MT40 Linear Image Barcode Scan Enjene, Tataiso ea Kopanyo, V2.3
MT40 (3.3-5V Long Range Barcode Scan Engine)
MT4OW (3.3-5V Wide Angle Barcode Scan Engine)
Tataiso ea ho Kopanya
LIEKETSENG
MT40 Linear Image Barcode Scan Engine e etselitsoe 1D e phahameng ea ts'ebetso ea barcode scanning e nang le ts'ebetso e nepahetseng le ho kopanya habonolo. MT40 e loketse ho kopanngoa ho li-terminals tsa data le lisebelisoa tse ling tse nyenyane tsa mohala. Mofuta oa Wide-angle (MT40W) le ona oa fumaneha.
MT40 e na le li-LED tse 2 tse khanyang, sensor ea boleng bo holimo ea linear le microprocessor e nang le firmware e matla ho laola likarolo tsohle tsa ts'ebetso le ho nolofalletsa puisano le sistimi ea moamoheli holim'a sete e tloaelehileng ea likhokahano tsa puisano.
Li-interfaces tse peli, UART & USB, lia fumaneha. UART segokanyimmediamentsi sa sebolokigolo buisana le tsamaiso ea moamoheli holim'a TTL-level RS232 puisano; Sehokelo sa USB se etsisa sesebediswa sa Keyboard sa USB mme se buisana le moamoheli ka USB.
1-1. Setšoantšo sa MT 40 Block
1-2 .. Motlakase Interface
1-2-1. Kabelo ea Pin
| Pin # | UART | USB | I/O | Tlhaloso | Sekema Example |
| 1 | VCC | VCC | ———— | Phepelo voltage kenya. E tlameha ho hokela motlakase oa 3.3 kapa 5V kamehla. |  |
| 2 | RXD | ———— | Kenyeletso | Tlhahiso ea data ea UART TTL. |  |
| 3 | Hlahisa | Hlahisa | Kenyeletso | Holimo: Power-up/Standby Low: Ts'ebetso ea ho hlahloba *Tlhokomeliso: 1. Ho theoha ha matla-up ho tla etsa hore enjene e hlahlobe hore e kene ka mokhoa oa ntlafatso ea firmware. |
 Hang ha "trigger" e totoba (hula tlase), ts'ebetso ea ho skena e tsoela pele ho fihlela barcode e hlakisoa ka katleho kapa trigger e lokolloa (hulela holimo). Ho tsoelapele ts'ebetsong e latelang ea ho skena, lokolla (hulela holimo) pele ebe o tobetsa (hulela tlase) sebatli hape. |
| Pin # | UART | USB | I/O | Tlhaloso | Sekema Example |
| 4 | Matla a nolofalletsa | Matla a nolofalletsa | Kenyeletso | Holimo: Enjene ea Scan e Tloha Tlase: Enjene ea Scan e Buletsoe *Ntle le: 1. Nakong ea data phetiso 2. Ho ngolla mekhahlelo ho mohopolo o sa fetoheng. |
Ha phini ea Power Enable e le holimo, enjene ea scan e tla koaloa ka tšebeliso ea matla e ka tlase ho 1uA. |
| 5 | TXD | ———— | Sephetho | Tlhahiso ea data ea UART TTL. |  |
| 6 | RTS | ———— | Sephetho | Ha ho ts'oarana ka matsoho ho lumelletsoe, MT40 e kopa tumello ho tsoa ho moamoheli ho fetisetsa data moleng oa TXD. |  |
| 7 | GND | GND | ———— | Matla le pontšo fatše. |  |
| 8 | ———— | USB D + | Ho iketsetsa liqeto | Phetiso ea Letšoao la Phapang |  |
| Pin # | UART | USB | I/O | Tlhaloso | Sekema Example |
| 9 | LED | LED | Sephetho | E sebetsa e le hodimo, e bontsha boemo ba Power-Up kapa barcode e atlehileng e entsweng (Good Read). |  |
| 10 | CTS | ———— | Kenyeletso | Ha ho ts'oarana ka matsoho ho lumelletsoe, moamoheli o lumella MT40 ho fetisetsa data moleng oa TXD. |  |
| 11 | Buzzer | Buzzer | Sephetho | hodimo e sebetsang: Power-Up kapa barcode e atlehileng e entsweng. Letšoao le laoloang la PWM le ka sebelisoa ho khanna buzzer ea kantle bakeng sa barcode e atlehileng e entsoeng (Good Read). |
 |
| 12 | ———— | USB D- | Ho iketsetsa liqeto | Phetiso ea Letšoao la Phapang |  |
1-2-2. Litšobotsi tsa Motlakase
| Letšoao | Lintlha | Min | Max | Yuniti |
| VIH | Kenya boemo bo phahameng | VDD x 0.65 | VDD + 0.4 | V |
| VIL | Kenya boemo bo tlase | - 0.4 | VDD x 0.35 | V |
| VOH | Sephetho se phahameng | VDD - 0.4 | – | V |
| VOL | Sephetho sa boemo bo tlase | – | 0.4 | V |
| VESD | Electrostatic discharge voltage (mokhoa oa 'mele oa motho) | - 4000 | + 4000 | V |
*Hlokomela:
- Phepelo ea Matla: VDD= 3.3 kapa 5 V
- Ho pepesetsoa maemo a phahameng a litekanyetso ka nako e telele ho ka ama ts'epahalo ea sesebelisoa.
