Sesebelisoa sa Alamo sa Labkotec GA-2 Grease Separator se nang le li-sensors tse peli

KAKARETSO

GA-2 Grease Alarm ke sesebelisoa sa alamo bakeng sa ho lekola botenya ba lera la grease le bokellanang ka har'a searohanyi sa mafura le ho thibela searola. Tlhahiso e na le GA-2 Grease Alarm control unit, grease alarm sensor GA-SG1, blockage sensor GA-HLL1, le cable joint.

Likarolo tsa tsamaiso

1. GA-SG1 sensor (alamo ea mafura)
2. GA-HLL1 sensor (thibelo)
3. Khokahano ea thapo
4. Sehlopha sa taolo sa GA-2

Sensor ea alamo ea GA-SG1 e kentsoe ka phaposing ea polokelo ea mafura mme e hlokomela botenya ba lera la mafura. Sensor blockage GA-HLL1 e kentsoe ka holim'a kamore ea polokelo ea mafura 'me e laola boemo ba mokelikeli o felletseng oa karohano mme e fana ka alamo ho tsoa ho thibelo e ka bang teng. Lipontšo tsa LED, konopo ea push le li-interface tsa sesebelisoa li hlalositsoe setšoantšong sa 2.

GA-2 SEBELISA LIHLOOHO

1. Letšoao la LED bakeng sa lisebelisoa tse kholo
2. Letšoao la LED bakeng sa sensor ea alamo ea blockage
3. Letšoao la LED bakeng sa sensor ea alamo ea mafura
4. Letšoao la LED bakeng sa phoso
5. Alarm Reset/Lekotsa konopo ea tobetsa
6. Lihokelo tsa alamo ea mafura le li-sensor tsa blockage
7. Liphetho tsa phetisetso molemong oa ho beha leihlo le ho laola.
8. Phepelo voltage

KEKETSO

GA-2 Grease Alarm control unit
Karolo ea taolo ea GA-2 Grease Alarm e ka behoa leboteng. Likoti tse ntseng li hola li fumaneha ka har'a sekoaelo sa sekoaelo, ka tlas'a masoba a ntseng a phahama a sekoahelo se ka pele.
Li-connectors tsa li-conductor tsa ka ntle li arotsoe ka ho arola lipoleiti. Lipoleiti ha lia lokela ho tlosoa. Sekoahelo sa kampetsoeng lokela ho tightened joalo, e le hore metse ka thōko ho ch foreime motheo. Ke ka nako eo feela konopo ea push e sebetsang hantle 'me sebaka se koaletsoeng se tiile. Pele o kenya, ka kopo bala litaelo tsa polokeho khaolong ea 6.

Ho kenya li-sensor
Ho kenngoa ha sensor ho lokela ho etsoa joalokaha ho hlalositsoe setšoantšong sa 3. Sensor ea alamo ea grisi e fana ka alamo ea morao-rao ha e qoelisoa ka ho feletseng ka har'a mafura. Sensor ea blockage e fana ka alamo ea morao-rao ha e qoelisoa ka metsi ka botlalo. Ka kopo, hlahloba botebo bo nepahetseng ba ho kenya hape ho tsoa ho litaelo tsa searohanyi sa mafura.

Lisebelisoa tsa ho kenya
Phano e kenyelletsa motsoako oa cable (setšoantšo sa 4), ho lokisa lisebelisoa (setšoantšo sa 5) bakeng sa ho kenya mochine oa taolo le sensor. Setšoantšong sa 6 ke mohlala oa ho kenyaample ea thapo e nang le hook ea ho fanyeha. Likhokahano tsa mohala oa sensor ka har'a motsoako oa cable li hlalositsoe setšoantšong sa 3. Haeba mohala o sirelelitsoeng o sebelisoa lithebe tsa cable le lithapo tse ka khonehang tse feteletseng li hloka ho hokahanngoa sebakeng se le seng ka ho kopana le galvanic. Tekanyetso ea IP ea motsoako oa cable ke IP68. Etsa bonnete ba hore lenonyeletso la kabel le koetsoe hantle.

