BAFANG DP C262.CAN zaub

Cov ntsiab lus zais
1 TSEEM CEEB
2 INTRODUCTION OF DISPLAY
3 KHOOM PLIG
3.1 Specifications
3.2 Muaj nuj nqi Tshajview
4 QHIA PAUB TXOG
5 TSEEM CEEB
6 IB TUG NEEG
6.1 Hloov qhov System ON/OFF
6.2 Xaiv Cov Qib Pab
6.3 Xaiv hom
6.4 Headlights / backlighting
6.5 Taug kev pab
6.6 Roj teeb muaj peev xwm qhia tau
6.7 Kev pabcuam
7 SETTINGS
7.1 "Setting" interface
7.2 "Cov ntaub ntawv" interface
8 YUS CODE DEFINITION
9 WARN CODE DEFINITION
10 Cov ntaub ntawv / Cov ntaub ntawv
10.1 Cov ntaub ntawv
11 Related Posts

TSEEM CEEB

  • Yog tias cov ntaub ntawv yuam kev los ntawm cov zaub tsis tuaj yeem raug kho raws li cov lus qhia, thov hu rau koj lub khw muag khoom.
  • Cov khoom yog tsim los ua kom tsis muaj dej. Nws raug nquahu kom tsis txhob submerging cov zaub hauv qab dej.
  • Tsis txhob ntxuav cov zaub nrog lub dav hlau dav hlau, lub tshuab nqus tsev siab los yog cov kav dej.
  • Thov siv cov khoom no nrog kev saib xyuas.
  • Tsis txhob siv cov thinners lossis lwm cov kuab tshuaj los ntxuav cov zaub. Cov tshuaj zoo li no tuaj yeem ua rau lub ntsej muag puas.
  • Warranty tsis suav nrog vim hnav thiab siv li qub thiab kev laus.

INTRODUCTION OF DISPLAY

  • Qauv: DP C262.CAN BUS
  • Cov khoom siv hauv tsev yog ABS, lub hau npog thiab lub qhov rais yog tsim los ntawm cov iav dej qab zib, lub pob yog cov khoom siv TPV, raws li hauv qab no:
  • Daim ntawv cim npe yog raws li nram no:

Nco tseg: Thov khaws daim ntawv lo QR code txuas nrog rau cov zaub cable. Cov ntaub ntawv los ntawm Label yog siv rau kev hloov kho software tom qab.

KHOOM PLIG

Specifications
  • Ua haujlwm kub: -20 ℃ ~ 45 ℃
  • Cia kub: -20 ℃ ~ 60 ℃
  • Waterproof: IP65
  • Bearing humidity: 30% -70% RH
Muaj nuj nqi Tshajview
  • Kev qhia ceev (nrog rau lub sijhawm ceev ceev, max. ceev thiab nruab nrab ceev)
  • Chav tsev hloov ntawm km thiab mais.
  • Roj teeb muaj peev xwm qhia tau
  • Tswj thiab taw qhia rau lub taub hau
  • Qhia txog qib kev pab
  • Kev taw qhia txog kev mus ncig (nrog rau TRIP, ODO thiab RANGE)
  • Lub cev muaj zog qhov taw qhia (nrog rau lub cev muaj zog input zog, tib neeg lub zog input)
  • Lub sijhawm qhia rau kev caij tsheb ib leeg
  • Taug kev pab qauv
  • Kev taw qhia rau cov lus yuam kev
  • Kev taw qhia txog kev siv hluav taws xob CALORIES (CEEB TOOM: Yog tias tus maub los muaj txoj haujlwm no)
  • Kev taw qhia rau qhov kev ncua deb. (CEEB TOOM: nws xav tau tus maub los muaj txoj haujlwm no)

QHIA PAUB TXOG

  1. Headlight qhia
  2. Ceev zaub hauv real-time
  3. Hom kev xaiv:
    ib leeg-trip nrug (TRIP), tag nrho nrug
    ODO, siab tshaj plaws ceev (MAX), nruab nrab ceev
    (AVG), seem nrug (RANGE), zog
    noj (CALORIES), sij hawm (TIME). (Nco tseg:
    tib lub luag haujlwm xav tau tus Controller txhawb).
  4. Kev them nyiaj yug theem thiab qhov taw qhia kev pab taug kev
  5. Roj teeb muaj peev xwm qhia tau
  6. "Service" qhia.
  7. Kev ntsuas ntsuas ntsuas
  8. Lub cev muaj zog input indication
  9. Human zog input indication

TSEEM CEEB

IB TUG NEEG

Hloov qhov System ON/OFF

Xovxwm thiab tuav (> 2S) rau lub zog ntawm cov zaub, HMI pib qhia lub khau raj LOGO. Xovxwm thiab tuav (> 2S) rov tuaj yeem tua HMI.