1-2-3. Flex Cable
The flex cable e sebelisoa ho hokahanya MT40 le lehlakore la baeti. Ho na le lithakhisa tse 12 ka lehlakoreng la enjene (MT40) le lehlakoreng la moamoheli. Ka kopo bona Khaolo ea 2-10 bakeng sa lintlha tse ling tsa flex cable.
| Thapo ea Flex (P/N: 67XX-1009X12) |
|
| Pin # | Tobetsa Kabelo Ho Moamohela |
| 1 | VCC |
| 2 | RXD |
| 3 | Hlahisa |
| 4 | Matla a nolofalletsa |
| 5 | TXD |
| 6 | RTS |
| 7 | GND |
| 8 | USB D + |
| 9 | LED |
| 10 | CTS |
| 11 | Buzzer |
| 12 | USB D- |
*Hlokomela: E lumellana le kabelo ea phini ea MARSON MT742(L)/MT752(L).
1-3. Nako ea Ts'ebetso
Khaolo ena e hlalosa nako e amanang le mekhoa e fapaneng ea ts'ebetso ea MT40 ho kenyelletsa Power Up, Mode ea Boroko, le Decode Timing.
1-3-1. Matlafatsa
Ha matla a qala ho sebelisoa, MT40 ea sebetsa 'me e qala ts'ebetso ea ho qala. Hang ha ho qalisoa (nako =: 10mS) ho phethiloe, MT40 e kena Boemong ba Boemo 'me e se e loketse ho hlahlojoa ke barcode.
1-3-2. Mokhoa oa ho robala
MT40 e ka kena Mokhoa oa ho Robala kamora hore nako e lokiselitsoeng e fete ntle le ts'ebetso efe kapa efe. Ka kopo, sheba Khaolo ea 6 bakeng sa lintlha tse ling mabapi le Mokhoa oa ho Robala.
1-3-3. Hlalosa Nako
Boemong ba Standby, MT40 e kentsoe tšebetsong ke lets'oao la Trigger le LOKELA ho bolokoa tlase bonyane 20 ms ho fihlela scan e atlehileng e fihletsoe, joalo ka ha ho bonts'itsoe ke matšoao a Buzzer/LED.
Mokhoeng oa ho Robala, MT40 e ka tsosoa ke lets'oao la Trigger le LOKELA ho bolokoa le le tlase bonyane 2 mS, e tla etsa hore enjene ea scan e kene Boemong ba Standby.
Kakaretso ea nako ea ho hlahloba le ho khetholla e batla e lekana le nako ea ho tloha lets'oao la Trigger le eang tlase ho letšoao la Buzzer / LED le ea holimo. Nako ena e tla fapana hanyane ho ipapisitsoe le lintlha tse 'maloa tse kenyelletsang boleng ba barcode, mofuta oa barcode le sebaka se pakeng tsa MT40 le barcode e sekiloeng.
Ha ho hlahlojoa ka katleho, MT40 e hlahisa lets'oao la Buzzer / LED mme e boloka lets'oao lena nako eohle ea phetisetso ea data e kentsoeng lehlakoreng la moamoheli. Nako e ka bang 75 ms.
Ka hona, nako eohle ea ts'ebetso e tloaelehileng ea ho hlahloba (ho tloha ho Trigger ho ea tlaase ho ea qetellong ea letšoao la Buzzer PWM) le eona e ka ba 120mS.
1-3-4. Kakaretso ea Nako ea Ts'ebetso
- Nako e phahameng ea ho qala ke 10mS.
- Nako e telele ea ts'ebetso ea ho hlahloba Boemong ba Standby ke 120mS.
- Nako e fokolang ea ho tsosa MT40 ho Mode ea Boroko ka lets'oao la Trigger e ka ba 2 ms.
- Nako e telele ea ho tsosa MT40 ho tsoa ho Mokhoa oa Boroko ka lets'oao la Trigger le ho phethela decode (ha barcode e le ka har'a sepheo se nepahetseng) e ka ba 120ms.
LIEKETSENG TS'OANELO
2-1. Selelekela
Khaolo ena e fana ka litlhaloso tsa tekheniki tsa enjene ea scan ea MT40.
Mokhoa oa ts'ebetso, sebaka sa ho skena le angle ea ho hlahloba le tsona li hlahisoa.
