BAFANG DP C262.CAN Pontšo
BOHLOKOA TSEBISO
- Haeba lintlha tsa phoso tse hlahang skrineng li ke ke tsa lokisoa ho latela litaelo, ka kopo ikopanye le morekisi oa hau.
- Sehlahisoa se etselitsoe ho thibela metsi. Ho khothalletsoa haholo ho qoba ho qoelisa pontšo ka tlas'a metsi.
- Se ke oa hloekisa ponts'o ka jet ea mouoane, sehloekisi sa khatello e phahameng kapa hose ea metsi.
- Ka kopo sebelisa sehlahisoa sena ka hloko.
- Se ke oa sebelisa li-thiners kapa li-solvents tse ling ho hloekisa skrineng. Lintho tse joalo li ka senya bokaholimo.
- Warranty ha e kenyelelitsoe ka lebaka la ho apara le tšebeliso e tloaelehileng le botsofali.
SELELEKELA PONTŠO
- Mohlala: DP C262.CAN BUS
- Thepa ea matlo ke ABS, sekoaelo le fensetere li entsoe ka khalase ea soda-lime, konopo ke lisebelisoa tsa TPV, tse latelang:
- Letšoao la li-label ke ka tsela e latelang:
Hlokomela: Ka kopo, boloka leibole ea khoutu ea QR e khomaretsoe thapong ea pontšo. Lintlha tse tsoang ho Leibole li sebelisoa molemong oa ntlafatso ea software e ka bang teng hamorao.
TLHALOSO EA SEHLAHISOA
Litlhaloso
- Mocheso oa ho sebetsa: -20 ℃ ~ 45 ℃
- Mocheso oa polokelo: -20 ℃ ~ 60 ℃
- Ha e kenelle metsi: IP65
- Ho beha mongobo: 30-70% RH
E sebetsa hapeview
- Sesupo sa lebelo (ho kenyeletsoa lebelo la nako ea nnete, lebelo le holimo le lebelo le tloaelehileng)
- Yuniti e fetoha pakeng tsa km le mile.
- Pontšo ea matla a betri
- Taolo le pontšo bakeng sa lebone la pele
- Pontšo ea boemo ba thuso
- Pontšo ea leeto (ho kenyeletsoa TRIP, ODO le RANGE)
- Pontšo ea matla a enjene (ho kenyeletsoa matla a ho kenya enjene, matla a kentsoeng a motho)
- Pontsho ya nako bakeng sa ho palama o le mong
- Mohlala oa thuso ea maoto
- Pontšo ea melaetsa ea liphoso
- Sesupo sa tšebeliso ea matla a CALORIES (HLOKOMELA: Haeba molaoli a na le ts'ebetso ena)
- Pontsho bakeng sa sebaka se setseng. (HLOKOMELA: e hloka hore molaoli o na le ts'ebetso ena)
BONTS'A LITABA
- Pontsho ya lebone la hlooho
- Pontsho ya lebelo ka nako ya nnete
- Khetho ea mokhoa:
leeto le le leng la leeto (TRIP), kakaretso ea sebaka
ODO, lebelo le phahameng (MAX), lebelo le tloaelehileng
(AVG), sebaka se setseng (RANGE), matla
tshebediso (KALORI), nako (NAKO). (Hlokomela:
ts'ebetso e ts'oanang e hloka litšehetso tsa Molaoli). - Sesupo sa boemo ba tšehetso le thuso ea ho tsamaea
- Pontšo ea matla a betri
- Pontšo ea "tšebeletso".
- Pontšo ea yuniti ea lebelo
- Pontšo ea ho kenya motlakase
- Pontšo ea ho kenya matla a motho
TLHALOSO SEHLOHO
TLOAELEHILE TS'EBE
Ho fetola Sisteme HO ON/OFF
Tobetsa 
'me u tšoare (> 2S) ho kenya matla skrineng, HMI e qala ho bonts'a boot up LOGO. Tobetsa 'me u tšoare (> 2S) hape e ka tima HMI.
Khetho ea Maemo a Thuso
Ha HMI e butse, tobetsa hakhutšoanyane 
(<0.5s) kapa 
ho khetha boemo ba thuso (palo ea boemo ba thuso e lokela ho fetoloa ho molaoli), Boemo bo tlase ka ho fetisisa ke Boemo ba 0, Boemo bo phahameng ka ho fetisisa ke ba 5. Boemong ba kamehla ke Level 1, "0" e bolela hore ha ho thuso ea matla. The interface ke e latelang:
Khetho ea Mokhoa
Tobetsa ka bokhutšoanyane konopo ea "Mode" (<0.5s) ho view mekhoa le litaba tse fapaneng.
