [byte] | 0 (boleng ba kamehla) | 0 - ea kamehla (konopo ea pele UP, konopo ea 1 DOWN) 1 - e khutliselitsoe morao (konopo ea 1 HO TLOHA, konopo ea 2 UP) |
| 25 – Maikutlo a lipoelo | Paramethara ena e thusa ho khutlisa ts'ebetso ea O1 le O2 ntle le ho fetola mohala (mohlala, haeba ho na le khokahano e fosahetseng ea enjene). | 1 [byte] | 0 (boleng ba kamehla) | 0 - ea kamehla (O1 - UP, O2 - DOWN) 1 - e khutliselitsoe morao (O1 - DOWN, O2 - UP) |
| 40 - Konopo ea pele - litšoantšo li rometsoe | Paramethara ena e etsa qeto ea hore na ke liketso life tse tla fella ka ho romela li-ID tsa ketsahalo tseo ba li abetsoeng. Boleng bo ka kopanngwa (mohlala, 1+2=3 e bolela hore ditshwantsho tsa ho tobetsa hanngwe le habedi di rometswe). | 1 [byte] | 15 (Litšoantšo tsohle li sebetsa) | 0 – Ha ho na ketsahalo e etsahalang 1 – Konopo e tobetse hang 2 – Senotlolo se tobetse makhetlo a 2 4 – Senotlolo se tobetse makhetlo a 3 8 – Konopo tobetsa mme konopo e lokollwe |
| 41 - Konopo ea bobeli - litšoantšo li rometsoe | ||||
| 150– Tekanyetso | Ho qala ts'ebetso ea othomathiki, khetha boleng ba 3. Ha ts'ebetso ea ho lekanya e atlehile, parameter e nka boleng 1. Ha mokhoa oa ho fetola othomathike o hloleha, parameter e nka boleng 2. Haeba linako tsa phetoho ea sesebelisoa li fetoloa ka letsoho ho sebelisa parameter (156/157), parameter 150 e nka boleng ba 4. | 1 [byte] | 0 (boleng ba kamehla) | 0 – Sesebelisoa ha sea lekanyetsoa 1 - Autocalibration e atlehile 2 - Autocalibration e hlolehile 3 - Ts'ebetso ea calibration 4 - Ho lekanya ka letsoho |
| 151– Ho sebetsa mokgoa | Parameter ena e u nolofalletsa ho fetola ts'ebetso, ho itšetlehile ka sesebelisoa se kopantsoeng. Tabeng ea lifofu tsa venetian, angle ea ho potoloha ha slats le eona e tlameha ho khethoa. | 1 [byte] | 0 (boleng ba kamehla) | 0 - Roller blind, Awning, Pergola, Curtain 1 - Sefofu sa Venetian 90 ° 2 - Sefofu sa Venetian 180 ° |
| 152 – Venetian foufetseng - slats nako e tletseng ea ho fetoha | Bakeng sa lifofu tsa Venetian parameter e lekanya nako ea potoloho e felletseng ea li-slats. Paramethara ha e amane le mekhoa e meng. | 2 [byte] | 15(1.5 metsotsoana) | 0 - 65535 (0 - 6553.5s, tse ling le tse ling tse 0.1) - nako ea ho fetoha |
| 154 - Ho lieha ho lemoha matla ka mor'a hore motlakase o qale |
Paramethara e lokela ho fetoloa feela ha ho sebelisoa likharetene tsa motlakase kapa li-motors tse nang le matla a tlase! Paramethara ena e lokela ho sebelisoa ha enjene e eketsa butle-butle tšebeliso ea matla ha e qala. | 2 [byte] | 10(motsotsoana o le mong) | 0 - 255 (0 - 25.5 metsotsoana) |
| Letlapa la A12 - Roll-Control2 - Litekanyetso tse tsoetseng pele | ||||
| Paramethara | Tlhaloso | Boholo | Boleng ba kamehla | Litekanyetso tse fumanehang |
| 155 - Ho lemoha ts'ebetso ea likoloi | Paramethara e lokela ho fetoloa feela ha ho sebelisoa likharetene tsa motlakase kapa li-motors tse nang le matla a tlase! Moeli oa matla o hlalosoa e le ho fihla moeling oa phetoho. | 2 [byte] | 2 (2 W) | 0 - ho fihlella switch ea moeli ha e fumanehe. Tabeng ena paramethara 150 Calibration e behiloe ho 4 - Palo ea matsoho. U hloka ho lokisa nako ka letsoho ho liparamente 156 le 157.1 - 255 (1 - 255 W) - ho lemoha ha switjha ho qetela. |