2-2. Litlhaloso tsa Tekheniki
| Optic & Tshebetso | |||
| Mohloli oa Leseli | LED e khubelu ea 625nm e bonahalang | ||
| Sensoro | Sensor ea Linear Image | ||
| Scan Rate | 510 Scans/ ka motsotsoana (Smart Detection) | ||
| Qeto | MT40: 4mil/0.1mm; MT40W: 3mil/0.075mm | ||
| Skena Angle | MT40: 40°; MT40W: 65° | ||
| Print Contrast Ratio | 30% | ||
| Bophara ba Tšimo (13Mil Khouto39) | MT40: 200 limilimithara; MT40W: 110 limilimithara | ||
| E tloaelehileng Botebo Ba Tšimo (Tikoloho: 800 lux) | Khoutu \ Mohlala | MT40 | MT40W |
| 3 mil Khoutu39 | N/A | 28 ~ 70mm (litlhaloso tse 13) | |
| 4 mil Khoutu39 | 51 ~ 133mm (litlhaloso tse 4) | 19 ~ 89mm (litlhaloso tse 4) | |
| 5 mil Khoutu39 | 41 ~ 172mm (litlhaloso tse 4) | 15 ~ 110mm (litlhaloso tse 4) | |
| 10 mil Khoutu39 | 27 ~ 361mm (litlhaloso tse 4) | 13 ~ 213mm (litlhaloso tse 4) | |
| 15 mil Khoutu39 | 42 ~ 518mm (litlhaloso tse 4) | 22 ~ 295mm (litlhaloso tse 4) | |
| 13 mil UPC/ EAN | 37 ~ 388mm (litlhaloso tse 13) | 21 ~ 231mm (litlhaloso tse 13) | |
| Guaranteed Botebo ba Tšimo (Tikoloho: 800 lux) | 3 mil Khoutu39 | N/A | 40 ~ 65mm (litlhaloso tse 13) |
| 4 mil Khoutu39 | 65 ~ 120mm (litlhaloso tse 4) | 30 ~ 75mm (litlhaloso tse 4) | |
| 5 mil Khoutu39 | 60 ~ 160mm (litlhaloso tse 4) | 30 ~ 95mm (litlhaloso tse 4) | |
| 10 mil Khoutu39 | 40 ~ 335mm (litlhaloso tse 4) | 25 ~ 155mm (litlhaloso tse 4) | |
| 15 mil Khoutu39 | 55 ~ 495mm (litlhaloso tse 4) | 35 ~ 195mm (litlhaloso tse 4) | |
| 13 mil UPC/ EAN | 50 ~ 375mm (litlhaloso tse 13) | 35 ~ 165mm (litlhaloso tse 13) | |
| Litšobotsi Tsa 'Mele | |||
| Boemo | (W)32 x (L)24 x (H)11.6 limilimithara | ||
| Boima ba 'mele | 8g | ||
| Mmala | Ntsho | ||
| Lintho tse bonahalang | ABS | ||
| Sehokedi | 12pin (sekontiri = 0.5mm) ZIF | ||
| Cable | 12pin (sekontiri = 0.5mm) thapo ea flex |
| Motlakase | |
| Tshebetso Voltage | 3.3 ~ 5VDC ± 5% |
| Mosebetsi oa Hona Joale | <160 mA |
| Standby Current | <80 mA |
| Qetello/ Boroko ba Hona Jwale | <8 mA (bona Khaolo ea 6 bakeng sa Mokhoa oa ho Robala) |
| Matla a tlase hona joale | <1A (bona Khaolo ea 1-2-1 bakeng sa phini ea Power Enable) |
| Surge Current | <500 mA |
| Khokahano | |
| Sehokedi | UART (TTL-level RS232) |
| USB (HID Keyboard) | |
| Tikoloho ea Mosebelisi | |
| Mocheso oa ho sebetsa | -20°C ~ 60°C |
| Mocheso oa polokelo | -25°C ~ 60°C |
| Mongobo | 0% ~ 95%RH (Ha e fokotsehe) |
| Drop Durability | 1.5M |
| Ambient Light | 100,000 Lux (Leseli la Letsatsi) |
| Matšoao | UPC-A/ UPC-E EAN-8/ EAN-13 Matrix 2 ho tse 5 Khoutu ea Poso ea Chaena (Khoutu ea Toshiba) Indasteri ea 2 ho tse 5 E kenelletse 2 ho tse 5 Standard 2 of 5 (IATA Code) Codabar Khoutu 11 Khoutu 32 Khoutu e Tloaelehileng 39 Khoutu e felletseng ea ASCII 39 Khoutu ea 93 Khoutu 128 EAN/ UCC 128 (GS1-128) MSI/ UK Plessey Code Telepen Code Tlhatlhobo ea GS1 |
| Taolo | |
| ESD | E sebetsa ka mor'a ho kopana le 4KV, ho tsoa moeeng oa 8KV (e hloka bolulo bo etselitsoeng tšireletso ea ESD le ho kheloha masimong a motlakase.) |
| EMC | FCC - Karolo ea 15 Karolo ea B (Sehlopha sa B) CE - EN55022, EN55024 |
| Kamohelo ea polokeho | IEC 62471 (Sehlopha sa Ts'ebetso) |
| Tikoloho | WEEE, RoHS 2.0 |
2-3. Sehokedi
2-3-1. UART Interface
Sekhahla sa Baud: 9600
Lintlha tsa data: 8
Parity: Ha ho letho
Emisa Bit: 1
Ho tšoara matsoho: Ha ho letho
Nako ea ho Laola Phallo: Ha ho letho
ACK/NAK: TLOA
BCC: TLOA
Litšobotsi:
- E ka hlophisoa ka ho lekola libarcode tsa tlhophiso kapa Ez Utility' (sesebelisoa sa software se thehiloeng ho PC, se fumanehang bakeng sa ho jarolleloa ho www.marson.com.tw)
- E tšehetsa lisebelisoa tsa hardware le lisebelisoa tsa software
- E ts'ehetsa puisano ea mahlakore a mabeli (taelo ea serial)
Khoutu ea Configuration ea Sebopeho:
Ho hlahloba ka holimo barcode ho tla beha MT40 ea hau ho UART interface.