- Sistimi e nang le sensor ea torque, e potolohang e bonts'a sebaka sa leeto le le leng (Leeto,km) → kakaretso ea sebaka (ODO,km) → lebelo le phahameng (MAX,km/h) → lebelo le tloaelehileng (AVG,km/h) → sebaka se setseng (RANGE,km ) → molumo (CADENCE) → tšebeliso ea matla (KALORI/CAL,KCal) → nako ea ho palama (NAKO,mots) → potoloho.
- Haeba sistimi e nang le sensor ea lebelo, ka potoloho e bonts'a sebaka se le seng sa leeto (Leeto,km) → kakaretso ea sebaka (ODO,km) → lebelo le phahameng (MAX,km/h) → lebelo le tloaelehileng (AVG,km/h) → sebaka se setseng (RANGE ,km) → nako ea ho palama (NAKO, mots) → potoloho.
Mabone a hlooho / backlighting
Tobetsa o hatelle (> 2S) ho bonesa lebone la morao hammoho le lebone la pele.
Tobetsa o hatelle (> 2S) hape ho tima lebone la morao le lebone la hlooho.
Tsamaea Thuso
Ha Pedelec ea hau e sa sisinyehe, tobetsa hakhutšoanyane konopo ho fihlela ho Walk assistance indicator 
e bontshwa. Ka nako ena, tobetsa nako e telele konopo, Pedelec e kenya mokhoa oa ho thusa ho tsamaea, letšoao le tla khanya. Haeba ho lokolla konopo e tla emisa sena, haeba ho se na ts'ebetso ka har'a 5s e tla khutlela boemong ba 0 ka bo eona. Seo se emisitsoe ho mokhoa oa Walk help.(joalo ka ho latela)
Pontšo ea Bokhoni ba Battery
Palotage ea matla a hona joale a betri le kakaretso ea kakaretso e bonts'oa ho tloha ho 100% ho isa ho 0% ho ea ka matla a sebele (joalokaha ho bontšitsoe setšoantšong se ka tlase).
Tshebeletso
HMI e tla kopa ho lokisoa ho latela mileage le linako tsa tjhaja ea betri. Ha sebaka sa leeto se feta 5000km (makhetlo a 100 bakeng sa tjhaja) 'me mosebetsi oa "Tšebeletso" o buletsoe, letšoao la "Tšebeletso" le tla hlahisoa ho HMI. Mosebetsi ona o ka behoa ka har'a sehokelo. Bakeng sa tshebetso e hlalositsoe ka ho qaqileng ka mongolo o latelang.
LIEKETSENG
Kamora hore HMI e bulela, tobetsa hakhutšoanyane konopo ea "Mode" makhetlo a mabeli ho kena "Setting". Tobetsa ka bokhutšoanyane kapa (<0.5s) ho khetha ebe o tobetsa hakhutšoanyane (<0.5S) "Mode" konopo ho netefatsa le ho kenya khetho.
Ela hloko: lebelo e lokela ho ba "0" ka nako eo o ka kenya segokanyimmediamentsi sa sebolokigolo.
U ka tobetsa ka potlako konopo ea "Mode" (<0.5S) habeli ka nako efe kapa efe, kapa khetha "Back" kapa "Exit" ho tsoa ho khutlela sebopeho se seholo.
"Setting" segokanyimmediamentsi sa sebolokigolo
Ho "Setting" interface, tobetsa hakhutšoanyane (<0.5S) kapa ho khetha "Setting" ebe o tobetsa ka bokhutšoanyane (<0.5S) "Mode" ho netefatsa le ho kena "Setting".
“Trip Reset”—seta tshebetso bakeng sa leeto le le leng
Tobetsa ka bokhutšoanyane or ho khetha "Trip Reset", ebe o tobetsa "Mode" ka bokhuts'oane ho kenya ntho eo. Khetha "NO"/"YES" ("YES"- ho hlakola, "NO" -ha ho ts'ebetso), ebe o tobetsa "Mode" ka bokhuts'oane ho boloka le ho tsoa hape ho "Setting" interface.