Xaiv Cov Qib Pab

Thaum HMI qhib, nias luv luv (<0.5s) los yog xaiv cov qib kev pab (tus naj npawb ntawm qib kev pab yuav tsum tau yoog raws li tus tswj), qib qis tshaj yog Qib 0, qib siab tshaj plaws yog 5. Ntawm lub neej ntawd yog Theem 1, “0” txhais tau tias tsis muaj kev pab fais fab. Lub interface yog raws li nram no:

Xaiv hom

Luv luv nias "Hom" khawm (<0.5s) rau view hom sib txawv thiab cov ntaub ntawv.

  1. Qhov system nrog lub zog torque, ncig qhia ib ncig mus ncig (Trip, km) → tag nrho nrug (ODO, km) → siab tshaj plaws (MAX, km / h) → nruab nrab ceev (AVG, km / h) → seem nrug (RANGE, km ) → cadence (CADENCE) → kev siv hluav taws xob (CALORIES/CAL, KCal) → caij caij (TIME, min) → voj voog.
  2. Yog hais tias lub kaw lus nrog lub sensor ceev, ncig qhia ib ncig mus ncig (Trip, km) → tag nrho nrug (ODO, km) → siab tshaj plaws (MAX, km / h) → nruab nrab ceev (AVG, km / h) → seem nrug (RANGE , km) → caij lub sij hawm (TIME, min) → voj voog.
Headlights / backlighting

Nias thiab tuav (> 2S) tig lub teeb rov qab thiab lub teeb taub hau.
Nias thiab tuav (> 2S) rov tua lub teeb rov qab thiab lub teeb taub hau.

Taug kev pab

Thaum koj lub Pedelec tsis muaj zog, nias luv luv khawm kom txog thaum qhov taw qhia kev pab taug kev yog tso tawm. Ntawm no, ntev nias khawm, lub Pedelec nkag mus rau txoj kev pab hom, qhov taw qhia yuav flash. Yog tias tso lub pob yuav nres qhov no, yog tias tsis muaj kev ua haujlwm hauv 5s yuav rov qab mus rau qib 0. Qhov ntawd raug tso tseg los ntawm Kev Pabcuam Taug Kev.(raws li hauv qab no)

Roj teeb muaj peev xwm qhia tau

Qhov percentage ntawm tam sim no lub roj teeb muaj peev xwm thiab tag nrho lub peev xwm yog tso tawm los ntawm 100% mus rau 0% raws li lub peev xwm tiag tiag (raws li qhia hauv daim duab hauv qab no).

Kev pabcuam

HMI yuav ceeb toom rau kev saib xyuas raws li lub caij nyoog thiab lub sijhawm them roj teeb. Thaum mileage tshaj 5000km (100 zaug rau charger) thiab "Service" muaj nuj nqi yog enabled, "Service" indications yuav tshwm nyob rau hauv HMI. Cov haujlwm no tuaj yeem teeb tsa hauv lub interface. Rau kev ua haujlwm tau piav qhia hauv cov ntawv hauv qab no.

SETTINGS

Tom qab lub HMI powered on, luv luv nias "Hom" khawm ob zaug kom nkag mus rau hauv "Setting". Luv luv los yog (<0.5s) xaiv thiab tom qab ntawd luv luv nias (<0.5S) "Hom" khawm kom paub meej thiab nkag mus rau hauv qhov kev xaiv.
Nco tseg: qhov ceev yuav tsum yog "0" ces nkag mus rau qhov chaw interface.

Koj tuaj yeem nias lub khawm "Mode" (<0.5S) ob zaug txhua lub sijhawm, lossis xaiv "Rov qab" lossis "Tawm" kom tawm rov qab mus rau lub ntsiab interface.

"Setting" interface

Hauv "Setting" interface, luv luv nias (<0.5S) los yog rau xaiv "Setting" thiab nias luv luv (<0.5S) "Mode" kom paub meej thiab nkag mus rau hauv "Setting".