TS'EBETSO

Ts'ebetso ea sesebelisoa e lokela ho hlahlojoa kamehla ka mor'a ho kenya. Opereishene e boetse e lokela ho hlahlojoa ka linako tsohle ha u ntša karohano kapa bonyane hang ka likhoeli tse ling le tse ling tse tšeletseng.

Teko ea ts'ebetso
Alamo ea ho thibela (sensor sa blockage GA-HLL1)
Tlhokomeliso: Ha u lekola sensor ea blockage, sensor ea alamo ea mafura e tlameha ho ba ka tankeng e le 'ngoe ea metsi kapa setshelo!

1. Phahamisa sensor holimo moeeng. Sesebelisoa se lokela ho ba ka mokhoa o tloaelehileng (sheba khaolo ea 3.1).
2. Kenya sensor ka metsing. Alamo ea thibelo e lokela ho etsahala (sheba khaolo ea 3.1).
3. Phahamisa sensor holimo moeeng hape. Alamo e lokela ho lla ka mor'a tieho ea metsotsoana e 10.

Teko ea ts'ebetso
Alamo ea ho tlotsa (sensor sa grease GA-SG1)

1. Kenya sensor ka metsing. Sesebelisoa se lokela ho ba ka mokhoa o tloaelehileng (sheba khaolo ea 3.1).
2. Phahamisa sensor holimo moeeng kapa u inele ka har'a grease. Alamo ea mafura e lokela ho hlaha. (sheba khaolo ea 3.1).
3. Kenya sensor hape ka metsing. Alamo e lokela ho lla ka mor'a tieho ea metsotsoana e 10.

Hloekisa li-sensor pele u li khutlisetsa ka har'a karohano. Tlhaloso e qaqileng haholoanyane ea ts'ebetso e fanoe khaolong ea 3.1. Haeba ts'ebetso e sa hlalosoa, ikopanye le moemeli oa moetsi.

Mokhoa oa ts'ebetso
Mokhoa o tloaelehileng ha o na lialamo. Sensor ea alamo ea grisi e ka metsing ka botlalo mme sensor ea blockage e moeeng.

• Letšoao la Mains la LED le butsitsoe.
• Lipontšo tse ling tsa LED li tingoe.
• Li-relay 1 le 2 li na le matla.

Alamo ea ho thibela
Boemo bo fihlile sensor ea blockage. (Sensor e fana ka alamo kapele haholo ha boemo bo le bohareng ba sensor, 'me ea morao-rao ha sensor e qoelisoa ka metsi ka botlalo.)

• Letšoao la Mains la LED le butsitsoe.
• Letšoao la LED la blockage le buletsoe.
• Buzzer e qala ka mor'a tieho ea metsotsoana e 10.
• Relay 2 e lula e le matla.
• Relay 1 e fokotsa matla ka mor'a tieho ea metsotsoana e 10.

Alamo ea mafura
Sensor ea alamo ea mafura e ka har'a mafura. (Sensor e fana ka alamo ea morao-rao ha e qoelisoa ka har'a grease.) (Hlokomela! Alamo e tšoanang e etsahala ha sensor ea alamo ea mafura e le moeeng)

• Letšoao la Mains la LED le butsitsoe.
• Letšoao la LED la alamo ea mafura le butsitsoe.
• Buzzer e qala ka mor'a tieho ea metsotsoana e 10.
• Relay 2 e fokotsa matla ka mor'a tieho ea metsotsoana e 5.

Kamora ho tlosoa ha alamo, li-alarm tsa LED le buzzer li tla tima 'me relay e tla matlafatsoa kamora tieho ea metsotsoana e 10.

Alamo ea phoso
Sensor e robehileng, khefu ea thapo ea sensor kapa potoloho e khuts'oane, ke hore, lets'oao le tlase haholo kapa le phahameng haholo.