2-3-2. Sesebelisoa sa USB
Litšobotsi:
- E ka hlophisoa ka ho lekola libarcode tsa tlhophiso kapa Ez Utility® (sesebelisoa sa software se thehiloeng ho PC, se fumanehang bakeng sa ho jarolleloa ho www.marson.com.tw)
- E tšehetsa hardware trigger feela
- E etsisa sesebelisoa sa Keyboard sa USB
Khoutu ea Configuration ea Sebopeho:
Ho skena ka holimo barcode ho tla seta MT40 ea hau ho sebopeho sa USB HID.
2.4 Mokhoa oa Ts'ebetso
- Ka matla-up, MT40 e romela lipontšo tsa Power-Up holim'a Buzzer le LED pins e le pontšo ea hore MT40 e kena Moeteng oa Boemo 'me e se e loketse ho sebetsa.
- Hang ha MT40 e qalisoa ke mokhoa oa hardware kapa software, e tla hlahisa letlapa le moqotetsane, le otlolohileng la leseli le tsamaellanang le sebaka sa sensor. view.
- Sensor ea linear ea setšoantšo e nka setšoantšo se otlolohileng sa barcode mme e hlahisa analog waveform, e leng sampe etelletsoeng pele le ho hlahlobisisoa ke "decoder firmware" e sebetsang ho MT40.
- Ka mor'a barcode e atlehileng, MT40 e tima mabone a LED, e romela melaetsa ea Good Read ka Buzzer le li-pins tsa LED ebe e fetisetsa boitsebiso bo khantšitsoeng ho moamoheli.
- MT40 e ka kena Mokhoa oa ho Robala (Ka kopo, sheba Khaolo ea 6 bakeng sa lintlha tse ling) ka mor'a nako ea ho se sebetse e le ho fokotsa tšebeliso ea matla.
2.5 Boemo ba Mechini
(Yuniti = mm)
2-6. Sebaka sa ho hlahloba
2-6-1. Mofuta o Tloaelehileng oa ho Scanning
Boemo ba Teko - MT40
Bolelele ba Barcode: Litlhaku tsa Code39 - 4
EAN/UPC - litlhaku tse 13
Karolelano ea Bar & Space: 1 ho 2.5
Papiso ea Phapang ea Khatiso: 0.9
Leseli la Ambient:> 800 lux
Bohole bo Tlwaelehileng ba Bonyane le Bogologolo ba Scan ya MT40
| Symbology | Qeto | Sebaka | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 4 Mil | 43 ~ 133 limilimithara | 4 makhabane. |
| 5 Mil | 41 ~ 172 limilimithara | ||
| 10 Mil | 27 ~ 361 limilimithara | ||
| 15 Mil | 42 ~ 518 limilimithara | ||
| EAN 13 | 13 Mil | 37 ~ 388 limilimithara | 13 makhabane. |
Tloaelehileng Maximum Scan Width ea MT40
| Symbology | Qeto | Bolelele ba Barcode | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 13 Mil | 200 limilimithara | 37 makhabane. |
Boemo ba Teko - MT40W
Bolelele ba Barcode: Code39 3mil - litlhaku tse 13, Code39 4/5/10/15mil - litlhaku tse 4
EAN/UPC - litlhaku tse 13
Karolelano ea Bar & Space: 1 ho 2.5
Papiso ea Phapang ea Khatiso: 0.9
Leseli la Ambient:> 800 lux
Bohole bo Tloaelehileng ba Bonyane le Bo phahameng ka ho Fetisisa ba MT40W
| Symbology | Qeto | Sebaka | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 3 Mil | 28 ~ 70 limilimithara | 13 makhabane. |
| 4 Mil | 19 ~ 89 limilimithara | 4 makhabane. | |
| 5 Mil | 15 ~ 110 limilimithara | ||
| 10 Mil | 13 ~ 213 limilimithara | ||
| 15 Mil | 22 ~ 295 limilimithara | ||
| EAN 13 | 13 Mil | 21 ~ 231 limilimithara | 13 makhabane. |
Tloaelehileng Maximum Scan Width ea MT40W