"Trip Reset"-set reset function rau ib qho kev mus ncig

Luv luv nias or xaiv "Trip Reset", thiab tom qab ntawd luv luv nias "Mode" nkag mus rau hauv cov khoom. Xaiv "NO" / "YES" ("YES" - kom meej, "NO"-tsis muaj kev ua haujlwm), ces luv luv nias "Hom" kom txuag thiab tawm rov qab mus rau "Setting" interface.
CEEB TOOM: lub sij hawm caij tsheb kauj vab, qhov nruab nrab ceev thiab siab tshaj plaws yog rov pib dua tib lub sijhawm.

"Unit"— teem caij rau km/mais

Luv luv nias or xaiv "Unit", thiab ces luv luv nias "Mode" nkag mus rau hauv cov khoom. Xaiv "Metric" / "Imperial", ces luv luv nias "Mode" kom txuag thiab tawm rov qab mus rau "Setting" interface.

"Brightness" - teem backlight brightness

Luv luv nias or xaiv "Brightness", thiab ces luv luv nias "Mode" nkag mus rau hauv cov khoom. Xaiv qhov percentage li "100%" / "75%" / "50%" / "30%" / "10%", ces luv luv nias "Hom" kom txuag thiab tawm rov qab mus rau "Setting" interface.
Daim ntawv ceeb toom: "10%" yog qhov ci qis tshaj plaws thiab 100% yog qhov ci ntsa iab tshaj plaws.

"Auto Off" - teem sijhawm tsis siv neeg Off

Luv luv nias or xaiv "Auto Off", thiab tom qab ntawd luv luv nias "Mode" nkag mus rau hauv cov khoom. Xaiv lub sijhawm tsis siv neeg ua haujlwm li "OFF" / "9" / "8" / "7" / "6" / "5" / "4" / ​​"3" / "2" / "1", luv luv nias "Mode "kom txuag qhov chaw thiab tawm rov qab mus rau "Setting" interface.
Daim ntawv ceeb toom: "OFF" txhais tau hais tias qhov haujlwm no raug kaw, chav tsev yog feeb.

“Assist Mode”—teem kev pab

Luv luv nias or xaiv "Assist Mode", thiab tom qab ntawd luv luv nias "Mode" nkag mus rau hauv cov khoom. Xaiv qib kev pab raws li "3" / "5" / "9", ces luv luv nias "Hom" kom txuag tau thiab tawm rov qab mus rau "Setting" interface.

“Service”— qhib/tawm qhov Service qhia

Luv luv nias or xaiv "Kev Pabcuam", thiab tom qab ntawd luv luv nias "Hom" kom nkag mus rau hauv cov khoom. Xaiv "NO" / "YES" ("YES" txhais tau tias kev qhia txog kev pab cuam nyob rau; "NO" txhais tau tias kev pab cuam tsis raug), ces luv luv nias "Hom" kom txuag thiab tawm rov qab mus rau "Setting" interface.

"Cov ntaub ntawv" interface

Hauv Kev teeb tsa interface, luv luv nias (<0.5S) or xaiv "Cov Ntaub Ntawv" thiab tom qab ntawd luv luv nias (<0.5S) "Hom" kom paub meej thiab nkag mus rau hauv "Cov Ntaub Ntawv".

View “Wheel Size”

Luv luv nias or xaiv "Los Loj", thiab tom qab ntawd luv luv nias "Hom" rau view lub log loj default, ces luv luv nias "Mode" tawm rov qab mus rau "Information" interface.

View “Speed ​​Limit”

Luv luv nias or xaiv "Speed ​​Limit", thiab ces luv luv nias "Hom" rau view qhov ceev txwv tsis pub dhau, ces luv luv nias "Mode" tawm rov qab mus rau "Information" interface.

View "Cov ntaub ntawv roj teeb."

Luv luv nias or mus rau "Cov Ntaub Ntawv Roj Teeb.", thiab tom qab ntawd luv luv nias "Mode" nkag mus, ces luv luv nias "+" lossis "-" mus rau view cov ntaub ntawv roj teeb (b01 → b04 → b06 → b07 → b08 → b09 → b10 → b11 → b12 → b13 → d00 → d01 d02 → … → dn → Hardware brief Ver → Software Verde), ces rov qab mus rau "Information" interface.
Daim ntawv ceeb toom: Yog tias lub roj teeb tsis muaj kev sib txuas lus, koj yuav tsis pom cov ntaub ntawv los ntawm roj teeb.