| 156 - Nako ea ho nyoloha | Paramethara ena e etsa qeto ea nako e hlokahalang ho fihla ho buloa ka botlalo. Boleng bo behiloe ka boiketsetso nakong ea ts'ebetso ea ho lekanya. E lokela ho behoa ka letsoho haeba ho na le mathata ka autocalibration. | 2 [byte] | 600(60 metsotsoana) | 0 - 65535 (0 - 6553.5 s, mong le e mong 0.1 s) - nako ea ho fetola |
| 157 - Nako ea ho theoha fatše | Paramethara ena e etsa qeto ea nako e hlokahalang ho fihla ho koaloa ka botlalo. Boleng bo behiloe ka tsela e iketsang nakong ea mokhoa oa ho lekanya. E lokela ho behoa ka letsoho haeba ho na le mathata ka autocalibration. |
|||
| 158 - Phetoho ea moeli oa Virtual. Pitsa tshireletso |
Paramethara ena e u nolofalletsa ho beha boemo bo fokolang bo tsitsitseng ba ho theola shutter. Bakeng sa mohlalaample, ho sireletsa pitsa ea lipalesa e lutseng fensetereng. | 1 [byte] | 0 (boleng ba kamehla) | 0-99 |
| 159 - Sebaka seo u se ratang - boemo ba ho bula | Paramethara ena e u thusa ho hlalosa boemo boo u bo ratang ka ho fetesisa. | 1 [byte] | 50 (boleng ba kamehla) | 0-990x FF - Tshebetso e holofetse |
| 160 - Sebaka seo u se ratang - sekhutlo sa slat | Paramethara ena e u thusa ho hlalosa boemo boo u bo ratang ba angle ea slat.
Parameter e sebelisoa feela bakeng sa lifofu tsa venetian. |
|||
LIEKETSO Z-WAVE
Indicator CC - lits'oants'o tse fumanehang
ID ea sesupo - 0x50 (tsebahatsa)
Indicator CC - thepa e fumanehang
| Letlapa la A13 - Roll-Control2 - Indicator CC | ||
| ID ea thepa | Tlhaloso | Litekanyetso le litlhoko |
| 0x03 | Linako tsa Toggling, On/Off | E qala ho fetoha pakeng tsa HO UTLOA le HO TLOA E sebedisoa ho seta nako ya Nako ya Ho Tswa/Ho Tswa.Maemo a teng:
Haeba sena se boletsoe, Mekoloko ea On / Off E TSOA le eona e tla boleloa. |
| 0x04 | Toggling, On/Off Cycles | E sebedisetswa ho seta palo ya dinako tsa On/Off.Maemo a teng:
Haeba sena se boletsoe, nako ea ho bula / ho tima le eona e tlameha ho boleloa. |
| 0x05 | Toggling, Ka nako nakong ea On/Off | E sebedisetswa ho seta bolelele ba Nako ka nako ya On/Off. E lumella linako tse tšoanang tsa On/Off. Maemo a fumanehang
Example: 300ms ON le 500ms OFF e finyelloa ka ho beha nako ea On/Off (0x03) = 0x08 le Ka nako ka hare ho Nako ea On/Off (0x05) = 0x03 Boleng bona bo hlokomolohuoa haeba linako tsa On/Off li sa hlalosoa. Boleng bona bo hlokomolohuoa haeba boleng ba linako tsa On/Off bo le ka tlase ho boleng bona. |
Lithuto tsa Taelo tse tšehelitsoeng
| Letlapa la A14 - Roll-Control2 - Lihlopha tsa Taelo tse Tšehetsoeng | ||
| Sehlopha sa Taelo | Phetolelo | Sireletsehile |
| COMMAND_CLASS_APPLICATION_STATUS [0x22] | V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO [0x5E] | V2 | |
| COMMAND_CLASS_WINDOW_COVERING [0x6A] | V1 | EE |
| COMMAND_CLASS_SWITCH_MULTILEVEL [0x26] | V4 | EE |
| COMMAND_CLASS_ASSOCIATION [0x85] | V2 | EE |
| COMMAND_CLASS_MULTI_CHANNEL ASSOCIATION [0x8E] | V3 | EE |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO [0x59] | V3 | EE |
| COMMAND_CLASS_TRANSPORT_SERVICE [0x55] | V2 | |