• Letšoao la Mains la LED le butsitsoe.
• Sensor circuit Fault LED indicator e buletsoe ka mor'a tieho ea metsotsoana e 10.
• Buzzer e buletsoe kamora tieho ea metsotsoana e 10.
• Relay ea kanale e fapaneng e felloa ke matla ka mor'a tieho ea metsotsoana e 10.

Ho seta alamo bocha
Ha o tobetsa konopo ea Reset push.

• Buzzer e tla tima.
• Li-relay li ke ke tsa fetola boemo ba tsona pele alamo kapa phoso e tima.
• Haeba buzzer e sa hlophisoa bocha, e ikemela ka mor'a matsatsi a mararo.

MOSEBETSI TEKO
Ts'ebetso ea liteko e fana ka alamo ea maiketsetso, e ka sebelisoang ho leka ts'ebetso ea GA-2 Grease Alarm le ts'ebetso ea lisebelisoa tse ling, tse hokahaneng le GA-2 ka li-relay tsa eona.
Tlhokomeliso: Pele o tobetsa konopo ea Test, etsa bonnete ba hore phetoho ea boemo ba relay ha e bake likotsi kae kapa kae!

Boemo bo tloaelehileng
Ha o tobetsa konopo ea Test push:

• Letšoao la Alarm le Fault LED li bulehile hang-hang.
• Buzzer e qala hang hang.
• Li-relay li fokotsa matla ka mor'a metsotsoana e 2 ea ho tobetsa khafetsa.

Ha konopo ea Test push e lokolloa:

• Lits'oants'o tsa LED le buzzer lia tima hang-hang.
• Li-relay li matlafatsa hang-hang.

Alamo ea blockage kapa Grease e buletsoe
Ha o tobetsa konopo ea Test push:

• Lits'oants'o tsa Fault LED li bulehile hang-hang.
• Letšoao la Alarm LED la mocha o tšosang le ntse le le teng 'me relay e fapaneng e lula e se na matla.
• Letšoao la Alamo la LED la mocha o mong le ntse le buletsoe 'me relay ea tima matla.
• Buzzer e ntse e tsoela pele. Haeba e se e setiloe pejana, e tla khutla hore e butsoe.

Ha konopo ea Test push e lokolloa:

• Sesebelisoa se khutlela ntle le tieho ho boemo bo fetileng.

Alamo ya phoso e butswe
Ha o tobetsa konopo ea Test push:

• Sesebelisoa ha se sebetse mabapi le mocha o fosahetseng.
• Sesebelisoa se sebetsa joalo ka ha se hlalositsoe ka holimo mabapi le mocha o sebetsang.

HO BATLE PHOSO

Tlhokomeliso: Ha u lekola sensor ea blockage, sensor ea alamo ea mafura e tlameha ho ba ka tankeng e le 'ngoe ea metsi kapa setshelo!