Code Code txhais Chav tsev
b01 ua Tam sim no kub ℃
b04 ua Total voltage mV
b06 ua Nruab nrab tam sim no mA
b07 ua Tseem muaj peev xwm mAh
b08 ua Roj teeb muaj peev xwm ntawm Full charged mAh
b09 ua Kwv yees li tus nqi percentage %
b10 ua Absolute Charge nyob rau hauv percentage %
b11 ua Cycle Times sij hawm
b12 ua Max Uncharge Time Teev
b13 ua Lub Sijhawm Uncharge Kawg Teev
d 00 ua Tus naj npawb ntawm tes  
d 01 ua Voltage Cell 1 mV
d 02 ua Voltage Cell 2 mV
dn Voltage Cell n mV
e01 ua Hardware Version  
e02 ua Software Version  

CEEB TOOM: Yog tias tsis pom cov ntaub ntawv, nws qhia "–".

View “Display Info”

Luv luv nias or xaiv "Display Info", thiab ces luv luv nias "Mode" rau view nws, luv luv nias or rau view "Hardware Ver" lossis "Software Ver", ces luv luv nias "Hom" tawm rov qab mus rau "Cov Ntaub Ntawv" interface.

View "Ctrl Info"

Luv luv nias or xaiv "Ctrl Info", thiab ces luv luv nias "Mode" rau view nws, luv luv nias or rau view "Hardware Ver" lossis "Software Ver", ces luv luv nias "Hom" tawm rov qab mus rau "Cov Ntaub Ntawv" interface.

View "Cov ntaub ntawv Torque"

Luv luv nias or xaiv "Torque Info", thiab ces luv luv nias "Hom" rau view nws, luv luv nias or rau view "Hardware Ver" lossis "Software Ver", ces luv luv nias "Hom" tawm rov qab mus rau "Cov Ntaub Ntawv" interface.
CEEB TOOM: Yog tias koj lub Pedelec tsis muaj lub zog torque, ces "Torque Info" tsis tuaj yeem tso tawm.

View “Yam Code”

Luv luv nias or xaiv "Yuam Kev Code", thiab ces luv luv nias "Hom" rau view nws, luv luv nias or rau view cov lus ntawm kev ua yuam kev rau kaum zaug dhau los ntawm "E-Code0" rau "E-Code9", tom qab ntawd luv luv nias "Hom" kom tawm rov qab mus rau "Cov Ntaub Ntawv" interface.
CEEB TOOM: 00 txhais tau tias tsis muaj qhov yuam kev.

View “Warn Code”

Luv luv nias or xaiv "Warn Code", thiab luv luv nias "Hom" rau view nws, luv luv nias or rau view cov lus ceeb toom rau kaum zaus dhau los ntawm "W-Code0" rau "W-Code9", tom qab ntawd luv luv nias "Hom" tawm rov qab mus rau "Cov Ntaub Ntawv" interface.

YUS CODE DEFINITION

HMI tuaj yeem qhia qhov ua txhaum ntawm Pedelec. Thaum kuaj pom qhov yuam kev, ib qho ntawm cov lej yuam kev hauv qab no yuav raug qhia rau ntawm txoj haujlwm ntawm cov zaub ceev.

Nco tseg: Thov nyeem ua tib zoo nyeem cov lus piav qhia ntawm qhov yuam kev. Thaum qhov yuam kev code tshwm, thov ua ntej pib lub kaw lus. Yog tias qhov teeb meem tsis raug tshem tawm, thov hu rau koj tus neeg muag khoom lossis cov neeg ua haujlwm.