| COMMAND_CLASS_VERSION [0x86] | V3 | EE |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC [0x72] | V2 | EE |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY [0x5A] | V1 | EE |
| COMMAND_CLASS_POWERLEVEL [0x73] | V1 | EE |
| COMMAND_CLASS_SECURITY [0x98] | V1 | |
| COMMAND_CLASS_SECURITY_2 [0x9F] | V1 | |
| COMMAND_CLASS_METER [0x32] | V3 | EE |
| COMMAND_CLASS_CONFIGURATION [0x70] | V4 | EE |
| COMMAND_CLASS_NOTIFICATION [0x71] | V8 | EE |
| COMMAND_CLASS_PROTECTION [0x75] | V2 | EE |
| COMMAND_CLASS_CENTRAL_SCENE [0x5B] | V3 | EE |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD [0x7A] | V5 | EE |
| COMMAND_CLASS_SUPERVISION [0x6C] | V1 | |
| COMMAND_CLASS_INDICATOR [0x87] | V3 | EE |
| COMMAND_CLASS_BASIC [0x20] | V2 | EE |
Motheo oa CC
| Letlapa la A15 - Roll-Control2 - Basic CC | |||
| Taelo | Boleng | Taelo ea 'mapa | Boleng ba 'mapa |
| Basic Set | [0xFF] | Multilevel Switch Set | [0xFF] |
| Basic Set | [0x00] | Multilevel Switch Set | Multilevel Switch Set |
| Basic Set | [0x00] ho ea ho [0x63] | Phetoho ea Maemo a ho Qala (Holimo / Tlase) | [0x00], [0x63] |
| Fumana Basic | Multilevel Switch Fumana | ||
| Tlaleho ea Motheo (Boleng ba Hona Joale le Boleng ba Sepheo TŠOANTŠE ho hlophisoa ho 0xFE haeba u sa hlokomele boemo.) | Tlaleho ea switch ea Multilevel | ||
Tsebiso CC
Sesebelisoa se sebelisa Notification Command Class ho tlaleha liketsahalo tse fapaneng ho molaoli ("Lifeline" Group).
| Letlapa la A16 - Roll-Control2 - Notification CC | ||||
| Mofuta oa Tsebiso | Ketsahalo / Naha | Paramethara | Boemo | Qetellong |
| Taolo ea Matla [0x08] | E sa sebetse [0x00] | – | 0xFF - thusa (ha e fetohe) | Motso |
| Hajoale e fumanoe [0x06] | ||||
| Sistimi [0x09] | E sa sebetse [0x00] | |||
| Ho hloleha ha lisebelisoa tsa sistimi e nang le khoutu e hlolehileng ea moetsi [0x03] | MP khoutu: 0x01 [sesebediswa overheat] | 0xFF - thusa (ha e fetohe) | Motso | |
Ts'ireletso CC
Sehlopha sa Taelo ea Ts'ireletso se lumella ho thibela taolo ea lehae kapa e hole ea liphetho.
| Letlapa la A17 - Roll-Control2 - Tšireletso CC | |||
| Mofuta | Naha | Tlhaloso | Tlhahiso |
| Sebakeng | 0 | Ha e itšireletse - Sesebelisoa ha sea sireletsoa, 'me se ka sebetsoa ka tloaelo ka sehokelo sa mosebelisi. | Likonopo tse amanang le liphetho. |
| Sebakeng | 2 | Ha ho ts'ebetso e ka khonehang - konopo e ke ke ea fetola boemo ba relay, ts'ebetso efe kapa efe e teng (menu). | Likonopo tse khaotsoeng ho tsoa ho liphetho. |
| RF | 0 | E sa sireletsoeng - Sesebelisoa se amohela le ho arabela Litaelo tsohle tsa RF. | Lihlahisoa li ka laoloa ka Z-Wave. |
| RF | 1 | Ha ho taolo ea RF - taelo ea mantlha ea sehlopha sa taelo le switch binary e hanngoe, sehlopha se seng le se seng sa taelo se tla sebetsoa. | Lintho tse hlahisoang li ke ke tsa laoloa ka Z-Wave. |
Metara CC
| Letlapa la A18 - Roll-Control2 - Meter CC | ||||
| Mofuta oa Meter | Sekala | Mofuta oa sekhahla | Nepahalo | Boholo |
| Motlakase [0x01] | Motlakase_kWh [0x00] | Kenya [0x01] | 1 | 4 |
Ho fetola bokhoni
NICE Roll-Control2 e sebelisa li-ID tse fapaneng tsa Window Covering Parameter ho latela boleng ba liparamente tse 2:
- Boemo ba ho lekanya (parameter 150),
- Mokhoa oa ho sebetsa (parameter 151).