| Symbology | Qeto | Bolelele ba Barcode | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 13 Mil | 110 limilimithara | 19 makhabane. |
2-6-2. Guaranteed Scanning Range
Boemo ba Teko - MT40
Bolelele ba Barcode: Litlhaku tsa Code39 - 4
EAN/UPC - litlhaku tse 13
Karolelano ea Bar & Space: 1 ho 2.5
Papiso ea Phapang ea Khatiso: 0.9
Leseli la Ambient:> 800 lux
E netefalitsoeng ea Bonyane & Bolelele ba Bohole ba Scan ea MT40
| Symbology | Qeto | Sebaka | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 4 Mil | 65 ~ 120 limilimithara | 4 makhabane. |
| 5 Mil | 60 ~ 160 limilimithara | ||
| 10 Mil | 40 ~ 335 limilimithara | ||
| 15 Mil | 55 ~ 495 limilimithara | ||
| EAN 13 | 13 Mil | 50 ~ 375 limilimithara | 13 makhabane. |
Guaranteed Maximum Scan Width ea MT40
| Symbology | Qeto | Bolelele ba Barcode | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 13 Mil | 200 limilimithara | 37 makhabane. |
Boemo ba Teko - MT40W
Bolelele ba Barcode: Code39 3mil - litlhaku tse 13, Code39 4/5/10/15mil - litlhaku tse 4
EAN/UPC - litlhaku tse 13
Karolelano ea Bar & Space: 1 ho 2.5
Papiso ea Phapang ea Khatiso: 0.9
Leseli la Ambient:> 800 lux
E netefalitsoeng ea Bonyane le Bohole Bohole ba Scan MT40W
| Symbology | Qeto | Sebaka | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 3 Mil | 40 ~ 65 limilimithara | 13 makhabane. |
| 4 Mil | 30 ~ 75 limilimithara | 4 makhabane. | |
| 5 Mil | 30 ~ 95 limilimithara | ||
| 10 Mil | 25 ~ 155 limilimithara | ||
| 15 Mil | 35 ~ 195 limilimithara | ||
| EAN 13 | 13 Mil | 35 ~ 165 limilimithara | 13 makhabane. |
Boholo bo netefalitsoeng ba Scan Width ea MT40W
| Symbology | Qeto | Bolelele ba Barcode | Nomoro ea Litlhaku tse Khoutulitsoeng |
| Khoutu e Tloaelehileng 39 (w/o checksum) | 13 Mil | 110 limilimithara | 19 makhabane. |
2-7. Pitch Angle, Roll Angle le Skew Lenaka
Ela hloko ho mamella ha molumo oa lentsoe, roll le skew angle ea bar code eo u lekang ho e hlahloba.
2-8. Specular Dead Sebaka
Se ke oa beha MT40 ka kotloloho holim'a barcode. Leseli le khutlelang ka ho toba ho MT40 ho tloha ho barcode le tsejoa e le specular reflection, e ka etsang hore ho be thata ho khetholla. Sebaka se ikhethileng se shoeleng sa MT40 se fihla ho 5 ° ho latela sebaka se shebiloeng le ho benya ha karoloana.
2-9. Curvature Degree
| Barcode | EAN13 (L=37mm) | |
| Qeto | 13 mil (0.33 limilimithara) | 15.6 mil (0.39 limilimithara) |
| R | R ≧ 20 limilimithara | R ≧ 25 limilimithara |
| d (MT40) | 90 limilimithara | 120 limilimithara |
| d (MT40W) | 40 limilimithara | 50 limilimithara |
| PCS | 0.9 (e hatisitsoeng pampiring ea lifoto) | |
2-10. Flex Cable Tlhaloso
Tekanyo ea curvature ea barcode e hlahlobiloeng e hlalositsoe ka tlase:
2-11. Tlhaloso ea Screw
Ka tlase ke setšoantšo sa li-screws tsa M1.6×4(P/N: 4210-1604X01) tse tlang le MT40.
2-12. Tlhaloso ea Mohokahanyi
Ka tlase ke setšoantšo sa 12-pin 0.5-pitch FPC Connector(P/N: 4109-0050X00) ea MT40.