• Bothata: Ha ho na alamo ha sensor ea alamo ea grease e le mafura kapa moea, kapa alamo e ke ke ea lla
  Lebaka le ka bang teng: Sensor e silafetse.
  Ho etsa: 1. Hloekisa sensor 'me u hlahlobe ts'ebetso hape. Lekanya sensor ea hona joale le voltage, haeba ho hlokahala, joalokaha ho hlalositsoe ka tlase.
• Bothata: Ha ho na alamo ha sensor ea blockage e le mokelikeli, kapa alamo e ke ke ea lla
  Lebaka le ka bang teng: Sensor e silafetse.
  Ho etsa: 1. Hloekisa sensor 'me u hlahlobe ts'ebetso hape. Lekanya sensor ea hona joale le voltage, haeba ho hlokahala, joalokaha ho hlalositsoe ka tlase.
• Tlhokomeliso: Mesebetsi e latelang e tlameha ho etsoa feela ke setsebi sa motlakase se tšoanelehang!
• Bothata: Letšoao la MAINS LED le koetsoe
  Lebaka le ka bang teng: Sesebelisoa ha se fumane matla a motlakasetage.
  Ho etsa: 1. Sheba hore sesebelisoa sa karohano ea matla ha sea tima. 2. Lekanya molumotage pakeng tsa lipalo N le L1. E lokela ho ba 230 VAC ± 10%.
• Bothata: FAULT LED pontshi e butswe
  Lebaka le ka bang teng: Hona joale ho potoloho ea sensor e tlase haholo (cable break or out of connector) kapa e phahame haholo (cable in short circuit). Sensor e kanna ea robeha.
  Ho etsa:
  1. Etsa bonnete ba hore thapo ea kutlo e hokahantsoe ka nepo ho yuniti ea taolo ea GA-2.
  2. Lekanya bophahamo ba modumotage ka thoko pakeng tsa lipalo 10 le 11 hammoho le 13 le 14. The voltage lokela ho ba pakeng tsa 7,0 - 8,5 V. Hlokomela! Molumotage fapanyetsana pakeng tsa li-connectors tsa sensor ka nako ea metsotsoana e 1.
  3. Lekanya hona joale ha sensor e le moeeng kapa ka grease. Nako e lekantsoeng e lokela ho ba 7,0 8,5 mA.
  4. Lekanya hona joale ha sensor e le ka metsing. Hona joale e lekantsoeng e lokela ho ba 2,5 3,5 mA
     Haeba mathata a ke ke a rarolloa ka litaelo tse ka holimo, ka kopo ikopanye le mohoeletsi oa lehae oa Labkotec Oy kapa tšebeletso ea Labkotec Oy.

TOKISO LE TŠEBELETSO

Li-sensor li lokela ho hloekisoa, 'me ts'ebetso ea sesebelisoa sa alamo e lokela ho lekoa ha ho tšolloa kapa ho boloka sekhetho sa mafura kapa bonyane hang ka likhoeli tse ling le tse ling tse tšeletseng. Bakeng sa ho hloekisa, ho ka sebelisoa sesepa se bonolo (mohlala, metsi a hlatsoang) le borashe ba ho hohla.
Ha ho na le lipotso, ka kopo ikopanye le litšebeletso tsa Labkotec Oy.

TŠIRELETSO LITS'ELISO

• Sesebelisoa ha se kenyelle sesebelisoa sa motlakase. Mochine o motlakase oa lipalo tse peli (250 VAC 1 A), o arolang mela e 'meli (L1, N) e tlameha ho kenngoa methapong e meholo ea phepelo ea motlakase haufi le yuniti. Phetoho ena e nolofatsa ts'ebetso ea tlhokomelo le lits'ebeletso mme e tlameha ho tšoauoa ho khetholla unit. Fuse boholo ba 10 A.
• Haeba ho hlokahala ho buloa ha sekoaelo sa ntlo, ke ramotlakase ea lumelletsoeng feela ea lumeletsoeng ho kenya kapa ho hlokomela sesebelisoa.
• Haeba sesebelisoa se sebelisoa khahlano le litaelo tsa moetsi, tšireletso e fanoeng ke sesebelisoa e ka senyeha.
• Sesebelisoa ha se lumelloe ho kenya libakeng tse kotsi.

LIEKETSENG MOTS'OANE

Sehlopha sa taolo sa GA-2
Litekanyo	125 mm x 75 mm x 35 mm (lxhxd)
Boima ba 'mele	250 g Sephutheloana sa 1,2 kg (li-control unit + 2 sensors + cable joint)
Sebaka se koaletsoeng	IP 65, polykarbonate ea lintho tse bonahalang
Lihlahla tsa cable	4 likhomphutha M16 bakeng sa kabel bophara 5-10 limilimithara
Tikoloho ya tshebetso	Mocheso: -30 ºC…+50 ºC Max. bophahamo ka holim'a bophahamo ba leoatle 2,000 m Mongobo o amanang RH 100% E loketse ts'ebeliso ea kahare le kantle (e sirelelitsoeng puleng e tobileng)
Phepelo voltage	230 VAC ± 10%, 50/60 Hz Sesebelisoa ha se na sesebelisoa sa motlakase. Fuse boholo ba 10 A.
Tšebeliso ea matla	5 VA
Tlhahiso ea relay	Li-pcs tse 2 tse ka bang mahala tsa relay 250 V, 5 A Ho lieha ho sebetsa 10 sec. Relay de-energize at trigger point.
Tšireletseho ea motlakase	EN IEC 61010-1, Sehlopha sa II , CAT II, ​​POLLUTION DEGREE 2
EMC Emission Immunity	EN IEC 61000-6-3 EN IEC 61000-6-1
Selemo sa tlhahiso: Ka kopo, bona nomoro ea serial ho mofuta oa poleiti	xxxxxxxxxx YY x moo YY = selemo sa tlhahiso (mohlala 19 = 2019)