yuam kev Tshaj tawm Kev daws teeb meem
04 Lub throttle muaj txhaum.
  1. Xyuas cov connector thiab cable ntawm lub throttle tsis puas thiab raug kev cob cog rua.
  2. Disconnect thiab reconnect lub throttle, yog tias tseem tsis muaj nuj nqi thov hloov lub throttle.
05 Lub throttle tsis rov qab rau hauv nws txoj haujlwm raug. Kos lub connector los ntawm lub throttle yog raug txuas. Yog tias qhov no tsis daws qhov teeb meem, thov hloov lub throttle.
07 Overvoltage kev tiv thaiv
  1. Tshem tawm thiab rov ntxig lub roj teeb kom pom tias nws daws qhov teeb meem.
  2. Siv cov cuab yeej BESST hloov kho tus maub los.
  3. Hloov lub roj teeb los daws qhov teeb meem.
08 Kev ua yuam kev nrog lub teeb pom kev hauv tsev hauv lub cev muaj zog
  1. Xyuas tag nrho cov connectors los ntawm lub cev muaj zog txuas kom raug.
  2. Yog tias qhov teeb meem tseem tshwm sim, thov hloov lub cev muaj zog.
09 Yuam kev nrog lub cav theem Thov hloov lub cev muaj zog.
10 Qhov kub hauv lub cav tau mus txog nws qhov kev tiv thaiv siab tshaj plaws
  1. Tua lub kaw lus thiab cia Pedelec txias.
  2. Yog tias qhov teeb meem tseem tshwm sim, thov hloov lub cev muaj zog.
11 Qhov ntsuas kub ntsuas hauv lub cev muaj qhov yuam kev Thov hloov lub cev muaj zog.
12 Yuam kev nrog lub sensor tam sim no hauv tus maub los Thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
13 Yuam kev nrog lub ntsuas kub ntsuas hauv lub roj teeb
  1. Xyuas tag nrho cov connectors los ntawm lub roj teeb kom raug txuas nrog lub cev muaj zog.
  2. Yog tias qhov teeb meem tseem tshwm sim, thov hloov lub roj teeb.
14 Kev tiv thaiv kub hauv lub maub los tau mus txog nws qhov kev tiv thaiv siab tshaj plaws
  1. Cia lub pedelec kom txias thiab rov pib lub system.
  2. Yog tias qhov teeb meem tseem tshwm sim, thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
15 Kev ua yuam kev nrog lub ntsuas kub ntsuas hauv lub maub los
  1. Cia lub pedelec kom txias thiab rov pib lub system.
  2. Yog tias qhov teeb meem tseem tshwm sim, Thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
21 Ceev sensor yuam kev
  1. Rov kho qhov system
  2. Txheeb xyuas tias cov hlau nplaum txuas nrog cov lus hais tau ua raws li qhov ntsuas nrawm thiab qhov kev ncua deb ntawm 10 hli thiab 20 hli.
  3. Txheeb xyuas tias qhov ceev sensor txuas txuas raug raug.
  4. Txuas lub pedelec mus rau BESST, saib seb puas muaj lub teeb liab los ntawm qhov ntsuas ceev.
  5. Siv cov cuab yeej zoo tshaj plaws- hloov kho tus maub los saib seb nws puas daws qhov teeb meem.
  6. Hloov lub sensor ceev kom pom tias qhov no tshem tawm qhov teeb meem. Yog tias qhov teeb meem tseem tshwm sim, thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
25 Torque teeb liab yuam kev
  1. Txheeb xyuas tias txhua qhov kev sib txuas tau txuas raug raug.
  2. Thov txuas lub pedelec mus rau BESST system saib seb puas tuaj yeem nyeem tau los ntawm BESST cuab yeej.
  3. Siv cov cuab yeej BESST hloov kho tus maub los saib seb nws puas daws qhov teeb meem, yog tias tsis yog thov hloov lub torque sensor lossis tiv tauj koj tus neeg muag khoom.
26 Lub teeb liab ceev ntawm lub torque sensor muaj qhov yuam kev
  1. Txheeb xyuas tias txhua qhov kev sib txuas tau txuas raug raug.
  2. Thov txuas lub pedelec mus rau BESST system kom pom tias lub teeb liab ceev tuaj yeem nyeem tau los ntawm BESST cov cuab yeej.
  3. Hloov cov Zaub kom pom seb qhov teeb meem puas daws tau.
  4. Siv cov cuab yeej BESST hloov kho tus maub los saib seb nws puas daws qhov teeb meem, yog tias tsis yog thov hloov lub torque sensor lossis tiv tauj koj tus neeg muag khoom.
27 Overcurrent los ntawm maub los Siv cov cuab yeej BESST hloov kho tus maub los. Yog tias qhov teeb meem tseem tshwm sim, thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
30 Kev sib txuas lus teeb meem
  1. Xyuas tag nrho cov kev sib txuas ntawm lub pedelec yog txuas kom raug.
  2. Siv cov cuab yeej BESST khiav qhov kev kuaj mob, saib seb nws puas tuaj yeem pom qhov teeb meem.
  3. Hloov cov zaub kom pom seb qhov teeb meem puas daws tau.
  4. Hloov EB-BUS cable kom pom tias nws daws qhov teeb meem.
  5. Siv cov cuab yeej zoo tshaj plaws, rov hloov kho cov tswj software. Yog tias qhov teeb meem tseem tshwm sim, thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
33 Nres teeb liab muaj qhov yuam kev (Yog tias nres sensors haum)
  1. Xyuas tag nrho cov connectors raug txuas rau ntawm tus brakes.
  2. Hloov cov brakes saib seb qhov teeb meem puas daws tau.