KEKETSO
Enjene ea scan ea MT40 e etselitsoe ka kotloloho ho kopanngoa ntlong ea bareki bakeng sa lits'ebetso tsa OEM. Leha ho le joalo, ts'ebetso ea MT40 e tla ameha hampe kapa e senyehe ruri ha e kentsoe ka har'a sebaka se sa lokelang.
Tlhokomeliso: Tiisetso e lekanyelitsoeng ha e na thuso haeba likhothaletso tse latelang li sa lateloe ha u kenya MT40.
3-1. Tlhokomeliso ea ho tsoa ha Electrostatic
Li-MT40 tsohle li romelloa ka har'a liphutheloana tsa ts'ireletso tsa ESD ka lebaka la sebopeho se hlokolosi sa likarolo tsa motlakase tse pepesitsoeng.
- Kamehla sebelisa likhoele tsa letsoho tse theohileng fatše le sebaka sa mosebetsi se theiloeng fatše ha u bula le ho tšoara MT40.
- Hloekisa MT40 ntlong e etselitsoeng tšireletso ea ESD le masimo a motlakase a khelohileng.
3-2. Mechanical Dimension
Ha u sireletsa MT40 ka ho sebelisa li-screw tsa mochini:
- Tlohela sebaka se lekaneng ho amohela boholo ba boholo ba MT40.
- Se ke oa feta 1kg-cm (0.86 lb-in) ea torque ha u sireletsa MT40 ho moamoheli.
- Sebelisa mekhoa e sireletsehileng ea ESD ha u tšoara le ho kenya MT40.
3-3. Lisebelisoa tsa Lifensetere
Lintlha tse latelang ke litlhaloso tsa lisebelisoa tse tharo tse tsebahalang tsa fensetere:
- Poly-methyl Methacrylic (PMMA)
- Allyl Glycol Carbonate (ADC)
- Khalase e phaphametseng ka lik'hemik'hale
Cell Cast Acrylic (ASTM: PMMA)
Cell cast Acrylic, kapa Poly-methyl Methacrylic e entsoe ka ho lahla acrylic pakeng tsa likhalase tse peli tse nepahetseng. Thepa ena e na le boleng bo botle haholo ba optical, empa e batla e le bonolo ebile e ka hlaseloa habonolo ke lik'hemik'hale, khatello ea mochini le khanya ea UV. Ho khothaletsoa ka matla ho ba le acrylic e koahetsoeng ka thata le Polysiloxane ho fana ka khanyetso ea abrasion le ts'ireletso ho tsoa linthong tsa tikoloho. Acrylic e ka khaoloa ka laser ka libopeho tse sa tloaelehang 'me e entsoe ka ultrasonically welded.
Cell Cast ADC, Allyl Diglycol Carbonate (ASTM: ADC)
E boetse e tsejoa e le CR-39™, ADC, polasetiki e futhumatsang e sebelisoang haholo bakeng sa likhalase tsa mahlo tsa polasetiki, e na le khanyetso e ntle ea lik'hemik'hale le tikoloho. E boetse e na le boima bo leka-lekaneng ka tlhaho, ka hona ha e hloke ho roala ka thata. Boitsebiso bona bo ke ke ba etsoa ka ultrasonically welded.
Khalase e Phaphallang ka Lik'hemik'hale
Khalase ke thepa e thata e fanang ka ts'ebetso e ntle haholo ea ho hopa le ho haneloa. Leha ho le joalo, khalase e sa kenngoang e brittle. Ho eketsa matla a ho feto-fetoha le maemo a fokolang a optical ho hloka mocheso oa lik'hemik'hale. Khalase ha e khone ho chesetsoa ka ultrasonically 'me ho thata ho e khaola ka libopeho tse sa tloaelehang.