| Tafole ea A19 - Roll-Control2 - Ho fetola bokhoni | ||
| Boemo ba ho lekanya (paramethara 150) | Mokhoa oa ho sebetsa (parameter 151) | Li-ID tsa Paramethara tsa Lifensetere tse tšehelitsoeng |
| 0 - Sesebelisoa ha sea lekanngoa kapa 2 - Autocalibration e hlolehile |
0 - Roller blind, Awning, Pergola, Curtain | ka ntle_tlase (0x0C) |
| 0 - Sesebelisoa ha sea lekanngoa kapa 2 - Autocalibration e hlolehile |
1 - Sefofu sa Venetian 90 ° kapa 2 - Roller blind e nang le mokhanni ea hahelletsoeng ka hare ho 180 ° |
ka ntle_tlase (0x0C) Lehlakore le tšekaletseng la li-slats (0x16) |
| 1 - Autocalibration e atlehile kapa 4 - Ho lekanya ka letsoho |
0 - Roller blind, Awning, Pergola, Curtain | ka ntle_tlase (0x0D) |
| 1 - Autocalibration e atlehile kapa 4 - Ho lekanya ka letsoho |
1 - Sefofu sa Venetian 90 ° kapa 2 - Roller blind e nang le mokhanni ea hahelletsoeng ka hare ho 180 ° |
ka ntle_tlase (0x0D) angle e tšekaletseng ea li-slats (0x17) |
Haeba e 'ngoe ea li-parameter 150 kapa 151 e fetoha, molaoli o lokela ho etsa ts'ebetso ea ho sibolla hape ho nchafatsa sete ea Li-ID tsa Liparametha tse Tšehetsoeng tsa Window Covering.
Haeba molaoli a sa khone ho etsa ts'ebetso ea ho sibolla hape, hoa hlokahala ho kenyelletsa node marang-rang hape.
Tlhahisoleseling ea Sehlopha sa Mokhatlo CC
| Lethathamo la A20 - Roll-Control2 - Boitsebiso ba Sehlopha sa Mokhatlo CC | |||
| Sehlopha | Profile | Sehlopha sa Taelo le Taelo | Lebitso la Sehlopha |
| 1 | Kakaretso: Lifeline (0x00: 0x01) | DEVICE_RESET_LOCALLY_NOTIFICATION [0x5A 0x01] | Lifeline |
| NOTIFICATION_REPORT [0x71 0x05] | |||
| SWITCH_MULTILEVEL_REPORT [0x26 0x03] | |||
| WINDOW_COVERING_REPORT [0x6A 0x04] | |||
| CONFIGURATION_REPORT [0x70 0x06] | |||
| INDICATOR_REPORT [0x87 0x03] | |||
| METER_REPORT [0x32 0x02] | |||
| CENTRAL_SCENE_CONFIGURATION_ REPORT [0x5B 0x06] | |||
| 2 | Taolo: KEY01 (0x20: 0x01) | WINDOW_COVERING_SET [0x6A 0x05] | Ho koahela fensetere |
| WINDOW_COVERING_START_LVL_ CHANGE [0x6A 0x06] | |||
| WINDOW_COVERING_STOP_LVL_ CHANGE [0x6A 0x07] | |||
MOLAOLI
Litsebiso tsa Molao:
Lintlha tsohle, ho kenyeletsoa, empa ha li felle feela, tlhahisoleseling mabapi le likarolo, ts'ebetso, le/kapa litlhaloso tse ling tsa sehlahisoa li ka fetoha ntle le tsebiso. NICE e na le litokelo tsohle tsa ho ntlafatsa kapa ho ntlafatsa lihlahisoa tsa eona, software, kapa litokomane ntle le tlamo ea ho tsebisa motho kapa mokhatlo ofe kapa ofe. NICE logo ke lets'oao la khoebo la NICE SpA Oderzo TV Italia Mabitso a mang kaofela le mabitso a lihlahisoa a boletsoeng mona ke matšoao a beng ba ona ka ho fapana.
Tumellano ea litaelo ea WEEE
Sesebelisoa se ngotsoeng ka letšoao lena ha sea lokela ho lahloa le litšila tse ling tsa ka tlung.
E tla fetisetsoa sebakeng se sebetsang sa pokello bakeng sa ho sebelisoa bocha ha lisebelisoa tsa motlakase le tsa elektroniki.
Phatlalatso ea ho lumellana
Ka hona, NICE SpA Oderzo TV Italia e phatlalatsa hore sesebelisoa se latela litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 2014/53/EU. Temana e felletseng ea phatlalatso ea EU ea tumellano e fumaneha atereseng e latelang ea inthanete: www.niceforyou.com/en/download?v=18
E ntle SpA
Oderzo TV Italia
info@niceforyou.com
www.mellatooui.com
Litokomane / Lisebelisoa
 |
Nice Roll-Control2 Z Wave Blind and Awning Controller [pdf] Buka ea Taelo Roll-Control2 Z Wave Blind and Awning Controller, Roll-Control2, Z Wave Blind and Awning Controller, Sefofu le Mookameli oa Moaho, Mookameli oa Awning, Mookameli. |