Li-sensor tsa GA-SG1 le GA-HLL1
Molao-motheo oa ts'ebetso	Capacitive
Lintho tse bonahalang	POM, rabara ea chlorinated polyethylene (CM), AISI 316
Boima ba 'mele	350 g (sensor + thapo e tsitsitseng)
Sehlopha sa IP	IP68
Mocheso oa ts'ebetso	0 ºC…+90 ºC
Cable	Cable e tsitsitseng 2 x 0,75 mm2 Ø 5,8mm. Bolelele bo tloaelehileng ke 5 m, bolelele bo bong ke boikhethelo. The max. bolelele ba thapo e tsitsitseng ke 15 m, e ka atolosoa. Boholo ba khanyetso ea loop ea cable ke 75Ω.
EMC Emission Immunity	EN IEC 61000-6-3 EN IEC 61000-6-1
Selemo sa tlhahiso: Ka kopo bona nomoro ea serial ho tloha tlase ho sensor	GAxxxxYY / GAHxxxxxYY   moo YY = selemo sa tlhahiso (mohlala 19 = 2019)

PHATLATSO EA EU EA TUMELO
Ka hona, re phatlalatsa hore sehlahisoa se boletsoeng ka tlase se etselitsoe ho latela litlhoko tse amehang tsa litaelo le maemo a boletsoeng.

• Sehlahisoa: Ho lekanya le ho laola likarolo le li-sensor
  • Setsi sa Taolo ea Alamo ea GA-1
  • Setsi sa Taolo ea Alamo ea GA-2
  • Sensor ea GA-SG1
  • Sensor ea GA-HLL1
• Moetsi: Labkotec Oy Myllyhaantie 6 FI-33960 Pirkkala Finland
• Litaelo: Sehlahisoa se lumellana le Litaelo tse latelang tsa EU:
  • 2014/30/EU Electromagnetic Compatibility Directive (EMC)
  • 2014/35 / EU Low VoltagDirective (LVD)
  • 2011/65/EU Restriction of Hazardous Substances Directive (RoHS)
• Maemo: Ho ile ha sebelisoa litekanyetso tse latelang:
  • EMC:
  • EN IC 61000-6-1:2019
  • EN IEC 61000-6-3: 2021
  • EN IEC 61000-3-2: 2019
  • EN 61000-3-3:2013/A1:2019
  • LVD: EN 61010-1:2010/A1:2019/AC:2019-04
  • ROHS: EN IEC 63000:2018

Labkotec Oy
Eketsa: Myllyhaantie 6, FI-33960 Pirkkala, Finland
Mohala +358 29 006 260
E: info@labkotec.fi

Litokomane / Lisebelisoa

Sesebelisoa sa Alamo sa Labkotec GA-2 Grease Separator se nang le li-sensors tse peli [pdf] Buka ea Taelo Sesebelisoa sa Alarm sa GA-2 Grease Separator se Nang le Li-Sensors tse peli, GA-2, Sesebelisoa sa Alamo sa Grease Separator se nang le li-Sensors tse peli, Sepharator Alarm Device e nang le li-sensors tse peli, sesebelisoa sa alamo se nang le li-sensors tse peli, tse nang le li-sensors tse peli, li-sensor tse peli.

Litšupiso

• Bukana ea Mosebelisi