| Thepa | Tlhaloso |
| Phetiso ea Spectral | 85% bonyane ho tloha ho 635 ho isa ho 690 nanometers |
| Botenya | <1 limilimithara |
| Ho roala | Mahlakore ka bobeli e lokela ho ba anti-reflection e koahetsoeng ho fana ka 1% e bonts'ang haholo ho tloha ho 635 ho isa ho 690 nanometers ka lehlakoreng le leng la fensetere. Sekoaelo se khahlanong le ho bonahatsa se ka fokotsa leseli le hlahang morao ho mokotla oa moamoheli. Liaparo li tla lumellana le litlhoko tsa ho khomarela boima ba MIL-M-13508. |
3-4. Litlhaloso tsa Lifensetere
| Litlhaloso tsa Window bakeng sa Kopanyo ea MT40 | |||||
| Sebaka | Tilt Angle (a) | Bonyane Bongata ba Fesetere | |||
| E tšekaletseng (h) | E otlolohileng (v) | Botenya (t) | |||
| 0 limilimithara (b) | 0 | 0 | 32 limilimithara | 8 limilimithara | <1 limilimithara |
| 10 limilimithara (c) | +20° | <-20° | 40 limilimithara | 11 limilimithara | |
| 20 limilimithara (c) | +12° | <-12° | 45 limilimithara | 13 limilimithara | |
| 30 limilimithara (c) | +8° | <-8° | 50 limilimithara | 15 limilimithara | |
| Litlhaloso tsa Window bakeng sa Kopanyo ea MT40W | |||||
| Sebaka | Tilt Angle (a) | Bonyane Bongata ba Fesetere | |||
| E tšekaletseng (h) | E otlolohileng (v) | Botenya (t) | |||
| 0 limilimithara (b) | 0 | 0 | 32 limilimithara | 8 limilimithara | <1 limilimithara |
| 10 limilimithara (c) | +20° | <-20° | 45 limilimithara | 11 limilimithara | |
| 20 limilimithara (c) | +12° | <-12° | 55 limilimithara | 13 limilimithara | |
| 30 limilimithara (c) | +8° | <-8° | 65 limilimithara | 15 limilimithara | |
Bongata ba fensetere bo tlameha ho eketseha ha bo suthisoa hole le MT40 'me bo lokela ho lekana ho amohela sebaka sa view le lienfelopo tsa khanya tse bontšitsoeng ka tlase:
Boholo ba fensetere bo tlameha ho eketseha ha bo suthisoa hole le MT40W 'me bo lokela ho lekana ho amohela sebaka sa view le lienfelopo tsa khanya tse bontšitsoeng ka tlase:
3-5. Tlhokomelo ea Lifensetere
Karolong ea fensetere, ts'ebetso ea MT40 e tla fokotseha ka lebaka la mofuta ofe kapa ofe oa mofuta. Kahoo, ho fokotsa tšenyo ea fensetere, ho na le lintho tse fokolang tse lokelang ho hlokomeloa.
- Qoba ho ama fensetere haholo joalo ka
- Ha u hloekisa bokaholimo ba fensetere, ka kopo sebelisa lesela le sa chesehang, 'me ka bonolo u hlakole fensetere ea moamoheli ka lesela le seng le fafalitsoe ka mochini o hloekisang likhalase.
MOLAOLI
Enjene ea scan ea MT40 e lumellana le melaoana e latelang:
- Tumellano ea Motlakase - CE EN55022, EN55024
- Tšitiso ea Motlakase - FCC Karolo ea 15 Karolo ea B (Sehlopha sa B)
- Polokeho ea Lifoto - IEC 62471 (Sehlopha se Ikemetseng)
- Melao ea Tikoloho - RoHS 0, WEEE
TS'ELISO TS'OANELO
MARSON MB100 Demo Kit (P/N: 11A0-9801A20) e nolofalletsa nts'etsopele ea lihlahisoa le lits'ebetso tse sebelisang MT40 sethaleng sa MS Windows OS. Ntle le boto ea Multi I/O (P/N: 2006-1007X00), MB100 Demo Kit e fana ka lisebelisoa tsa software le hardware tse hlokahalang bakeng sa ho hlahloba lits'ebetso tsa MT40 pele li li kopanya ho sesebelisoa sa moamoheli. Ka kopo, ikopanye le moemeli oa hau oa thekiso bakeng sa lintlha tsa odara
MB100 Demo Kit Accessories
O: E tšehelitsoe
X: Ha e Tšehetsoe
| Sehokedi Cable | RS232 | USB IPITSE | USB VCP |
| Y-cable ea kantle | o | o | o |
| (P/N: 7090-1583A00) | |||
| Y-cable ea ka hare | o | o | o |
| (P/N: 5300-1315X00) | |||
| Cable ea Micro USB | x | o | o |
| (P/N: 7005-9892A50) |
Ka lebaka la advantagE ea boholo ba eona bo nyane, boto ea MB100 Multi I / O e boetse e loketse ho kenngoa ka har'a sistimi ea moamoheli, joalo ka boto ea sebopeho se hokahanyang MT40 ho sesebelisoa sa moamoheli.
ROBALA MOKHOA
The Mokhoa oa ho robala e lumelloa ke kamehla. Ho lokisa "Nako ea ho Robala", kapa nako ea ho se sebetse pele MT40 e kena Mokhoa oa ho Robala, ka kopo latela mehato e ka tlase.
Mokhoa oa A - Configuration Barcode
Mehato:
- Scan SET MINUTE [.B030$] kapa SET SECOND [.B029$]
- Hlakola linomoro tse peli ho tsoa lethathamong la linomoro tse ka tlase.