HLOKOMELA: nako ea ho palama baesekele, lebelo le tloaelehileng le lebelo le phahameng li setiloe bocha ka nako e le 'ngoe.
“Yuniti”—seta yuniti bakeng sa km/mile
Tobetsa ka bokhutšoanyane or ho khetha "Unit", ebe o tobetsa "Mode" ka bokhuts'oane ho kenya ntho eo. Khetha "Metric"/ "Imperial", ebe o tobetsa "Mode" ka bokhutšoanyane ho boloka le ho tsoa ho "Setting" interface.
"Khanya" - beha khanya ea backlight
Tobetsa ka bokhutšoanyane or ho khetha "Khanya", ebe o tobetsa "Mode" ka bokhuts'oane ho kenya ntho eo. Khetha palotage le "100%"/ "75%"/"50%"/"30%"/"10%", ebe o tobetsa "Mode" hakhutšoanyane ho boloka le ho tsoa ho khutlela ho "Setting" interface.
Hlokomela: "10%" ke khanya e tlase mme 100% ke khanya e phahameng ka ho fetisisa.
“Auto Off”—seta nako ya ho tima ya othomathike
Tobetsa ka bokhutšoanyane or ho khetha "Auto Off", ebe o tobetsa "Mode" hakhutšoanyane ho kenya ntho eo. Khetha nako ea ho tima e le "OFF"/"9"/"8"/"7"/"6"/"5"/"4"/"3"/"2"/"1", tobetsa "Mode" hakhutšoanyane. ” ho boloka litlhophiso ebe o tsoa o khutlela sebopehong sa "Setting".
Tlhokomeliso: "TLOA" e bolela hore ts'ebetso ena e koetsoe, yuniti ke motsotso.
“Assist Mode”—seta boemo ba thuso
Tobetsa ka bokhutšoanyane or ho khetha "Assist Mode", ebe o tobetsa "Mode" hakhutšoanyane ho kenya ntho eo. Khetha boemo ba thuso e le "3"/"5"/9", ebe o tobetsa "Mode" hakhutšoanyane ho boloka le ho tsoa ho "Setting" interface.
"Tšebeletso" - bulela / tima pontšo ea Tšebeletso
Tobetsa ka bokhutšoanyane or ho khetha "Tšebeletso", ebe o tobetsa "Mode" ka bokhutšoane ho kenya ntho eo. Kgetha “NO”/“YES” (“YES” ho bolela hore letshwao la Tshebeletso le butswe; “NO” ho bolela hore letshwao la Tshebeletso le timilwe), ebe o tobetsa “Mode” ka bokgutshwane ho boloka le ho tswa ho kgutlela sebopehong sa “Setting”.
Sehokelo sa "Boitsebiso".
Ho Setting interface, tobetsa hakhutšoanyane (<0.5S) or ho khetha "Information" ebe o tobetsa ka bokhutšoanyane (<0.5S) "Mode" ho netefatsa le ho kenya "Information".
View “Boholo ba Lebili”
Tobetsa ka bokhutšoanyane or ho khetha "Wheel Size", ebe o tobetsa "Mode" ka bokhuts'oane ho view lebili saese ya kamehla, ebe ka bokhuts'oane tobetsa "Mode" ho tsoa khutlela ho "Information" segokanyimmediamentsi sa sebolokigolo.
View "Tekanyetso ea Lebelo"
Tobetsa ka bokhutšoanyane or ho khetha "Speed Limit", ebe o tobetsa "Mode" ho view "Mode" o tobetsa "Mode" ho tsoa ho "Information" interface.
View "Lintlha tsa Battery."
Tobetsa ka bokhutšoanyane or ho ea ho "Info ea Battery.", ebe o tobetsa "Mode" hakhutšoanyane ho kenya, ebe o tobetsa "+" kapa "-" ka bokhutšoanyane. view lintlha tsa betri (b01 → b04 → b06 → b07 → b08 → b09 → b10 → b11 → b12 → b13 → d00 → d01 → d02 → … → dn → Hardware Ver → Software Ver), ebe o tobetsa "Mode" hakhutšoanyane ho tsoa ho sebopeho sa "Information".