Yog tias muaj teeb meem txuas ntxiv thov hloov tus tswj lossis tiv tauj koj tus neeg muag khoom.
35 Kev kuaj xyuas Circuit Court rau 15V muaj qhov yuam kev Siv cov cuab yeej BESST hloov kho tus maub los saib seb qhov no daws qhov teeb meem. Yog tias tsis yog, thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
36 Kev kuaj xyuas Circuit Court ntawm lub keypad muaj qhov yuam kev Siv cov cuab yeej BESST hloov kho tus maub los saib seb qhov no daws qhov teeb meem. Yog tias tsis yog, thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
37 WDT Circuit Court yog faulty Siv cov cuab yeej BESST hloov kho tus maub los saib seb qhov no daws qhov teeb meem. Yog tias tsis yog, thov hloov tus maub los lossis tiv tauj koj tus neeg muag khoom.
41 Total voltage los ntawm lub roj teeb siab dhau lawm Thov hloov lub roj teeb.
42 Total voltage los ntawm lub roj teeb tsawg dhau Thov them lub roj teeb. Yog tias qhov teeb meem tseem tshwm sim, thov hloov lub roj teeb.
43 Tag nrho lub zog los ntawm cov roj teeb hlwb siab dhau lawm Thov hloov lub roj teeb.
44 Voltage ntawm ib leeg xwb siab dhau lawm Thov hloov lub roj teeb.
45 Kub los ntawm lub roj teeb siab dhau lawm Thov cia lub pedelec txias.
Yog tias tseem muaj teeb meem, thov hloov lub roj teeb.
46 Qhov kub ntawm lub roj teeb qis dhau lawm Thov nqa lub roj teeb rau hauv chav tsev kub. Yog tias qhov teeb meem tseem tshwm sim, thov hloov lub roj teeb.
47 SOC ntawm lub roj teeb siab dhau lawm Thov hloov lub roj teeb.
48 SOC ntawm lub roj teeb tsawg dhau lawm Thov hloov lub roj teeb.
61 Switching detection defect
  1. Xyuas kom lub gear shifter tsis jammed.
  2. Thov hloov lub iav shifter.
62 Electronic derailleur tsis tuaj yeem tso tawm. Thov hloov lub derailleur.
71 Electronic xauv yog jammed
  1. Siv cov cuab yeej BESTT hloov kho cov Zaub kom pom tias nws daws qhov teeb meem.
  2. Hloov cov zaub yog qhov teeb meem tseem tshwm sim, thov hloov lub ntsuas hluav taws xob.
81 Bluetooth module muaj qhov yuam kev Siv cov cuab yeej zoo tshaj plaws, rov hloov kho cov software rau hauv cov zaub kom pom tias nws daws qhov teeb meem.
Yog tsis yog, Thov hloov cov zaub.

WARN CODE DEFINITION

Ceeb toom Tshaj tawm Kev daws teeb meem
28 Torque sensor qhov pib pib yog qhov txawv txav. Restart lub kaw lus thiab nco ntsoov tsis txhob ua rau lub crank nyuaj thaum rov pib dua.

Cov ntaub ntawv / Cov ntaub ntawv

BAFANG DP C262.CAN zaub [ua pdf] Tus neeg siv phau ntawv
DP C262.CAN zaub, C262.CAN zaub, zaub

Cov ntaub ntawv

Related Posts

Cia ib saib

Koj email chaw nyob yuav tsis raug luam tawm. Cov teb uas yuav tsum tau muaj yog cim *