- Scan SET MINUTE [.B030$] kapa SET SECOND [.B029$]
Lintlha:
Nako ea Nako ea ho Robala - Metsotso: 0 mets & 1 sec, Max: 60 min & 59 sec (Ho tima Mokhoa oa ho Robala, beha feela 0 mets & 0 sec)
Mokhoa oa B - serial Command
| Thepa | Khetho | Ela hloko |
| Nako ea ho Robala {MT007W3,0} | Nomoro e tsoang ho 0~60 (Minute) Nomoro ho tloha 0~59 (ea bobeli) | Kamehla: 0 motsotso 0 motsotsoana (Tibetsa) Nako ea ho Robala (0 mets & 1 sec ~ 60 min & 59 sec), nako ea ho se sebetse pele scanner e kena Mokhoa oa ho robala. Ho tima Mokhoa oa ho robala, beha feela Nako ea ho Robala joalo ka 0 mets & 0 sec. |
ExampLe:
Romella {MT007W0,10} ho MT40 haeba e le metsotsoana e 10 Nako ea ho Sleep. MT40 e tla khutlisetsa {MT007WOK} ho Host haeba e hlophisitsoe ka katleho.
Lintlha:
- Curly braces "{}" e tlameha ho kenyelletsoa lipheletsong tse peli tsa taelo ka 'ngoe.
- Ho tsosa MT40 ho Mode ea Boroko, romella taelo efe kapa efe kapa u hule tlase ho Trigger pin.
PARAMETER HLOKO
U ka theha MT40 ea hau u sebelisa e 'ngoe ea mekhoa e latelang:
- Tlhophiso ea Barcode:
Skena libarcode tsa tlhophiso ho tsoa ho Buka ea Mosebelisi ea Enjine ea 1D, e fumanehang bakeng sa ho khoasolla ho www.marson.com.tw - Serial Command:
Romela litaelo tsa software ho tsoa ho moamoheli ho latela lenane le felletseng la litaelo tsa software ho Serial Commands Manual, e fumanehang bakeng sa ho jarollwa ho www.marson.com.tw. - Sesebelisoa sa Software:
Sebelisa software e thehiloeng ho PC, Ez Utility®, ho hokahanya le ho lokisa enjene ea scan. E fumaneha hape bakeng sa ho jarollwa ho www.marson.com.tw
TŠEBELETSO PELE
| Moruti. | Letsatsi | Tlhaloso | E hlahisitsoe | E hlahlobiloe |
| 1.0 | 2016.09.08 | Phatlalatso ea Pele | Shaw | Kenji & Hus |
| 1.1 | 2016.09.29 | Metako e ntlafalitsoeng ea Roll/Skew Angle | Shaw | Kenji & Hus |
| 1.2 | 2016.10.31 | Taelo e ntlafalitsoeng ea Mokhoa oa ho Robala Khaolong ea 6 | Shaw | Kenji & Hus |
| 1.3 | 2016.12.23 | E ntlafalitsoe MT40 DOF | Shaw | Kenji & Hus |
| 1.4 | 2017.06.21 | Tlhaloso ea Acrylic Cell Cell-Cast | Shaw | Hus |
| 1.5 | 2017.07.27 | Sekhahla se ntlafalitsoeng sa Scan, ho sebetsa / ho ema hona joale | Shaw | Kenji |
| 1.6 | 2017.08.09 | Mocheso o ntlafalitsoeng oa DOF & Operating/Storage Temp. | Shaw | Kenji & Hus |
| 1.7 | 2018.03.15 | E ntlafalitsoe Khaolo ea 1 le 1-1 ho MCU E ntlafalitsoe Khaolo ea 6 ho litlhophiso tsa Mokhoa oa Taelo. |
Shaw | Kenji & Hus |
| 1.8 | 2018.07.23 | E kentse DOF e Tloaelehileng & DOF e Tiisitsoeng | Shaw | Hus |
| 1.9 | 2018.09.03 | E ntlafalitsoe Khaolo ea 3-4 | Shaw | Hus |
| 2.0 | 2019.04.23 | Setšoantšo se ntlafalitsoeng sa Screw | Shaw | Hus |
| 2.1 | 2020.04.13 | E ntlafalitse DOF e Tloaelehileng le DOF e Tiisitsoeng | Shaw | Hus |
| 2.2 | 2020.10.22 | 1. Mokhoa o ntlafalitsoeng oa ho robala 2. Tlosa Standard & Taelo Mode |
Shaw | Kenji |
| 2.3 | 2021.10.19 | 1. Litšobotsi tse ntlafalitsoeng tsa Motlakase 2. Letšoao la Sehlahisoa se Nchafalitsoeng |
Shaw | Kenji & Alice |
Sehlopha sa Marson Technology Co., Ltd.
9F., 108-3, Minyan Rd., Indian Dist., New Taipei City, Taiwan
MOELE: 886-2-2218-1633
FAX: 886-2-2218-6638
E-mail: info@marson.com.tw
Web: www.marsontech.com
Litokomane / Lisebelisoa
 |
MARSON MT40 Linear Image Barcode Scan Engine [pdf] Tlhophiso Tataiso MT40, MT40W, MT40 Linear Image Barcode Scan Engine, Linear Image Barcode Scan Engine, Barcode Scan Engine, Scan Engine |