Tlhokomeliso: Haeba betri e se na tšebetso ea puisano, u ke ke ua bona data efe kapa efe e tsoang ho betri.
| Khoutu | Tlhaloso ea Khoutu | Yuniti |
| b01 | Mocheso oa hona joale | ℃ |
| b04 | Kakaretso ea voltage | mV |
| b06 | Karolelano ea hona joale | mA |
| b07 | Bokhoni bo setseng | mAh |
| b08 | Bokhoni ba betri ea ho tjhaja ka botlalo | mAh |
| b09 | Relative Charge ka liperesentetage | % |
| b10 | Tefiso e felletseng ka liperesentetage | % |
| b11 | Linako tsa Cycle | linako |
| b12 | Nako ea ho Tlosa Nako e telele | Hora |
| b13 | Nako ea ho Qetela ea ho Khaola | Hora |
| d00 | Palo ea sele | |
| d01 | Moqtage Cell1 | mV |
| d02 | Moqtage Cell2 | mV |
| dn | Moqtage Cell n | mV |
| e01 | Hardware Version | |
| e02 | Software Software |
HLOKOMELA: Haeba ho se na data e fumanoeng, e tla hlahisa "-".
View "Lintlha tse bonts'ang"
Tobetsa ka bokhutšoanyane or ho khetha "Display Info", ebe o tobetsa ka bokhutšoanyane "Mode" ho view eona, tobetsa hakhutšoanyane or ho view "Hardware Ver" kapa "Software Ver", ebe o tobetsa "Mode" ka bokhuts'oane ho tsoa ho khutlela sebopeho sa "Information".
View "Ctrl Info"
Tobetsa ka bokhutšoanyane or ho khetha "Ctrl Info", 'me joale tobetsa ka bokhutšoanyane "Mode" ho view eona, tobetsa hakhutšoanyane or ho view "Hardware Ver" kapa "Software Ver", ebe o tobetsa "Mode" ka bokhuts'oane ho tsoa ho khutlela sebopeho sa "Information".
View "Litaba tsa Torque"
Tobetsa ka bokhutšoanyane or ho khetha "Torque Info", 'me ka nako eo tobetsa ka bokhutšoanyane "Mode" ho view eona, tobetsa hakhutšoanyane or ho view "Hardware Ver" kapa "Software Ver", ebe o tobetsa "Mode" ka bokhuts'oane ho tsoa ho khutlela sebopeho sa "Information".
HLOKOMELA: Haeba Pedelec ea hau e se na sensor ea torque, joale "Torque Info" e ke ke ea hlahisoa.
View "Error Code"
Tobetsa ka bokhutšoanyane or ho khetha "Error Code", ebe o tobetsa "Mode" ka bokhutšoane ho view eona, tobetsa hakhutšoanyane or ho view molaetsa oa phoso makhetlo a leshome a ho qetela ka "E-Code0" ho "E-Code9", ebe o tobetsa "Mode" ka bokhuts'oane ho tsoa ho "Information" interface.
HLOKOMELA: 00 e bolela hore ha ho na phoso e teng.
View "Temoso Code"
Tobetsa ka bokhutšoanyane or ho khetha "Warn Code", ebe o tobetsa ka bokhuts'oane "Mode" ho view eona, tobetsa hakhutšoanyane or ho view molaetsa oa temoso bakeng sa makhetlo a leshome a ho qetela ka "W-Code0" ho "W-Code9", ebe o tobetsa "Mode" hakhutšoanyane ho tsoa ho "Information" interface.
PHOSO TLHALOSO
HMI e ka bonts'a liphoso tsa Pedelec. Ha phoso e fumanoa, e 'ngoe ea likhoutu tse latelang tsa phoso e tla bontšoa sebakeng sa pontšo ea lebelo.
Tlhokomeliso: Ka kopo bala ka hloko tlhaloso ea khoutu ea phoso. Ha khoutu ea phoso e hlaha, ka kopo qala ka ho qala sistimi hape. Haeba bothata bo sa felisoe, ka kopo ikopanye le morekisi oa hau kapa basebetsi ba tekheniki.
| Phoso | Phatlalatso | Ho batle phoso |
| 04 | The throttle e na le phoso. |
|
| 05 | The throttle ha e khutlele sebakeng sa eona se nepahetseng. | Sheba hore sehokelo ho tloha ho throttle se amana hantle. Haeba sena se sa rarolle bothata, ka kopo fetola throttle. |
| 07 | Ho tlolatage tshireletso |
|
| 08 | Phoso le lets'oao la sensor ea holo kahare ho enjene |
|
| 09 | Phoso le karolo ea Enjine | Ka kopo fetola enjene. |
| 10 | Mocheso ka hare ho enjene o fihlile boleng ba eona bo phahameng ba tšireletso |
|
| 11 | Sensor ea mocheso ka hare ho enjene e na le phoso | Ka kopo fetola enjene. |
| 12 | Phoso le sensor ea hajoale ho molaoli | Ka kopo fetola molaoli kapa ikopanye le mofani oa thepa ea hau. |
| 13 | Phoso ka sensor ea mocheso ka hare ho betri |
|
| 14 | Mocheso oa tšireletso ka hare ho molaoli o fihlile boleng ba eona bo phahameng ba tšireletso |
|
| 15 | Phoso e nang le sensor ea mocheso ka hare ho molaoli |
|
| 21 | Phoso ea sensor ea lebelo |
|
| 25 | Phoso ea lets'oao la torque |
|
| 26 | Letšoao la lebelo la sensor ea torque le na le phoso |
|
| 27 | Overcurrent ho tloha ho molaoli | Ho sebelisa sesebelisoa sa BESST nchafatsa molaoli. Haeba bothata bo ntse bo etsahala, ka kopo fetola molaoli kapa ikopanye le mofani oa thepa ea hau. |
| 30 | Bothata ba puisano |
|
| 33 | Letšoao la brake le na le phoso (Haeba li-sensor tsa brake li kentsoe) |
Haeba bothata bo tsoela pele Ka kopo fetola molaoli kapa ikopanye le mofani oa thepa ea hau. |
| 35 | Potoloho ea 15V e na le phoso | U sebelisa sesebelisoa sa BESST ntlafatsa molaoli ho bona hore na sena se rarolla bothata. Haeba ho se joalo, ka kopo fetola molaoli kapa ikopanye le mofani oa thepa ea hau. |
| 36 | Potoloho ea ho lemoha letlapeng la likonopo e na le phoso | U sebelisa sesebelisoa sa BESST ntlafatsa molaoli ho bona hore na sena se rarolla bothata. Haeba ho se joalo, ka kopo fetola molaoli kapa ikopanye le mofani oa thepa ea hau. |
| 37 | Potoloho ea WDT e fosahetse | U sebelisa sesebelisoa sa BESST ntlafatsa molaoli ho bona hore na sena se rarolla bothata. Haeba ho se joalo, ka kopo fetola molaoli kapa ikopanye le mofani oa thepa ea hau. |
| 41 | Kakaretso ea voltage ho tsoa betri e phahame haholo | Ka kopo fetola betri. |
| 42 | Kakaretso ea voltage tsoang betri e tlase haholo | Ka kopo tjhaja betri. Haeba bothata bo ntse bo etsahala, ka kopo fetola betri. |
| 43 | Kakaretso ea matla a tsoang liseleng tsa betri e phahame haholo | Ka kopo fetola betri. |
| 44 | Moqtage ea sele e le 'ngoe e phahame haholo | Ka kopo fetola betri. |
| 45 | Mocheso oa betri o phahame haholo | Ka kopo tlohela pedelec hore e phomole. Haeba bothata bo ntse bo hlaha, ka kopo fetola betri. |
| 46 | Thempereichara ea betri e tlase haholo | Ka kopo tlisa betri mochesong oa kamore. Haeba bothata bo ntse bo etsahala, ka kopo fetola betri. |
| 47 | SOC ea betri e phahame haholo | Ka kopo fetola betri. |
| 48 | SOC ea betri e tlase haholo | Ka kopo fetola betri. |
| 61 | Ho fetola bothata ba ho lemoha |
|
| 62 | Electronic derailleur ha e khone ho lokolla. | Ka kopo fetola derailleur. |
| 71 | Senotlolo sa elektroniki se koalehile |
|
| 81 | Bluetooth module e na le phoso | U sebelisa sesebelisoa sa BESST, nchafatsa software hape skrineng ho bona hore na e rarolla bothata. Haeba ho se joalo, Ka kopo fetola ponts'o. |
TEMOSO KHOUTU TLHALOSO
| Hlokomela | Phatlalatso | Ho batle phoso |
| 28 | Ho qala ha sensor ea torque ha hoa tloaeleha. | Qala sistimi hape 'me u hlokomele hore u se ke oa hata ka thata ha u qala. |
Litokomane / Lisebelisoa
 |
BAFANG DP C262.CAN Pontšo [pdf] Bukana ea Mosebelisi Pontšo ea DP C262.CAN, Pontšo ea C262.CAN, Pontšo |
